Wavelets Lecture - Clean

Wavelets
Chapter
7
You guys arent drilling that hard streak, are

you?
Introduction
The objective of this section is to discuss and
understand wavelets. This will include:
The amplitude and phase spectrum
Zero, minimum, mixed and reverse phase
wavelets
How wavelets can affect the seismic response
Chapter 7: Wavelets
What is a wavelet?
A wavelet is a limited-duration
time series that approximates
the response of seismic energy
at a lithologic boundary. A
wavelet convolved with a
reflection coefficient should
approximate an actual seismic
reflection.
A wavelet can be approximated by a sum of cosine waves.
A wavelet can be described by its amplitude and phase spectra.
Chapter 7: Wavelets
Waves
To start our review of wavelets, lets first consider waves.
The cosine function is defined as the x coordinate of a
particle moving around a circle whose radius is 1.
y
+1
+1
+360
+90
+90
+270
+180 +270 +360
+180
Here the horizontal axis is angle . In future

graphs, the horizontal axis will be time.
Chapter 7: Wavelets
Waves: Frequency
1 sec.
+1 sec.
1 sec.
+1 sec.
The top wave has a frequency of 2 Hz.

The lower wave has a frequency of 4 Hz.
Both waves have amplitudes of 1.
Chapter 7: Wavelets
Amplitude
How would we plot the amplitude spectra

of these cosine waves?
2
1
Frequency
5
Waves: Amplitude
+1 sec.
1 sec.
+1 sec.
How would we plot the amplitude

spectra of these cosine waves?
The top wave has an amplitude of 1.

The lower wave has an amplitude of 2.
Both waves have frequencies of 2 Hz.
Chapter 7: Wavelets
Amplitude
1 sec.
2
1
Frequency
6
Waves: Phase
0
Zero Phase
1 sec.
+360
180
90
+90
90 Phase
1 sec.
+180
+270
+1 sec.
180
90
+360
+90
+180
+1 sec.
+270
A normal cosine wave has its peak amplitude at time 0.

If the peak amplitude is at a different time, we say that the phase is shifted.
A wavelets phase refers to its peak, trough, or position elsewhere on the wave.
A waves phase at time zero is called the phase of the wave.
What is the phase of the upper wave?
The upper wave has zero phase.
What is the phase of the lower wave?
The lower wave has 90 phase.
Chapter 7: Wavelets
Waves: Phase
0
Zero Phase
180
90
+90
90 Phase
1 sec.
+270
+1 sec.
180
90
How would we plot the phase

spectra of these waves?
The upper wave has zero phase.
What is the phase of the lower wave?
The lower wave has 90 phase.
Both waves have frequencies of 2 Hz.
Chapter 7: Wavelets
+180
+360
+90
+180
+1 sec.
+270
+180
+90
Phase
1 sec.
+360
90
180
2
4
Frequency
8
Waves: Amplitude and Phase

What are the amplitude and phase spectra of the following cosine
wave?
1 sec.
+1 sec.
+90
Phase
Amplitude
+180
90
180
Chapter 7: Wavelets
2
4
Frequency
2
4
Frequency
Summing Cosine Waves
0
Chapter 7: Wavelets
Sum
Lets see what happens when we add cosine waves of different frequencies
together. The sum of three cosine functions (upper left) provides a rather oddlooking waveform (lower left). However the sum of cosine functions from 5 to 65
Hz (upper right), incrementing by 5 Hz, looks more like a seismic wavelet!
0
10
Amplitude and Phase Spectra
Amplitude Spectrum
Chapter 7: Wavelets
The wavelet is decomposed into the

amplitude and phase components. Since
the amplitude of each cosine is 1, the
amplitude spectrum consists of a series of
spikes or dots of amplitude 1. The spikes
are located at the frequency corresponding
to that of each cosine function. The phase
of each cosine is 0 and is illustrated in the
phase spectrum by a point at 0 at each
frequency.
Phase Spectrum
11
Summing Cosine Waves
0
Chapter 7: Wavelets
Sum
As in a previous slide, each component cosine in the wavelet on the left has the
same amplitude. On the right, we have varied the amplitudes of each component
cosine. The 30-Hz cosine (in bright green) has the highest amplitude. What has
happened to the wavelet amplitudes away from the central peak?
0
12
Amplitude Spectra
Here we compare the sum of waves of equal amplitude with waves of varying amplitude. Note
the decreased side-lobe energy in the latter. In both cases, the wavelets are zero-phase.
Chapter 7: Wavelets
13
Phase
Similarly, right, the sum of several 90 cosine waves of varying amplitudes results
in a +90 wavelet.
0
Sum
Zero-Phase
+90 Phase
Phase-shifting a cosine wave by 90 is equivalent to a time shift.

