Steam Power Plant

PROJECT ON
STEAM POWER PLANT

PRESENTED BY:
CHANCHAL KUMAR GORAI-1201298417
DEODUTTA KUMAR
-1201298544
AQUIL HAIDER
-1201298450
DHANANJOY MAHTO
-1201298545
GUIDED BY:
prof. RAM CHANDRA PARIDA
CONTENTS
INTRODUCTION
CARNOT VAPOUR CYCLE
IDEAL RANKINE CYCLE
WORKING
BOILER
TURBINE
CONDENSER
COOLING TOWER
WAY TO INCREASE EFFICIENCY
RE-HEATING
RE-GENERATION
SUPER-HEATING
POLLUTION IN POWER PLANT
CONCLUSION
INTRODUCTION
Thermodynamics cycles can be divided into two
generation categories :
Power Cycles
Refrigeration Cycles
The devices or systems used to produce a net
power output are often called engines and the
thermodynamics cycles they operate on are called
power cycle.
The devices or systems use to produce
refrigeration are called refrigerator, air
conditioners or heat pumps and the cycles they
operates on are called refrigeration cycles.
Gas Cycles : In gas cycles, the working fluid
remains in the gaseous phase throughout the

entire cycle
Vapour Cycles :In vapour cycles the working
fluid exists in the vapour phase during one

part of the cycle and in the liquid phase
during another part.
Heat Engines: Heat engines are designed for
the purpose of converting other form of

energy to work .
CARNOT VAPOUR POWER CYCLE

The Carnot cycle is
composed of 4 totally
reversible processes :
Isothermal heat addition at
high temperature (TH).
Isentropic expansion from
high temperature to low
temperature.
Isothermal heat rejection at
low temperature (TL).
Isentropic compression from
low temperature to high
temperature.
Ideal Rankine Cycle

Rankine Cycle : The
Ideal Cycle for Vapour

Power Cycle
1-2 : Isentropic
compression in pump
2-3 : Constant pressure
heat addition in boiler
3-4 : Isentropic
expansion in turbine
4-1 : Constant pressure
heat rejection in a
condenser
The McGraw-Hill
Companies, Inc.,1998
WORKING
A furnace to burn the
fuel.
Steam generator or
boiler
containing
water. Heat generated
in the furnace is
utilized to convert
water into steam.
Main power unit
such as an engine or
turbine to use the heat
energy of steam and
perform work.
Piping system to
convey steam and
water.
BOILER
Vessel that heats water to become hot water or steam
At atmospheric pressure water volume increases 1,600 times
Hot water or steam used to transfer heat to a process
TYPES OF BOILER
According to flow of water and hot gases :
Water tube
Fire tube
1. Fire Tube Boiler
Relatively small steam

capacities
(12,000
kg/hour)
Low to medium steam
pressures (18 kg/cm2)
Operates with oil, gas or
solid fuels
2. Water Tube Boiler

Used for high steam demand and
pressure requirements
Capacity range of 4,500
120,000 kg/hour
Combustion efficiency enhanced
by induced draft provisions
Lower tolerance for water quality
and needs water treatment plant
TURBINES
A steam turbine is a mechanical
device that extracts thermal

energy from pressurized steam,
and converts it into rotary
motion. It has almost completely
replaced the reciprocating piston
steam engine primarily because
of its greater thermal efficiency
and higher power-to-weight ratio.
Because the turbine generates
rotary motion, it is particularly
suited to be used to drive an
electrical generator about 80%
of all electricity generation in the
world is by use of steam turbines.
Generally two types of

turbine are used
IMPULSE
REACTION
CONDENSER
The
main purposes of the

condenser are to condense the
exhaust steam from the turbine for
reuse in the cycle and to maximize
turbine efficiency by maintaining
proper vacuum.
As the operating pressure of the
condenser is lowered (vacuum is

increased), the enthalpy drop of
the expanding steam in the turbine
will also increase. This will
increase the amount of available
work from the turbine (electrical
output).
Cooling Tower
The importance of the cooling
tower is felt when the cooling

water from the condenser has to
be cooled.
The
cooling water after

condensing the steam becomes
hot and it has to be cooled as it
belongs to a closed system. The
Cooling towers do the job of
decreasing the temperature of
the
cooling
water
after
condensing the steam in the
condenser.
WAY TO INCREASE EFFICIENCY

