Scribd
Upload
279 views

Chapter 3 - Methods of Analysis

The document discusses different methods for analyzing electrical circuits including nodal analysis and mesh analysis. It covers analyzing circuits both with and without voltage and current sources. Key steps and concepts are presented for applying nodal and mesh analysis including dealing with supernodes and supermeshes formed by sources between nodes or meshes.

Uploaded by

Sarah Azlina
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
279 views

Chapter 3 - Methods of Analysis

The document discusses different methods for analyzing electrical circuits including nodal analysis and mesh analysis. It covers analyzing circuits both with and without voltage and current sources. Key steps and concepts are presented for applying nodal and mesh analysis including dealing with supernodes and supermeshes formed by sources between nodes or meshes.

Uploaded by

Sarah Azlina
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 18

EEE3103 Circuits and Signals

Chapter 3
Methods of Analysis

PowerPoint Slides by Alex Chan

Chapter Outline
3.1 3.2 3.3 3.4 3.5 Introduction Nodal analysis (without voltage sources) Nodal analysis with voltage sources Mesh analysis (without current sources) Mesh analysis with current sources.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.1

Introduction

There are two ways to write the minimum number of simultaneous equations to solve a given circuit, to obtain required current or voltage values.
Define and label voltage drop/rise at nodes Use KCL to analyze Analysis Methods Define and label current flow in a loop Mesh Use KVL to analyze Nodal

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.1

Introduction

Methods of analysis in solving any resistive circuit with current and voltage sources required knowledge in KCL, KVL and Ohms Law. Remember: By passive sign convention, current flows from high potential to low potential as it crosses a resistor.

vhigher vlower R

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.2

Nodal Analysis (Without Voltage Sources)

Based on application of KCL Has 2 types: 1. Circuits without voltage sources. 2. Circuits with voltage sources. Uses nodal voltages as circuit variables.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.2

Nodal Analysis (Without Voltage Sources)

Steps to Determine Nodal Voltage: 1. Select a node as the _____________________ (usually ground. 2. Assign voltages v1, v2, , vn-1 to the remaining n 1 node. The voltages are referenced with respect to the reference node. 3. Apply ______ to each of the n-1 non-reference nodes. Use Ohms Law to express the branch currents in terms of node voltages. 4. Solve the resulting simultaneous equations to obtain the unknown node voltages.
Last Updated: 17/07/2013 6

I-Station Solutions Sdn Bhd

3.2

Nodal Analysis (Without Voltage Sources)

Common symbols for reference nodes:

PP 3.1 PP 3.2

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.3

Nodal Analysis (With Voltage Sources)

Case 1: A voltage source connected between reference node and non-reference node.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.3

Nodal Analysis (With Voltage Sources)

Case 2: A voltage source connected between 2 non-reference nodes.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

3.3

Nodal Analysis (With Voltage Sources)

A supernode is formed by enclosing a (dependent or independent) voltage source connected between 2 nonreference nodes & any elements connected in parallel with it.

Properties: 1. Voltage source inside supernode provides a constraint equation needed to solve for node voltages. 2. Supernode has no voltage of its own. 3. Supernode required application of both KCL and KVL.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

10

3.3

Nodal Analysis (With Voltage Sources)

How to determine node voltage: 1. Take off all voltage sources (and any element in parallel with it) in supernodes and apply KCL to supernodes. 2. Put voltage sources back to the nodes and apply KVL to relative loops (supernode loops).

PP 3.3 3.4

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

11

3.4

Mesh Analysis (Without Current Sources)

A mesh is a loop which does not contain any other loops within it. Example: Paths abef and bcde are meshes. Path abcdef is not a mesh. Based on application of KVL. Has 2 types: 1. Circuits without current sources. 2. Circuits with current sources. Use mesh currents as circuit variables.
I-Station Solutions Sdn Bhd 12

Last Updated: 17/07/2013

3.4

Mesh Analysis (Without Current Sources)

Steps to determine mesh currents: 1. Assign currents _____________________ to the n meshes. 2. Apply ______ to each of the n meshes. Use Ohms law to express the voltages in terms of mesh currents. 3. Solve the resulting n simultaneous equations to obtain the unknown mesh currents.

PP 3.5 3.6

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

13

3.5

Mesh Analysis (With Current Sources)

Case 1: A current source exists only in one mesh.

i2 = -5A
Last Updated: 17/07/2013 I-Station Solutions Sdn Bhd 14

3.5

Mesh Analysis (With Current Sources)

Case 2: A current source exists between 2 meshes.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

15

3.5

Mesh Analysis (With Current Sources)

Supermesh is formed when two meshes have a (dependent or independent) current source in common and include any elements connected in series with it. Properties: 1. Current source inside supermesh provides a constraint equation needed to solve for mesh currents. 2. Supermesh has no currents of its own. 3. Supermesh requires application of both KVL and KCL.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

16

3.5

Mesh Analysis (With Current Sources)

How to determine mesh currents: 1. Take off all current sources (and any elements in series with it) in the supermesh & apply KCL to supermesh. 2. Put current sources back to the nodes and apply KCL to supermesh nodes.

PP 3.7

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

17

References
Alexander & Sadiku, Fundamentals of Electrical Circuits, 4th Edition, McGraw-Hill Company.

Last Updated: 17/07/2013

I-Station Solutions Sdn Bhd

18

You might also like