Transmission
Transmission
Transmission
UNIT I
Contents
Introduction
Transmission Systems
Manual
Automated Manual
Automatic
Continuously variable
Dual Clutch
Propeller Shaft
2
Contents
Universal joints
Differential
Requirements of the Transmission Design Process
Product Life Cycle
Stages in the Design Process
Project Set Up
Concept Design
Detailed Design
Engineering Drawings and Tolerancing
3
Transmission System
Function of transmission:
- It is used to transmit engine torque to the drivin
wheels to drive the vehicle on the road.
4
Requirement of Transmission System
To provide for disconnecting the engine from t
riving wheels
6
Transmission Types
7
Clutch
Function of clutch
Clutch is used to disengage and engage th
ngine with rest of the transmission systems.
8
Clutch
Requirement of Clutch
Transmit maximum torque of the engine.
Dynamically balanced.
As small as possible.
Easy to operate.
9
Clutch Unit
Flywheel also acts as a driving
member
Pressure plate is connected to
clutch cover assembly.
Clutch Cover assembly is bolted to
the flywheel.
Clutch springs placed between
Pressure plate & Cover plate, press
the Pressure plate against the
clutch plate.
Thus Clutch plate is squeezed
between Flywheel & Pressure plate.
Classification of Clutch
Cone clutch
Flat Plate clutch
- Dry or Wet type clutch
- Actuation spring(Helical
or Diaphragm)
Centrifugal clutch
11
Clutch Engaged & Disengaged
Clutch is always is in
engaged state.
It can be disengaged by
pressing of Clutch pedal.
Disengagement is effecte
by non - contact of Clutch
plate both with Flywhee
face & Pressure plate face
Frictional heat is
dissipated by openings
present in Clutch housing
& Cover
12
Clutch Material
13
Need of Gear Box
14
Gear Box
Gear box varies the leverage
(speed ratio & hence torque
ratio) between the engine &
driving wheels.
16
UNIT II
Synchronizers
A device used to bring two adjacent members to
the same speed before allowing the sleeve to
engage them.
The two elements are friction clutch and toothed
clutch.
Lock the positive engagement until speeds are
synchronized .
Establish the positive engagement and power flow.
Synchronizer is splined on the shaft Cone on the
gear (blue) fits into cone-shaped area in the collar.
Friction between the cone and collar synchronize
the collar & gear.
The outer portion of the collar (sleeve) then slides
so that the dogteeth engage the gear.
17
Synchromesh Gearbox
18
How Manual Transmission Work?
When a driver wants to change from one gear to anoth
in a standard stick-shift car, he first presses down th
clutch pedal
his operates a single clutch, which disconnects th
ngine from the gearbox and interrupts power flow to
ransmission
hen the driver uses the stick shift to select a new gea
process that involves moving a toothed collar from on
gear wheel to another gear wheel of a different size
Devices called synchronizers match the gears befo
they are engaged to prevent grinding
Once the new gear is engaged, the driver releases th
clutch pedal, which re-connects the engine to th
gearbox and transmits power to the wheels.
19
Manual Transmission
Cheap to make
Durable, efficient
Easy to install
Elimination of Clutch
Pedal
Modification of Gear
Shifting lever
Minimum
modifications in
manual transmission
21
AMT Features
Automation of Clutch operation and Gea
hifting.
23
Clutch Actuation Control
Engine Start
- Starter should be operated only when the gear
in neutral position
- When engine is not running and in power on, EC
will disengage clutch
- When engine speed exceeds a specified rpm, EC
engages clutch gradually
Vehicle Start
- On pressing the accelerator pedal, ECU controls
the clutch
- actuator travel and clutch engagement
24
Clutch Actuation Control
Gear Change
- While engaging the clutch after gear
shift, the ECU determines clutch actuator
travel based on shifted gear position and
accelerator pedal stroke
Clutch disengagement
- While gear shifting and when accelerato
pedal is released,
- if the vehicle speed is lower than a set
speed for select gear position, the ECU
disengages clutch
25
Advantages of AMT
Reduced driver effort
26
Automatic Transmission (AT)
Conventional Definition
Moving away from rest - Torque converter
No power interruption
Basic components.
- outer shell or housing,
- impeller or pump and turbine or runner
Both of these units are contained within the
housing via oil-tight seals.
The input turbine is connected to the power
supply, typically an electric or ICE.