Phase-shifting a wavelet by 90, however, gives a very different curve!
Chapter 7: Wavelets
14
Zero-Phase Wavelet
Any wavelet can be expressed in terms of amplitude and phase. Below are the
amplitude and phase spectra of a 30-Hz. Ricker wavelet. Note that the wavelet is
displayed in time, while amplitude and phase are displayed in terms of frequency.
Symmetric about
Zero Time.
This wavelet has
Zero Phase.
Negative Time
Phase
Increasing Frequency
Chapter 7: Wavelets
Positive Time
Amplitude
Increasing Frequency
15
15
The Ricker Wavelet

The Ricker wavelet (or Mexican-hat wavelet) is the
negative of the 2nd derivative of the Gaussian function:
1
0.9
0.8
Gaussianfunction
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-5
-4
-3
-2
-1
0.8
0.6
1st derivative
0.4
0.2
0
-5
-4
-3
-2
-1
-0.2
-0.4
-0.6
-0.8
0.6
2ndderivative
0.4
0.2
0
-5
-4
-3
-2
-1
0
-0.2
-0.4
-0.6
-0.8
Norman Hurd Ricker

developed the Ricker
wavelet while working
for Western Electric (a
US telephone company).
He later applied this
work to the seismic
industry, first at Carter
Oil and later at the
University of Oklahoma.
-1
Chapter 7: Wavelets
16
Minimum-Phase Wavelet
Below is a 30 Hz. minimum phase Ricker Wavelet. Note that the phase
has a linear shift, but the amplitude spectrum is the same as for the zerophase wavelet. Note that the wavelet is not symmetric.
No energy before Zero
Time (causal).
Phase varies
with frequency.
Negative Time
Phase
Positive Time
Amplitude
This type of wavelet is generated from an explosive source such as dynamite or air gun.
Chapter 7: Wavelets
17
Minimum phase: Whats in a name?

Minimum phase really means minimum delay
that is, the wavelet rapidly builds to its maximum
energy, then quickly dies away.
The word phase means different things to different
people and in different contexts. Christopher Liner
wrote a rather coherent summary of possible
meanings in the May 2002 Leading Edge, pp. 456457.
http://scitation.aip.org/getabs/servlet/GetabsServlet?
prog=normal&id=LEEDFF000021000005000456000001&idtype=cvips&gifs=yes
Chapter 7: Wavelets
18
Summing Cosines: Minimum Phase

Each phase
is different!
All phases
are +90.
0
Sum
Minimum-Phase
+90 Phase
Here we see the cosines summed to create the minimum-phase wavelet,

compared to a +90 wavelet.
Chapter 7: Wavelets
19
Rotating the Phase

The phase of a wavelet can be rotated between 0 and 360. Note that in each
case the amplitude spectrum remains the same, but the wavelet shape changes
dramatically. Note where the peak energy is located relative to zero time.
+90 Degrees
Symmetric wavelets
180 Degrees
or Reversed Polarity
270 Degrees
or 90 Degrees
0
Antisymmetric wavelets
0 Degrees
For interpretation and synthetic seismograms, which wavelet is the best?

Chapter 7: Wavelets
20
Changing the Amplitude Spectrum

Each of the wavelets below is zero-phase. Only the amplitude spectra differ. As the
amplitude spectrum becomes broader, the wavelet narrows.
10 Hz
30 Hz
0
Narrow amp
spectrum
20 Hz
40 Hz
0
Broad amp
spectrum
For interpretation and synthetic seismograms which wavelet is the best?

Chapter 7: Wavelets
21
A few words about Polarity

Polarity is related to phase. SEG-Y format includes a header
location in which to specify the polarity, but you, the
interpreter, wont normally see this. Even if someone tells
you that your data are zero phase, should you believe it?
In this school, we follow the polarity convention that a
positive impedance contrast (a soft shale over a hard
limestone, for instance) is shown in a zero-phase display as a
peak (black). This is sometimes called the American
convention.
Many companies follow the opposite convention.
The company that operates a given block usually decides the
phase and polarity.
Even if the phase is claimed to be zero, you should verify!
Sometimes, even within the same office, different polarity
conventions will be in use, depending on the project.
Chapter 7: Wavelets
22
Polarity: A Sad Case History

Consider the following example:
Earth
Model
Interpretation
Assumed Polarity Convention

Observed
Response
Acoustic
Impedance
+
Hard
Hard
Soft
High Porosity Gas Sand
A pretty basic concept, but...

Observed
Response
Hard
Hard
Earth
Model
Interpretation
this happened with a deep marine

exploration well circa 2000.
Actual Polarity Convention
Acoustic
Impedance
Hard
Soft
Hard
Low Porosity Brine Sand
Hard
Soft
Chapter 7: Wavelets
23
Using the Sea Floor to Determine Polarity

The polarity convention can be checked by comparing the sea-floor reflection to the reservoir
section. In general, the sea floor is an increase in impedance and in this deep-water-Nigeria
example, it is displayed as a black peak. In this region, sand is generally low in acoustic impedance
compared to encasing shale. The top of the sand should be a trough, and the base a peak. The
zone of interest appears to contain several low-impedance (possibly sand) events.
Ocean Bottom
Zone of interest
Chapter 7: Wavelets
24
Apparent Phase and Tuning Effects.

