11.mechanical Properties of Materials

MECHANICAL PROPERTIES OF MATERIALS
Engineers are primarily concerned with the
development and design of machines, structures etc.
These products are often subjected to forces/
deformations, resulting in stresses/strains, the properties of materials under the action of forces and deformations becomes an important engineering consideration.
The properties of materials when subjected to
stresses and strains are called mechanical properties. In other words the properties that determine the behavior of engineering mats under applied forces are called mechanical properties.
The response of a material to applied forces depends on the type and nature of the bond and the structural arrangement of atoms, molecules or ions.
Basic deformation types for load carrying
materials are:
1. Elastic deformation (deformations are
instantaneously recoverable) 2. Plastic deformation (non-recoverable) 3. Viscous deformation (time dependent deformation)
Elastic Deformation
1. Initial 2. Load
bonds stretch return to initial shape
3. Unload
d
F
Return to the original shape when the applied load is removed. Elastic means reversible!
Linearelastic
Non-Linearelastic
Plastic Deformation
1. Initial 2. Load
bonds stretch & planes shear
3. Unload
p lanes still sheared
delastic + plastic
dplastic
F F
Could not return to the original shape when the applied load is removed. Plastic means permanent!
linear elastic linear elastic
dplastic
delastic
Viscous Deformation
Plastic deformations in noncrystalline solids (as well as liquids) occurs by a viscous flow mechanism. Usually attributed to fluids. But solids may also behave like viscous materials under high temperature and pressure. Viscous materials deform steadily under stress. Deformations are time dependent.
Based on the abovementioned deformation characteristics, several material idealizations could be made. Such as:
1. 2. 3. 4. Elastic Materials Plastic Materials extensometer Elastoplastic Materials Viscoelastic Materials
specimen
1. Elastic Materials
Return to the their original shape when the applied load is removed.
Unloading Loading d
2. Plastic Materials
No deformation is observed up to a certain limit. Once the load passes this limit, permanent deformartions are observed.
P
Limit
Loading
Plastic deformation
Unloading
3. Elastoplastic Materials
Up to a limit shows elastic properties. Within this limit if the load is removed, returns to its original shape. If the load passes the limit, plastic deformations are observed.
P Elastic Limit
Plastic Elastic deformation deformation
4. Viscoelastic Material
Deformations are time-dependent.
P
Fast Loading-Unloading
Slow Loading-Unloading
ISOTROPIC and ANISTROPIC Materials
The physical properties of some substances depend on the crystallographic direction in which the measurements are taken. For example, the elastic modulus, the electrical conductivity, and index of refraction may have different values in the [100] and [111] directions. This directionality of properties is termed as anisotropy, and it is associated with the variance of atomic or ionic spacing with crystallographic direction. Substances in which the measured properties are independent of the direction of measurement are called isotropic.
Isotropic materials have the same
mechanical properties in all directions. Anisotropic materials show different behavior in different directions.
Isotropic Materials (METALS) Anisotropic Materials (WOOD)
1= 2
1 2
Hooke's Law
Hooke's Law: For elastic materials, stress is linearly proportional to strain and is independent of time. Modulus of Elasticity, E:
s E
Linearelastic
F s=Ee e F
simple tension test
For an anisotropic material, the linear equations
between stress and strain components will be given by the following six equations known as the Generalized Form of Hookes law.
xx = C11xx+C12yy+C13zz+C14xy+C15xz+C16yz yy = C21xx +C22yy+C33zz+........... zz = C31xx + C32yy+.......... xy = C41xx +........... xz = C51xx +........... yz = C61xx +...........
The six equations of Generalized Hookes Law can be written in matrix form:
Stresses
Elastic constants
Strains
Stress-strain relationships such as these are known as constitutive relations. It can be shown that C12=C21, C31=C13... Therefore, the number of elastic constants reduce to 21 for an anisotropic material. The number of independent elastic constants reduce to 2 for isotropic materials. In fact, there are 4 constants (E, , K, G) 2 of which are independent. Elastic constants
For an isotropic material the Generalized Hookes Law yields:
E, n and G are known as elastic constants.
ISOTROPIC MATERIAL in UNIAXIAL TENSION
ISOTROPIC MATERIAL in PURE SHEAR

11.mechanical Properties of Materials

Uploaded by

Copyright:

Available Formats

11.mechanical Properties of Materials

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

11.mechanical Properties of Materials

Uploaded by

Copyright:

Available Formats

What are the different types of material deformations?

What are elastic materials?

MECHANICAL PROPERTIES OF MATERIALS

Engineers are primarily concerned with the

development and design of machines, structures etc.

These products are often subjected to forces/

The properties of materials when subjected to

Basic deformation types for load carrying

1. Elastic deformation (deformations are

Plastic Elastic deformation deformation

ISOTROPIC and ANISTROPIC Materials

Isotropic materials have the same

For an anisotropic material, the linear equations

For an isotropic material the Generalized Hookes Law yields:

E, n and G are known as elastic constants.

ISOTROPIC MATERIAL in UNIAXIAL TENSION

ISOTROPIC MATERIAL in PURE SHEAR

You might also like