Scribd
Upload
339 views

Unit V Cooling System

The document discusses the cooling system of an internal combustion (IC) engine. It provides reasons for needing a cooling system such as preventing melting of engine materials from high combustion temperatures. There are two main types of cooling systems - air cooling and liquid cooling. A liquid cooling system circulates coolant around the engine to absorb heat and transfer it to a radiator to cool the coolant so it can absorb more heat. Key components of a liquid cooling system include the water pump, radiator, thermostat, hoses, and pressure cap.

Uploaded by

Ravindra_1202
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
339 views

Unit V Cooling System

The document discusses the cooling system of an internal combustion (IC) engine. It provides reasons for needing a cooling system such as preventing melting of engine materials from high combustion temperatures. There are two main types of cooling systems - air cooling and liquid cooling. A liquid cooling system circulates coolant around the engine to absorb heat and transfer it to a radiator to cool the coolant so it can absorb more heat. Key components of a liquid cooling system include the water pump, radiator, thermostat, hoses, and pressure cap.

Uploaded by

Ravindra_1202
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 20

Applied Thermodynamics

UNIT V
I.C. Engine Systems

IC Engine Cooling System


The cooling system is provided in the IC engine for the
following reasons:

The temperature of the burning gases in the engine cylinder


reaches up to 1500 to 2000C, which is above the melting
point of the material of the cylinder body and head of the
engine. (Platinum, a metal which has one of the highest
melting points, melts at 1750C, iron at 1530C and
aluminium at 657C.) Therefore, if the heat is not dissipated,
it would result in the failure of the cylinder material.
Due to very high temperatures, the film of the lubricating
oil will get oxidized, thus producing carbon deposits on
the surface. This will result in piston seizure.

IC Engine Cooling System


The cooling system is provided in the IC engine for the
following reasons:

Due to overheating, large temperature differences


may lead to a distortion of the engine components
due to the thermal stresses set up. This makes it
necessary for, the temperature variation to be kept
to a minimum.
Higher temperatures also lower the volumetric
efficiency of the engine.

REQUIREMENTS OF EFFICIENT
COOLING SYSTEM
The two main requirements of an efficient
cooling system are:
1. It must be capable of removing only about 30% of
the heat generated in the combustion chamber. Too
much removal of heat lowers the thermal efficiency
of the engine.
2. It should remove heat at a fast rate when the engine
is hot. During the starting of the engine, the cooling
should be very slow so that the different working
parts reach their operating temperatures in a short
time.

TYPES OF COOLING SYSTEM


There are two types of cooling systems:
(i)Air cooling system and
ii) Water-cooling system.

Cooling System
Get the engine up to optimum operating Temperature as quickly as
possible and maintains it at that temperature.
Controls the heat produced in combustion chamber, so that the engine parts
are not damaged & the oil does not break down.

Cooling System
TOTAL FUEL BURNED
1/3 cooling system

1/3 Exhaust system

1/3 Propels the vehicle

Cooling System
AIR COOLED
Have metal FINS on the outer perimeter
of the engine.

Heat is transferred from the engine,


through these fins, into the atmosphere.

Cooling System
LIQUID COOLED
A liquid (coolant) is circulated around the cylinders and absorb heat from the
cylinder walls and cylinder head.
COOLANT is a mixture of antifreeze (Ethylene Glycol) and
Water (some Aluminum radiators have special antifreeze)
Coolant absorbs heat as it passes through the engine and also
lubricates the water pump.
Hot coolant enters the radiator in which the heat
is passed on to air that is flowing
through the radiator.
Prevents rust and corrosion from the water jackets.
Cooling system flush is recommended every two years
in order to remove any rust or contaminants.

Cooling System
Water Jackets
Designed to keep engine block and cylinder head
cool.
Open spaces between the outside of cylinder and
inside of cylinder block and head.
When engine is running at normal operating
temperature, the coolant is forced through the
water jackets in the engine block, through the
head gasket, into the head, and back to the
radiator.
Cylinder head gasket sits between the short block and cylinder head.
If damaged, the coolant enters the combustion chamber and
the combustion into the cooling system. It will allow acids to form.
(WHITE SMOKE)

Cooling System
Water Pump (Impeller Type)
Draws the coolant from the radiator,
through the lower radiator hose, and
then forces it through the water jackets,
back into the radiator.
If the clutch fan can be wiggled up and
down, most likely the water pump needs
to be replaced.

Water pumps gasket is placed between


the water pump and the engine block to
prevent leakage 9if left loose it might leak
and if tightened too much it might crack).

Cooling System
Water pump is driven by the crankshaft through
Timing Belt (Keeps Cam and Crank shafts in time)
Drive/accessory Belt (Runs alternator, power-steering
pump, AC, etc.)

V-Belt

Serpentine Belt

Cooling System
Engine Fan draws air through the radiator at low speeds (i.e. Traffic)

Clutch fan is mounted on the water pump and


is driven by the drive belt.

It slips at higher speed, in turn slowing the fan


speed down.
It locks up at slow speeds, in turn speeding
up the fan RPMs.
Should be able to turn when the engine is turned off.

Cooling System
Electric fan is mounted on the radiator
and is operated by battery power.

Is controlled by the thermostat switch.


Is located on Thermostat housing, Block, or Radiator.
Some modern cars have the range between
193 to 207 F (89 to 97 C)
On AC equipped cars, a second fan is mounted,
and it runs any time AC is turned on.

CAUTION Electric fan may run while the


engine is turned off.

Cooling System
Radiator is a heat exchanger that removes heat from the coolant passing
through it.
Vertical or Horizontal core

Vehicles equipped with automatic transmission


have transmission cooler build into the radiator.

Some vehicles (towing purposes) have oil cooler


mounted to or build into the radiator.

Cooling System
Thermostat placed between the cylinder head and top radiator hose.
Purpose is to close off this passage when engine is cold.

The temperature that the thermostat opens is


called thermostat rating.
Higher temperature
thermostats are used
on the modern vehicles.

If thermostat is stuck open the engine will run cool,


and if the thermostat is stuck closed the engine will
Overheat.
Can be checked by placing in the boiling water.

Cooling System
Radiator Pressure cap seals the cooling
system and pressurize it.
Most caps insert 12-16 lbs of pressure.
Each pound of pressure inserted increases the boiling
point of coolant by 1.8 C (3 F).
Boiling point of water is 100 C (212 F).
Has a built in pressure relief valve to prevent excessive pressure build-up.
Has a vacuum vent valve (when engine is shut off and it cools, the coolant volume
is reduced)
Excess coolant goes to the expansion tank.
CAUTION never open the radiator cap if you
cant squeeze the top radiator hose.

Cooling System
Hoses
Top Radiator hose brings the coolant back to the radiator and are molded
Specifically for individual make and model.

Lower radiator hose draws the coolant into the


engine, from the radiator and is attached to the
water pump. (sometimes a spring is inserted in
order to prevent collapsing)

Cooling System
BLOCK HEATER
Fitted into the block to keep the engine
warm during extremely cold weather.
(Diesel Engines)

FREEZE PLUG
Prevents engine block cracking
if water freezes inside.

Common cause of freeze plug failure is


rust.

Cooling System

You might also like