14.
531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASES IN
SOIL
Point Loads
(P) OF Line
Loads (q/unit length)
TYPES
LOADING
Figure 6.11. Das FGE (2005).
Revised 09/2014
Examples:
- Posts
Figure 6.12. Das FGE (2005).
Examples:
- Railroad track
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASES IN
SOIL
Strip Loads
(q) OF LOADING
Area Loads (q)
TYPES
Examples:
- Exterior Wall Foundations
Revised 09/2014
Examples:
- Column Footings
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASES IN
SOIL
Based
on homogeneous,
weightless, elastic,
isotropic infinitely
ANALYSIS
METHODS:
BOUSSINESQ
large half-space free of initial stress and deformation. The
(1993)
modulus of elasticity is assumed
constant and the principle of
linear superposition is assumed valid (EM1110-1-1904, 1990). Not
accurate for layered soil stratigraphy with substantial thickness
(NAVFAC DM7.01, 1986).
Rigid Surface Layer Over Weaker Underlying Layer: If the surface layer is
the more rigid, it acts as a distributing mat and the vertical stresses in the
underlying soil layer are less than Boussinesq values.
Weaker Surface Layer Over Stronger Underlying Layers: If the surface layer
is less rigid than the underlying layer, then vertical stresses in both layers
exceed the Boussinesq values.
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASES IN
SOIL
Based on the assumption that the soil on which load is applied is reinforced
ANALYSIS
METHODS:
by closely spaced
horizontal layers which
prevent horizontal displacement.
The effect of the Westergaard assumption is to reduce the stresses
substantially belowWESTERGAARD
those obtained by the Boussinesq equations.
VERTICAL STRESS INCREASES IN
SOIL
An approximate stress distribution assumes that the total applied load on
ANALYSIS
METHODS:
2V:1H
the surface
of the soil is distributed
over an area of the same
shape as the
loaded area on the surface, but with dimensions that increase by an
METHOD
amount equal to the depth below
the surface.
Vertical stresses calculated 2V:1H method agree reasonably well with
the Boussinesq method for depths between B and 4B below the
foundation.
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
POINT LOADING (BOUSSINESQ
1883)
3P z
3P
z
z
P
z 2
z
2 L5
2 ( r 2 z 2 )5 / 2
1
P
5/ 2
2 1
2
z
2 r / z 1
Where:
z = Change in Vertical Stress
P = Point Load
Stresses in an Elastic Medium Caused by Point Loading
Figure 6.11. Das FGE (2005).
*Based on homogeneous, elastic, isotropic infinitely large half-space
Revised 09/2014
I1
3
1
2 r / z 2 1 5/2
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
Table 6.1 Variation of I (Das, FGE 2006).
POINT LOADING (BOUSSINESQ 1883)
1
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
3
2
qz
LINE LOADING (BOUSSINESQ
1883)
2
2 2
(x z )
or
Dimensionless
Form
Line Load over the Surface of
a Semi-infinite Soil Mass
Figure 6.12. Das FGE (2005).
*Based on flexible line load of infinite length on a
homogeneous, elastic, isotropic semi-infinite half-space
Revised 09/2014
(q / z)
2
x
z
Where:
= Change in Vertical Stress
q = Load per Unit Length
z = Depth
x = Distance from Line Load
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
Table 6.3 Variation of /(q/z) with x/z (Das, FGE 2006).
LINE LOADING (BOUSSINESQ 1883)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
STRIP LOADING (BOUSSINESQ 1883)
q
sin cos( 2 )
Where:
= Change in Vertical Stress
q = Load per Unit Area
z = Depth
x = Distance from Line Load
Flexible Strip Load over the Surface of
a Semi-infinite Soil Mass
Figure 6.13. Das FGE (2005).
Revised 09/2014
Angles measured in counterclockwise direction are taken
as positive
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
Table
6.4 VariationLOADING
of /q with 2z/B and
2x/B (Das, FGE 2006).
STRIP
(BOUSSINESQ
1883)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
CIRCULAR
LOADING
(BOUSSINESQ
1 1883)
q 1
(R / z) 1
2
3/2
Where:
= Change in Vertical Stress
q = Load per Unit Area
z = Depth
R = Radius
Vertical Stress Below Center of Uniformly Loaded
Flexible Circular Area
Figure 6.15. Das FGE (2005).
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
TableCIRCULAR
6.5 Variation of /q with
z/R (Das, FGE 2006).
LOADING
(BOUSSINESQ
1883)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
3qz ( dxdy)
RECTANGULAR LOADING
d (BOUSSINESQ
2 ( x y z ) qI
1883)
Where:
B
2 5/ 2
y 0 x 0
= Change in Vertical Stress
q = Load per Unit Area
z = Depth
2mn m 2 n 2 1 m 2 n 2 2
2
2
2 2
2
2
1 m n m n 1 m n 1
I2
2
2
4
1 2mn m n 1
tan 2
m n 2 m 2n 2 1
Vertical Stress Below Corner of Uniformly
Loaded Flexible Rectangular Area
Revised 09/2014 Figure 6.16. Das FGE (2005).
B
L
m ;n
z
z
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS
INCREASE ( Z) IN
SOIL
RECTANGULAR
LOADING
(BOUSSINESQ 1883)
Variation of I2 with m and n.
Figure 6.17. Das FGE (2005).
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL
STRESS
INCREASE ( Z)
IN SOIL
RECTANGULAR
LOADING
(WESTERGAAR
Figure 12. NAVFAC
D) DM7.01.
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
Within a
Rectangular Loaded Area:
RECTANGULAR
LOADED AREA
q I 2(1) I 2(2) I 2(3) I 2(4)
Under Center of Footing:
c qI c
I c f (m1, n1 )
Figure 6.18. Das FGE (2005).
Revised 09/2014
L
z
m1 ;n1
B
B
2
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASE ( Z) IN
SOIL
Table 6.6 Variation of I with m and n (Das, FGE 2006).
CENTER OF RECTANGULAR LOADED
AREA
c
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
BOUSSINESQ SOLUTIONS
SUMMARY
(EM 1110-1-1904 TABLE C-1)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
BOUSSINESQ SOLUTIONS
SUMMARY
(EM 1110-1-1904 TABLE C-1)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
BOUSSINESQ SOLUTIONS
SUMMARY
(EM 1110-1-1904 TABLE C-1)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
BOUSSINESQ
GRAPHICAL
SOLUTION
(EM 1110-1-1904
FIGURE 1-2)
Revised 09/2014
STRIP
FOOTING
SQUARE
FOOTING
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
WESTERGAAR
D GRAPHICAL
SOLUTION
(NAVFAC DM7.01 FIGURE
11)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
WESTERGAAR
D GRAPHICAL
SOLUTION
(NAVFAC DM7.01 FIGURE
11)
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
NEWMARK INFLUENCE CHARTS
(BASED ON BOUSSINESQ SOLUTIONS)
STEPS
1. Draw the footing shape to a scale
using Length AB = Depth z.
2. The point under which we look for
v, is placed at the center of the
chart.
3. Count the units and partial units
covered by the foundation (m).
4. v=p=(qo)(m)(I)
I = Influence Factor
Revised 09/2014
14.531 ADVANCED SOIL MECHANICS
Soil Stresses
VERTICAL STRESS INCREASES IN
SOIL
ANALYSIS METHODS: 2V:1H
Q
z
METHOD
( B z )( L z )
Where:
z = Change in Total
Vertical Stress
Q = Applied Foundation
Load
B = Foundation Width
L = Foundation Length
Figure C-1. USACE EM1110-1-1904.
Revised 09/2014
