Scribd
Upload
310 views

Microprocessor 8085 Architecture

The 8085 microprocessor architecture consists of the following main components: registers including the accumulator and flag register, an ALU, an instruction decoder, an address buffer, an address/data buffer, an increment/decrement latch, interrupt control, serial I/O, and a timing and control circuit. The accumulator is an 8-bit register used for arithmetic/logical operations and data transfer. There are six general purpose registers (B, C, D, E, H, L) that can also be combined as register pairs. The program counter is a 16-bit register that sequences instruction execution by pointing to the next memory location. The stack pointer is a 16-bit register that points to memory locations in the stack used

Uploaded by

SindhujaSindhu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
310 views

Microprocessor 8085 Architecture

The 8085 microprocessor architecture consists of the following main components: registers including the accumulator and flag register, an ALU, an instruction decoder, an address buffer, an address/data buffer, an increment/decrement latch, interrupt control, serial I/O, and a timing and control circuit. The accumulator is an 8-bit register used for arithmetic/logical operations and data transfer. There are six general purpose registers (B, C, D, E, H, L) that can also be combined as register pairs. The program counter is a 16-bit register that sequences instruction execution by pointing to the next memory location. The stack pointer is a 16-bit register that points to memory locations in the stack used

Uploaded by

SindhujaSindhu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 19

Basic Processor

Architecture of
8085(p)

8085 Microprocessor Architecture

The architecture of 8085 consist various components


like.
1:Register and accumulator.
2:ALU.
3:Instruction decoder and machine cycle encoder.
4:Address buffer.
5:Address/data buffer.
6:Inc/Dec latch.
7:Interrupt control.
8:Serial i/o like SOD,SID.
9:Timing and Control circuit.

Accumulator:
The accumulator is an 8-bit register
then is part of the arithmetic/logic
unit(ALU).
This register is used to store to store 8-bit
data this data is used to perform arithmetic
& logical operation.
The result of an operation is stored in the
accumulator.
The accumulator is also identified as
register A.
The accumulator is used for data transfer
between an I/O port and memory location.

Registers
The 8085 simulator has six general-purpose registers to
store 8-bit data; these are identified as B, C, D, E, H
and L. They can be combined as register pair BC, DE
and HL to perform some 16-bit operations.
The programmer can use these registers to store or copy
data into the registers by using data copy instructions.
Out of these six registers, four 8-bit registers are scratch
pad registers which are accessible to the programmer and
hence can be used to store data during a program
execution.
And the two registers H and L are similar to that of
scratch pad register but they are utilized in indirect
addressing mode. In this mode, the memory location i.e.
the address is specified by the contents of the registers.

Program Counter (PC):


This 16-bit register deals with sequencing the execution
of instructions. This register is a memory pointer.
Memory locations have 16-bit addresses, and that is
why this is a 16-bit register.
The microprocessor uses this register to sequence the
execution of the instructions. The function of the
program counter is to point to the memory address from
which the next instruction is to be fetched. When a byte
(machine code) is being fetched, the program counter is
incremented by one to point to the next memory
location.

Stack Pointer (SP)


The stack pointer is also a 16-bit register
used as a memory pointer. It points to a
memory location in R/W memory, called
the stack.
This includes, but is not limited to:
the return address.
a place for a return value.
passed parameters.
local variables.

The return address of the PC from where the


program control was transferred to the subroutine
this return address is kept in a special area called
stack.
returns.
Interrupt calls and returns.
code explicitly pushing and popping entries.
direct manipulation of the SP register.
Consider the following program in my (fictional)
assembly language:
Stack pointer is a special purpose 16-bit register
in the Microprocessor, which holds the address
of the top of the stack.

stack pointer useful when interrupt


occur i.e. before execution of call
instruction address of next
instruction is copied into stack
pointer.
This register is always
increment/decrement by 2.
Incrementor decrementor. This is
also 16 bit resistor. It is used to add
or subtract one from the contents of
the program counter or stack
pointer. .

Flags or status resistor:


The ALU includes five flip-flops, which are set
or reset after an operation according to data
conditions of the result in the accumulator and
other registers. They are called Zero(Z), Carry
(CY), Sign (S), Parity (P), and Auxiliary Carry
(AC) flags.
The most commonly used flags are Zero, Carry,
and Sign. The microprocessor uses these flags
to test data conditions.

For example, after an addition of two


numbers, if the sum in the accumulator id
larger than eight bits, the flip-flop uses to
indicate a carry -- called the Carry flag
(CY) -- is set to one.
When an arithmetic operation results in
zero, the flip-flop called the Zero(Z) flag is
set to one.
The first Figure shows an 8-bit register,
called the flag register, adjacent to the
accumulator..

Flag is an 8-bit register containing 5 1-bit flags:


Sign - set if the most significant bit of the result
is set.
Zero - set if the result is zero.
Auxiliary carry - set if there was a carry out from
bit 3 to bit 4 of the result.
Parity - set if the parity (the number of set bits in
the result) is even.
Carry - set if there was a carry during addition,
or borrow during subtraction/comparison.

Serial i/o control


These are control signals used for controlling
8085
these are subdivided into 2 types
1)SID(serial input data):this is used for
transferring of data into the memory serially.
2)SOD(serial output data):this is used for
transferring of data from memory to external
devices
Interrupt control is used to transfer the ISR to
the CPU.

Instruction resister or Decoder:Once the instruction is fetch from the


memory, it is reloaded in the
instruction resistor for some time,
after the decoder decode the
instruction performing some event or
task.
Address buffer:
The remaining higher order address
lines form the address buffer ranging
from[A15-18].This is having the
unidirectional buffer

Address/data buffer:
The address bus will be having 16 address
lines[A15-A0] .In which A7-A0 are called as
lower addressing lines and these are
multiplexed with data lines[D7-D0] to form
multiplexed address /data buffer .The
address/data buffer is the bidirectional bus.
Timing and Control Unit:
The timing and control unit accepts information
from the instruction decoder and
generates different control signal. This unit
synchronizes all the microprocessor operation
and generates control and status signal
necessary for communication between the
microprocessor and peripherals.

In this way the architecture of 8085 is


studied

Thank
you

You might also like