Finalised GSM Overview
Finalised GSM Overview
GSM
By: Rahul Mishra 08720902809
What is GSM?
is a digital cellular communications system. It was developed in order to create a common European mobile telephone standard but it has been rapidly accepted worldwide.
Formerly it was Groupe Spciale Mobile (founded
Evolution of GSM.
The idea of cell-based mobile radio systems appeared at Bell Laboratories (in USA) in the early 1970s. However, mobile cellular systems were not introduced for commercial use until the 1980s. But in the beginnings of cellular systems, each country developed its own system, which was an undesirable situation for the following reasons: The equipment was limited to operate only within the boundaries of each country. The market for each mobile equipment was limited.
European Posts and telecommunications (CEPT) formed, in 1982 ,the Group Special Mobile (GSM) in order to develop a pan-European mobile cellular radio system . The standardized system had to meet certain criteria: Spectrum efficiency International roaming Low mobile and base stations costs Good voice quality Compatibility with other systems such as ISDN (Integrated Services Digital Network) Ability to support new services
GENERATION OF GSM
1st generation:- Analog mobile technologies :- AMPS , TACS & NMT. 2nd generation:- digital mobile technologies :- GSM , CDMA 2.5generation:- Enhancement of GSM:- GPRS 3rd generation:- Technologies coursed by ITU-IMT
The following table lists the key events in the GSM evolution
AMPSAdvanced Mobile Phone System TACS----Total Access Communication System. NMT----Nordic Mobile Telephones
GPRS
GSM
GPRS. 3G---Uses WCDMA technologies Over Air interface (5MHz),provides faster communication like voice, fax and internet. video calling, live streaming
GSM STANDARDS
GSM-900 Standard
The GSM-900 standard is a standard for digital voice transmission in the 900 MHz band. This so called primary band" includes two sub bands of 25 MHz
GSM-1800 Standard In GSM-1800, 1800 MHz band was allocated for digital mobile telephone services which has frequency of 75 MHz. This was three times the bandwidth allocated for GSM-900. GSM-1900 Standard GSM-1900 is the standard for the 1900MHz band. It includes the same network component as the GSM-900 or GSM-1800. The band width of this standard is 60 MHz. GSM Channels/Carriers The following table will show the channels and carriers of different GSM models
PGSM(Pri maryGSM) 900 Uplink frequency 890-915 MHz Down link frequency 935-960 MHz
GSM 1800
GSM 1900
124
174
144
374
299
45 MHZ
45 MHZ
45 MHZ
95 MHZ
80 MHZ
between adjacent signal spectra to minimize crosstalk between channels. TDMA (TIME DIVISION MULTIPLE ACCESS):- In a TDMA system, data from each user is conveyed in time intervals called Time slots. Several slots make up a frame . Each slot is made up of a preamble plus information bits addressed to various stations .the functions of the preamble are to provide identification and incidental information and to allow synchronization of the slot at the intended receiver .Intersymbol interference is the main problem in the TDMA.
station is the mobile subscriber ISDN number (MSISDN). It is assigned to the subscriber (his or her SIM, respectively), such that a mobile station set can have several MSISDNs depending on the SIM. CC+NDC+SN - 12digits IMSI - Each registered user is uniquely identified by its international mobile subscriber identity (IMSI). It is stored in the subscriber identity module (SIM) A mobile station can only be operated if a SIM with a valid IMSI is inserted into equipment with a valid IMEI. MCC (3)+MNC (2)+MSIN (10) - 15 digits
subscriber, can assign a temporary mobile subscriber identity (TMSI) which has only local significance in the area handled by the VLR. It is stored on the network side only in the VLR and is not passed to the HLR. 4 octets IMEI - The international mobile station equipment identity (IMEI) uniquely identifies a mobile station internationally. It is a kind of serial number. The IMEI is allocated by the equipment manufacturer and registered by the network operator and registered by the network operator who stores it in the EIR. By means of IMEI one recognizes obsolete, stolen or non-functional equipment. TAC+FAC+SNR+Spare - 15 digits LAI - The Location Area Identifier (LAI) is also structured hierarchically and internationally unique as follows: MCC+MNC+LAC
multiplexing and time-division multiplexing for providing multiple access by mobile stations.