The output turbine is connected to the drive train
of the vehicle or the drive system of a machine.
Mineral oil is used
28
Fluid Coupling: Working
Standstill
- The entire operating fluid in the
coupling is at rest
Idling
- In sufficient centrifugal force for the
oil to turn the turbine
Low to medium speed:
- Centrifugal force pushes oil into
turbine and some turning effort is
transmitted. Large degree of slip in
the unit. O/p shaft is rotating slowly
than input shaft.
Medium to High Speed
- Oil force is sufficient to transmit full
power. O/p shaft rotating at about
98% of speed of I/p shaft (2% slip).
29
UNIT III
Torque Convertor
Serves as automatic clutch which transmits
engine torque to the transmission input shaft
Multiplies torque generated by the engine
Absorbs torsional vibration of engine
Acts as a flywheel and smoothes out engine
rotation
Drives oil pump
A torque converter consists of
- Impeller
- Turbine
- Stator
- and transmission fluid
30
Torque Convertor - Sectional Vie
31
Impeller
32
Turbine
33
Stator
34
Working of Torque Convertor
Vehicle accelerates
35
Planetary Gear System
36
Planetary Gear System: Constructio
Input shaft is connected to Ring gear(Blue)
Output shaft is connected to Plane carrier(Green) which is also
connected to Multi-disk clutch
Sun gear is connected to a Drum(Yellow), which can be locked
by brake band (Red). It is also connected to the other half of
Clutch
37
Planetary Gear System: Operatio
In Neutral
Both
band and clutch sets are released
Planets
assembled to carrier with NRB
Ring
gear only drive planet gear not the planet carr
(Output shaft)
The planet gears drive the sun gears to spin freel
38
Planetary Gear System: Operatio
In Low Gear (forward reduction)
Band locks the sun gear by locking the drum
Planets walk around the sun gear
Planet carrier to spin in same direction as ring gear
Gear ratio= sun & ring teeth/no of teeth of ring gear
39
Planetary Gear System: Operatio
In High Gear (Direct drive)
Band is released.
Lock any two members
Clutch is engaged so that the sun gear and planet
carrier is locked to act as a rigid member
Planets has to walk around the ring gear,
Ring Gear (Input shaft) will spin at the same speed
the Planet Carrier (Output shaft)
40
Planetary Gear System: Operation
Reverse Gear
Planet carrier is locked
Ring gear (Input shaft) will cause the sun gear
(Output Shaft) to turn in the opposite direction
41
UNIT IV
Automatic Transmission (AT)
Advantages
The only option for comfortable automatic shifting
Cost issue mitigated by high volume manufacturing
Disadvantages
Cost for development and manufacturing
Fuel economy due to torque converter
Lack of control by the driver
Modern improvements
Better control algorithms
Torque converter lock up
42
Continuously Variable Transmissio
(CVT)
CVT provides infinite
number of gear ratios
(between a minimum & a
maximum).
Seamless power
delivery, no torque
interruption & power loss
43
CVT: Construction
Uses a pair of axially
adjustable sets of
pulley halves
(Variators)
A belt is used to
transfers the engine's
power from one shaft
to another
44
CVT: Functioning
The transmission ratio is varied by
adjusting the spacing between the
pulleys in line with the circumference
of the tapered pulley halves.
The variators are adjusted
hydraulically.
When one pulley is varied, the other
pulley must adapt itself inversely since
the length of the belt is fixed.
Dual Clutch Transmission (DCT
46
DCT: Construction
Basic Dual Wet Clutch
How DCT Works?
In a conventional manual transmission, there is not a
continuous flow of power from the engine to the wheels.
Instead, power delivery changes from ON to OFF to ON during
gearshift, causing a phenomenon known as "shift shock" or
"torque interrupt
A dual-clutch transmission uses two clutches, but has no clutch
pedal.
Sophisticated electronics and hydraulics control the
clutches, just as they do in a standard automatic transmission.
In a DCT, however, the clutches operate independently
One clutch controls the odd gears(first, third, fifth and
reverse), while the other controls the even gears
(second, fourth and sixth)
Using this arrangement, gears can be changed without
interrupting the power flow from the engine to the transmission
49
Propeller Shaft
Single piece
Two piece
Front engine rear wheel drive
Reduction in car height
(lowering of body)
Crash energy management
Material
Aluminum
steel
Composite (75% carbon, 25%
glass-fibre with bonded steel
end fittings- Renault)
Cold rolled and seam
welded
50
Propeller Shaft
It propels the vehicle forward, so called propeller shaft
A Propeller Shaft connects a gearbox to a Differential.
