1 Batching of Aggregates For Concrete
1 Batching of Aggregates For Concrete
1 Batching of Aggregates For Concrete
Concrete
Fine Aggregate
Sand and/or crushed
stone
< 5 mm (0.2 in.)
F.A. content usually
35% to 45% by mass
or volume of total
aggregate
Coarse Aggregate
Gravel and
crushed stone
5 mm (0.2 in.)
typically
between 9.5
and 37.5 mm
(3/8 and 1 in.)
Rock and Mineral Constituents
in Aggregates
1. Minerals
2. Igneous rocks
3. Metamorphic rocks
4. Sedimentary rocks
Rock and Mineral
Constituents in Aggregates
Silica
Quartz, Opal
Silicates
Feldspar, Clay
Carbonate
Calcite,
Dolomite
1. Minerals
Rock and Mineral
Constituents in Aggregates
Sulfate
Gypsum, Anhydrite
Iron sulfide
Pyrite, Marcasite
Iron oxide
Magnetite, Hematite
1. Minerals
Rock and Mineral Constituents
in Aggregates
Granite
Syenite
Diorite
Gabbro
Peridotite
Pegmatite
Volcanic
glass
Felsite
Basalt
2. Igneous rocks
Rock and Mineral
Constituents in Aggregates
Conglomerate
Sandstone
Claystone, siltstone,
argillite, and shale
Carbonates
Chert
3. Sedimentary rocks
Rock and Mineral
Constituents in Aggregates
Marble
Metaquartzite
Slate
Phyllite
Schist
4. Metamorphic rocks
Amphibolite
Hornfels
Gneiss
Serpentinite
Normal-Weight Aggregate
Most common aggregates
Sand
Gravel
Crushed stone
ASTM C 33
Produce normal-weight concrete
2200 to 2400 kg/m
3
(140 to 150 lb/ft
3
)
Lightweight Aggregate (1)
Expanded
Shale
Clay
Slate
Slag
ASTM C 330
Produce structural lightweight concrete
1350 to 1850 kg/m
3
(90 to 120 lb/ft
3
)
Lightweight Aggregate (2)
Pumice
Scoria
Perlite
Vermiculite
Diatomite
Produce lightweight insulating
concrete 250 to 1450 kg/m
3
(15 to 90 lb/ft
3
)
Heavyweight Aggregate
Barite
Limonite
Magnetite
Ilmenite
Hematite
Iron
Steel punchings or shot
ASTM C 637, C 638 (Radiation Shielding)
Produce high-density concrete up
to 6400 kg/m
3
(400 lb/ft
3
)
Aggregate Characteristics and Tests (1)
Characteristic Test
Abrasion resistance ASTM C 131 (AASHTO T 96), ASTM C 535, ASTM C 779
Freeze-thaw
resistance
ASTM C 666 (AASHTO T 161), ASTM C 682,
AASHTO T 103
Sulfate resistance ASTM C 88 (AASHTO T 104)
Particle shape and
surface texture
ASTM C 295, ASTM D 3398
Grading
ASTM C 117 (AASHTO T 11), ASTM C 136 (AASHTO T
27)
Fine aggregate
degradation
ASTM C 1137
Void content ASTM C 1252 (AASHTO T 304)
Bulk density ASTM C 29 (AASHTO T 19)
Aggregate Characteristics and Tests (2)
Characteristic Test
Relative density
ASTM C 127 (AASHTO T 85)fine aggregate
ASTM C 128 (AASHTO T 84)coarse aggregate
Absorption and
surface moisture
ASTM C 70, ASTM C 127 (AASHTO T 85), ASTM C 128
(AASHTO T 84), ASTM C 566 (AASHTO T 255)
Strength ASTM C 39 (AASHTO T 22), ASTM C 78 (AASHTO T 97)
Def. of constituents ASTM C 125, ASTM C 294
Aggregate
constituents
ASTM C 40 (AASHTO T 21), ASTM C 87 (AASHTO T 71),
ASTM C 117 (AASHTO T 11), ASTM C 123 (AASHTO T
113), ASTM C 142 (AASHTO T 112), ASTM C 295
Alkali Resistance
ASTM C 227, ASTM C 289, ASTM C 295, ASTM C 342, ASTM C
586, ASTM C 1260 (AASHTO T 303), ASTM C 1293
Grading of Aggregate
Grading is the particle-size distribution of
an aggregate as determined by a sieve
analysis using wire mesh sieves with square
openings.
