Cam

Cam design
A cam is a rotating machine element which gives reciprocating or oscillating motion to another element known as follower. The cam and the follower have a line contact and constitute a higher pair. The cams are usually rotated at uniform speed by a shaft, but the follower motion is predetermined and will be according to the shape of the cam.
Classification of Followers
1. According to the surface in contact (a) Knife edge follower: When the contacting end of the follower has a sharp knife edge, it is called a knife edge follower, as shown in Fig. 20.1 (a) Disadvantage: excessive wear (b) Roller follower: When the contacting end of the follower is a roller, it is called a roller follower, as shown in Fig. 20.1 (b). Advantage: Since the rolling motion takes place between the contacting surfaces (i.e. the roller and the cam), therefore the rate of wear is greatly reduced. (c) Flat faced or mushroom follower: When the contacting end of the follower is a perfectly flat face, it is called a flatfaced follower, as shown in Fig. 20.1 (c). Advantage: It may be noted that the side thrust between the follower and the guide is much reduced in case of flat faced followers. The only side thrust is due to friction between the contact surfaces of the follower
(d) Spherical faced follower: When the contacting end of the follower is of spherical shape, it is called a spherical faced follower, as shown in Fig. 20.1 (d). It may be noted that when a flat-faced follower is used in automobile engines, high surface stresses are produced. Advantage: In order to minimize these stresses, the flat end of the follower is machined to a spherical shape.
2. According to the motion of the follower. two types: (a) Reciprocating or translating follower. as shown in Fig. 20.1 (a) to (d) are all reciprocating or translating followers. (b) Oscillating or rotating follower. as shown in Fig 20.1 (e), is an oscillating or rotating follower.
3. According to the path of motion of the follower. two types: (a) Radial follower. as shown in Fig. 20.1 (a) to (e), are all radial followers. (b) Off-set follower as shown in Fig. 20.1 ( f ), is an off-set follower.
Terms used in CAM
Fig. 20.3 shows a radial cam with reciprocating roller follower. The following terms are important in order to draw the cam profile. 1. Base circle. It is the smallest circle that can be drawn to the cam profile.
2. Trace point. It is a reference point on the follower and is used to generate the pitch curve. In case of knife edge follower, the knife edge represents the trace point and the pitch curve corresponds to the cam profile. In a roller follower, the center of the roller represents the trace point. 3. Pressure angle. It is the angle between the direction of the follower motion and a normal to the pitch curve. This angle is very important in designing a cam profile. If the pressure angle is too large, a reciprocating follower will jam in its bearings. 4. Pitch point. It is a point on the pitch curve having the maximum pressure angle. 5. Pitch circle. It is a circle drawn from the center of the cam through the pitch points. 6. Pitch curve. It is the curve generated by the trace point as the follower moves relative to the cam. For a knife edge follower, the pitch curve and the cam profile are same whereas for a roller follower, they are separated by the radius of the roller. 7. Prime circle. It is the smallest circle that can be drawn from the center of the cam and tangent to the pitch curve. For a knife edge and a flat face follower, the prime circle and the base circle are identical. For a roller follower, the prime circle is larger than the base circle by the radius of the roller. 8. Lift or stroke. It is the maximum travel of the follower from its lowest position to the top-most position.
Motion of the Follower

The follower, during its travel, may have one of the following motions. 1. Uniform velocity, 2. Simple harmonic motion, 3. Uniform acceleration and retardation, and 4. Cycloidal motion.
1. Displacement, Velocity and Acceleration Diagrams Follower Moves
with Uniform Velocity

The abscissa (base) represents the time or it may represent the angular displacement of the cam in degrees. The ordinate represents the displacement, or velocity or acceleration of the follower. Since the follower moves with uniform velocity during its rise and return stroke, therefore the slope of the displacement curves must be constant. In other words, AB1 and C1D must be straight lines.
Acceleration is infinity due to the fact that the follower is required to start from rest and has to gain a velocity within no time. This is only possible if the acceleration or retardation at the beginning and at the end of each stroke is infinite. In order to have the acceleration and retardation within the finite limits, it is necessary to modify the conditions which govern the motion of the follower. This may be done by rounding off the sharp corners of the displacement diagram at the beginning and at the end of each stroke, as shown in Fig. 20.5 (a). By doing so, the velocity of the follower increases gradually to its maximum value at the beginning of each stroke and decreases gradually to zero at the end of each stroke as shown in Fig. 20.5 (b).
Figure: Camshaft of an IC engine
Displacement, Velocity and Acceleration diagram (Follower in SHM)

