Engineering Electromagnetics

W.H. Hayt Jr. and J. A. Buck

Chapter 7:
The Steady Magnetic Field

Motivating the Magnetic Field Concept:

Forces Between Currents
Magnetic forces arise whenever we have charges in motion. Forces between current-carrying wires
present familiar examples that we can use to determine what a magnetic force field should look like:
Here are the easily-observed facts:

How can we describe a force field around wire 1 that can be used to determine the force on wire 2?

Magnetic Field
The geometry of the magnetic field is set up to correctly model forces between currents that
allow for any relative orientation. The magnetic field intensity, H, circulates around its source, I1,
in a direction most easily determined by the right-hand rule: Right thumb in the direction of the
current, fingers curl in the direction of H

Note that in the third case (perpendicular currents), I2 is in the same direction as H, so that their
cross product (and the resulting force) is zero. The actual force computation involves a different
field quantity, B, which is related to H through B = H in free space. This will be taken up in
a later lecture. Our immediate concern is how to find H from any given current distribution.

Biot-Savart Law
The Biot-Savart Law specifies the
magnetic field intensity, H, arising
from a point source current element
of differential length dL.

The units of H are [A/m]

Note in particular the inverse-square
distance dependence, and the fact that
the cross product will yield a field vector
that points into the page. This is a formal
statement of the right-hand rule

Note the similarity to Coulombs Law, in which

a point charge of magnitude dQ1 at Point 1 would
generate electric field at Point 2 given by:

Magnetic Field Arising From a Circulating Current

At point P, the magnetic field associated with
the differential current element IdL is

To determine the total field arising from the closed circuit path,
we sum the contributions from the current elements that make up
the entire loop, or

The contribution to the field at P from any portion of the current will be just the above integral evalated
over just that portion.

Two- and Three-Dimensional Currents

On a surface that carries uniform surface current
density K [A/m], the current within width b is

..and so the differential current quantity that

appears in the Biot-Savart law becomes:

The magnetic field arising from a current

sheet is thus found from the two-dimensional
form of the Biot-Savart law:

In a similar way, a volume current will be made up

of three-dimensional current elements, and so the Biot-Savart
law for this case becomes:

Example of the Biot-Savart Law

In this example, we evaluate the magnetic field intensity on the y axis (equivalently in the xy plane)
arising from a filament current of infinite length in on the z axis.

Using the drawing, we identify:

and so..

so that:

Example: continued
We now have:

Integrate this over the entire wire:

..after carrying out the cross product

Example: concluded
Evaluating the integral:

we have:

finally:

Current is into the page.

Magnetic field streamlines
are concentric circles, whose magnitudes
decrease as the inverse distance from the z axis

Field Arising from a Finite Current Segment

In this case, the field is to be found in the xy plane at Point 2.
The Biot-Savart integral is taken over the wire length:

..after a few additional steps (see Problem 7.8), we find:

Another Example: Magnetic Field from a

Current Loop
Consider a circular current loop of radius a in the x-y plane, which
carries steady current I. We wish to find the magnetic field strength
anywhere on the z axis.
We will use the Biot-Savart Law:

where:

Example: Continued
Substituting the previous expressions, the Biot-Savart Law becomes:

carry out the cross products to find:

but we must include the angle dependence in the radial

unit vector:

with this substitution, the radial component will integrate to zero, meaning that all radial components will
cancel on the z axis.

Example: Continued
Now, only the z component remains, and the integral
evaluates easily:

Note the form of the numerator: the product of

the current and the loop area. We define this as
the magnetic moment:

Amperes Circuital Law

Amperes Circuital Law states that the line integral of H about any closed path
is exactly equal to the direct current enclosed by that path.

In the figure at right, the integral of H about closed paths a and b gives
the total current I, while the integral over path c gives only that portion
of the current that lies within c

Amperes Law Applied to a Long Wire

Symmetry suggests that H will be circular, constant-valued
at constant radius, and centered on the current (z) axis.
Choosing path a, and integrating H around the circle
of radius gives the enclosed current, I:

so that:

as before.

