STEAM POWER

PLANT

STEAM POWER
The PLANT
Principle of Heat Engine and the Second
Law of Thermodynamics
Carnot Cylce
Rankine Cycle
Perfomance Criteria of a Steam Power Plant
Rankine Cycle with Superheated Steam
Rankine Cycle with Reheating and
Regeneration

Objectives
1.Analyse vapor power cycles in which the
working fluid is alternately vaporized and
condensed.
2.Investigate ways to modify the basic
Rankine vapor power cycle to increase the
cycle thermal efficiency.
3.Analyse the reheat and regenerative vapor
power cycles.
4.Review power cycles that consist of two
separate cycles, known as combined
3
cycles.

Thermal Power
Plant

Sub-Systems in a Steam
Power Plant
Our focus will be on subsystem A.

SUB-SYSTEM A

Introduction
Steam (Water Vapor)
Steam is the most common working fluid used in vapor
power cycles because of its many desirable
characteristics, such as: (a) low cost, (b) availability, and
(c) high enthalpy of vaporization#.
Steam power plants are commonly referred to as: (a)
coal plants, (b) nuclear plants, or (c) natural gas plants,
depending on the type of fuel used to supply heat to
the steam.
The steam goes through the same basic cycle in all of
them. Therefore, all can be analyzed in the same
# The amount of energy needed to vaporize a unit mass of
manner.
7
saturated liquid at a given temperature or pressure, hfg.

BASIC STEAM POWER

PLANT

Carnot Vapor Cycle

Carnot cycle is the most efficient power cycle operating between
two specified temperature limits (Figure).
We can adopt the Carnot cycle first as a prospective ideal cycle for
vapor power plants.

Sequence of Processes:

1-2 Reversible and isothermal

heating (in a boiler);
2-3 Isentropic expansion (in a
turbine);
3-4 Reversible and isothermal
condensation (in a
condenser); and
4-1 Isentropic compression (in a
compressor).
9

Problem Carnot
Cycle
10-3
Consider a steady-flow Carnot cycle which

uses water as the working fluid. Water changes

from saturated liquid to saturated vapor as heat
is transferred to it from a source at 250C. Heat
rejection takes place at a pressure of 20 kPa.
Show the cycle on a T-s diagram relative to the
saturation lines, and determine
(a)the thermal efficiency,
(b)the amount of heat rejected, in kJ/kg, and
(c)the net work output.
10

Answers: (a)36.3%, (b) 1092.3 kJ/kg, (c) 623

Is Carnot Cycle
Practical?

The Carnot cycle is NOT a suitable

model for actual power cycles
because of several impracticalities
associated with it:
Process 1-2
Limiting the heat transfer processes to
two-phase systems severely limits
the maximum temperature that can
be used in the cycle (374C for water).
Process 2-3
The turbine cannot handle steam with
a high moisture content because of
the impingement of liquid droplets on
the turbine blades causing erosion
and wear.
Process 4-1
It is not practical to design a

11

The Rankine Cycle

Many of the impracticalities
associated with the Carnot cycle
can be eliminated by:
(a)
superheating the steam
in the
boiler,
(b)
condensing the steam
completely
in
the
condenser.
The modified Carnot cycle is
called the Rankine cycle, which
is the ideal and practical cycle
for vapor power plants (Figure).
This ideal cycle does not involve

12

Sequence
Processes

of

The ideal Rankine cycle

consists of four processes:
1-2 Isentropic
compression in a water
pump;
2-3 Constant pressure
heat addition in a boiler;
3-4 Isentropic
expansion in a turbine;
4-1 Constant pressure
heat rejection in a
condenser.
13

Energy Analysis of Ideal Rankine

The pump, boiler, turbine, and condenser are steady-flow devices.
Thus all four processes that make up the ideal Rankine cycle can be
analyzed as steady-flow processes.
The kinetic and potential energy changes of the steam are usually
small. Thus the Steady-flow Energy Equation per unit mass of
steam reduces to:

Energy Interactions
The boiler and condenser do not
involve any work but both involve
with heat interactions.
14
The pump and the turbine are

Energy Interactions in Each Devic

Pump: The work needed to operate the
water pump,
where,

Boiler:
supplied in

The amount of heat

the steam boiler,

Turbine:
The amount of work
produced by the turbine,

Condenser: The amount of heat

rejected to cooling medium in
the
condenser,
15

Performance of Ideal Rankine C

Thermal Efficiency
The thermal efficiency of the Rankine
cycle is determined from,

where the net work output,

Note: +ve quantities only!

