Scribd
Upload
107 views21 pages

Lect#5

There are several types of breakdown that can occur in solid dielectrics over prolonged use beyond intrinsic or thermal breakdown. These include chemical/electrochemical breakdown from oxidation, hydrolysis, or other chemical reactions; breakdown from treeing and tracking where conductive paths form on the dielectric surface; and breakdown from internal discharges in voids within the material. Treeing occurs as spark channels branch through the insulation, while tracking is the formation of a surface conductive path. Internal discharges in voids can exceed the void's breakdown voltage and cause erosion over time leading to complete breakdown.

Uploaded by

amrit403
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
107 views21 pages

Lect#5

There are several types of breakdown that can occur in solid dielectrics over prolonged use beyond intrinsic or thermal breakdown. These include chemical/electrochemical breakdown from oxidation, hydrolysis, or other chemical reactions; breakdown from treeing and tracking where conductive paths form on the dielectric surface; and breakdown from internal discharges in voids within the material. Treeing occurs as spark channels branch through the insulation, while tracking is the formation of a surface conductive path. Internal discharges in voids can exceed the void's breakdown voltage and cause erosion over time leading to complete breakdown.

Uploaded by

amrit403
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 21

Breakdown of Solid Dielectrics in practice

There are certain types of breakdown which do not come under either intrinsic breakdown or thermal breakdown , but actually occur after prolonged operation They are
Chemical & Electrochemical breakdown Breakdown due to treeing and Tracking Breakdown down due to internal discharges
1

Chemical & electrochemical breakdown


In the presence of air & other gases, some dielectric materials undergo chemical changes when subjected to continuous electrical stresses Some important chemical reactions that occur are
Oxidation Hydrolysis Chemical Action
2

Oxidation
In the presence of air or oxygen, materials such as rubber and polyethylene undergo oxidation giving rise to surface cracks.

Hydrolysis
When moisture or water vapour is present on the surface of a solid dielectrics, hydrolysis occurs and the material lose their electrical and mechanical properties. Electrical properties of material such as paper, cotton tape and cellulose materials deteriorate very rapidly due to hydrolysis. Plastic like polyethylene undergo changes and their service life considerably reduces.
4

Chemical Action
Even in the absence of electric fields progressive chemical degradation of insulating materials can occur due to a variety of process such as chemical instability at high temperature, oxidation and cracking in the presence of air and ozone and hydrolysis due to moisture and heat. Since different insulating materials come into contact with each other in many practical apparatus , chemical reactions occur between these various materials leading to reduction in electrical and mechanical strength resulting in failure. The chemical and electrochemical deterioration increases very rapidly with temperature and hence temperatures should be avoided 5

Breakdown due to treeing & tracking


Polymeric insulation is widely used for many engineering applications because they are tough, light in weight , possess excellent dielectric properties, ca be easily fabricated in any complicated shape as required in practical use. However , their life when used in high voltage systems gets severely reduced by the degradation process. When a solid dielectric subjected to electrical stresses for a long time , normally two kinds of visible markings are observed on the dielectric materials They are
- Presence of a conducting path across the surface of the insulation. - Leakage current passing through the conducting path which leads to the formation of spark
6

Breakdown due to treeing & tracking


Insulation deterioration occurs as a result of these sparks. The spreading of a spark channels in the form of branches of a tree is called treeing. Tracking is the formation of a conducting path across the surface of the insulation mainly due to surface erosion under voltage application. While in use, insulator progressively gets coated with moisture that causes increased conduction leading to the formation of surface tracks.
7

Breakdown due to treeing & tracking


Consider a system of a solid dielectric having a conducting film and two electrodes on its surface. In practice , the conducting film very often is formed due to moisture. On application of voltage , the film starts conducting , resulting in generation of heat and surface starts becoming dry. The conducting film becomes separate due to drying and so sparks are drawn damaging the dielectric surface. With organic insulating materials such as paper and Bakelite , the dielectric carbonizes at the region of sparking and the carbonized region act as permanent conducting channels resulting in increased stress over the rest of the region.
8

Breakdown due to treeing & tracking


This is cumulative process and insulation failure occurs when carbonized tracks bridge the distance between the electrodes. This phenomenon called tracking and is common between layers of Bakelite , paper and similar dielectrics built of laminations. On the other hand treeing occurs due to the erosion of material at the tips of the spark. Erosion results in the roughening of the surfaces and hence becomes a source of dirt and contamination. This causes increased conductivity resulting either in the formation of a conducting path bridging the electrodes or in mechanical failure of the dielectrics.
9

Breakdown due to treeing & tracking


When a dielectric material lies between two electrodes as shown in figure , there is a possibility for two different dielectric media , the air and dielectric to come in series. The voltage across the two media are as shown (V1 across the air gap and V2 across the dielectric.)

