Scribd
Upload
106 views62 pages

Displacement Medthod of Analysis: Moment Distribution

The document discusses the Moment Distribution Method for analyzing structural frames. It describes Hardy Cross's formulation of the method which involves: [1] initially restraining joints from rotating; [2] distributing fixed-end moments at joints to members based on their stiffness; [3] carrying moments over to the other end of each member; and [4] repeating these steps until moments are negligible. The method calculates distribution factors and carry-over factors to determine final member moments. Examples are provided to demonstrate applying the method to beams and frames with and without consideration of sidesway.

Uploaded by

Maier Dorin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
106 views62 pages

Displacement Medthod of Analysis: Moment Distribution

The document discusses the Moment Distribution Method for analyzing structural frames. It describes Hardy Cross's formulation of the method which involves: [1] initially restraining joints from rotating; [2] distributing fixed-end moments at joints to members based on their stiffness; [3] carrying moments over to the other end of each member; and [4] repeating these steps until moments are negligible. The method calculates distribution factors and carry-over factors to determine final member moments. Examples are provided to demonstrate applying the method to beams and frames with and without consideration of sidesway.

Uploaded by

Maier Dorin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 62

DISPLACEMENT

MEDTHOD
OF(KANALYSIS:
Member Stiffness Factor
)

Distribution Factor (DF)


Carry-Over Factor

Distribution of Couple at Node

MOMENT
DISTRIBUTION
Moment Distribution
for Beams

General Beams
Symmetric Beams
Moment Distribution for Frames: No Sidesway
Moment Distribution for Frames: Sidesway

General Principles and Definitions


Thus the Moment Distribution Method (also known as the Cross Method) became
the preferred calculation technique for reinforced concrete structures.
The description of the moment distribution method by Hardy Cross is a little
masterpiece. He wrote: "Moment Distribution. The method of moment
distribution is this:
Imagine all joints in the structure held so that they cannot rotate and compute
the moments at the ends of the members for this condition;
at each joint distribute the unbalanced fixed-end moment among the connecting
members in proportion to the constant for each member defined as "stiffness";
multiply the moment distributed to each member at a joint by the carry-over
factor at the end of the member and set this product at the other end of the
member;
distribute these moments just "carried over";
repeat the process until the moments to be carried over are small enough to be
neglected; and
add all moments - fixed-end moments, distributed moments, moments carried
over - at each end of each member to obtain the true moment at the end."
[Cross 1949:2]

1. Restrain all possible displacements.


2. Calculate Distribution Factors:
The distribution factor DFi of a member connected to any joint J is

where S is the rotational stiffness , and is given by

3. Determine carry-over factors


The carry-over factor to a fixed end is always 0.5, otherwise it is 0.0.
4. Calculate Fixed End Moments. (Table 3.1).
These could be due to in-span loads, temperature variation and/or
relative displacement between the ends of a member.
5. Do distribution cycles for all joints simultaneously
Each cycle consists of two steps:
1. Distribution of out of balance moments Mo,
2.Calculation of the carry over moment at the far end of each member.
The procedure is stopped when, at all joints, the out of balance moment is a
negligible value. In this case, the joints should be balanced and no carry-over
moments are calculated.

6. Calculate the final moment at either end of each member.


This is the sum of all moments (including FEM) computed during the
distribution cycles.

Example

Stiffness-Factor Modification

Example

Symmetric Beam and Loading

Symmetric Beam with


Antisymmetric Loading

Moment Distribution for frames:


No sidesway

Moment Distribution for frames:


sidesway

You might also like