Pre & Post launch drive test with TEMS 9.
Prepared by : GTL TEAM-Gurgaon
We are very thankful to Mr. Vishal Sharma for his extended support & technical guidance.
TEMS 9.1
3G DRIVE TEST TOOL
Data Collection Requirements
1 2 3 4 TEMS 9.1 SOFTWARE Dongle Mobile Phone-SONY ERICSSON Z750i GPS Garmin-72
Contents
TEAM SOFTWAR INSTALLATION KIT CONFIGRATION (Phone ,Gps) DRIVE TEST PARAMETER
BTS
STEPS FOR INSTALLING TEMS 9.1 SOFTWARE :1 -First install .Net 3 and .net 3.5 in your PC:-
2-Now install TEMS 9.1:-
3- After installing TEMS, install the driver of Dongle, Mobile phone, and GPS Beffo cable by connecting the equipment in different ports.
Dongle driver is automatically install in your PC just when you connect in your PC. But for Mobile and Beffo cable driver, you have to give the path of the driver.
4-After installing device drivers, Copy and Paste above patch files in C:\Program Files\Ericsson\TEMS Products\TEMS Investigation\Application Folder. 5-Now open the TEMS window from. My Documents\TEMS Product Files\TEMS Investigation 9.1\Workspaces. In workspaces folder you have to open Investigation WCDMA GSM.
TEMS WINDOW AFTER INSTALLATION
STEP 1 FOR Configuration :-
STEP 2 FOR AAD EQUIPMENT :-
STEP 3 FOR PORT DEFINE:3 .Step Save It 2.Step Select MS 1. Step Select it
STEP 4 FOR MAKE NEW WORKSHEET :-
STEP 5 FOR New Worksheet :-
VOICE CALL MS-SHEET
STEP 6 FOR COMMAND SEQUENCE :-
Go to command sequence
STEP 7 FOR Open the Command Sequence window
COMMAND SEQUENCE WINDOW :-
EDIT(CTRL+E)
COMMAND SEQUENCE WINDOW APPLICATION
APPLICATION TESTING FOR HSPA -MS FOR VOICE CALL
VOICE CALL TESTING
APPLICATION
VOICE CALL TESTING
4. STEP RUN(CTRL+G) 1. STEP SELECT MS
2. STEPTEST NUMBER
3. STEP CALL Duration
HSDPA TESTING APPLICATION
1. FOR HSDPA APPLICATION TESTING -----FTP DL
2. STEP SELECT DIAL-UP
DIAL-UP
3-STEP SOURCE FILE NAME :-
FILE NAME
SAVE PATH
4. STEP REMOTE ADDRESS USER ,PASSWORD
IP ADDRESS
User name
password
5 .START TO HSDPA RUN(CTRL+G)
RUN
HSDPA TESTING APPLICATION
HSUPA COMMAND SEQUENCE STEP FOR TESTING :HSUPA-MS
1. DIALUP 2.FILE NAME 3.Save path 4.IP ADDRESS 5.USER NAME
4.PASSWORD
RUN
TEAMS 9. 1 MAP WINDOW
MAP WINDOW IN TEMS PRESENTATION POSITIONING MAP :-
MAP WINDOW FUNCATION :1. .OPEN MAP 2. LAYER CONTROL
Open Map
Layer Control
Open 3G Tab File in Open Map
Open The Tab ,Vector In Layer Control :-
DRIVE TEST MAP WINDOW CELL SITE VECTOR :-
WCDMA INVESTIGATION WINDOW FOR VOICE CALL:-
PARAMETER WINDOW FOR VOICE CALL WCDMA :-
FOR VOICE CALL WCDMA RADIO PARAMETER WINDOW :-