10

Breakdown due to treeing & tracking


The voltage V1 across the air gap is given by

Where V is the applied voltage

1= Dielectric of Solid
0 = Dielectric air

Since 2> 1 , most of the voltage appears across the air gap.

Sparking will occur in the air gap and charge accumulation takes place on the surface of the insulation
Sometimes the spark erodes the surface of the insulation.
11

Breakdown due to treeing & tracking


As time passes , breakdown channels spreads through the insulation in an irregular tree like fashion leading to the formation of conducting channels. This kind of channeling is called treeing. Under ac voltage conditions treeing can occur in a few minutes or several hours. Treeing can be prevented by having clean , dry and undamaged surfaces and a clean environment. 12

Breakdown due to treeing & tracking


The materials chosen should be able to resist tracking Sometimes moisture repellant greases are used. But this needs frequent cleaning and regreasing. increasing the creepage distances should prevent tracking , but in practice the presence of moisture films defeats the purpose.
13

Breakdown due to internal discharge


Solid insulating materials contain void or cavities within the medium or at the boundaries between the dielectric and the electrodes. These voids have lower dielectric strength as compared to the material. Hence the electric field strength in the voids is higher than across the dielectric . Therefore ,even under normal working voltages the field in the voids may exceed their breakdown value and breakdown may occur.
14

Breakdown due to internal discharge


Let us consider a dielectric between two conductors as shown in figure.

C1 represents the capacitance of the void or cavity, C2 is the capacitance of the dielectric which is in series with the void and C3 is the capacitance 15 of the rest of the dielectric.

Breakdown due to internal discharge


When the applied Voltage is V, the voltage across the void is given by

Where d1 & d2 are the thickness of the void and the dielectric respectively having permittiivties o & 1

Usually d1<< d2 and if we assume that the cavity

is filled with a gas


Here r is the relative permittivity of the dielectric
16

Breakdown due to internal discharge


When a voltage is applied ,V1 reaches the breakdown strength of the medium in the cavity (Vi) and breakdown occurs. Vi is called the discharge inception voltage. Vi & V1 are same for breakdown. Hence V1 can be taken as internal discharge voltage. These internal discharges will have the same effect as treeing on the insulation They will have sufficient energy and when they reach the void surfaces they may break the chemical bonds.
17

Breakdown due to internal discharge


In each discharges there will be some heat dissipated in the cavities and this will carbonize the surface of the voids and will cause erosion of the material. Channels & pits formed on the cavity surfaces increase the conduction. Chemical degradation may occur as a result of the active discharge products formed during breakdown,
18

Breakdown due to internal discharge


All these effects will result in a gradual erosion of the material and consequent reduction in the thickness of insulation leading to breakdown. The life of insulation with internal discharges depends upon the applied voltage and the number of discharges. Breakdown by this process may occur in a few days or may take a few years.
19

Example
A solid dielectric specimen of dielectric constant of 4.0 shown in figure has an internal void if thickness 1mm. The specimen is 1 cm thick and is subjected to a voltage of 80KV (rms). If the void is filled with air and if the breakdown strength of air can be taken as 30KV(peak)/cm, find the voltage at which internal discharge can occur.

The Voltage drop appearing across the void is given by

20

Example (contd)
d1= 1 mm, d2= 9 mm o = 8.89*10-12 F/m 1 = r o = 4.0o V1= V*1/(1+9/4) =4V/13 The voltage at which the air void of 1mm thickness breaks down is 3 KV/mm *1 = 3KV V1 = 3KV So, V= 13 V1/4 = 13*3/4 = 39/4= 9.75 (peak) The internal discharge appears in the sinusoidal voltage 80 2 Sinwt when the voltage reaches a value of 9.75KV
21

You might also like