OTF101202 OptiX RTN 600 Routine Maintenance ISSUE 1.02

www.huawei.
com
Copyright 2006 Huawei Technologies Co., Ltd. All rights reserved.
OptiX RTN 600
Routine Maintenance
Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved. Page2
References
Routine Maintenance Guide and Common Maintenance
Operation Guide in the OptiX RTN 600 Radio Transmission
System Maintenance Guide.
Objectives
Upon completion of this course, you will be able to:
List the routine maintenance items of OptiX RTN 600
Implement the maintenance operation of OptiX RTN 600
Judge the common faulty in OptiX RTN 600
Contents
1. Routine Maintenance
2. Common Maintenance Operations
Contents
1.1 IDU maintenance items
1.2 Out door units maintenance items
1.3 Maintenance Items on NM system

Observing The Indicators
SRV indicator on all boards: indicates status of services
Red color: critical or major alarm
Yellow color: minor or remote alarm
Green color: no alarm
Off: no service configured or power off
STAT indicator on all boards: indicates status of the boards
Green color: board running normally
Red color: board has hardware fault
Off: board not running, not be created in NMS or power off
Observing The Indicators (cont.)
BER indicator on IF board: indicates bit errors on microwave
Yellow color: bit errors exceed the threshold
Off: bit error is ok
ODU indicator on IF board: indicates status of the ODU
Green color: ODU running normally
Red color: ODU has hardware fault
Link indicator on IF board: indicates status of MW link
Green color: MW link is normal
Red color: MW link is abnormal
Testing The Orderwire Phone
Making a call to other site.
The dial tone should be clear after pick up the phone.
The ringing tone should be clear after dial the number.
If remote site answered the call, the voice should be
clear without noise.
Cleaning the Air Filter
It is recommend to clean the
air filter once every two
months.
Cleaning the air filter is
necessary only for the IDU
620 that is configured with
fans.
Cleaning the Equipment Room
It is recommend to clean the equipment room once every
two months.
1. Temperature: 5 to 45.
2. Humidity: 5% to 95%.
3. Disaster protection.
4. Clean the equipment room.
Contents

ODU Maintenance Items
It is recommend to perform the operations in every half year
or after a fresh gale.
Checking the ODU
Checking the hybrid coupler
Checking the antenna
Checking the IF cable
Checking the ODU
Protection area of the
lightning arrester.
Connections between ODU
to hybrid coupler and
antenna.
Water-proof checking for the
interfaces.
Status of protection
grounding cable.
Surface of ODU.
Checking the Hybrid Coupler
Protection area of the lightning arrester.
Connections between hybrid coupler to ODU and antenna.
Water-proof checking for the interfaces.
Checking the Antenna
Protection area of the lightning
arrester.
Connections between antenna to
pole.
Antenna radome should be intact.
Water accumulation in antenna.
Position and direction of antenna.
Checking the IF Cable
Appearance of the IF cable.
Cable connectors.
Cable grounding.
Contents

Maintenance Via LCT or NMS
When the T2000 Web LCT is available on site or equipment
is managed by T2000:
Querying alarms
Querying performance
Querying abnormal events
Querying the receiving power of the ODU
Testing protection functions once every half year
Summary
IDU maintenance items
Observing the indicators in IDU
Testing the orderwire phone
Cleaning the air filter
Cleaning the equipment room
ODU maintenance items
Observing the indicators in IDU
Testing the orderwire phone
Cleaning the air filter
Cleaning the equipment room
Maintenance operations via LCT and NMS: alarm,
performance, power querying
Contents
2. Common Maintenance Operations
Replacing an ODU
ODU power off.
Disconnect cable.
Uninstall ODU.
Install the new ODU.
New ODU consistent with the previous one.
Polarity.
Connect back the cables.
Carry out the waterproof measures for the IF interface of the
ODU.
Turn on the ODU-PWR switch on the panel of the IF board.
Check status of new ODU by Web LCT.
Plugging Out a Board
Step 1:
Loosen the screws
on the front panel.
Step 2:
Unlock the ejector levers of the
board so that the board is
disconnected from the backplane.
Step 3:
Draw out the board
along the guiding rail.
Plugging In a Board
Step 1:
Slowly inserting the board
along the guiding rail.
Step 2:
Lock the ejector levers
of the board.
Step 3:
Fasten the screws
on the front panel.
Replacing an IF Board
Active/standby board switch or SNCP switch.
ODU power off and IF cable disconnect.
Replace the new IF board and connect IF cable.
Observe the indicators.
Turn on ODU power.
Restore active/standby board or SNCP service.
Monitor status of the new IF board.
Replacing an SCC Board
Remove the SCC board and
make sure the spare SCC
board is consistent with it.
Replace the removable
memory card on spare SCC.
Install the spare board.
Monitor the indicators, and
check the status of the
running SCC board by Web
LCT.
Abbreviations and Acronyms
IDU In Door Unit
ODU Out Door Unit
BER Bit Error Rate
IF Intermediate Frequency
NMS Network Management System
SNCP Sub-Network Connection Protection
LCT Local Craft Terminal
SCC System Control and Communication Unit
Summary
Routine maintenance operations of the OptiX RTN 600,
including:
Replacing an ODU
Precautions for replacing a board
Replacing an IF board
Replacing an SCC board
Thank you
www.huawei.com

OTF101202 OptiX RTN 600 Routine Maintenance ISSUE 1.02

Uploaded by

Copyright:

Available Formats

OTF101202 OptiX RTN 600 Routine Maintenance ISSUE 1.02

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

OTF101202 OptiX RTN 600 Routine Maintenance ISSUE 1.02

Uploaded by

Copyright:

Available Formats

www.huawei.

You might also like