Thermal efficiency of Rankine cycle

can also be interpreted as the ratio
of the area enclosed by the cycle
on a T-s diagram to the area under
the heat-addition process.

Performance of Ideal Rankine C

Back Work Ratio (BWR)
The back work ratio (bwr) of the Rankine
cycle is determined from,

Note: +ve quantities only!

Problem - The Simple Rankine

Cycle

1015
A steam power plant operates on a simple
ideal Rankine cycle between the pressure
limits of 3 MPa and 30 kPa. The temperature of
the steam at the turbine inlet is 700C, and
the mass flow rate of steam through the cycle
is 50 kg/s. Show the cycle on a T-s diagram
with respect to saturation lines, and determine
(a)the thermal efficiency of the cycle and
(b)the net power output of the power plant
(c)The back work ratio (bwr)
18

Problem - The Simple Rankine

Cycle

1014
Consider a 210-MW steam power plant that
operates on a simple ideal Rankine cycle.
Steam enters the turbine at 10 MPa and 500C
and is cooled in the condenser at a pressure of
10 kPa. Show the cycle on a T-s diagram with
respect to saturation lines, and determine:
(a)the quality of the steam at the turbine exit,
(b)the thermal efficiency of the cycle, and
(c)the mass flow rate of the steam.
Answers: (a) 0.793, (b) 40.2 percent, (c) 165
19
kg/s

Problem - The Simple Rankine

Cycle
10-20
Consider a coal-fired steam power plant

that
produces 300 MW of electric power. The power plant
operates on a simple ideal Rankine cycle with turbine
inlet conditions of 5 MPa and 450C and a condenser
pressure of 25 kPa. The coal has a heating value (energy
released when the fuel is burned) of 29,300 kJ/kg.
Assuming that 75 per cent of this energy is transferred
to the steam in the boiler and that the electric generator
has an efficiency of 96 per cent, determine
(a)the overall plant efficiency (the ratio of net electric
power output to the energy input as fuel) and
(b)the required rate of coal supply.
Answers: (a) 24.5 per cent, (b) 150 t/h

Actual Vapor Power

Cycles

The actual vapor power cycle differs from the ideal Rankine cycle as
a result of irreversibilities in various components. Two common
sources of irreversibilities are:
(a)fluid friction, and
(b)heat
loss to the surroundings.
Fluid friction causes pressure
drops in the boiler, condenser,
and the piping between various
components. Water must be
pumped to a higher pressure requires a larger pump and larger
work input.
More
heat
needs
to
be

transferred to the steam in the

boiler to compensate for the
undesired heat losses from the
steam to the surroundings.
As a result, the cycle thermal
efficiency decreases.

Isentropic
A pump requires a greater work input, and a turbine produces a
Efficiencies
smaller
work output as a result of irreversibilities.
The deviation of actual pumps and turbines from the isentropic ones
can be accounted for by utilizing isentropic efficiencies, defined
as,
Pump:

Turbine:
In actual condensers, the liquid is
usually
sub-cooled to prevent the
onset of cavitation, which may damage
the water pump. Additional losses occur
at the bearings between the moving
parts as a result of friction. Two other
factors are the steam that leaks out

22

Problem - The Simple Rankine

Cycle
10-23
Consider a steam power plant that operates

on a simple Rankine cycle and has a net power

output of 45 MW. Steam enters the turbine at 7 MPa
and 500C and is cooled in the condenser at a
pressure of 10 kPa by running cooling water from a
lake through the tubes of the condenser at a rate of
2000 kg/s. Assuming an isentropic efficiency of 87
per cent for both the turbine and the pump. Show
the cycle on a T-s diagram with respect to
saturation lines, and determine
(a)the thermal efficiency of the cycle,
(b)the mass flow rate of the steam, and
(c)the temperature rise of the cooling water.

Increasing Efficiency of
Thermal
efficiency ofCycle
the ideal Rankine cycle can be increased by:
Rankine
(a)Increasing the average temperature at which heat is transferred
to the working fluid in the boiler, or
(b)decreasing the average temperature at which heat is rejected
from the working fluid in the condenser.

