0% found this document useful (0 votes)
89 views9 pages

Chemical Vapor Deposition

Chemical Vapor Deposition (CVD) is a process used to deposit thin solid films on a substrate. It involves introducing vapor phase reactants into a chamber where they decompose and react at the heated substrate surface to form the thin film. CVD processes are classified by operating pressure and physical characteristics of the vapor. Plasma-enhanced CVD uses plasma to enhance chemical reaction rates, allowing deposition at lower temperatures. CVD provides conformal, uniform thin films but is limited to materials with suitable chemical reactions and cannot deposit mixtures of materials.

Uploaded by

coolrsk17
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
89 views9 pages

Chemical Vapor Deposition

Chemical Vapor Deposition (CVD) is a process used to deposit thin solid films on a substrate. It involves introducing vapor phase reactants into a chamber where they decompose and react at the heated substrate surface to form the thin film. CVD processes are classified by operating pressure and physical characteristics of the vapor. Plasma-enhanced CVD uses plasma to enhance chemical reaction rates, allowing deposition at lower temperatures. CVD provides conformal, uniform thin films but is limited to materials with suitable chemical reactions and cannot deposit mixtures of materials.

Uploaded by

coolrsk17
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 9

Chemical Vapor Deposition

Chemical Vapor Deposition


Chemical Vapor Deposition is the formation of a non-volatile solid film on a substrate by the reaction of vapor phase chemicals (reactants) that contain the required constituents. The reactant gases are introduced into a reaction chamber and are decomposed and reacted at a heated surface to form the thin film. Microfabrication processes widely use CVD to deposit materials in various forms, including:

Steps involved in a CVD process


1. Transport of reactants by forced convection to the deposition region. 2. Transport of reactants by diffusion from the main gas stream through the boundary layer to the wafer surface.
3. Adsorption of reactants on the wafer surface. 4.Surface processes, including chemical decomposition or reaction, surface migration to attachment sites (such as atomic-level ledges and kinks), site incorporation, and other surface reactions. 5. Desorption of byproducts from the surface.

6. Transport of byproducts by diffusion through the boundary layer and back to the main gas stream. 7. Transport of byproducts by forced convection away from the deposition region.

Tilted CVD susceptor

The susceptor in a horizontal epitaxial reactor is tilted so that the crosssectional area of the chamber is decreased, increasing the gas velocity along the susceptor. This compensates for both the boundary layer and depletion effects.

Classified by operating pressure: Atmospheric pressure CVD (APCVD) CVD process at atmospheric pressure. Low-pressure CVD (LPCVD) CVD process at sub-atmospheric pressures.[1] Reduced pressures tend to reduce unwanted gas-phase reactions and improve film uniformity across the wafer. Ultrahigh vacuum CVD (UHVCVD) CVD process at very low pressure, typically below 106 Pa (~108 torr). Note that in other fields, a lower division between high and ultrahigh vacuum is common, often 107 Pa. Most modern CVD processes are either LPCVD or UHVCVD. Classified by physical characteristics of vapor: Aerosol assisted CVD (AACVD) A CVD process in which the precursors are transported to the substrate by means of a liquid/gas aerosol, which can be generated ultrasonically. This technique is suitable for use with non-volatile precursors. Direct liquid injection CVD (DLICVD) A CVD process in which the precursors are in liquid form (liquid or solid dissolved in a convenient solvent). Liquid solutions are injected in a vaporization chamber towards injectors (typically car injectors). The precursor vapors are then transported to the substrate as in classical CVD process. This technique is suitable for use on liquid or solid precursors. High growth rates can be reached using this technique.

Plasma methods Microwave plasma-assisted CVD (MPCVD) Plasma-Enhanced CVD (PECVD) CVD process that utilizes plasma to enhance chemical reaction rates of the precursors.[2] PECVD processing allows deposition at lower temperatures, which is often critical in the manufacture of semiconductors. Remote plasma-enhanced CVD (RPECVD) Similar to PECVD except that the wafer substrate is not directly in the plasma discharge region. Removing the wafer from the plasma region allows processing temperatures down to room temperature. Atomic layer CVD (ALCVD) Deposits successive layers of different substances to produce layered, crystalline films. See Atomic layer epitaxy. Combustion Chemical Vapor Deposition (CCVD) Combustion Chemical Vapor Deposition or flame pyrolysis is an open-atmosphere, flame-based technique for depositing high-quality thin films and nanomaterials. Hot wire CVD (HWCVD) also known as catalytic CVD (Cat-CVD) or hot filament CVD (HFCVD), this process uses a hot filament to chemically decompose the source gases.[3] Hybrid Physical-Chemical Vapor Deposition (HPCVD) This process involves both chemical decomposition of precursor gas and vaporization of a solid source. Metalorganic chemical vapor deposition (MOCVD) This CVD process is based on metalorganic precursors. Rapid thermal CVD (RTCVD) This CVD process uses heating lamps or other methods to rapidly heat the wafer substrate. Heating only the substrate rather than the gas or chamber walls helps reduce unwanted gas-phase reactions that can lead to particle formation. Vapor phase epitaxy (VPE)

Plasma enhanced CVD system (PECVD)


As the thermal budget gets more and more constrained while more and more layers need to be added for multi-layer metallization, we want to come down with the temperature for the oxide ( or other) CVD processes. One way for doing this is to supply the necessary energy for the chemical reaction by ionizing the gas, thus forming a plasma.

Advantages of CVD processes


CVD processes are ideally suited for depositing thin layers of materials on some substrate. In contrast to some other deposition processes which we will encounter later, CVD layers always follow the contours of the substrate: They are conformal to the substrate as shown below.

Disadvantages of CVD processes


The two most important ones (and the only ones we will address here) are: 1. 2. They are not possible for some materials; there simply is no suitable chemical reaction. They are generally not suitable for mixtures of materials.

You might also like