Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

2005 Pearson Education South Asia Pte Ltd
Applied Fluid Mechanics

1. The Nature of Fluid and the
Study of Fluid Mechanics
2. Viscosity of Fluid
3. Pressure Measurement
4. Forces Due to Static Fluid
5. Buoyancy and Stability
6. Flow of Fluid and Bernoullis Equation
7. General Energy Equation
8. Reynolds Number, Laminar Flow, Turbulent
Flow and Energy Losses Due to Friction
9. Velocity Profiles for Circular
Sections and Flow in
Noncircular Sections
10.Minor Losses
11.Series Pipeline Systems
12.Parallel Pipeline Systems
13.Pump Selection and Application
14.Open-Channel Flow
15.Flow Measurement
16.Forces Due to Fluids in Motion
17.Drag and Lift
18.Fans, Blowers, Compressors
and the Flow of Gases
19.Flow of Air in Ducts
4. Forces due to Static Fluid
Chapter Objectives
1. Compute the force exerted on a plane area by a
pressurized gas.
2. Compute the force exerted by any static fluid acting
on a horizontal plane area.
3. Compute the resultant force exerted on a
rectangular wall by a static liquid.
4. Define the term center of pressure.
5. Compute the resultant force exerted on any
submerged plane area by a static liquid.
6. Show the vector representing the resultant force on
any submerged plane area in its proper location and
direction.
Chapter Objectives
7. Visualize the distribution of force on a submerged
curved surface.
8. Compute the total resultant force on the curved
surface.
9. Compute the direction in which the resultant force
acts and show its line of action on a sketch of the
surface.
10. Include the effect of a pressure head over the liquid
on the force on a plane or curved surface.
Chapter Outline
1. Introductory Concepts
2. Gases Under Pressure
3. Horizontal Flat Surfaces Under Liquids
4. Rectangular Walls
5. Submerged Plane Areas-General
6. Development of the General Procedure for
Forces on Submerged Plane Areas
7. Piezometric Head
8. Distribution of Force on a Submerged Curved
Surface
9. Effect of a Pressure Above the Fluid Surface

Chapter Outline
10. Forces on a Curved Surface with Fluid Below It
11. Forces on Curved Surfaces with Fluid Above and
Below
4.1 Introductory Concepts
Fig 4.1 shows the examples of cases where forces on
submerged areas must be computed.

4.1 Introductory Concepts
In each case, the fluid exerts a force on the surface of
interest that acts perpendicular to the surface,
considering the basic definition of pressure, p = F/A
and the corresponding form, F = pA.
We apply these equations directly only when the
pressure is uniform over the entire area of interest.
An example is when the fluid is a gas for which we
consider the pressure to be equal throughout the gas
because of its low specific weight.

4.2 Gases Under Pressure
Fig 4.2 shows the fluid power cylinder.
The air pressure acts on the piston face, producing a
force that causes the linear movement of the rod.
The pressure also acts on the end of the cylinder,
tending to pull it apart.
Therefore, we can calculate the force on the piston
and the cylinder ends directly from F = pA.

4.2 Gases Under Pressure
Example 4.1
If the cylinder in Fig. 4.2 has an internal diameter of 51
mm and operates at a pressure of 2070 kPa (gage),
calculate the force on the ends of the cylinder.
( )
kN m
m
m N
F
m
m D
A
pA F
41 . 4 002 . 0
/ 10 2070
002 . 0
4
051 . 0
4
2
2
2 3
2
2
2
=
=
= = =
=
t t
Example 4.1
Notice that gage pressure was used in the calculation of
force instead of absolute pressure. The additional force
due to atmospheric pressure acts on both sides of the
area and is thus balanced. If the pressure on the outside
surface is not atmospheric, then all external forces
must be considered to determine a net force on the
area.
4.3 Horizontal Flat Surfaces Under Liquids
Fig 4.3 shows the cylindrical drum.
The pressure in the water at the bottom of the drum is
uniform across the entire area because it is a
horizontal plane in a fluid at rest.
We can simply use F = pA to calculate the force on
the bottom

Example 4.2
If the drum in Fig. 4.3 is open to the atmosphere at the
top, calculate the force on the bottom.