What is the Phase?
Tuning effects can cause ambiguity in the seismic response. This wedge model shows the seismic
response as a function of thickness. The input wavelet is zero-phase. At 40-130 ft in thickness, the
model response appears to be minimum-phase or -90 phase. So be careful how and where
phase is determined!
Stack Response Wedge Model
Input Model
Hard
Soft
0 ft
500 ft
Hard
Seismic
Response
Input
Wavelet
Chapter 7: Wavelets
300 ft thick:
Zero-Phase
70 ft thick: appears to be
Minimum or -90 Phase
25
Tuning Thickness
Here is the same wedge model as we saw in the previous slide. At a thickness of
approximately 75 feet, the trough and peak amplitudes reach their maxima. At this
thickness, we say that the soft layer is tuned.
Stack Response Wedge Model

0 ft
Input Wavelet
To first order, tuning in zero-phase data occurs when
the peak of the positive reflection aligns with the sidelobe peak of the negative reflection.
Tuning Thickness =
Vint
4(Dominant Frequency)
Here, Vint = 6000 ft/sec and the dominant frequency is

20 Hz.
Chapter 7: Wavelets
Top
Reflection
Base
Reflection
Tuned
Response
26
Wavelet Summary
A wavelet is the response of seismic energy reflecting
from a rock interface.
We can determine the amplitude spectrum but not
any phase information of a wavelet by autocorrelating seismic data.
To estimate phase information, we need to tie at least
one well to seismic data. SynTool, Jason, Hampson
Russell, and Wavex include tools to do this.
In geophysical reservoir characterization, wavelets are
important for:
Forward modeling
Inversion
Chapter 7: Wavelets
27
Review
Draw a 40 Hz Ricker wavelet in each graph.
Zero Phase
+90 Phase
-180 Phase
-90 Phase
Chapter 7: Wavelets
28
Why should I care about wavelet phase?
Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

AI = 6.60 km/s*g/cc
Vp = 2.8 km/s Vs = 1.4 km/s = 2.1 g/cc
AI = 5.88 km/s*g/cc
Vp = 3 km/s Vs = 1.5 Km/s = 2.2 gm/cc
AI = 6.6 km/s*g/cc
What are the Acoustic Impedances?

What are the Reflection Coefficients?
Convolve these RCs with a
zero-phase wavelet.
Chapter 7: Wavelets
29
Why should I care about wavelet phase?
Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

AI = 6.60 km/s*g/cc
Vp = 2.8 km/s Vs = 1.4 km/s = 2.1 g/cc
AI = 5.88 km/s*g/cc
Vp = 3 km/s Vs = 1.5 Km/s = 2.2 gm/cc
AI = 6.6 km/s*g/cc

90 wavelet.
Chapter 7: Wavelets
30
Does 90 reflectivity look like a log

curve?
Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

AI = 6.60 km/s*g/cc
Vp = 2.8 km/s Vs = 1.4 km/s = 2.1 g/cc
AI = 5.88 km/s*g/cc
Vp = 3 km/s Vs = 1.5 Km/s = 2.2 gm/cc
AI = 6.6 km/s*g/cc
GR

90 wavelet.
Chapter 7: Wavelets
31

Wavelets Lecture - Clean

Uploaded by

Copyright:

Available Formats

Wavelets Lecture - Clean

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Wavelets Lecture - Clean

Uploaded by

Copyright:

Available Formats

What is a wavelet and how can it be described?

What is a wavelet and how can it be described?

How do amplitude, frequency, and phase affect a wave?

How do amplitude, frequency, and phase affect a wave?

Wavelets

You guys arent drilling that hard streak, are

Here the horizontal axis is angle . In future

The top wave has a frequency of 2 Hz.

How would we plot the amplitude spectra

How would we plot the amplitude

The top wave has an amplitude of 1.

A normal cosine wave has its peak amplitude at time 0.

How would we plot the phase

Waves: Amplitude and Phase

Summing Cosine Waves

Amplitude and Phase Spectra

The wavelet is decomposed into the

Summing Cosine Waves

Phase-shifting a cosine wave by 90 is equivalent to a time shift.

The Ricker Wavelet

Norman Hurd Ricker

Minimum phase: Whats in a name?

Summing Cosines: Minimum Phase

Here we see the cosines summed to create the minimum-phase wavelet,

Rotating the Phase

For interpretation and synthetic seismograms, which wavelet is the best?

Changing the Amplitude Spectrum

For interpretation and synthetic seismograms which wavelet is the best?

A few words about Polarity

Polarity: A Sad Case History

Assumed Polarity Convention

A pretty basic concept, but...

this happened with a deep marine

Using the Sea Floor to Determine Polarity

Apparent Phase and Tuning Effects.

Stack Response Wedge Model

Stack Response Wedge Model

Here, Vint = 6000 ft/sec and the dominant frequency is

Why should I care about wavelet phase?

Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

What are the Acoustic Impedances?

Why should I care about wavelet phase?

Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

Convolve these RCs with a

Does 90 reflectivity look like a log

Vp = 3 km/s Vs = 1.5 km/s = 2.2 g/cc

Convolve these RCs with a

You might also like