Coaxial Transmission Line

In the coax line, we have two concentric
solid conductors that carry equal and opposite
currents, I.
The line is assumed to be infinitely long, and the
circular symmetry suggests that H will be entirely
- directed, and will vary only with radius .
Our objective is to find the magnetic field
for all values of

Field Between Conductors

The inner conductor can be thought of as made up of a
bundle of filament currents, each of which produces the
field of a long wire.
Consider two such filaments, located at the same
radius from the z axis, , but which lie at symmetric
coordinates, and -Their field contributions
superpose to give a net H component as shown. The
same happens for every pair of symmetrically-located
filaments, which taken as a whole, make up the entire
center conductor.
The field between conductors is thus found to be the same
as that of filament conductor on the z axis that carries current,
I. Specifically:

a < < b

Field Within the Inner Conductor

With current uniformly distributed inside the conductors, the H can be assumed circular everywhere.
Inside the inner conductor, and at radius we again have:

But now, the current enclosed is

so that

or finally:

Field Outside Both Conducors

Outside the transmission line, where > c,
no current is enclosed by the integration path,
and so

0
As the current is uniformly distributed, and since we
have circular symmetry, the field would have to
be constant over the circular integration path, and so it
must be true that:

Field Inside the Outer Conductor

Inside the outer conductor, the enclosed current consists
of that within the inner conductor plus that portion of the
outer conductor current existing at radii less than
Amperes Circuital Law becomes

..and so finally:

Magnetic Field Strength as a Function of Radius in

the Coax Line
Combining the previous results, and assigning dimensions as shown in the inset below, we find:

Magnetic Field Arising from a Current Sheet

For a uniform plane current in the y direction, we expect an x-directed H field from symmetry.
Applying Amperes circuital law to the path

we find:

or
In other words, the magnetic field is discontinuous across the current sheet by the magnitude of the surface
current density.

Magnetic Field Arising from a Current Sheet

If instead, the upper path is elevated to the line between

and

, the same current is enclosed and we would have

from which we conclude that

so the field is constant in each region (above and below the current plane)

By symmetry, the field above the sheet must be

the same in magnitude as the field below the sheet.
Therefore, we may state that

and

Magnetic Field Arising from a Current Sheet

The actual field configuration is shown below, in which magnetic field above the current sheet is
equal in magnitude, but in the direction opposite to the field below the sheet.

The field in either region is found by the cross product:

where aN is the unit vector that is normal to the

current sheet, and that points into the region in
which the magnetic field is to be evaluated.

Magnetic Field Arising from Two Current Sheets

Here are two parallel currents, equal and opposite, as you would find in a parallel-plate
transmission line. If the sheets are much wider than their spacing, then the magnetic field
will be contained in the region between plates, and will be nearly zero outside.
Hx2 (z > d/2 )
Hx1 (z > d/2 )

These fields cancel for current sheets of

infinite width.

K1 = -Ky ay
Hx1 (-d /2 < z < d/2 )
Hx2 (-d /2 < z < d/2 )
K2 = -Ky ay

These fields are equal and add to give

H = K x aN (-d/2 < z < d/2 )

where K is either K1 or K2

Hx1 (z < -d/2 )

Hx2 (z < -d/2 )

These fields cancel for current sheets of

infinite width.

Current Loop Field

Using the Biot-Savart Law, we previously found the magnetic
field on the z axis from a circular current loop:

We will now use this result as a building block

to construct the magnetic field on the axis of
a solenoid -- formed by a stack of identical current
loops, centered on the z axis.

On-Axis Field Within a Solenoid

We consider the single current loop field as a differential
contribution to the total field from a stack of N closely-spaced
loops, each of which carries current I. The length of the stack
(solenoid) is d, so therefore the density of turns will be N/d.

z
d/2

Now the current in the turns within a differential length, dz, will be
We consider this as our differential loop current
so that the previous result for H from a single loop:

-d/2

now becomes:
in which z is measured from the center of the coil,
where we wish to evaluate the field.

