Previous Lecture 31 The Source Free Parallel RLC Circuit

Lecture 32
Example related to Source free Parallel RLC circuit
Example Find v(t) for t > 0 in the RLC circuit of following Fig.

Example
Find v(t) for t > 0 in the RLC circuit of following Fig.

Example
Find v(t) for t > 0 in the RLC circuit of following Fig.

Example
Find v(t) for t > 0 in the RLC circuit of following Fig.

Example
Find v(t) for t > 0 in the RLC circuit of following Fig.

Example
Find v(t) for t > 0 in the RLC circuit of following Fig.

Step Response of a Series RLC Circuit

Thus, the complete solutions for the overdamped, underdamped, and critically damped cases are:

The values of the constants A1 and A2 are obtained from the initial conditions: v(0) and dv(0)/dt . Keep in mind that v and i are, respectively, the voltage across the capacitor and the current through the inductor. Therefore, the above Eq. only applies for finding v. But once the capacitor voltage vC = v is known, we can determine i = C dv/dt, which is the same current through the capacitor, inductor, and resistor. Hence, the voltage across the resistor is vR = iR, while the inductor voltage is vL = L di/dt.

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Example For the circuit in Fig., find v(t) and i(t) for t > 0. Consider these cases: R = 5 ,R = 4 , andR = 1 .

Figure plots the responses for the three cases. From this figure, we observe that the critically damped response approaches the step input of 24 V the fastest.

Response for three degrees of damping

Step Response of a Parallel RLC Circuit

Thus, the complete solutions for the overdamped, underdamped, and critically damped cases are:

The constants A1 and A2 in each case can be determined from the initial conditions for i and di/dt . Again, we should keep in mind that above Eq. only applies for finding the inductor current i. But once the inductor current iL = i is known, we can find v = L di/dt, which is the same voltage across inductor, capacitor, and resistor. Hence, the current through the resistor is iR = v/R, while the capacitor current is iC = C dv/dt.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Example
In the circuit in the following Fig., find i(t) and iR(t) for t > 0.

Material of the Course ECA-1 (EEE121)

Principles of Electric Circuits By FLOYD (Chapter 1 to Chapter 9) Basic Engineering Circuit Analysis By J. David Irwin & R Mark Nelms (Chapter 6 to Chapter 8)

8th Edition

8th Edition

Sr. No.
1 2 3 4 5

Main Topics covered during this course

6
7 8 9 10 11

Parallel Circuits
Series-Parallel Circuits Circuit Theorems and Conversions Branch, Loop, and Node Analyses Capacitors , Inductors RL, RC, and RLC Circuits

Good Luck