Scribd
Upload
134 views

Home Automation Control System Using DTMF

This document describes a home automation control system using dual-tone multi-frequency (DTMF) signaling. The system allows a user to control electrical loads like lamps and appliances remotely using a DTMF-enabled phone. It works by detecting DTMF tones sent by the user and using a microcontroller to operate relays connected to loads. The system can control up to 8 devices and provides features like password protection and status checking via an LCD interface. It requires minimal components and allows remote control of home automation without distance limitations.

Uploaded by

engaydi
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
134 views

Home Automation Control System Using DTMF

This document describes a home automation control system using dual-tone multi-frequency (DTMF) signaling. The system allows a user to control electrical loads like lamps and appliances remotely using a DTMF-enabled phone. It works by detecting DTMF tones sent by the user and using a microcontroller to operate relays connected to loads. The system can control up to 8 devices and provides features like password protection and status checking via an LCD interface. It requires minimal components and allows remote control of home automation without distance limitations.

Uploaded by

engaydi
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 25

HOME AUTOMATION CONTROL SYSTEM USING DTMF

BY
JIGAR M PATEL
DHARMESH G PATEL

INDEX
Introduction
What is DTMF ?
Block Diagram
System Working
Circuit Diagram
ICs Used
Applications
Merits & Demerits
Features of TCS
Future Expansion

INTRODUCTION
One

can access this unit even when


he/she is not present at the place
where the system is installed.
Any
(DTMF) telephone set or handheld tone dialer may be used to send
commands to the switching unit.
The
switching unit is capable of
controlling mains, powered loads with
the aid of commands received via a
telephone.

WHAT IS DTMF ?
Dual

tone multiple frequency signaling


(DTMF).
Multiple-frequency signaling consists of a
combination
of
two
tones
with
frequencies within the speech band.
Each combination of two frequencies
representing a single digit.
The tones are in two groups : 1 Low Band
2 High
Band

DTMF
(DUAL TONE MULTIPLE FREQUENCY
SIGNALING)

Low

697 HZ
770 HZ
852 HZ
941 HZ

1209 HZ
1
4
7
*

High
1336 HZ 1447 HZ
2
3
5
6
8
9
0
#

1633 HZ
A
B
C
D

BLOCK DIAGRAM

SYSTEM WORKING
Dial

your number using DTMF phone or


Cell phone from anywhere in the world.
The
MCU on the interface senses
Telephone ring, Automatic telephone
pick up, and line hang up, displays
information on a 16x2 LCD module and
controls the relay switching.
After a six rings the circuit lifts the
receiver and sends an acknowledgement
tone to signal to the caller that a sixdigit password number is to be entered.

Enter the password.

When the password has been incorrectly entered four times in


a row, the interface an error sound is produced and the
receiver replaced on-hook this function thwarts any attempt
by 'hackers' to quickly try a large number of codes in a
sequence.

If password is correct enter in to the main menu .

Main menu : Enter Command


* < 1 8 > * - operate one of the four relays 1 to 8.
# < 1 8 > # - release one of the four relays 1 to
8.
123 Read EPROM
456 Change password
789 Read relay status
* 0 # - Line disconnected

CIRCUIT DIAGRAM
LCD interface

EEPROM interface
Microcontroller interface

Acknowledgement tone output

Ring detector

Regulated power supply

DTMF decorder interface

RELAY DRIVER CIRCUIT

MICROCONTROLLER UNIT
WORKS
To

count the pre-programmed number


of ringing signals.
To enable the high value resistance
after counting the pulses.
To accept the decoded tones send by
the tone decoder.
To operate the corresponding relays
according to the signals.

ICS USED
AT89CXXX

Microcontroller

AT89C51 is a low-power, high-performance


CMOS 8-bit microcomputer with 4K bytes of
Flash programmable and erasable read only
memory (PEROM).

LM 7805
Used to make the stable voltage of +5v
for Microcontroller .

MT 8870 (DTMF DECORDER)

Complete DTMF receiver integrating both the band


split filter and digital decoder functions.

Decoder uses digital counting techniques to detect


and decode all 16 DTMF tone pairs into a 4-bit code.

MC T2E/4N35 (RING DETECTOR)


It is used for ring detection .
MCT2E series opt isolators consist of a gallium
arsenide
infrared emitting Diode driving a silicon photo
transistor
in a 6-pin dual in line package.

FLASH EEPROM AT24C04


AT24C04 are 4K bit electrically erasable programmable
memories , Organize as 2 blocks of 256 * 8 bits.
They are manufactured in SGS-THOMSONs HiEndurance
Advanced CMOS technology .

LCD MODULE (16X2 LINE LCD)

SPDT RELAY 12V


It is used for switching (Turn ON/OFF) the device
connected to it.

APPLICATIONS
Wide

range of applications in various

fields
Household applications
Industrial applications
Office applications
Institutional applications
Telephone answering machine
Interactive voice response
system(IVRS)

MERITS
No distance
limitation.
Instant switching
without any delay.
Use less components
and power
consumption is low.
Its cost is very less.
It cannot be misused
unless any other
person knows the
code.

&

DEMERITS

The unit cannot be


accessed when the
phone is dead.
It is only used on
phones having DTMF
dialing facilities.
The wiring becomes
complex and costly.

FEATURES OF TCS

Easy availability : The components is used in


the circuit are easily available in the market.

Flexibility : micro-controller offers lot of


flexibility to the programmer for the
programming purpose.

Compatibility : This switching unit


compatible with any kind of telephone set.

Versatileness : you can access and even


connect desired no. of loads to it.

is

Longer
Less

period of service

experience : The PCB uses circuits

that are very cheap. They are easily


accessible as their voltage & power
requirement is less.
Compactness

: The unit is much more

compact as the PCB is reduced to almost one


fourth of the original PCB.

FUTURE EXPANSION

Increasing no. of channels:


This circuit provides a facility for 8 channels.
So we can individually access each appliance
to one channel.
If this is not desired then by the use of
multiplexers and modification in the software
and using the remaining ports we increase
the no. of channels.

You might also like