It is used to transmit the drive force generated by the engine
to the axles.
It is strong enough to handle maximum low gear torque
It is provided with two U-joints to maintain constant velocity
and positioning of differential at different plane.
It is provided with a slip joint to take care of the change in
length.
Shaft diameter and its thickness decides the torque carrying
capacity and angle of operation.
51
Propeller Shaft
Design requirements
Critical speed is at least 15% above top
speed
Torque carrying capacity requirements
Plunge requirements (suspension travel
Assembly requirements
52
Universal joints
Designed to eliminate
torque and speed
fluctuations (constant
velocity joints)
If only one universal joint is
used, speed fluctuations
will not be neutralized.
To maintain uniform
motion, two universal joints
are used with yoke lugs in
phase.
53
Universal joints
54
Hookes Joint
58
Axle
Transmits rotary motion and torque from t
ngine-transmission-driveshaft to the wheels
Changes torsional direction from longitudinal
ansverse
Provides speed reduction and torque
multiplication
Provides a differential action to permit veh
rnering
Provides mounting points for suspension a
akes
59
Transmission Troubleshooting
Leaking Transmission Fluid
Slipping of Transmission
Damaged Transmission Fluid
Surging of Transmission
Gear Problems
Fluid Leaking
Spilling out of Fluid
Erratic Gear Shifting
Overheating of Transmission
60
Transmission Trend
Passenger Car Transmission in India
ual transmission is more dominant in India as compared to other
missions.
Majority of the MT are using 5speed GB as compared to 6 speed
ut many of the luxurious car manufactures are now using AMT o
2005 2010
3%
7% 10% MT
AT
43%
CVT
DCT
37%
AMT
2015
Requirements of the Transmission
Design Process
Product Life Cycle
64
Stages in the Design Process
Timeline
Project set up
Concept design
Detail design
Tolerancing &
drawings
Prototype testing
65
UNIT V
Project Set Up
- The first stage of the design process is to set
targets
Existing product knowledge
Market research Product Design Specification
Standards
Load data (PDS)
Customer specific requirements
- The PDS contains all the specification data and design
targets
This document should be approved before work star
on concept design
- The PDS is a live document
This means that changes can be made to it, providin
all parties agree to them
66
Project Set Up
To be included in the Product Design Specification
Understanding the customer
needs/wants from - Special considerations
- Customer PDS - Review all validation testing
for unusual manoeuvres
(Vehicle/Transmission)
Rig
- Market Understanding
Vehicle
- Prior Design Experience
Special environmental operation
General Requirements conditions, eg:
- Number of gear ratios and their - Very high or very low ambient
values temperature conditions
- Packaging envelope constraints - Extremely tight vehicle
- Weight packaging space
Special operational cycles, eg:
- Application specifics
- Unusual off-road usage
- Duty cycle
- Occasional vehicle overload
- Interfaces operation
Gear ratio must be defined.
67
Project Set Up
To be included in the Product Design Specification:
- It may not be possible to meet all requirements, so defi
the hierarchy of importance, normally (approximately):
Packaging within the vehicle
Assemble-ability
Durability
Ratio
Weight
Cost
Gear shift quality
Noise
68
Project Set Up
To be included in the Product Design Specification:
Design Loads & Duty Cycles
- A design load case may be comprised of a series of loads and
cycles/time at those loads combined into a duty cycle definition
Design loads are typically modified somewhat
- Maximum net engine output torque including
Reserve capacity for enhanced engine torque or larger engin
application: 0% to 10% typical
Factor for unusually high engine torsionals output: 0% to 5
typical
- Maximum vehicle skid torque
Max skid torque in each gear for operation on dry, new concre
Usually only significant in lowest ratios (eg: 1st, Reverse)
- Maximum transient overload torque (static overload only)
Factors vary according to specific vehicle and are genera
based off of historical vehicle test results
Typical values range from 1.5x to 2.5x maximum engine torque
69
Project Set Up: Duty Cycle
A key component of the targets is the Duty Cycle
What is a Duty Cycle?
