100% found this document useful (1 vote)
221 views20 pages

Feedback and Feedforward Control Systems

This document discusses feedback and feedforward control systems. Feedback control systems use measurements of the controlled output to determine corrective action, while feedforward systems use measurements of disturbances before errors occur. The document explains that feedback has advantages like versatility but can be slow, while feedforward is useful for processes with long delays but requires disturbance measurement. It provides an example of using both feedback and feedforward control for liquid level in a boiler drum. Ratio control is also discussed as a type of feedforward control used to maintain the ratio of process variables like flow rates.

Uploaded by

sunilkumar5078
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
221 views20 pages

Feedback and Feedforward Control Systems

This document discusses feedback and feedforward control systems. Feedback control systems use measurements of the controlled output to determine corrective action, while feedforward systems use measurements of disturbances before errors occur. The document explains that feedback has advantages like versatility but can be slow, while feedforward is useful for processes with long delays but requires disturbance measurement. It provides an example of using both feedback and feedforward control for liquid level in a boiler drum. Ratio control is also discussed as a type of feedforward control used to maintain the ratio of process variables like flow rates.

Uploaded by

sunilkumar5078
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 20

Control systems

FEEDBACK AND FEEDFORWARD CONTROL SYSTEMS

Control system definition

A control system is a device, or set of devices to manage, command, direct or regulate the behaviour of other device(s) or system(s)

There are two common classes of control systems, with many variations and combinations: logic or sequential controls, and feedback or linear controls. There is also fuzzy logic, which attempts to combine some of the design simplicity of logic with the utility of linear control.

Block diagrams

Feed back control

Advantages

Corrective action taken regardless of disturbance source


Minimal process information required for controller design PID control is very versatile and usually effective Corrective action not taken until after the output has deviated from the setpoint Requires measurement of the controlled output Does not allows measured disturbances to be utilized Problematic for processes with large time constants and/or long time delays

Disadvantages

Feedforward control

Major disturbance is measured and used as the controller input Advantage

Corrective action can be taken before the output has deviated from the setpoint Particularly useful for processes with large time constants and/or long time delays

Disadvantages

Disturbance must be measured


Provides no advantages for other disturbances Typically requires a process model

Stirred Tank example

Figure 15.2 The feedback control of the liquid level in a boiler drum.

Figure 15.3 The feedforward control of the liquid level in a boiler drum.

Description

A boiler drum with a conventional feedback control system is shown in Fig. 15.2. The level of the boiling liquid is measured and used to adjust the feedwater flow rate. This control system tends to be quite sensitive to rapid changes in the disturbance variable, steam flow rate, as a result of the small liquid capacity of the boiler drum. Rapid disturbance changes can occur as a result of steam demands made by downstream processing units.

Figure 15.4 The feedfoward-feedback control of the boiler drum level.

10

DESCRIPTION

In practical applications, feedforward control is normally used in combination with feedback control. Feedforward control is used to reduce the effects of measurable disturbances, while feedback trim compensates for inaccuracies in the process model, measurement error, and unmeasured disturbances.

Ratio Control

Ratio control is a special type of feedforward control that has had widespread application in the process industries. The objective is to maintain the ratio of two process variables as a specified value. The two variables are usually flow rates, a manipulated variable u, and a disturbance variable d.

u R d

(15-1)

Typical applications of ratio control include: 1.Setting the relative amounts of components in blending operations 2.Maintaining a stoichiometric ratio of reactants to a reactor 3.Keeping a specified reflux ratio for a distillation column 4.Holding the fuel-air ratio to a furnace at the optimum value.
13

Figure 15.5 Ratio control, Method I.

14

The main advantage of Method I is that the actual ratio R is calculated. A key disadvantage is that a divider element must be included in the loop, and this element makes the process gain vary in a nonlinear fashion. From Eq. 15-1, the process gain

1 R Kp u d d

(15-2)

is inversely related to the disturbance flow rate . Because of this significant disadvantage, the preferred scheme for implementing ratio control is Method II, which is shown in Fig. 15.6.

15

Figure 15.6 Ratio control, Method II

16

Regardless of how ratio control is implemented, the process variables must be scaled appropriately. For example, in Method II the gain setting for the ratio station Kd must take into account the spans of the two flow transmitters. Thus, the correct gain for the ratio station is
where Rd is the desired ratio, Su and Sd are the spans of the flow transmitters for the manipulated and disturbance streams, respectively.

Sd K R Rd Su

(15-3)
17

Disturbance Rejection

0.6

0.2 0 Feedback Feedback-Feedforward

0.5

Feedback Feedback-Feedforward

-0.2 -0.4 -0.6

0.4

Output

0.3
Input

-0.8 -1 -1.2

0.2

0.1

-1.4 -1.6

0 -1.8 -0.1 0 2 4 6 8 10 Time 12 14 16 18 20 -2 0 2 4 6 8 10 Time 12 14 16 18 20

SET POINT CHANGE

0.8 Output Setpoint 0.6


Output

0.4

0.2

0 0 2 4 6 8 10 Time 12 14 16 18 20

THANK YOU
TEJA TSSV

You might also like