To use we must first calculate the pressure at the bottom
of the drum and the area of the bottom:
Example 4.2
Would there be any difference between the force on the
bottom of the drum in Fig. 4.3 and that on the bottom of
the cone-shaped container in Fig. 4.4?
Example 4.2
The force would be the same because the pressure at
the bottom is dependent only on the depth and specific
weight of the fluid in the container. The total weight of
fluid is not the controlling factor.

Comment: The force computed in these two example
problems is the force exerted by the fluid on the inside
bottom of the container. Of course, when designing the
support structure for the container, the total weight of the
container and the fluids must be considered. For the
structural design, the cone-shaped container will be
lighter than the cylindrical drum.
4.4 Rectangular Walls
Fig 4.5 shows the rectangular walls.
They are walls which exposed to a pressure varying
from zero on the surface of the fluid to a maximum at
the bottom of the wall.
The force due to the fluid pressure tends to overturn
the wall or break it at the place where it is fixed to the
bottom.
The actual force is distributed over the entire wall, but
for the purpose of analysis it is desirable to determine
the resultant force and the place where it acts, called
the center of pressure.

Fig 4.6 shows the vertical rectangular wall.

The total resultant force can be calculated from the
equation

where p
avg
is the average pressure and A is the total
area of the wall.
But the average pressure is that at the middle of the
wall and can be calculated from the equation

where h is the total depth of the fluid.
Therefore, we have

The center of pressure is at the centroid of the
pressure distribution triangle, one third of the distance
from the bottom of the wall.
The resultant force acts perpendicular to the wall at
this point.
Below are the procedures for computing the force on
a rectangular wall:
1. Calculate the magnitude of the resultant force from

2. Locate the center of pressure at a vertical distance
of from the bottom of the wall.
3. Show the resultant force acting at the center of
pressure perpendicular to the wall.
Example 4.4
In Fig. 4.6, the fluid is gasoline and the total depth is 3.7
m. The wall is 12.2 m long. Calculate the magnitude of
the resultant force on the wall and the location of the
center of pressure.
Example 4.4
Step 1
( )
( )( )
( )( )
kN m
m
m
m kN
F
m m m A
m kN m kN
A h F
R
R
0 . 557 14 . 45
2
7 . 3 / 67 . 6
14 . 45 2 . 12 7 . 3
/ 67 . 6 / 81 . 9 68 . 0
2 /
2
3
2
2
3 3
= =
= =
= =
=

Example 4.4
Step 2

Step 3
The force acts perpendicular to the wall at the center of
pressure as shown in Fig. 4.6.

Example 4.5
Figure 4.7 shows a dam 30.5 m long that retains 8 m of
fresh water and is inclined at an angle of 60. Calculate
the magnitude of the resultant force on the dam and the
location of the center of pressure.
Example 4.5
Step 1

To calculate the area of the dam we need the length of
its face, called L in Fig. 4.7:

Then, the area of the dam is

Example 4.5
Step 1

Now we can calculate the resultant force:
Example 4.5
Step 2

The center of pressure is at a vertical distance of

from the bottom of the dam, or, measured from the
bottom of the dam along the face of the dam, the center
of pressure is at

Example 4.5
Step 2

Measured along the face of the dam we define

We show F
R
acting at the center of pressure
perpendicular to the wall.

4.5 Submerged Plane Areas - General
Fig 4.85 shows the force on a submerged plane
area.

The standard dimensions and symbols used in the
procedure described later are shown in the figure
and defined as follows:
Fig 4.9 shows the properties of a rectangle.