WCDMA SERVING/ACTIVE SET + NEIGHOURS
This windows shows the Serving cell & Neighbors AS : Active Set MN: Monitered Neighbors DN: Dominant Neighbors
RADIO PARAMETERS WCDMA BAR CHARTS
FOR VOICE CALL LAYER 3 MESSAGES :THIS WINDOW OPEN GO TO PRESENTATION--- SIGNALING---LAYER 3 MESSAGES
FOR VOICE CALL EVENT COUNTER WINDOW :THIS WINDOW OPEN GO TO ANALYSIS----EVENT COUNT
AMR CODEC USAGE IN WCDMA
NOTES ON QUANTITIES DENOTING SIGNAL POWER
FOR VOICE SHORT CALL SAME WINDOW USE IN TEMS
HSDPA ANALYSIS
FOR HSDPA TESTING IN WCDMA :THIS WINDOW OPEN GO TO PRESENTATION---WCDMADATA SERVICEHSDPA ANALYSIS
It shows the Speed of HSDPA
HSDPA/HSUPA TESTING IN FTP(COMMAND PROMT) SERVER
HSDPA/HSUPA TESTING IN FTP SERVER
HSDPA/HSUPA TESTING IN FTP SERVER :-
We find out the RTT Average Value For HSDPA/HSUPA
HSUPA ANALYSIS
FOR WCDMA HSUPA TESTING :THIS WINDOW OPEN GO TO PRESENTATION-WCDMADATA SERVICE HSUPA ANALYSIS
HOW TO GENRATE MAP-INFO FILE WITH TEMS HELP :-
HOW TO GENRATE MAP-INFO FILE WITH TEMS HELP :1. STEP GO TO TOOLBAR LOGFILE ----- EXPORT LOGFILE
STEP 2 GO TO EXPORT LOGFILE ------ADD FILE:-
ADD DRIVE TEST LOGFILE
SELECT THIS FORMAT
STEP 3 GO TO SETUP WINDOW OPEN
Setup open
STEP FOR 4 AFTER SETUP WINDOW OPEN 3 Step ok
1 Select it
2 Add It
STEP FOR 5 SELECT MERGE OUTPUT AND THEN OK :-
1. SELECT IT 2 Open log file 3 Save Path 4 SELECT OK
4.STEP START TO CONVERT LOG FILE TO MAPINFO FILE:-
START IT
LOG FILE CONVET TO MAPINFO FILE SHOWS SAVE PATH FOLDER
HOW TO AUTO-GENRATE REPORT IN TEMS 9. 1
PROCESS TO REPORT GENERATOR
OPEN TEMS
LOGFILE WINDOW
REPORT GENERATOR
SELECT WCDMA OUTPUT DIRECTORY
PROPERTIES FINIES
ADD LOGFLIE
STEP 1 OPEN TEMS GO TO LOGFILE THAN REPORT GENERATOR
STEP 2 OPEN REPORT WIZARD THAN ADD LOG FILE :-
ADD LOG FILE
STEP 3 OPEN PROPERTIES AND SELECT WCDMA THEN OK :-
2.Select ok
1 .Select It
STEP 4 FOR SAVE PATH AND THAN FINISH :-
1 Save Path 2 Finish
STEP 5 FOR PROGRESS AND RESULT THEN OUT PUT REPORT:-
RETU(REMOTE ELECTRICAL TILT UNIT)
RETU(REMOTE ELECTRICAL TILT UNIT)
Two Cables are connected in RETU Dx1 Cable Tilt Monitor Cable RET Unit is monitered from RNC to maximize or minimize Electrical Tilt. Minimum tilt should be 0 & Maximum tilt should be 10 We have also update the type of antenna in RNC i.e. single band, dual band or tri band antenna.
Also one Power Switch is in RET Unit. Upper press is ON & Down Press is OFF
RETU(REMOTE ELECTRICAL TILT UNIT)
WCDMA SPECIFICATIONS
DIFFERENCES BETWEEN WCDMA & SECOND GENERATION
SUMMARY OF WCDMA PARAMETERS
SPECTRUM UMTS
Third Generation Mobile Systems
End of Section