- Calculation of Component Reliability - single loadca
Material
Properties
Operating
Conditions
Select
Required
Reliability
Analysis to
Component Operating Analysis to
predict
Geometry Stresses predict life
stress
Applied
Loads (Duty
Cycle)
70
Project Set Up: Duty Cycle
A Duty Cycle is a collection of loadcases
- All automotive transmissions are loaded with multip
loadcases
- Multiple ratios
- Different torque levels for each ratio
10%, 20%, 30% 100% torque
Accounting for Multiple-loadcases - Damage
- Miners Rule (Linear Damage Hypothesis)
To combine the effect of different loadcases
Damage Fraction & Percentage
We need to account for the effect of these many loadcase
71
Project Set Up: Duty Cycle
In-service Loads must be converted into a du
cycle for design and testing
Durability
In-Service Loads Calculation Design Duty Cycle
Time/torque To derive the Equivalent duty cycle
history for the 95th damage for each appropriate for
centile component in the transmission design
transmission
72
Concept Design
Activities within Concept Design (part A)
Design gear Synchroniser Spline
teeth and design, sizing design
blanks and and and
Inputs from dog teeth packaging rating
PDS:
Gear ratios Can
Create ratios Yes Output:
Engine
torque and initial Iterative Design and Proposed
duty cycle gearbox of the Gearbox packagin concept
3D Concept g be layout
concept
packaging achieved
space
?
Define Define No
shaft roller
sections bearings
73
Concept Design
Generation of Design Options (Layouts/ Topology)
- Create as many different design layouts as possib
to meet the ratio and packaging requirements
74
Concept Design
Iterative Design, Analysis and Optimisation, by CA
- Gears - Synchronizers
Tooth numbers Shift force
Rating to ISO 6336 Cone to index torque
Contact Ratio targets ratio
Misalignment targets
- Bearings
- Shaft Durability
Durability Misalignment targets
Deflection
- Spline
Stress
75
Concept Design
Activities within Concept Design (part B)
Casing
Design and
Differential
Shift
Proposed Concept Layout Mechanism
Check for
Completed
compatibility
withand with
other vehicle
components
Concept
packaging; Check for Design
Assembly Rank against
PDS, other
Iterate on items defined in
Concept Design Part A if designs
necessary
Once the concepts have been modelled and analysed, their stren
and weaknesses can be evaluated
The selected concept will then form the basis for the detailed de
76
Concept Selection
Evaluation criteria
List all the requirements for the design from t
specification
77
Concept Selection
Concept scoring
Assign a score to each concept according to t
extent to which it meets each requirement
78
Detailed Design
Activities within Detailed Design
Focus on system deflections and gear micro-geomet
design
Gear Micro-
Differential
geometry Design
Detailing
Completed
Detailed
FE, System Deflection
and Gear Tooth Design, all
Completed Concept Design Casing Detailing
Contact Detailed Nominal
Analysis Dimensions
Complete
Detailed Design and
Analysis of Other
Components;
Lubrication system Check for
compatibility with
other components
79
Detailed Design
Calculation of System Deflections
Load
distribution
Shaft
deflection
Load distribution
factor
Contact
Stress
Stress
Calculation of Durability
80
Detailed Design
Accurate analysis is required to determine wheth
targets are met
Simple methods do not give accurate results
- Increased risk of problems later in product life cycle
- Lack of clear direction for optimisation
81
Analysis Methods
Principles
86
Engineering Drawings and Tolerancin
87
Engineering Drawings and Tolerancin
Tolerance Stacks
Identify
checks required
Gear and shaft
Create master
deflections from
dimension sheet
analysis Final design
Create tolerance
stacks for each
shaft assembly Yes
Revise dimensions
Check result No on master No Check result
dimension sheet
Yes No
Create tolerance
Create housing
stacks for shaft to Check result Yes
shaft clearances
tolerance stacks
88
Engineering Drawings and Tolerancin
Potential Problems
- Action:
Small iteration: Redefine the tolerances
Large iteration: Nominal dimensions are redefine
89
Engineering Drawings and Tolerancin
Potential Problems
Form and functionality at tolerance, temperat
xtremes, under load
- Symptom (example): Transmission does not assem
or there is a foul at:
Tolerance extremes
Temperature extremes
Load (i.e. deflected shapes)
- Example: Gears clash due to thermal expansion an
axial movement due to compliance of
bearings, housing etc.
- Action (as before)
90
Output of Design Process
A layout that satisfies the key requirements of the PDS
3D
models complete with all components defined to nomin
dimensions
91
THANK
YOU