Solenoid Field, Continued

The total field on the z axis at z = 0 will be the sum of the
field contributions from all turns in the coil -- or the integral
of dH over the length of the solenoid.
z
d/2

-d/2

Approximation for Long Solenoids

We now have the on-axis field at the solenoid midpoint (z = 0):
z
d/2

Note that for long solenoids, for which

result simplifies to:

, the
-d/2

This result is valid at all on-axis positions deep within long coils -- at distances from each end of several radii.

Another Interpretation: Continuous Surface Current

The solenoid of our previous example was assumed to have many tightly-wound turns, with several
existing within a differential length, dz. We could model such a current configuration as a continuous
surface current of density K = Ka a A/m.

d/2
Therefore:

-d/2

In other words, the on-axis field magnitude near the center of a cylindrical
current sheet, where current circulates around the z axis, and whose length
is much greater than its radius, is just the surface current density.

Solenoid Field -- Off-Axis

To find the field within a solenoid, but off the z axis, we apply Amperes Circuital Law in the following way:
The illustration below shows the solenoid cross-section, from a lengthwise cut through the z axis. Current in
the windings flows in and out of the screen in the circular current path. Each turn carries current I. The magnetic
field along the z axis is NI/d as we found earlier.

Application of Amperes Law

Applying Amperes Law to the rectangular path shown below leads to the following:

Where allowance is made for the existence of a radial H component,

Radial Path Segments

The radial integrals will now cancel, because they are oppositely-directed, and because in the long coil,
is not expected to differ between the two radial path segments.

Completing the Evaluation

What is left now are the two z integrations, the first of which we can evaluate as shown. Since
this first integral result is equal to the enclosed current, it must follow that the second integral -- and
the outside magnetic field -- are zero.

Finding the Off-Axis Field

The situation does not change if the lower z-directed path is raised above the z axis. The vertical
paths still cancel, and the outside field is still zero. The field along the path A to B is therefore NI/d
as before.

Conclusion: The magnetic field within a long solenoid is approximately constant throughout the coil
cross-section, and is Hz = NI/d.

Toroid Magnetic Field

A toroid is a doughnut-shaped set of windings around a core material. The cross-section could be
circular (as shown here, with radius a) or any other shape.
Below, a slice of the toroid is shown, with current
emerging from the screen around the inner periphery
(in the positive z direction). The windings are modeled
as N individual current loops, each of which carries current I.

Amperes Law as Applied to a Toroid

Amperes Circuital Law can be applied to a toroid by taking a closed loop integral
around the circular contour C at radius Magnetic field H is presumed to be circular,
and a function of radius only at locations within the toroid that are not too close to the
individual windings. Under this condition, we would assume:

This approximation improves as the density of turns gets higher

(using more turns with finer wire).
Amperes Law now takes the form:

so that.

Performing the same integrals over contours drawn

in the regions
or
will
lead to zero magnetic field there, because no current
is enclosed in either case.

Surface Current Model of a Toroid

Consider a sheet current molded into a doughnut shape, as shown.
The current density at radius
crosses the xy plane in the z
direction and is given in magnitude by Ka
Amperes Law applied to a circular contour C inside the
toroid (as in the previous example) will take the form:

leading to

inside the toroid. and the field is zero outside as before.

Amperes Law as Applied to a Small Closed Loop.

Consider magnetic field H evaluated at the point

shown in the figure. We can approximate the field
over the closed path 1234 by making appropriate
adjustments in the value of H along each segment.
The objective is to take the closed path integral
and ultimately obtain the point form of Amperes Law.

Approximation of H Along One Segment

Along path 1-2, we may write:

where:

And therefore:

Contributions of y-Directed Path Segments

The contributions from the front and back sides will be:

The contribution from the opposite side is:

Note the path directions as specified in the figure, and

how these determine the signs used .
This leaves the left and right sides..

