1 Siteinvestigation

SITE INVESTIGATION
Definition
The process of determining the layers of
natural soil deposits that will underlie a
proposed structure and their physical
properties is generally referred to as
site investigation.
The purpose of a soil

investigation program
1. Selection of the type and the depth of foundation suitable
for a given structure.
2. Evaluation of the load-bearing capacity of the foundation.
3. Estimation of the probable settlement of a structure.
4. Determination of potential foundation problems (for
example, expansive soil, collapsible soil, sanitary landfill,
etc.)
5. Establishment of ground water table.
6. Prediction of lateral earth pressure for structures like
retaining walls, sheet pile bulkheads, and braced cuts.
7. Establishment of construction methods for changing subsoil
conditions.
3
EXPLORATION PROGRAM
The purpose of the exploration program is to
determine, within practical limits, the stratification
and engineering properties of the soils underlying
the site.
The principal properties of interest will be the
strength, deformation, and hydraulic
characteristics. The program should be planned so
that the maximum amount of information can be
obtained at minimum cost.
4
Steps of subsurface
exploration program [Stage
1]
1.Assembly of all available information on
dimensions, column spacing, type and
use of the structure, basement
requirements, and any special
architectural considerations of the
proposed building. Foundation
regulations in the local building code
should be consulted for any special
requirements.
Steps of subsurface
2]
2.Reconnaissance of the area:
This may be in the form of a field trip to
the site which can reveal information on
the type and behavior of adjacent
structures such as cracks, noticeable
sags, and possibly sticking doors and
windows. The type of local existing
structure may influence, the exploration
program and the best foundation type
for the proposed adjacent structure.
6
Steps of subsurface
3]preliminary site investigation:
3.A
In this phase a few borings are made or a test pit
is opened to establish in a general manner the
stratification, types of soil to be expected, and
possibly the location of the groundwater table.
One or more borings should be taken to rock, or
competent strata, if the initial borings indicate
the upper soil is loose or highly compressible.
This amount of exploration is usually the extent
of the site investigation for small structures.
Steps of subsurface
4]detailed site investigation:
4.A
Where the preliminary site investigation
has established the feasibility of the
project, a more detailed exploration
program is undertaken. The preliminary
borings and data are used as a basis for
locating additional borings, which should
be confirmatory in nature, and determining
the additional samples required.
8
Depth of Boring
The approximate required minimum
depth of the borings should be
predetermined. The estimated depths can
be changed during the drilling operation,
depending on the subsoil encountered.
To determine the approximate minimum
depth of boring, engineers may use the
following rule:
9
Depth of Boring
1. Determine the net increase of stress, under a
foundation with depth as shown in the Figure.
2. Estimate the variation of the vertical effective
stress, ', with depth.
3. Determine the depth, D = D1, at which the stress
increase is equal to (1/10) q (q = estimated net
stress on the foundation).
4. Determine the depth, D = D2, at which /' = 0.05.
5. Unless bedrock is encountered, the smaller of the
two depths, D1 and D2, just determined is the
approximate minimum depth of boring required.
Table shows the minimum depths of borings for
buildings based on the preceding rule.
10
Depth of Boring
Determination of the minimum depth of boring

11
Depth of Boring
Depth of Boring
12
Depth of Boring
For hospitals and office buildings, the following
rule could be use to determine boring depth
13
Depth of Boring
When deep excavations are anticipated,
the depth of boring should be at, least
1.5 times the depth of excavation.
Sometimes subsoil conditions are such
that the foundation load may have to be
transmitted to the bedrock. The minimum
depth of core boring into the bedrock is
about 3m. If the bedrock is irregular or
weathered, the core borings may have to
be extended to greater depths.
14
Spacing Boring
There are no hard and fast rules for the
spacing of the boreholes. The following
table gives some general guidelines for
borehole spacing. These spacing can
be increased or decreased, depending
on the subsoil condition. If various soil
strata are more or less uniform and
predictable, the number of boreholes
can be reduced.
15
Spacing Boring
Approximate Spacing of Boreholes
16
SOIL BORING
The earliest method of obtaining a test hole
was to excavate a test pit using a pick and
shovel. Because of economics, the current
procedure is to use power-excavation
equipment such as a backhoe to excavate the
pit and then to use hand tools to remove a
block sample or shape the site for in situ
testing. This is the best method at present for
obtaining quality undisturbed samples or
samples for testing at other than vertical
orientation.
17
SOIL BORING
18
Boring tools
Auger boring
Power drills
19
Boring tools
20
Boring tools
21
Boring
tools
22
Preparation of Boring Logs