ASTM C 33
Fine aggregate7 standard sieves with
openings from 150 m to 9.5 mm
(No. 100 to 3/8 in.)
Coarse aggregate13 sieves with openings
from 1.18 mm to 100 mm
(0.046 in. to 4 in.)
Range of Particle Sizes
Fine-Aggregate Grading Limits
Sieve size Percent passing by mass
9.5 mm (3/8 in.) 100
4.75 mm (No. 4) 95 to 100
2.36 mm (No. 8) 80 to 100
1.18 mm (No. 16) 50 to 85
600 m (No. 30) 25 to 60
300 m (No. 50) 5 to 30 (AASHTO 10 to 30)
150 m (No. 100) 0 to 10 (AASHTO 2 to 10)
Maximum Size vs. Nominal
Maximum Size of Aggregate
Maximum size is the smallest sieve
that all of a particular aggregate must
pass through.
Nominal maximum size is the
standard sieve opening immediately
smaller than the smallest through which
all of the aggregate must pass.
The nominal maximum-size sieve may
retain 5% to 15%
Coarse Aggregate Grading
Sieve size
Percent passing
by mass
37.5 mm (1 in.) 100
25.0 mm (1 in.) 95 to 100
12.5 mm ( in.) 25 to 60
4.75 mm (No. 4) 0 to 10
2.36 mm (No. 8) 0 to 5
Size No. 57
25 to 4.75 mm [1 in. to No. 4]
Autograder
Grading Limits
Combined Aggregate Grading
Reduction of Voids
Dispersion of Aggregates
Fineness modulus (FM)
Defined as an empirical figure obtained by adding the total
percentage of the sample of an aggregate retained on each
of a specified series of sieves, and dividing the sum by 100.
The sieve sizes are 150, 300, 600, 1.18 mm, 2.36 mm,
4.75 mm, 9.5 mm, 19.0 mm, 38.1 mm and larger increasing
in the ratio of 2:1.
The same value of fineness modulus may be obtained from
several different particle size distributions.
In general however a smaller value indicates a finer
aggregate and higher value a coarser aggregate. Fine
aggregates range from a FM of 2.00 to 4.00, and coarse
aggregates smaller than 38.1 mm range from 6.50 to 8.00.
Combinations of fine and coarse aggregates have
intermediate values.