GSM utilizes a cellular concept, in which a geographical area is divided into planned radio cells , with one BTS per cell with which a mobile can make contact. The radio cells, each having the exclusive use of specific FDM channels. The same frequencies are only used after sufficiently long distances in neighboring cell clusters. The cell radius can vary according to user density from 300 mtrs to 35 Kms.
Cells
GSM ARCHITECTURE
Um interface
The "air" or radio interface standard that is used for exchanges between a mobile (ME) and a base station (BTS / BSC). and a BTS This is a BSS internal interface linking the BSC
The A interface is used to provide communication between the BSS and the MSC. The B interface exists between the MSC and the VLR
VLR and HLR. E interface The E interface provides communication between two MSCs. F interface The F interface is used between an MSC and EIR. G interface The G interface interconnects two VLRs of different MSCs. H interface The H interface exists between the MSC the SMS-G. It transfers short messages I interface The I interface can be found between the MSC and the ME.
Mobile station(MS)
The mobile station (MS) represents the terminal equipment used by the wireless subscriber supported by the GSM Wireless system. Man machine interface. The SIM may be a removable module, while the equipment identity is not linked to a particular subscriber.
Functions of a Mobile Station : Radio transmission termination. Radio Channel Management. Speech Encoding/Decoding .Radio Link error Protection. Flow control of data. Mobility Management.
SIM (Subscriber identity Module) - It is basically a removable smart card in compliance
with the ISO 7816 standard and a plug-in module (25 x 15 mm) .It includes a microprocessor with all the subscriber-related information . SIM (and consequently MS) is protected by a Personal Identification Number (PIN). It has a PIN Unblocking Key (PUK) used to unblock it. Information stored in a SIM card- Serial number International Mobile Subscriber Identity (IMSI) Security authentication and cyphering information Temporary Network information (LAI, TMSI)
BSS
The BSS is responsible for communicating with mobile stations in cell areas. BTS is a network element with transmission and reception devices (transceivers) to and from the MS, including antennas signal processing specific devices for the Air interface management It can be considered as a complex radio modem controlled by the BSC It is involved also in the transmission and reception with the BSC through the A-bis interface It has just executive functions (no management Function Broadcast/receive to/from the MS either signalling and traffic signals Perform source and channel coding Modulate/Demodulate signals to be broadcasted/received through the Air interface radio channel Multiplex the information to be transmitted over each carrier.
BSC One BSC controls one or more BTSs and can perform
BSC Function Control and supervise the BTSs Configure each cell with the allocation and the release of traffic
and signalling channels Manage the paging operation Collect the signals quality measures acquired by the BTSs over the downlink and uplink channels Manage all the radio interfaces Manage the handover procedures Transcode and Sub-multiplex the bit stream
Function of NSS
Call control identification of the subscriber establishing a call and release of the connection after the call is over Mobility management taking care of the location of the subscribers before, during and after a call Collecting the charging information about a call number of the caller and of the called subscriber length and type of the provided services Transfer the acquired charging information to the Billing centre Signalling with other networks and BSS through the different interfaces Subscriber data handling Data storage permanently or temporarily in some databases OMCR:- It is used to monitor and maintain the alarms of the system.
Comprises of the Base Transceiver Station (BTS) Base Station Controller (BSC)
Input alarms include : Power supply unit- input failure It is due to loss of AC power Power supply unit- output failure Due to loss of output power because of failure of PSU
Smoke alarm BTS cabinet over temperature (max. 70C )
for GSM only systems: Intra-BTS handover: This form of GSM handover occurs if it is required to change the frequency or slot being used by a mobile because of interference, or other reasons. In this form of GSM handover, the mobile remains attached to the same base station transceiver, but changes the channel or slot. Inter-BTS Intra BSC handover: This for of GSM handover or GSM handoff occurs when the mobile moves out of the coverage area of one BTS but into another controlled by the same BSC. In this instance the BSC is able to perform the handover and it assigns a new channel and slot to the mobile, before releasing the old BTS from communicating with the mobile. Inter-BSC handover: When the mobile moves out of the range of cells controlled by one BSC, a more involved form of handover has to be performed, handing over not only from one BTS to another but one BSC to another. For this the handover is controlled by the MSC. Inter-MSC handover: This form of handover occurs when changing between networks. The two MSCs involved negotiate to control the handover