1.
2.
3.
4.
5.
6.
Name and address of the drilling company

Drillers name
Job description and number
Number, type, and location of boring
Date of boring
Subsurface stratification, which can he obtained by visual
observation of the soil brought out by auger, split-spoon
sampler, and thin-walled Shelby tube sampler
7. Elevation of water table and date observed, use of casing
and mud losses, and so on
8. Standard penetration resistance and the depth of SPT
9. Number, type, and depth of soil sample collected
10. In case of rock coring, type of core barrel used and, for
each run, the actual length of coring, length of core
recovery, and ROD
23
24
SOIL SAMPLING
Two types of soil samples can be obtained during
sampling disturbed and undisturbed.
The most important engineering properties required for
foundation design are strength, compressibility, and
permeability.
Reasonably good estimates of these properties for
cohesive soils can be made by laboratory tests on
undisturbed samples which can be obtained with
moderate difficulty. It is nearly impossible to obtain a
truly undisturbed sample of soil; so in general usage
the term "undisturbed" means a sample where some
precautions have been taken to minimize disturbance
or remolding effects.
25
Disturbed vs Undisturbed
Good quality samples
necessary.
AAR<10
R<10
%
%
soil
O.D.2 I .D.2
AR
100 (%)
2
I .D.
area
arearatio
ratio
sampling tube
Thicker the wall, greater the

disturbance.
26
Disturbed vs Undisturbed
27
Common Sampling
Methods
28
GROUND WATER TABLE

LEVEL
Groundwater conditions and the potential for
groundwater seepage are fundamental factors in
virtually all geotechnical analyses and design
studies. Accordingly, the evaluation of
groundwater conditions is a basic element of
almost all geotechnical investigation programs.
Groundwater investigations are of two types as
follows:
Determination of groundwater levels and
pressures.
Measurement of the permeability of the subsurface
materials.
29
FIELD STRENGTH TESTS

The following are the major field tests
for determining the soil strength:
1. Vane shear test (VST).
2. Standard Penetration Test (SPT).
3. Cone Penetration Test (CPT).
4. The Borehole Shear Test (BST).
5. The Flat Dilatometer Test (DMT).
6. The Pressure-meter Test (PMT).
7. The Plate Load Test (PLT).
30
FIELD STRENGTH TESTS
31
Standard Penetration Test

(SPT)
32

(SPT)
33

(SPT)
Corrections are normally applied to the
SPT blow count to account for differences
in:
energy imparted during the test (60%
hammer efficiency)
the stress level at the test depth
The following equation is used to
compensate for the testing factors
(Skempton, 1986):
34

(SPT)
35

(SPT)
36
Correlations between N
values and soil properties
Consistency
Very Soft
Soft
Medium Stiff
Stiff
Very Stiff
Hard
N
0 to 2
2 to 4
4 to 8
8 to 12
15 to 30
> 30
qu (kPa)
< 25
25 to 50
50 to 100
100 to 200
200 to 400
> 400
37
Corrections to N value
Overburden Correction applied to N

value based on chart by Peck, et. al.
(varies from 0.45 to 2)
N=Cn * N where Cn is correction factor
Correction due to dilatancy for fine

sand and silt below gwt having N >
15
N = 15 + 0.5*(N-15)
38
Correlations between N
values and soil properties
N
Compactne
ss
Relative
Density
(%)
0 to 4
Very Loose
0-15
< 28
4 to
10
Loose
15 - 35
28 -30
10 to
30
> 50
Medium
Dense
25 - 65
Very Dense > 85
30 -36
> 41
39
Cone Penetration Test

(CPT)
40

(CPT)
41

(CPT)
42

(CPT)
43

(CPT)
44
The Plate Load Test (PLT)
45
46
47

Scale Effect in Foundation Design
48
Subsoil Exploration Report

1. A description of the scope of the investigation
2. A description of the proposed structure for which the subsoil
exploration has been conducted
3. A description of the location of the site, including any structures
nearby, drainage conditions, the nature of vegetation on the site
and surrounding it, and any other features unique to the site
4. A description of the geological setting of the site
5. Details of the field explorationthat is, number of borings, depths
of borings, types of borings involved, and so on
6. A general description of the subsoil conditions, as determined from
soil specimens and from related laboratory tests, standard
penetration resistance and cone penetration resistance, and soon
7. A description of the water-table conditions
8. Re commendations regarding the foundation, including the type of
foundation recommended, the allowable hearing pressure, and
any special construction procedure that may he needed;
alternative foundation design procedures should also be discussed
in this portion of the report
9. Conclusions and limitations of the investigations
49
Subsoil Exploration Report

The following graphical presentations
should he attached to the report:
1. A site location map
2. A plan view of the location of the
borings with respect to the proposed
structures and those nearby
3. Boring logs
4. Laboratory test results
5. Other special graphical presentations
50
Example Table
of Contents
for
a Geotechnical
Investigation
(Data) Report
51

1 Siteinvestigation

Uploaded by

Copyright:

Available Formats

1 Siteinvestigation

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1 Siteinvestigation

Uploaded by

Copyright:

Available Formats

SITE INVESTIGATION

The purpose of a soil

Determination of the minimum depth of boring

Preparation of Boring Logs

Name and address of the drilling company

Thicker the wall, greater the

GROUND WATER TABLE

FIELD STRENGTH TESTS

FIELD STRENGTH TESTS

Standard Penetration Test

Standard Penetration Test

Standard Penetration Test

Standard Penetration Test

Standard Penetration Test

Overburden Correction applied to N

N=Cn * N where Cn is correction factor

Correction due to dilatancy for fine

Cone Penetration Test

Cone Penetration Test

Cone Penetration Test

Cone Penetration Test

Cone Penetration Test

The Plate Load Test (PLT)

The Plate Load Test (PLT)

The Plate Load Test (PLT)

The Plate Load Test (PLT)

Subsoil Exploration Report

Subsoil Exploration Report

You might also like