Lowering the Condenser Pressure

The condensers of steam power plants
usually operate well below the
atmospheric pressure. There is a lower
limit to this pressure depending on the
temperature of the cooling medium.
Side effect: Lowering the condenser
pressure increases the moisture
content of the steam at the final
stages of the turbine can cause
blade damage, decreasing isentropic

24

Increasing Efficiency of
Rankine Cycle

Superheating the Steam to High

Temperatures
Superheating the steam

increases both
the net work output and heat input to
the cycle. The overall effect is an
increase in thermal efficiency of the
cycle.
Superheating to higher temperatures will
decrease the moisture content of the
steam at the turbine exit, which is
desirable avoid erosion of turbine
blades.
The superheating temperature is limited
by
metallurgical
considerations.
Presently
the
highest
steam
temperature allowed at the turbine inlet
is about 620C.
25

Increasing Efficiency of
Rankine Cycle
Increasing the Boiler Pressure

Increasing the boiler pressure raises

the average temperature at which
heat is transferred to the steam.
This, in turns increases the thermal
efficiency of the cycle.
Note:
For a fixed turbine inlet temperature,
the cycle shifts to the left and the
moisture content of steam at the
turbine exit increases.
This side effect can be corrected by
reheating the steam.
26

Problem Increase the efficiency of the

Rankine Cycle

Consider a steam power plant operating on the

ideal Rankine cycle. Steam enters the turbine at
4 MPa and 350C and is condensed in the
condenser at a pressure of 10 kPa. Determine
(a)the thermal efficiency of this power plant,
(b)the thermal efficiency if steam is superheated
to 650C instead of 350C, and
(c)the thermal efficiency if the boiler pressure is
raised to 15 MPa while the turbine inlet
temperature is 600C.
27

The Ideal Reheat Rankine Cycle

Reheating is a practical solution to the excessive moisture
problem in turbines, and it is commonly used in modern steam
power plants. This is done by expanding the steam in two-stage
turbine, and reheat the steam in between the stages.

Note: Incorporation of the single reheat in a modern power plant improves

28
the cycle efficiency by 4 ~ 5 percent.

The Ideal Reheat Rankine Cycle

With a single reheating process, the total heat
input and the total turbine work output for
the ideal cycle become,

29

Problem - The Reheat Rankine

Cycle
10-38 A steam power plant operates on an ideal
reheat Rankine cycle between the pressure limits
of 15 MPa and 10 kPa. The mass flow rate of
steam through the cycle is 12 kg/s. Steam enters
both stages of the turbine at 500C. If the
moisture content of the steam at the exit of the
low-pressure turbine is not to exceed 10 per
cent, show the cycle on a T-s diagram with
respect to saturation lines. Determine,
(a)the pressure at which reheating takes place,
(b)the total rate of heat input in the boiler, and

Problem - The Reheat Rankine

Cycle
10-39 A steam power plant operates on the reheat
Rankine cycle. Steam enters the high-pressure turbine
at 12.5 MPa and 550C at a rate of 7.7 kg/s and leaves at
2 MPa. Steam is then reheated at constant pressure to
450C before it expands in the low-pressure turbine. The
isentropic efficiencies of the turbine and the pump are 85
percent and 90 percent, respectively. Steam leaves the
condenser as a saturated liquid at a pressure of 9.73kPa.
If the moisture content of the steam at the exit of the
turbine is not to exceed 5 percent, determine:
(a)the net power output, and
(b)the thermal efficiency.
Answers: (a) 10.2 MW, (b) 36.9 percent.

31

Assignment 1 - The Simple Rankine

Consider a steam powerCycle
plant that operates on a reheat
Rankine cycle and has a net power output of 80 MW.
Steam enters the high-pressure turbine at 10 MPa and
500C and the low-pressure turbine at 1 MPa and 500C.
Steam leaves the condenser as a saturated liquid at a
pressure of 10 kPa. The isentropic efficiency of the
turbine is 80 per cent, and that of the pump is 95 per
cent. Show the cycle on a T-s diagram with respect to
saturation lines, and determine
(a)the quality (or temperature, if superheated) of the
steam at the turbine exit,
(b)the thermal efficiency of the cycle, and
(c)the mass flow rate of the steam.