Below are the procedure for computing the force on
a submerged plane area:
1. Identify the point where the angle of inclination of the
area of interest intersects the level of the free
surface of the fluid. This may require the extension
of the angled surface or the fluid surface line. Call
this point S.
2. Locate the centroid of the area from its geometry.
3. Determine h
c
as the vertical distance from the level
of the free surface down to the centroid of the area.
4. Determine L
c
as the inclined distance from the level
of the free surface down to the centroid of the area.
This is the distance from S to the centroid. Note that
h
c
and L
c
are related by

5. Calculate the total area A on which the force is to be
determined.
6. Calculate the resultant force from

where is the specific weight of the fluid. This
equation states that the resultant force is the product
of the pressure at the centroid of the area and the
total area.
7. Calculate I
c
the moment of inertia of the area about
its centroidal axis.
8. Calculate the location of the center of pressure from

Notice that the center of pressure is always below the
centroid of an area that is inclined with the horizontal. In
some cases it may be of interest to calculate only the
difference between L
p
and L
c
from

9. Sketch the resultant force F
R
acting at the center of
pressure, perpendicular to the area.
10. Show the dimension L
p
on the sketch in a manner similar
to that used in Fig. 4.8.
11. Draw the dimension lines for L
p
and L
c
from a reference
line drawn through point S and perpendicular to the
angle of inclination of the area.
12. If it is desired to compute the vertical depth to the center
of pressure, h
p
either of two methods can be used. If the
distance L
p
has already been computed, use

Alternatively, Step 8 could be avoided and h
p
can be
computed directly from

We will now use the programmed instruction approach to
illustrate the application of this procedure.

Example 4.6
The tank shown in Fig. 4.8 contains a lubricating oil with
a specific gravity of 0.91. A rectangular gate with the
dimensions B=1.2 m and H=0.6 m is placed in the
inclined wall of the tank (=60).The centroid of the gate
is at a depth of 1.5 m from the surface of the oil.
Calculate (a) the magnitude of the resultant force F
R
on
the gate and (b) the location of the center of pressure.
Example 4.6
The terms L
c
and h
c
are related in this case by

Therefore, we have

Because the area of the rectangle is BH,

We need the specific weight of the oil:

Then we have

We find that for a rectangle,

Because I
c
=0.02 m
4
, L
c
=1.73 m, and A=0.72 m
2
,

Example 4.6
kN m m
m
kN
A h F
c R
63 . 9 72 . 0 5 . 1
92 . 8
2
3
0
= = =
( )( )
m m m L
m m
m
m
A L
I
L L
p
c
c
c p
75 . 1 016 . 0 73 . 1
72 . 0 73 . 1
02 . 0
73 . 1
2
4
= + =
+ = + =
This means that the center of pressure is 0.016 m (or 16
mm) below the centroid of the gate.

Be sure you understand how the dimension L
p
is drawn
from the reference line.

Example 4.6
4.6 Development of the General Procedure for Forces on Submerged Plane Areas
The resultant force is defined as the summation of
the forces on small elements of interest.
Fig 4.11 shows the development of the general
procedure for forces on submerged plane areas.

The resultant force is defined as the summation of
the forces on small elements of interest.
Fig 4.11 shows the development of the general
procedure for forces on submerged plane areas.
On any small area dA, there exists a force dF acting
perpendicular to the area owing to the fluid pressure
p. But the magnitude of the pressure at any depth h
in a static liquid of specific weight is p = h.
Then, the force is

Because the area is inclined at an angle it is
convenient to work in the plane of the area, using y
to denote the position on the area at any depth h.
Note that

where y is measured from the level of the free
surface of the fluid along the angle of inclination of
the area. Then,

The summation of forces over the entire area is
accomplished by the mathematical process of
integration,

From mechanics we learn that is equal to the
product of the total area times the distance to the
centroid of the area from the reference axis. That is,

Then, the resultant force is

This is the same form as Eq. (44). Because each of
the small forces dF acted perpendicular to the area,
the resultant force also acts perpendicular to the
area.

4.6.1 Center of Pressure
The center of pressure is that point on an area
where the resultant force can be assumed to act so
as to have the same effect as the distributed force
over the entire area due to fluid pressure.
The moment of each small force dF is

But

Now, if we assume that the resultant force acts at
the center of pressure, its moment with respect to
the axis through S is F
R
L
p
. Then

Substituting F
R
for from Eq. (410) gives

A more convenient expression can be developed by
using the transfer theorem for moment of inertia from
mechanics.