The displacement, velocity and acceleration diagrams when the follower moves with simple harmonic motion are shown in Fig. 20.6 (a), (b) and (c) respectively. The displacement diagram is drawn as follows : 1. Draw a semi-circle on the follower stroke as diameter. 2. Divide the semi-circle into any number of even equal parts (say eight). 3. Divide the angular displacements of the cam during out stroke and return stroke into the same number of equal parts. 4. The displacement diagram is obtained by projecting the points as shown in Fig. 20.6 (a).
The velocity and acceleration diagrams are shown in Fig. 20.6 (b) and (c) respectively. Since the follower moves with a simple harmonic motion, therefore velocity diagram consists of a sine curve and the acceleration diagram is a cosine curve. We see from Fig. 20.6 (b) that the velocity of the follower is zero at the beginning and at the end of its stroke and increases gradually to a maximum at mid-stroke. On the other hand, the acceleration of the follower is maximum at the beginning and at the ends of the stroke and diminishes to zero at mid-stroke.
= angular velocity
t = S/V
Displacement, Velocity and Acceleration diagram (Follower in uniform acceleration)

The displacement, velocity and acceleration diagrams when the follower moves with uniform acceleration and retardation are shown in Fig. 20.8 (a), (b) and (c) respectively. We see that the displacement diagram consists of a parabolic curve and may be drawn as discussed below :
V0 = max velocity
Construction of Cam profile for a radial cam

In constructing the cam profile, the principle of kinematic inversion is used, i.e. the cam is imagined to be stationary and the follower is allowed to rotate in the opposite direction to the cam rotation.
Circular Arc Cam with Flat-faced Follower

When the flanks of the cam connecting the base circle and nose are of convex circular arcs, then the cam is known as circular arc cam.
A symmetrical circular arc cam operating a flat-faced follower is shown in Fig. 20.44, in which O and Q are the centres of cam and nose respectively. EF and GH are two circular flanks whose centres lie at P and P respectively
We shall consider the following two cases : 1. When the flat face of the follower has contact on the circular flank, and 2. When the flat face of the follower has contact on the nose. In deriving the expressions for displacement, velocity and acceleration of the follower for the above two cases, it is assumed that the cam is fixed and the follower rotates in the opposite sense to that of the cam.
When the flat face of the follower has contact on the circular flank
the flat face of the follower has contact at E (i.e. at the junction of the circular flank and base circle). When the cam turns through an angle (less than ) relative to the follower, the contact of the flat face of the follower will shift from E to C on the circular flank, such that flat face of the follower is perpendicular to PC. Since OB is perpendicular to BC, therefore OB is parallel to PC. From O, draw OD perpendicular to PC.
From the geometry of the figure, the displacement or lift of the follower (x) at any instant for contact on the circular flank, is given by X = CDEO . . . (i) We know that CD=PCPD=PEOP cos =OP+OEOPcos =OE+OP (1cos)
From the above expression, we see that at the beginning of the ascent (i.e. when = 0 ), the velocity is zero (because sin 0 = 0 ) and it increases as increases. The velocity will be maximum when = , i.e. when the contact of the follower just shifts from circular flank to circular nose. Therefore maximum velocity of the follower,
From the above expression, we see that at the beginning of the ascent (i.e. when = 0 ), the acceleration is maximum (because cos 0 = 1 ) and it decreases as increases. The acceleration will be minimum when = .
When the flat face of the follower has contact on the nose
The flat face of the follower having contact on the nose at C is shown in Fig. 20.45. The centre of curvature of the nose lies at Q. In this case, the displacement or lift of the follower at any instant when the cam has turned through an angle (greater than ) is given by
Quiz # 1 Monday (30/09/2013) Point: 10 Time: 15 min Syllabus: 1. Basic concepts 2. Structure of mechanics 3. Kinematic pairs 4. Degree of freedom 5. Cams

Cam

Uploaded by

Copyright:

Available Formats

Cam

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cam

Uploaded by

Copyright:

Available Formats

Cam design

Terms used in CAM

Motion of the Follower

1. Displacement, Velocity and Acceleration Diagrams Follower Moves

with Uniform Velocity

Figure: Camshaft of an IC engine

Displacement, Velocity and Acceleration diagram (Follower in SHM)

Displacement, Velocity and Acceleration diagram (Follower in uniform acceleration)

Construction of Cam profile for a radial cam

Circular Arc Cam with Flat-faced Follower

You might also like