Scribd
Upload
39 views

Osi Data Link Layer: Network Fundamentals - Chapter 7 Sandra Coleman, CCNA, CCAI

The document discusses the OSI data link layer and its role in data transmission. It describes how the data link layer prepares data for transmission by encapsulating packets into frames and adding header and trailer fields. These frames allow different media access control methods to control how data is placed onto the physical media and transmitted between nodes on a network. Specific MAC techniques like CSMA/CD and token passing are covered, as well how logical network topologies determine the appropriate MAC method to use.

Uploaded by

Ana Marie Suganob
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
39 views

Osi Data Link Layer: Network Fundamentals - Chapter 7 Sandra Coleman, CCNA, CCAI

The document discusses the OSI data link layer and its role in data transmission. It describes how the data link layer prepares data for transmission by encapsulating packets into frames and adding header and trailer fields. These frames allow different media access control methods to control how data is placed onto the physical media and transmitted between nodes on a network. Specific MAC techniques like CSMA/CD and token passing are covered, as well how logical network topologies determine the appropriate MAC method to use.

Uploaded by

Ana Marie Suganob
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 23

OSI DATA LINK LAYER

Network Fundamentals Chapter 7


Sandra Coleman, CCNA, CCAI

Version 4.0

Objectives

Explain the role of Data Link layer protocols in data


transmission.
Describe how the Data Link layer prepares data for transmission
on network media.
Describe the different types of media access control methods.
Identify several common logical network topologies and describe
how the logical topology determines the media access control
method for that network.
Explain the purpose of encapsulating packets into frames to
facilitate media access.
Describe the Layer 2 frame structure and identify generic fields.
Explain the role of key frame header and trailer fields including
addressing, QoS, type of protocol and Frame Check Sequence.

Data Link Layer Accessing the Media


2 basic services
Allows upper layers to access the media
Controls how data is placed onto the media using media access
control and error detection

Data link layer terms


Frame PDU for layer 2
Node device on a network
Media physical means to
carry the signals
Network 2 or more nodes
connected to a common
medium

Data Link Layer Accessing the Media


Function responsible for controlling the transfer of

frames across the media.

Data Link Layer Accessing the Media


The media access control methods may differ from one

media type to another and how devices interact with


that media is all controlled by layer 2.

Formatting data for transmission


Data gets converted into streams of 1s and 0s.
Framing (layer 2 PDU) breaks this stream into

groupings that have control information in the


header/trailer.
These will be discussed in greater detail later.
Typical fields include:
Start/Stop indicator fields mark beginning/end of the frame
Naming/Address fields who sent/receives this frame
Type type of PDU in this fram
Data the actual payload (Layer 3 packet)

Data Link Layer Accessing the Media


It takes hardware & software for all this to work
Layer 2 devices include NICs, Bridges, and Switches

Data-link layer DIVIDED!


Logical Link Control (LLC) defines the software

process that provide services to the network layer


protocols. Places information in the frame that
identifies which protocol is being used (IP, IPX,
Appletalk, etc.).
closest to the Network Layer

Media Access Control (MAC) defines the media

access processes performed by the hardware. Will be


specific to the type of media being used.
closest to the physical layer

Data
Link
Layer

Accessing
the
Media

Data link layer processes are implemented in the NIC


(wired) or PCMCIA (wireless). They comply with the
standards set forth by these parties!

Media Access Control Techniques

Media access control depends on media sharing and the

logical topology.

Compare Media Access Control


Think about vehicles ignoring ALL traffic and entering

roads without regards to other vehicles. MESSY!


Traffic can enter roads using different methods, i.e.
traffic lights, stop signs, yield signs, merging.
You have a different set of rules depending on where
you enter the road.
Likewise, there are different ways to regulate placing
frames on the media. Protocols at layer 2 determine the
rules for access to that media (copper, fiber, wireless,
etc.)

Media Access Control Techniques


Identify two media access control methods for shared

media and the basic characteristics of each

Deterministiccan be
inefficient because a
device has to WAIT for its
turn before it can use the
medium.

Non-deterministicless
overheadTake turnswait
until it hears all clear. Can
cause collisions.

Media Access Control Techniques

Full Duplex Tx/Rx simultaneously (2-way street)


Half Duplex Tx/Rx but only one at a time (1 way

street)

Media Access Control Techniques


Logical topology way a network transfers frames from

one node to the next. This is what the data link layer
sees when controlling media access. These are virtual
connections
Physical topology physical arrangement of the nodes
and connections.
These 2 are not
usually the same!

Media Access Control Techniques


Very simple media access control
Data can only travel to/from 1 other place. No need to

be complicated!

Media Access Control Techniques


Uses CSMA/CD (Ethernet), CSMA/CA (wireless) or

token-passing to transmit data.


Token-passing - passed sequentially. Can only tx when
you have the token.

Media Access Control Techniques


Frames are passed from node to node Token passing!

Ignored if it doesnt belong to them, and passed on.

Media Access Control Addressing and Framing Data


Purpose of encapsulation of data into frames: to

facilitate the entry and exit of data on the media!

Media Access Control Addressing and Framing Data


Start beginning of frame
Source/destination address fields nodes on the network
Type field upper layer service in the frame

Media Access Control Addressing and Framing Data


Layer 2 uses MAC addresses (NIC card). BIA,

hardware, physical, adaptersame thing.


Layer 3 uses IP addresses (logical, network,
hierarchical) that reflect the network on which they
reside.
If a device is MOVED from one subnet to another
layer 2 address is the same. Will need to change the
layer 3 address for the device to communicate.

Media Access Control Addressing and Framing Data


Purpose support any error detection issues
FCS CRC (cyclic redundancy check) value is placed in
the trailers FCS field. Upon arriving at its destination, it is
recalculated and checked to make sure the frame has no
errors.
This calculation occurs at every sending/receiving point in
the route of that frame. (entering & exiting a device)

Traveling frames
As frames traverse the network, the source and

destination addresses may change.


Source MAC gets reset to the next device (routers) as it
travels
Destination MAC gets set to the next device in line
(router or pc)
Source IP NEVER CHANGES
Destination IP NEVER CHANGES

Thats all for Ch. 7


Study Guide: NONE
Online Ch. 7 Test
MW class - By Sunday Sept. 16, 2012 - midnight
T/Th class By Sunday Sept. 9, 2012 - midnight
Ch. 7 Test
MW class Mon 9/17/2012
T/TH class - Tues 9/11/2012
Lecture for Ch. 6 will begin after

You might also like