The Ideal Regenerative Rankine

Heat is transferred to the working fluid during process 22 at a relatively low temperature (Figure). This lowers
the average heat-addition temperature and thus the
cycle efficiency.
Regeneration Process
Steam is extracted from the
turbine at various points, and is
used to heat the feedwater,
before it enters the boiler. The
device where the feedwater is
heated using the steam is called
a regenerator, or a feedwater
heater (FWH).
A feedwater heater is a heat
exchanger
where
heat
is
transferred from the extracted
steam to the feedwater either by:
33
(a) mixing the two fluid streams
(open FWH) or (b) without

The Ideal Regenerative Rankine

Open Feedwater Heaters
An open FWH is a mixing chamber, where the steam
extracted from the turbine (state 6) mixes with the feedwater
exiting the pump (state 2). Ideally, the mixture leaves the
heater as a saturated liquid (state 3) at the FWHs pressure.

y
1-y

34

The Ideal Regenerative Rankine

Energy Analyses
The heat and work interactions in a regenerative Rankine cycle
with one feedwater heater can be expressed (per unit mass of
steam flowing through the boiler), as follows:

Mass fraction of steam

extracted from the turbine,
Pump work input,

Mass
of
Steam
Extracted
For each 1 kg of steam
leaving the boiler, y kg
expands partially in the
turbine and is extracted
at state 6.
The remaining (1-y) kg of
the steam expands to the
condenser pressure.
Therefore, the mass flow
35be
rates of the steam will

Note: The cycle efficiency increases further as the number of feedwater

The Ideal Regenerative

Rankine Cycle
6

36

Problem-The Regenerative
Rankine
Cycle
A steam power plant operates on an ideal regenerative Rankine
cycle. Steam enters the turbine at 6 MPa and 450C and is
condensed in the condenser at 20 kPa. Steam is extracted from the
turbine at 0.4 MPa to heat the feedwater in an open feedwater
heater. Water leaves the feedwater heater as a saturated liquid.
Show the cycle on a T-s diagram, and determine:
(a) the net work output per kg of steam flowing through the
boiler, and
(b) the thermal efficiency of the cycle.
Answers: (a) 1017 kJ/kg, (b) 37.8 percent

37

The Ideal Regenerative

Rankine
Cycle
Closed
Feedwater
Heater

In a closed feedwater heater, heat is transferred from the extracted

steam (state 7) to the feedwater leaving the pump (state 2) without
mixing. The two streams can be at different pressures (P 7 P2). The
condensate (state 3) is pumped into a mixing chamber to mixed with
the heated feedwater (stateIdeally,
9).
T 9 T3

38

Problem-The Regenerative
Rankine
Cycle
A steam power plant operates on an ideal regenerative
Rankine cycle. Steam enters the turbine at 6 MPa and
450C and is condensed in the condenser at 20 kPa.
Steam is extracted from the turbine at 0.4 MPa to heat
the feedwater in closed feedwater heater. Assume that
the feedwater leaves the heater at the condensation
temperature of the extracted steam and that the
extracted steam leaves the heater as a saturated liquid
and is pumped to the line carrying the feedwater.
Show the cycle on a T-s diagram, and determine:
(a)
the net work output per kg of steam flowing
through the
boiler, and
39
(b)
the thermal efficiency of the cycle.

Open & Closed FWH Combin

Most steam power plants use a combination of open and closed
feedwater heaters.

40

Open vs. Closed Feedwater H

Open FWHs
Open feedwater heaters are simple and inexpensive.
They have good heat transfer characteristics.
For each feedwater heater used, additional feedwater
pump is required.
Closed FWHs
The closed feedwater heaters are more complex
because of the internal tubing network. Thus they are
more expensive.
Heat transfer in closed feedwater heaters is less
effective since the two streams are not allowed to be in
direct contact.
The closed feedwater heaters do not require41 a

Problem-The Reheat-Regenerative
Rankine Cycle
A steam power plant operates on an ideal reheatregenerative Rankine cycle and has a net power output
of 80 MW. Steam enters the high-pressure turbine at 10
MPa and 550C and leaves at 0.8 MPa. Some steam is
extracted at this pressure to heat the feedwater in an
open feedwater heater. The rest of the steam is
reheated to 500C and is expanded in the low-pressure
turbine to the condenser pressure of 10 kPa.
Show the cycle on a T-s diagram and determine:
(a) the mass flow rate of steam through the boiler,
and
(b) thermal efficiency of the cycle.
42

Example: Reheat-Regenerative Rankine

Cycle

43

Example: Combination of open and closed

FWH

44