Sieve Analysis and FM of Sand
Sieve size
Percentage of
individual fraction
retained, by mass
Percentage
passing,
by mass
Cumulative
percentage re-
tained, by mass
9.5 mm (3/8 in.) 0 100 0
4.75 mm (No. 4) 2 98 2
2.36 mm (No. 8) 13 85 15
1.18 mm (No. 16) 20 65 35
600 m (No. 30) 20 45 55
300 m (No. 50) 24 21 79
150 m (No. 100) 18 3 97
Pan 3 0
Total 100 283
Fineness modulus = 283 100 = 2.83
Maximum Aggregate Size and
Water Requirement
Maximum Aggregate Size and
Cement Requirement
Moisture Conditions
Bulking of Sand
D-Cracking
Drying Shrinkage
Harmful Materials (1)
Substances Effect on concrete Test designation
Organic
impurities
Affects setting and
hardening, may
cause deterioration
ASTM C 40
ASTM C 87
(AASHTO T 21)
(AASHTO T 71)
Materials finer
than the 75-m
(No. 200) sieve
Affects bond,
increases water
requirement
ASTM C 117 (AASHTO T 11)
Coal, lignite, or
other lightweight
materials
Affects durability,
may cause stains
and popouts
ASTM C 123 (AASHTO T 113)
Soft particles Affects durability ASTM C 235
Harmful Materials (2)
Substances Effect on concrete Test designation
Clay lumps and
friable
particles
Affects workability
and durability, may
cause popouts
ASTM C 142 (AASHTO T 112)
Chert of less
than 2.40
relative density
Affects durability,
may cause popouts
ASTM C 123
ASTM C 295
(AASHTO T 113)
Alkali-reactive
aggregates
Causes abnormal
expansion, map
cracking, and
popouts
ASTM C 227,
C 289, C 295,
C 342, C 586
C 1260, C 1293
(AASHTO T 303)
Harmful Reactive Substances
Alkali-silica reactive substances
Alkali-carbonate
reactive substances
Andesites
Argillites
Certain
siliceous
limestones
and dolomites
Chalcedonic
cherts
Chalcedony
Cristobalite
Dacites
Glassy or
crypto-
crystalline
volcanics
Granite gneiss
Graywackes
Metagray-
wackes
Opal
Opaline shales
Phylites
Quartzites
Quartzoses
Cherts
Rhyolites
Schists
Siliceous shales
Strained quartz
and certain other
forms of quartz
Synthetic and
natural silicious
glass
Tridymite
Calcitic dolomites
Dolomitic limestones
Fine-grained dolomites
Popouts
Iron Particles in Aggregates
Alkali- Aggregate
Reactivity ( AAR )
is a reaction between the active
mineral constituents of some
aggregates and the sodium and
potassium alkali hydroxides and
calcium hydroxide in the concrete.
Alkali-Silica Reaction (ASR)
Alkali-Carbonate Reaction (ACR )
Alkali-Silica Reaction (ASR)
Visual Symptoms
Network of cracks
Closed or spalled joints
Relative displacements
Visual Symptoms
(cont.)
Fragments breaking out of the
surface (popouts)
Mechanism
1. Alkali hydroxide + reactive
silica gel reaction
product (alkali-silica gel)
2. Gel reaction product +
moisture expansion
Alkali-Silica Reaction (ASR)
Influencing Factors
Reactive forms of silica in
the aggregate,
High-alkali (pH) pore
solution
Sufficient moisture
If one of these conditions is
absent ASR cannot occur.
Alkali-Silica Reaction (ASR)
Test Methods
Mortar-Bar Method
(ASTM 227)
Chemical Method
(ASTM C 289)
Petrographic Examination
(ASTM C 295)
Rapid Mortar-Bar Test
(ASTM C 1260 or AASHTO T 303)
Concrete Prism Test
(ASTM C 1293 )
Alkali-Silica Reaction (ASR)
Controlling ASR
Non-reactive aggregates
Supplementary cementing materials
or blended cements
Limit alkali loading
Lithium-based admixtures
Limestone sweetening (~30%
replacement of reactive aggregate
with crushed limestone
Alkali-Silica Reaction (ASR)
Effect of Supplementary
Cementing Materials on ASR
Alkali-Carbonate Reaction (ACR)
Influencing factors
Clay content, or insoluble residue
content, in the range of 5% to 25%
Calcite-to-dolomite ratio of
approximately 1:1
Increase in the dolomite volume
Small size of the discrete dolomite
crystals (rhombs) suspended in a
clay matrix
Alkali-Carbonate Reaction
Test methods
Petrographic examination
(ASTM C 295)
Rock cylinder method (ASTM C
586)
Concrete prism test (ASTM C
1105)
Alkali-Carbonate Reaction
Controlling ACR
Selective quarrying to avoid reactive
aggregate
Blend aggregate according to
Appendix in ASTM C 1105
Limit aggregate size to smallest
practical
Handling and Storing
Aggregates
Recycled-Concrete
Aggregate