MTBE

ABDALLAH ALHARABAH
INTRODUCTION
INTRODUCTION
Problem Statement
This term's problem is to design an MTBE plant that produces

2000 tons MTBE per day.
MTBE is a gasoline additive used to increase octane number that is

produced from methanol and isobutylene. MTBE is produced by a
liquid-phase reaction over a catalyst. The reaction is between
isobutene and methanol as follows:
(CH3)2C=CH2 + CH3OH
(CH3)3C-O-CH3
INTRODUCTION
Problem Statement
Pure Methanol
The reactor
30 bar and 90 C
MTBE
2000 ton/day
Mixture :
-40% isobutylene
-55% isobutane
-5% propane
The isobutene and propane are inert. The conversion is
95% and the selectivity is one.
Outlines
INTRODUCTION
MTBE SYNTHSIS
- Raw Material
- Properties and Thermodynamics
MTBE PROCESSES
- Process Description
- Process Flow Diagram (PFD)
- Uses and Alternatives
- Safety
INTRODUCTION
known as methyl tertiary butyl ether
MTBE is a chemical compound with molecular formula C 5H12O.
It has been used since 1979 when it was first added to
gasoline to replace lead as an anti-knock agent and to boost
octane.
MTBE oxygenate has achieved a great economic importance
in recent years as a gasoline additive because of its ability to
enhance the octane value of unleaded motor gasoline while
increasing the oxygen content.
MTBE is produced by the reaction of isobutylene and
methanol in the presence of a cation exchange resin catalyst
Amberlyst 15.
INTRODUCTION
MTBE is also used in organic chemistry as a relatively inexpensive

solvent with properties comparable to diethyl ether but with a higher
boiling point and lower solubility in water.
It is also used medically to dissolve gallstones.
Raw Material
RAW MATERIAL
known as methyl alcohol
its molecular formula is CH3OH.
Methanol was formerly produced by the destructive
distillation of wood.
The modern method of preparing methanol is based on
the direct combination of carbon monoxide gas and
hydrogen in the presence of a catalyst.
Most methanol is produced from the methane which is
found in natural gas.
RAW MATERIAL
known as methyl alcohol
Pure methanol is an important material in chemical
synthesis.
Methanol is a colorless liquid, completely miscible with
water and organic solvents and is very hydroscopic. It boils at
64.96 C (148.93 F) and solidifies at -93.9 C (-137 F).
It forms explosive mixtures with air and burns with a
nonluminous flame. It is a violent poison; drinking mixtures
containing methanol has caused many cases of blindness or
death. Methanol has a settled odor.
RAW MATERIAL
known as 2-methylpropene with a formula C4H8
It is called olefin because it contains a four-carbon
branched alkene.
It is colarless gas and on of the important hydrocarbon in
industrial.
Isobutylene is used as an intermediate in the production of
a variety of products.
It is reacted with methanol and ethanol in the manufacture
of the gasoline oxygenates methyl tert-butyl ether (MTBE)
and ethyl tert-butyl ether (ETBE), respectively. Alkylation with
butane produces isooctane, another fuel additive.
RAW MATERIAL
It is molecular formula C3H8
Propane is a colorless, flammable gas at atmospheric

pressure and normal temperatures.
It has a natural gas odor and is soluble in ether, alcohol and
slightly soluble in water.
Typical uses include vehicle fuel, home heating, and
refrigerant gas.
Properties and Thermodynamics

MTBE properties
Molecular weight (g/mole)
88.15
Boiling Temperature ( C)
54
Specific gravity
0.74
Water solubility (mg/L)
50000
Vapor pressure (mm Hg)
251
Henry's Law
1.5E-3
Latent heat of vaporization (Cal/g)
81.7
Specific heat (Cal/g.C)
0.51

known as methyl alcohol with a formula
CH3OH

known as methyl alcohol with a formula
CH3OHMethanol properties
32.04
Boiling Temperature (C )
65
Melting pint (C )
Relative Density
Specific gravity
Water solubility (mg/L)
Vapor pressure (mm Hg)
Heat of Formation (MJ/kmol)
-97.7
0.79
0.8
infinity
122
201.3-
Gibbs Free Energy

Tc (K)
Pc (bar)
Vc ( m/kmol)
Density ( kg/m)
Heat of Vaporization (kJ/kmol)
-162.62
512.6
81
0.118
791
35278
Henry's Law
1.1E-4

Butenes properties
Melting pint (C )
Specific gravity
Water solubility (mg/ml)
Vapor pressure ( kPa)
Flash point (c)
Tc (c)
Pc (atm)
Vc ( cm/mol)
Density ( g/cm) gas
Latent Heat of Vaporization
(cal/g)
Specific heat (kj/kg.k)
isobutylene
butene-1
56.11
6.9-
56.107
-6.3
140.30.59
insoluble
268.8
76144.739.48
239
-185.4
1.998
0.085
268
-79
146.4
40.2
-
0.5879
94.3
2.72(kg/m)
390 (kj/kg)
1.487
0.083 (kj/mol.k)

