Sand Replacement Method

SAND REPLACEMENT
METHOD
INTRODUCTION OF SAND
REPLACEMENT METHOD
Sand replacement method is to determine the density

of soil in the ground. The basic principle of sand
replacement method is to measure the in situ volume
of hole from which the material was excavated from
the weight of sand with known density filling in the
hole. The in situ density of material is given by the
weight of the excavated material divided by the
in situ volume.
Equipments used in sand

replacement method
Sand cone apparatus which consists of a one gallon plastic bottle with a metal cone attached to it.
One gallon plastic can with cap.
Balance sensitive to 1 g.
Base plate.
Tools for excavating a hole in the ground.
Clean, uniformly graded sand ranging from #20 to #30 sieve such as Ottawa Sand.
Proctor compaction mold without attached extension (used for calibration).
Plastic air tight bag for carrying wet excavated soil from field to the lab.
Metal tray with a hole in the centre.
Oven with temperature kept at about 105 110 o .
Procedure of sand
replacement method
(IS : 2720 PART 28)
(1) Measure the weight of Proctor mold + Base, W1 (Go to row 1 of table).
(2) Fig. (a). Pour the sand into the compaction mold.
Fig. (b). Level the surface (Do not disturb the mold as the sand may rearrange and get compacted).
Fig. (c). Compaction mold filled with sand.
Fig. (d). Measure the weight of Proctor mold + base + sand, W2
(Go to row 2 of table).
(a)
(b)
(c)
(d)
(3) Measure the weight of plastic gallon + cone + sand, W3 (before use) (Go to row 5 of table).
(4) Fig. (a). Close the valve attached to the cone.

Fig. (b). Turn the cone and gallon upside down on the tray.
Fig. (c). Open the valve, sand flows from the gallon to the cone, after the flow stops, close the valve and take the
gallon + cone from the tray.
Fig. (d). Measure the weight of plastic gallon + cone + sand, W4 (after use) (Go to row 6 of table).
(a)
(b)
(c)
(d)
(5) Weight of plastic gallon + cone + sand, W5 (before use) (Go to row 8 of table).
(6) Go to the field where the soil s unit weight is to be measured, place the metal tray and fasten the 4 screws.
(7) Dig up a 10 to 15 cm deep hole.
(8) As you are digging the hole put the retrieved soil into the plastic bag in order that the soil does not lose moisture.
All of the soil including the soft soil at the bottom of the hole is poured into the bag as well.
(9) Having the valve closed turn the gallon + cone upside down and place the cone in the center hole of tray and open
the valve so that sand flows down to the hole.
(10) After flow of sand stops, close the valve and pick the assembly up, the sand in the cone will be poured into the
tray. This sand will be left there in the field. (Notice, the plastic bag should be kept closed while transferring to the
lab to avoid moisture loss and consequently weight of the soil).
(11) Measure the weight of plastic gallon + cone + sand, W6 (after use) (Go to row 9 of table).
(12) Measure the weight the evaporating dish, W7 (Go to row 11 of table).
(13) Measure the weight the evaporating dish + wet soil from the field, W8 (Go to row 12 of table).
(14) Put the evaporating dish + wet soil in the oven and after 24 hours weight it again, W 9
(Go to row 13 of table).
(15) Having the information you got so far in the table, calculations can be carried out easily. Do the calculations, fill out
the table and include the answers to the following questions in your reports.
THE EXAMPLE OF THE RESULTS FOR

SAND REPLACEMENT METHOD
Conversion factors (Unit weight):
1000 kg/m3 = 9.81 KN/m3 = 62.4
lb/ft3
Test Steps
Quantity
Obtaining the unit weight of the sand used

1) Weight of Proctor mold + Base, W1
4.178 kg
2) Weight of proctor mold + Base + Sand, W2
5.609 kg
3) Volume of the mold, V1
0.00095 m3
4) Dry unit weight, d (sand) = (W2 - W1) / V1
1506 kg/m3
Calibration cone
5) Weight of plastic Gallon+Cone+Sand (before use), W3
5.466 kg
6) Weight of plastic Gallon+Cone+Sand (after use), W4
3.755 kg
7) Weight of the sand to fill the cone, Wc = W3- W4
1.711 kg
Test Steps
Quantity
Results from field tests

8) Weight of plastic Gallon+Cone+Sand (before use), W5
7.387 kg
9) Weight of plastic Gallon+Cone+Sand (after use), W6
3.919 kg
10) Volume of hole, V2 = (W5-W6-Wc)/ d (sand)
0.00117m3
11) Weight of evaporating dish, W7

12. Weight of evaporating dish + wet soil from the field, W8
0.507 kg
2.334 kg
13. Weight of evaporating dish + dry soil after 24hrs, W9
2.251 kg
14. Moist unit weight of the soil in the field, t (in-situ soil) = (W8 W7) / V2
15. Water content in the field, w(%)= (W8 - W9) / (W9- W7)*100
1561 kg/m3
16. Dry unit weight in the field, d (in-situ soil)= [t (Row 14)] /
[1+ w(%) / 100]
1490 kg/m3
4.76%
THE PICTURES OF SAND

REPLACEMENT METHOD

Sand Replacement Method

Uploaded by

Copyright:

Available Formats

Sand Replacement Method

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sand Replacement Method

Uploaded by

Copyright:

Available Formats

What is the basic principle of sand replacement method?

What is the basic principle of sand replacement method?

What equipment is used in sand replacement method?

What equipment is used in sand replacement method?

SAND REPLACEMENT

Sand replacement method is to determine the density

Equipments used in sand

(4) Fig. (a). Close the valve attached to the cone.

(7) Dig up a 10 to 15 cm deep hole.

THE EXAMPLE OF THE RESULTS FOR

Obtaining the unit weight of the sand used

2) Weight of proctor mold + Base + Sand, W2

3) Volume of the mold, V1

4) Dry unit weight, d (sand) = (W2 - W1) / V1

6) Weight of plastic Gallon+Cone+Sand (after use), W4

7) Weight of the sand to fill the cone, Wc = W3- W4

Results from field tests

9) Weight of plastic Gallon+Cone+Sand (after use), W6

10) Volume of hole, V2 = (W5-W6-Wc)/ d (sand)

11) Weight of evaporating dish, W7

13. Weight of evaporating dish + dry soil after 24hrs, W9

THE PICTURES OF SAND

You might also like