Equation (412) then becomes

Rearranging gives the same form as Eq. (46):

We now continue the development by creating an
expression for the vertical depth to the center of
pressure h
p
. Starting from Eq. (413), note the
following relationships:

Then
4.7 Piezometric Head
In all the problems demonstrated so far, the free
surface of the fluid was exposed to the ambient
pressure where p = 0 (gage).
Fig 4.12 shows the illustration of piezometric head.

4.7 Piezometric Head
A convenient method uses the concept of
piezometric head, in which the actual pressure
above the fluid, is converted into an equivalent depth
of the fluid, that would create the same pressure
(Fig. 4.12):

This depth is added to any depth h below the free
surface to obtain an equivalent depth, That is,

The equivalent depth to the centroid is
Example 4.7
Repeat Example Problem 4.6, except consider that the
tank shown in Fig. 4.8 is sealed at its top and that there
is a pressure of 10.3 kPa(gage) above the oil.

Several calculations in the solution to Example Problem
4.6 used the depth to the centroid, given to be 1.5 m
below the surface of the oil. With the pressure above the
oil, we must add the piezometric head from Eq. (414).
Using =8.92 kN/m3, we get

m
m kN
m kN p
h
a
a
15 . 1
/ 92 . 8
/ 3 . 10
3
2
= = =

Example 4.7
Then, the equivalent depth to the centroid is

The resultant force is then

Compare this with the value of 9.63 kN found before for
the open tank. The center of pressure also changes
because the distance L
c
changes L
ce
to as follows:

( )( )
mm m
m m
m
A L
I
L L
m m h L
ce
c
ce pe
ce cce
9 009 . 0
72 . 0 0 . 3
02 . 0
0 . 3 60 sin / 65 . 2 sin /
2
4
= = = =
= = = u
Example 4.7
Then, the equivalent depth to the centroid is

The resultant force is then

Compare this with the value of 9.63 kN found before for
the open tank. The center of pressure also changes
because the distance L
c
changes L
ce
to as follows:

4.8 Distribution of Force on a Submerged Curved Surface
Fig 4.13 shows the tank with a curved surface
containing a static fluid.

One way to visualize the total force system involved
is to isolate the volume of fluid directly above the
surface of interest as a free body and show all the
forces acting on it, as shown in Fig. 4.14.
Fig 4.14 shows the free-body diagram of a volume of
fluid above the curved surface.

4.8.1 Horizontal Force
The vertical solid wall at the left exerts horizontal
forces on the fluid in contact with it in reaction to the
forces due to the fluid pressure.
The magnitude of F
2b
and its location can be found
using the procedures developed for plane surfaces.
That is,

where h
c
is the depth to the centroid of the projected
area.

Calling the height of the rectangle s, you can see
that h
c
= h + s/2. Also, the area is sw, where w is the
width of the curved surface. Then,

Again using the principles developed earlier, we get

For the rectangular projected area, however,

Then,
4.8.2 Vertical Force
The vertical component of the force exerted by the
curved surface on the fluid can be found by
summing forces in the vertical direction.
Only the weight of the fluid acts downward, and only
the vertical component acts upward.
4.8.3 Resultant Force
The total resultant force is

The resultant force acts at an angle relative to the
horizontal found from

4.8.4 summary of the Procedure for Computing the Force on a Submerged Curved Surface
1. Isolate the volume of fluid above the surface.
2. Compute the weight of the isolated volume.
3. The magnitude of the vertical component of the
resultant force is equal to the weight of the isolated
volume. It acts in line with the centroid of the isolated
volume.
4. Draw a projection of the curved surface onto a
vertical plane and determine its height, called s.
5. Compute the depth to the centroid of the projected
area from the below, where h is the depth to the top
of the projected area.

6. Compute the magnitude of the horizontal component
of the resultant force from

7. Compute the depth to the line of action of the
horizontal component from

8. Compute the resultant force from

9. Compute the angle of inclination of the resultant
force relative to the horizontal from

10. Show the resultant force acting on the curved
surface in such a direction that its line of action
passes through the center of curvature of the
surface.