Contributions of x-Directed Path Segments

Along the right side (path 2-3):

and the contribution from the left side (path 4-1) is:

The next step is to add the contributions of all four sides to find the closed path integral:

Net Closed Path Integral

The total integral will now be the sum:

and using our previous results, the becomes:

Relation to the Current Density

By Amperes Law, the closed path integral of H is equal to the enclosed current, approximated in
this case by the current density at the center, multiplied by the loop area:

Dividing by the loop area, we now have:

The expression becomes exact as the loop area

approaches zero:

Other Loop Orientations

The same exercise can be carried with the rectangular loop in the other two orthogonal orientations.
The results are:

Loop in yz plane:

Loop in xz plane:

Loop in xy plane:

This gives all three components of the current density field.

Curl of a Vector Field

The previous exercise resulted in the rectangular coordinate representation of the Curl of H.
In general, the curl of a vector field is another field that is normal to the original field.
The curl component in the direction N, normal to the plane of the integration loop is:

The direction of N is taken using the right-hand convention: With fingers of the right hand oriented
in the direction of the path integral, the thumb points in the direction of the normal (or curl).

Curl in Rectangular Coordinates

Assembling the results of the rectangular loop integration exercise, we find the vector field
that comprises curl H:

An easy way to calculate this is to evaluate the following determinant:

which we see is equivalent to the cross product of the del operator with the field:

Curl in Other Coordinate Systems

a little more complicated!

Look these up as needed.

Visualization of Curl
Consider placing a small paddle wheel in a flowing stream of water, as shown below. The wheel
axis points into the screen, and the water velocity decreases with increasing depth.
The wheel will rotate clockwise, and give a curl component that points into the screen (right-hand rule).

Positioning the wheel at all three orthogonal orientations will yield measurements of
all three components of the curl. Note that the curl is directed normal to both the field
and the direction of its variation.

Another Maxwell Equation

It has just been demonstrated that:

..which is in fact one of Maxwells equations for static fields:

This is Amperes Circuital Law in point form.

.and Another Maxwell Equation

We already know that for a static electric field:

This means that:

(applies to a static electric field)

Recall the condition for a conservative field: that is, its closed path integral is zero everywhere.

Therefore, a field is conservative if it has zero curl at all points over which the field is defined.

Curl Applied to Partitions of a Large Surface

Surface S is paritioned into sub-regions, each of small area
The curl component that is normal to a surface element can
be written using the definition of curl:

or:

We now apply this to every partition on the surface, and add the results.

Adding the Contributions

Cancellation here:
We now evaluate and add the curl contributions
from all surface elements, and note that
adjacent path integrals will all cancel!
This means that the only contribution to the
overall path integral will be around the outer
periphery of surface S.
No cancellation here:

Using our previous result, we now write:

Stokes Theorem
We now take our previous result, and take the limit as

In the limit, this side

becomes the path integral
of H over the outer perimeter
because all interior paths
cancel

In the limit, this side

becomes the integral
of the curl of H over
surface S

The result is Stokes Theorem

This is a valuable tool to have at our disposal, because it gives us two ways to evaluate the same thing!

Obtaining Amperes Circuital Law in Integral Form,

using Stokes Theorem
Begin with the point form of Amperes Law for static fields:

Integrate both sides over surface S:

..in which the far right hand side is found from the left hand side
using Stokes Theorem. The closed path integral is taken around the
perimeter of S. Again, note that we use the right-hand convention in
choosing the direction of the path integral.
The center expression is just the net current through surface S,
so we are left with the integral form of Amperes Law:

Magnetic Flux and Flux Density

We are already familiar with the concept of electric flux:

Coulombs

in which the electric flux density in free space is:

and where the free space permittivity is

In a similar way, we can define the magnetic flux in units of Webers (Wb):
Webers

in which the magnetic flux density (or magnetic induction) in free space is:
and where the free space permeability is
This is a defined quantity, having to do with the definition of the ampere (we will explore this later).

A Key Property of B
If the flux is evaluated through a closed surface, we have in the case of electric flux, Gauss Law:

If the same were to be done with magnetic flux density, we would find:

The implication is that (for our purposes) there are no magnetic charges
-- specifically, no point sources of magnetic field exist. A hint of this has already
been observed, in that magnetic field lines always close on themselves.