It is molecular formula C3H8
Propane properties
44.1
-42.09
Melting pint (C )
Specific gravity
Water solubility (mg/ml)
Vapor pressure (psig)
Viscosity (centipoise)
Gibbs Free Energy
Tc (F)
Pc (psia)
Density ( kg/m) gas
Density ( kg/m) liquid
Heat of Vaporization (cal/g)
Specific heat (cal/g.c)
-187.6
1.5503
0.07
109
0.008029
-162.62
206.2
617.4
1.83
507.7
101.76
0.3885
Process Description
Process Description
(MTBE) is a gasoline additive used to increase octane number

that is produced from methanol and isobutylene.
Methanol is purchased but the isobutylene is obtained from
the isomerization and dehydrogenation of butane .
Butene waste
stream
Water
Methanol Recycle
Column
Butenes
MTBE
Reacto
r
MTBE Column
Methanol
Methanol
Scrubber
MTBE
Waste
stream
Process Description
The Butenes stream contains 40% isobutylene, 55% isobutene

and and 5% light gases mainly propane
Butene waste
stream
Water
Methanol Recycle
Column
Butenes
MTBE
Reacto
r
MTBE Column
Methanol
Methanol
Scrubber
MTBE
Waste
stream
Process Description
The MTBE produced is extracted from the reaction effluent via

distillation, while the unreacted methanol is absorbed by water
before it is separated from water via distillation. The recoverd
methanol is recycled back to the reactor.
Butene waste
stream
Water
Methanol Recycle
Column
Butenes
MTBE
Reacto
r
MTBE Column
Methanol
Methanol
Scrubber
MTBE
Waste
stream
Process Description
MTBE is produced by a liquid-phase reaction over a catalyst. The

reaction is between isobutylene and methanol as follows:
(CH3)2C=CH2 + CH3OH (CH3)3C-O-CH3

Butene waste
stream
Water
Methanol Recycle
Column
Butenes
MTBE
Reacto
r
MTBE Column
Methanol
Methanol
Scrubber
MTBE
Waste
stream
Process Flow Diagram (PFD)
Process Flow Diagram

R -9 0 1
M TBE
R e a c to r
T -9 0 1
M TBE
C o lu m n
T -9 0 2
M e th a n o l
S c ru b b e r
T -9 0 3
M e th a n o l
R e c y c le
C o lu m n
11
p ro c e s s
w a te r
b u te n e
w a s te s tre a m
3
m e th a n o l
T -9 0 2
b u te n e s
R -9 0 1
10
T -9 0 3
w a s te
w a te r
T -9 0 1
12
M TBE
F ig u r e 1 : P r o c e s s F lo w D ia g r a m fo r M T B E P r o d u c tio n
Kinetic Data and Uses
The catalyst used in this reaction is Amberlyst 15.

A kinetic model for the liquid phase reaction using
Amberlyst 15 as a catalyst is
Uses
MTBE has many properties that make it a good gasoline
component for technical and environmental reasons:
MTBE can be used as fuel that can supplement the
supply of gasoline components.
Its high octane rating makes it an ideal substitute for
other octane components, e.g. lead.
It is an oxygenate, which can be used in the
formulation of cleaner-burning gasoline.
Safety
Safety
Safety is very important in the plant because any small mistakes will
cost money. For example:
in reactor we should have a jacket or coil to cool the reactor
because the reaction is exothermic and isothermal. If we don't have
cooler the reaction temperature with time will increase and that will
lead to break the catalyst and explosion.
Also in the distillation column limit the maximum height to 53 m
because of wind load and foundation considerations
Safety
Also we need to use spare pump because if the primary pump is
not working we don't have problem.
Moreover we need to use PID tuning to control the process
conditions like temperature and pressure.
Also some safety factors will required in the design's calculation

to avoid problems.
??
?

MTBE

Uploaded by

Copyright:

Available Formats

MTBE

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MTBE

Uploaded by

Copyright:

Available Formats

ABDALLAH ALHARABAH

This term's problem is to design an MTBE plant that produces

MTBE is a gasoline additive used to increase octane number that is

MTBE is also used in organic chemistry as a relatively inexpensive

Propane is a colorless, flammable gas at atmospheric

Properties and Thermodynamics

Properties and Thermodynamics

Water solubility (mg/L)

Vapor pressure (mm Hg)

Latent heat of vaporization (Cal/g)

Specific heat (Cal/g.C)

Properties and Thermodynamics

Properties and Thermodynamics

Gibbs Free Energy

Properties and Thermodynamics

Properties and Thermodynamics

(MTBE) is a gasoline additive used to increase octane number

The Butenes stream contains 40% isobutylene, 55% isobutene

The MTBE produced is extracted from the reaction effluent via

MTBE is produced by a liquid-phase reaction over a catalyst. The

(CH3)2C=CH2 + CH3OH (CH3)3C-O-CH3

Process Flow Diagram (PFD)

Process Flow Diagram

Process Flow Diagram

Kinetic Data and Uses

Process Flow Diagram

The catalyst used in this reaction is Amberlyst 15.

Also some safety factors will required in the design's calculation

You might also like