Introductions To: Deep Foundations

Introductions to
DEEP FOUNDATIONS
Chapter#04
ENGR. IMRAN
HAFEEZ
Introduction
It is a foundation unit that provides support for a
structure by the toe resistance (end resistance)
in a competent soil or rock at some depth below
the structure and/or by the shaft resistance (skin
resistance) in the soil or rock in which it is placed
Depth/Width >4
If this situation is such that we cannot use
shallow foundation due to the reasons that
It may not perform well.
It is not economical.
So at this stage we think for some other
alternative and the other alternative is Deep
Foundation.
CLASSIFICATION OF DEEP
FOUNDATIONS:
The types of deep foundations are

Pile
Pier
Coissons
Well-foundation
Sheet Piles
Caissons are or well foundations are heavier

in section and they are sunk to the required
depth.
Pile Foundations
A timber, steel or reinforced concrete post
usually vertical, used as a structural
element for transferring the loads at the
required depth in the deep foundations is
called PILE.
These are the long slender members either
driven or cast-in-situ and may be
subjected to vertical or later or vertical
plus lateral loads.
.
USE OF PILES:
Piles may be used for the following purposes,
1. End Bearing or compressive strength: To transfer
the load through a soft soil to a suitable bearing
stratum by means of end bearing of the piles.
2. Scour depth. To transfer the load through Water,
for any hydraulic structure because in this case,
we have to keep the foundation at the scour
depth below the bed level. For River Ravi
Scour depth is 30 to 35m below the bed. So if
we go for the shallow foundation, we will have to
make an open pit, coffer dam diversion of River
etc. and it is highly uneconomical.
3. Tension or Uplift: For a very tall structure
(tower), even if the Soil is very good, but here
the overturning is the problem. So either make
the base very large (Thick raft) or make deep
foundation.
USE OF PILES:
. Vibration Control: if a machine is generating high vibrations,
then to absorb the vibrations either make a massive block
or the next choice is deep foundation, But Massive black is
very expensive. e.g. At Terbela the shaft of Turbine is 2m
and when it runs there area a lot of vibrations.
5) Compaction Piles: In order to compact the granular soils
and to increase their bearing capacity, piles are used
(compaction Piles).
6) Anchor Piles: To provide Anchorage against horizontal pull
from sheet piling walls or other pulling forces.
7) Fender piles: To protect Water front structure against
impact from ships or other floating objects.
8) Batter piles: To resist large horizontal or inclined forces ().
9) Rapid Construction: Piles can also be used if the time
schedule has much importance.
4
CLASSIFICATION OF
PILES:
With respect to:
1.mode of construction
2.material of construction
3.material of load
4.function of pile
5.Shape
6.size
CLASSIFICATION W.R.T MODE OF

CONSTRUCTION:
1. Driven Piles
(Pre-cast)
2. Cast in-situ Piles (Bored Piles)
3. Under sized Bore.(It is feasible because of
less noise , under sized hole is dug and full
size pile is driven, (NABWI MOSQUE PILES).
By driving the piles, the soil is displaced so
type is
a) High volume displaced piles (vol. almost
equal to vol.of pile).
b) No volume displaced piles.
c) Low volume displaced piles.
CLASSIFICATION W.R.T MATERIAL OF

CONSTRUCTION:
1)Timber piles: (Trunk of a Wooden

tree, the oldest pile)
2)Concrete pile
3)Steel pile
4)Composite pile: (Certain portion by
one material and certain portion by
other material)
CLASSIFICATION W.R.T MATERIAL OF

LOAD:
Some times skin friction is predominant

and sometimes the End bearing so
1)Frictional Pile
If major part is taken by the shaft of pile.
When very Weak soils of large depths are
available.
2)End Bearing Pile
When a soil layer of reasonable strength is
available at a reasonable depth.
3.Combination of Two.
CLASSIFICATION W.R.T FUNCTION OF

PILE:
1) Compression pile: (To resist the comp. load)
2) Tension pile or Anchor pile
3) Compaction pile: (granular soil i.e. very
loose sand can be compacted by driving the
piles at one place, then are pulled out and
driven at the next place, in this way sand is
denisfied).
4) Fander piles: (Used near sea-part to protect
the Harbour, just to absorb the impact of
floating objects)
5) Batter piles: (Provided at an inclination their
stability is more against overturning).
6) Sheet piles.(To reduce seepage or to prascle
lateral stability).
CLASSIFICATION W.R.T
SHAPE:
1.
2.
3.
4.
5.
6.
7.
8.
Round Piles
Square Piles
Octognal Piles
I-Shaped Piles
Straight Piles
Tappered Piles
Bell-Bottom Piles
Screw Piles
CLASSIFICATION W.R.T
SIZE:
1. Small Dia Pile: ( > 6 to 24)
2. Large Dia Pile: ( > 24)
3. Micro Dia Pile: ( = 4 to 6)
4. (These are used for specific projects I,e for Repair ).
5. Root Pile (Rectangular in Italy) Used

for special projects i,e for under
pressing, Repair).
If > 24 then These are called as pier
Selection of Pile
Selection of type, length and capacity
of pile is based on two parameters
a. Soil conditions
b. Magnitude of load
Before the actual construction
begins, pile load tests must be
made to verify the design values
and the foundation design must be
revised according to the test results.
Factors effecting the selection

of pile
1. Length of pile in relation to the load and type
of soil
2. Character of structure
3. Availability of materials
4. Type of loading
5. Factors causing deterioration
6. Ease of maintenance
7. Estimated costs of types of piles, taking into
account the initial cost, life expectancy and
cost of maintenance.
8. Availability of funds

Introductions To: Deep Foundations

Uploaded by

Copyright:

Available Formats

Introductions To: Deep Foundations

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Introductions To: Deep Foundations

Uploaded by

Copyright:

Available Formats

Introductions to

The types of deep foundations are

Caissons are or well foundations are heavier

CLASSIFICATION W.R.T MODE OF

CLASSIFICATION W.R.T MATERIAL OF

1)Timber piles: (Trunk of a Wooden

CLASSIFICATION W.R.T MATERIAL OF

Some times skin friction is predominant

CLASSIFICATION W.R.T FUNCTION OF

5. Root Pile (Rectangular in Italy) Used

Factors effecting the selection

You might also like