Another Maxwell Equation

We may rewrite the closed surface integral of B using the divergence theorem, in which the
right hand integral is taken over the volume surrounded by the closed surface:

Because the result is zero, it follows that

This result is known as Gauss Law for the magnetic field in point form.

Maxwells Equations for Static Fields

We have now completed the derivation of Maxwells equations for no time variation. In point form, these are:

Gauss Law for the electric field

Conservative property of the static electric field
Amperes Circuital Law
Gauss Law for the Magnetic Field

where, in free space:

Significant changes in the above four

equations will occur when the fields are
allowed to vary with time, as well see later.

Maxwells Equations in Large Scale Form

The divergence theorem and Stokes theorem can be applied to the previous four point form equations
to yield the integral form of Maxwells equations for static fields:

Gauss Law for the electric field

Conservative property of the static electric field

Amperes Circuital Law

Gauss Law for the magnetic field

Example: Magnetic Flux Within a Coaxial Line

Consider a length d of coax, as shown here. The magnetic field strength between conductors is:

and so:

The magnetic flux is now the integral of B over the

flat surface between radii a and b, and of length d along z:

The result is:

The coax line thus stores this amount of magnetic flux in the region between conductors.
This will have importance when we discuss inductance in a later lecture.

Scalar Magnetic Potential

We are already familiar with the relation between the scalar electric potential and electric field:

So it is tempting to define a scalar magnetic potential such that:

This rule must be consistent with Maxwells equations, so therefore:

But the curl of the gradient of any function is identically zero! Therefore, the scalar magnetic potential
is valid only in regions where the current density is zero (such as in free space).
So we define scalar magnetic
potential with a condition:

Further Requirements on the Scalar Magnetic Potential

The other Maxwell equation involving magnetic field must also be satisfied. This is:

in free space

Therefore:
..and so the scalar magnetic potential satisfies Laplaces equation (again with the restriction
that current density must be zero:

Example: Coaxial Transmission Line

With the center conductor current flowing out of the screen, we have

Thus:

So we solve:

.. and obtain:
where the integration constant has been set to zero

Ambiguities in the Scalar Potential

The scalar potential is now:

where the potential is zero at

At point P (

) the potential is

But wait! As increases to

we have returned to the same physical location, and
the potential has a new value of -I.
In general, the potential at P will be multivalued, and will
acquire a new value after each full rotation in the xy plane:

Overcoming the Ambiguity

To remove the ambiguity, we construct a mathematical barrier at any value of phi. The angle domain
cannot cross this barrier in either direction, and so the potential function is restricted to angles on either
side. In the present case we choose the barrier to lie at
so that

The potential at point P is now single-valued:

Barrier at

Vector Magnetic Potential

We make use of the Maxwell equation:
.. and the fact that the divergence of the curl of any vector field is identically zero (show this!)

This leads to the definition of the magnetic vector potential, A:

Thus:

and Amperes Law becomes

Equation for the Vector Potential

We start with:

Then, introduce a vector identity that defines the vector Laplacian:

Using a (lengthy) procedure (see Sec. 7.7) it can be proven that

We are therefore left with

The Direction of A
We now have

In rectangular coordinates:
(not so simple in the
other coordinate systems)
The equation separates to give:

This indicates that the direction of A will be the same as that of the current to which it is associated.
The vector field, A, existing in all space, is sometimes described as being a fuzzy image
of its generating current.

Expressions for Potential

Consider a differential elements, shown here. On the left is a point charge represented
by a differential length of line charge. On the right is a differential current element. The setups
for obtaining potential are identical between the two cases.
Line Charge

Scalar Electrostatic Potential

Line Current

Vector Magnetic Potential

General Expressions for Vector Potential

For large scale charge or current distributions, we would sum the differential
contributions by integrating over the charge or current, thus:

and

The closed path integral is taken because the current must

close on itself to form a complete circuit.

For surface or volume current distributions, we would have, respectively:

or

in the same manner that we used for scalar electric potential.

Example
We continue with the differential current element as shown here:
In this case

becomes at point P:

Now, the curl is taken in cylindrical coordinates:

This is the same result as found using the Biot-Savart Law (as it should be)