Example 4.8
For the tank shown in Fig. 4.13, the following
dimensions apply:

Compute the horizontal and vertical components of the
resultant force on the curved surface and the resultant
force itself. Show these force vectors on a sketch.

Example 4.8
Using the steps outlined above:
1. The volume above the curved surface is shown in Fig.
4.15.
2. The weight of the isolated volume is the product of the
specific weight of the water times the volume. The
volume is the product of the area times the length w.
Example 4.8
Example 4.8
3. Then Fv = 153.7N, acting upward through the centroid
of the volume. The location of the centroid is found
using the composite-area technique. Refer to Fig.
4.15 for the data. Each value should be obvious
except the location of the centroid of the quadrant.
From Appendix L,

Then, the location of the centroid for the composite
area is

Example 4.8
4. The vertical projection of the curved surface is shown
in Fig. 4.15. The height s equals 1.50 m.
5. The depth to the centroid of the projected area is

6. The magnitude of the horizontal force is

7. The depth to the line of action of the horizontal
component is found from

Example 4.8
8. The resultant force is computed from

9. The angle of inclination of the resultant force relative
to the horizontal is computed from

Example 4.8
10. The horizontal component, the vertical component,
and the resultant force are shown in Fig. 4.16. Note
that the line of action F
R
of is through the center of
curvature of the surface. Also note that the vertical
component is acting through the centroid of the
volume of liquid above the surface. The horizontal
component is acting through the center of pressure
of the projected area at a depth h
p
from the level of
the free surface of the fluid.
Example 4.8
Example 4.8
10. The horizontal component, the vertical component,
and the resultant force are shown in Fig. 4.16. Note
that the line of action F
R
of is through the center of
curvature of the surface. Also note that the vertical
component is acting through the centroid of the
volume of liquid above the surface. The horizontal
component is acting through the center of pressure
of the projected area at a depth h
p
from the level of
the free surface of the fluid.
4.9 Effect of Pressure above the Fluid Surface
If an additional pressure exists above the fluid or if
the fluid itself is pressurized, the effect is to add to
the actual depth a depth of fluid equivalent to p/.
This is the same procedure, called piezometric head.
4.10 Forces on a Curved Surface with Fluid Below It
Fig 4.17 shows the curved surface restraining a
liquid below it.

The pressure in the fluid at any point is dependent
on the depth of fluid to that point from the level of the
free surface.
This situation is equivalent to having the curved
surface supporting a volume of liquid above it,
except for the direction of the force vectors.
Fig 4.18 shows the forces exerted by a curved
surface on the fluid.
As before, the horizontal component of the force
exerted by the curved surface on the fluid is the
force on the projection of the curved surface on a
vertical plane.
The vertical component is equal to the weight of the
imaginary volume of fluid above the surface.
4.11 Forces on Curved Surfaces with Fluid above and below
Fig 4.19 shows the semicylindrical gate.

The force due to fluid pressure would have a
horizontal component acting to the right on the gate.
This force acts on the projection of the surface on a
vertical plane and is computed in the same manner
as used in Section 4.8.
However, there is also a force acting upward on the
bottom surface of the gate equal to the total weight
of the fluid, both real and imaginary, above that
surface.
The net vertical force is the difference between the
two forces, equal to the weight of the semicylindrical
volume of fluid displaced by the gate itself.
Fig 4.19 shows the volumes used to compute the net
vertical force on the gate.

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Copyright:

Available Formats

2005 Pearson Education South Asia Pte Ltd

Applied Fluid Mechanics

4. Forces due to Static Fluid

You might also like

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Document Informationclick to expand document informationRobert L.Mott applied fluid mechanics chapter 4

Document Informationclick to expand document information

Copyright:

Available Formats

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Forces Due To Static Fluid: 2005 Pearson Education South Asia Pte LTD

Uploaded by

Copyright:

Available Formats

2005 Pearson Education South Asia Pte Ltd

Applied Fluid Mechanics

4. Forces due to Static Fluid

You might also like