Lowering the condenser pressure.
Superheating the steam to high
temperatures.
Increasing the boiler pressure.
Ideal Reheat Rankine Cycle

The efficiency of the
Rankine cycle can

increase by
expanding the steam
in the turbine in two
stages, and
reheating it in
between. Reheating
is a practical solution
to the excessive
moisture problem in
turbines, and it is
commonly used in
modern steam power
plants.
REGENERATION
Another way of increasing the
thermal efficiency of the

Rankine cycle is by
regeneration.
Open Feed-water
Heater :
An open (or direct-contact)
feed-water heater is basically a

mixing chamber, where the
steam extracted from the
turbine mixes with the feedwater exiting the pump. Ideally,
the mixture leaves the heater
Closed feed-water
heater :
Another type of feedwater heater used is
steam power plants is
the closed feed-water
heater in which heat is
transferred from the
extracted steam to the
feed-water without
any mixing taking
place. The two
streams now can be at
different pressure,
since they do not mix.
ADVANTAGE OF FEED WATER HEATER

Feed water heating improves overall plant
efficiency.
Quantity of steam produced by boiler is
increase.
Thermal stress due to cold water entering the
boiler drum is avoided.
Chance of boiler corrosion decreases.
SUPER-HEATER
It is a heating device.
It is used to raise temp of steam at const pressure.
It removes even last traces of moisture.
ADVANTAGES
Capacity to do work is increased without increasing its pressure.
High temperature of super heated steam results in an increase in
thermal efficiency.
Heat losses due to condensation of stem on cylinder walls are
avoided to a great extent.
Does not produce corrosion effect on turbine.
POLLUTION IN POWER PLANT

Pollution can be define as the contamination of soil, air and
water with undesirable amount of material and heat.

Non toxic dust
Sulphur dioxide
Carbon monoxide
Nitrogen dioxide
Soot (fly ash)
Hydrogen sulphide
Pollution control
SOx
- use alternative fuel.

- low sulphur containing fuel.
- lime dosing.
Nox
-NH3 injection.
-Flue gas recirculation.
CO
-proper burning with O2.
Coal dust- covered storage yard for coal.
CONCLUSION
As 60% of total power generation is done
steam power plant.

It is the biggest source of electricity.
We should control pollution.
Suitable step should taken to increase the
efficiency.
So that we can use more power.
THANK YOU.

Steam Power Plant

Uploaded by

Copyright:

Available Formats

Steam Power Plant

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Steam Power Plant

Uploaded by

Copyright:

Available Formats

PROJECT ON

STEAM POWER PLANT

Gas Cycles : In gas cycles, the working fluid

remains in the gaseous phase throughout the

fluid exists in the vapour phase during one

the purpose of converting other form of

CARNOT VAPOUR POWER CYCLE

Ideal Rankine Cycle

Ideal Cycle for Vapour

Vessel that heats water to become hot water or steam

At atmospheric pressure water volume increases 1,600 times

Hot water or steam used to transfer heat to a process

1. Fire Tube Boiler

Relatively small steam

2. Water Tube Boiler

device that extracts thermal

Generally two types of

main purposes of the

As the operating pressure of the

condenser is lowered (vacuum is

tower is felt when the cooling

cooling water after

WAY TO INCREASE EFFICIENCY

Ideal Reheat Rankine Cycle

Rankine cycle can

thermal efficiency of the

An open (or direct-contact)

feed-water heater is basically a

ADVANTAGE OF FEED WATER HEATER

POLLUTION IN POWER PLANT

water with undesirable amount of material and heat.

- use alternative fuel.

As 60% of total power generation is done

steam power plant.

You might also like