Scribd
Upload
89 views20 pages

016 Enabling RIP

RIP is a distance vector routing protocol that uses hop count as the metric for route selection. RIPv1 uses classful routing and broadcasts updates every 30 seconds, while RIPv2 uses classless routing, supports VLSM, manual summarization, and authentication. Enabling RIP involves starting the routing process with the router rip command, identifying participating networks with network commands, and verifying the configuration with show commands. The debug ip rip command displays information on RIP routing transactions.

Uploaded by

BAHRAIN1967
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
89 views20 pages

016 Enabling RIP

RIP is a distance vector routing protocol that uses hop count as the metric for route selection. RIPv1 uses classful routing and broadcasts updates every 30 seconds, while RIPv2 uses classless routing, supports VLSM, manual summarization, and authentication. Enabling RIP involves starting the routing process with the router rip command, identifying participating networks with network commands, and verifying the configuration with show commands. The debug ip rip command displays information on RIP routing transactions.

Uploaded by

BAHRAIN1967
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 20

WAN Connections

Enabling RIP

ICND1 v1.0-5-1

What Is a Routing Protocol?

Routing protocols are used between routers to determine paths and maintain routing tables. After the path is determined, a router can route a routed

Autonomous Systems: Interior or Exterior Routing Protocols

An autonomous system is a collection of networks under a common administrative domain. IGPs operate within an autonomous system. EGPs connect different autonomous systems.

Classes of Routing Protocols

Administrative Distance: Ranking Routes

Classful Routing Protocol


Classful routing protocols do not include the subnet mask with the route advertisement. Within the same network, consistency of the subnet masks is assumed. Summary routes are exchanged between foreign networks. These are examples of classful routing protocols:
RIPv1 IGRP

Classless Routing Protocol


Classless routing protocols include the subnet mask with the route advertisement. Classless routing protocols support a variable-length subnet mask (VLSM). Summary routes can be manually controlled within the network. These are examples of classless routing protocols:
RIPv2 EIGRP OSPF IS-IS

Distance Vector Routing Protocols

Routers pass periodic copies of their routing table to neighboring routers and accumulate distance vectors

Sources of Information and Discovering Routes

Routers discover the best path to destinations from each neighbor.

RIP Overview

Maximum is 16 equal-cost paths (default = 4) Hop-count metric selects the path Routes update every 30 seconds

RIPv1 and RIPv2 Comparison


RIPv1 Routing protocol Supports variable-length subnet mask? Sends the subnet mask along with the routing update? Addressing type Defined in Supports manual route summarization? Authentication support? Classful No No Broadcast RFC 1058 No No RIPv2 Classless Yes Yes Multicast RFCs 1721, 1722, and 2453 Yes Yes

IP Routing Configuration Tasks

Router configuration
Select routing protocols Specify networks or interfaces

RIP Configuration
Starts the RIP routing process

RouterX(config)# router rip

terX(config-router)# version 2

Enables RIP version 2

RouterX(config-router)# network network-number

Selects participating attached networks Requires a major classful network number

RIP Configuration Example

Verifying the RIP Configuration

Routing Protocol is "rip" Sending updates every 30 seconds, next due in 6 seconds Invalid after 180 seconds, hold down 180, flushed after 240 Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Redistributing: rip Default version control: send version 2, receive version 2 Interface Send Recv Triggered RIP Key-chain FastEthernet0/0 2 2 Serial0/0/2 2 2

Automatic network summarization is in effect Maximum path: 4 Routing for Networks: 10.0.0.0 172.16.0.0 Routing Information Sources: Gateway Distance Last Update 10.1.1.2 120 00:00:25 Distance: (default is 120) RouterA#

Displaying the IP Routing Table

RouterA# show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default U - per-user static route, o - ODR T - traffic engineered route Gateway of last resort is not set 172.16.0.0/24 is subnetted, 1 subnets 172.16.1.0 is directly connected, fastethernet0/0 10.0.0.0/24 is subnetted, 2 subnets 10.2.2.0 [120/1] via 10.1.1.2, 00:00:07, Serial0/0/2 10.1.1.0 is directly connected, Serial0/0/2 192.168.1.0/24 [120/2] via 10.1.1.2, 00:00:07, Serial0/0/2

C R C R

debug ip rip Command

RouterA# debug ip rip RIP protocol debugging is on RouterA# 00:06:24: RIP: received v1 update from 10.1.1.2 on Serial0/0/2 00:06:24: 10.2.2.0 in 1 hops 00:06:24: 192.168.1.0 in 2 hops 00:06:33: RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (172.16.1.1) 00:06:34: network 10.0.0.0, metric 1 00:06:34: network 192.168.1.0, metric 3 00:06:34: RIP: sending v1 update to 255.255.255.255 via Serial0/0/2 (10.1.1.1) 00:06:34: network 172.16.0.0, metric 1

Summary
Routing is the process by which items get from one location to another. Dynamic routing protocols determine how updates are conveyed, what knowledge is conveyed, when to convey knowledge, and how to locate recipients of the updates. A routing protocol that has a lower administrative value is more trustworthy than a protocol that has a higher administrative value. There are three classes of routing protocols: distance vector, link-state, and balanced hybrid. The ip classless command can be used to prevent a router from dropping a packet that is destined for an unknown subnetwork of a directly attached network if a default route is configured.

Summary (Cont.)
RIP is a distance vector routing protocol that uses hop count as the matrix for route selection and broadcasts updates every 30 seconds. RIPv1 uses classful routing protocol; RIPv2 uses classless routing protocol. RIPv2 supports VLSM, manual route summarization, and authentication; RIPv1 does not support these activities. To enable a dynamic routing protocol, first a routing protocol is selected, then IP network numbers are assigned without values being specified (except OSPF). The router command starts the routing process. The network command allows the routing process to determine which interfaces

Summary (Cont.)
The router RIP command selects RIP as the routing protocol. The network command identifies a participating attached network. The show ip command displays information about routing protocols and the routing table. The debug ip rip command displays information on RIP routing transactions.

You might also like