Scribd
Upload
233 views12 pages

Project

This document describes an automatic temperature controller project using a microcontroller. The system uses an AT89C52 microcontroller and DS1621 temperature sensor chip to sense the temperature and display it on an LCD module. The temperature sensor measures and converts the temperature to a digital output. The microcontroller program is written in assembly language. The system can monitor the temperature of components like a running motor and display if it exceeds safe levels to prevent overheating damage. It implements an embedded system using microcontroller programming in assembly language to operate the hardware through software.

Uploaded by

ppksn
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
233 views12 pages

Project

This document describes an automatic temperature controller project using a microcontroller. The system uses an AT89C52 microcontroller and DS1621 temperature sensor chip to sense the temperature and display it on an LCD module. The temperature sensor measures and converts the temperature to a digital output. The microcontroller program is written in assembly language. The system can monitor the temperature of components like a running motor and display if it exceeds safe levels to prevent overheating damage. It implements an embedded system using microcontroller programming in assembly language to operate the hardware through software.

Uploaded by

ppksn
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 12

•

AUTOMATIC
• TEMPERATURE
• CONTROLLER
• BY
INTODUCTION

1.This project is basically a


microcontroller based
temperature indicator system .
COMPONENTS USED
In this project we use the Atmel series

micro- controller, the AT89C52, which


belongs to the same family of AT89C52.
The system also uses a temperature
sensor chip, the DS1621 which acts as
a sensor as well as functions as an
analog to digital converter. The DS1621
chip senses the temperature and
converts it into a digital output. The
output is displayed on a LCD module.
The program for the microcontroller is
written in assembly language.
PIN DIAGRAM

AT89C52
AIM
• To measure and display the
temperature of the most temperature
sensitive regions, such as a running
DC motor. If the motor runs
excessively the temperature raises to
a level enough to damage the coil of
the motor. At that time if the circuit is
placed over the surface of the motor
the system displays the temperature
and if necessary it can also if the
temperature is crossing a danger
level by displaying a “high”
programmed in the microcontroller.
Similarly, a “low” can also be
TECHNOLOGY USED

• This automatic temperature


controller using serial
communication is based on
embedded system in which we
operate our hardware through the
software by using programming in
assembly language. This is burn in
to microcontroller 89C51.
•
COMPONENTS USED
• IC’s used:-
– IC1- 7805 Voltage Regulator
– IC2- AT89c52 microcontroller
– IC3- DS1621 temperature sensor
– IC4- MAX 232
• Resistors:-
• R1 1 kilo-ohm
• R2 47 kilo-ohm
• R3 10 kilo-ohm
• R4,R5 4.7 kilo-ohm
• Vr1 1 kilo-ohm

COMPONENTS USED
• Capacitors:-
• C1 470uF, 25V electrolytic capacitor
• C2, C3, C4 0.1 uF ceramic disk
• C5 10uF, 16V electrolytic capacitor
• C6, C7 33pF ceramic capacitor
• Other components used:-
– Transformer 230 ac primary to 0- 9V, 250
mA secondary
– Crystal 12 MHz
– LCD 16*2 LCD module
– Diodes IN-4007
– RS 232 serial port

FABRICATION TOOLS
 

• Permanent Marker
• Etching Reagent
• Drilling machine
• Cutter
• Solder iron

MAJOR APPLICATIONS

• In industry purpose
• Production field
• Research centre
• To measure temperature of volcano

THANK YOU

You might also like