CSI Water Catalog 2013

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.
qxd 6/17/13 4:19 PM Page i
Product
Catalog
0613
This catalog has been prepared for the use of CSI Water Treatment Systems authorized Distributors, Dealers,
Sales Representatives and prospective customers. Its contents are not to be reproduced in any manner or
form without the expressed written consent of CSI Water Treatment Systems. Additional copies may be
available by calling CSIWater Treatment Systems at (419) 281-6829, sending requests by fax to
(419) 281-2375 or mailing to 710 Orange Street, Ashland, Ohio 44805. Possession of this catalog does not
necessarily constitute an offer to sell.
CSI Water Treatment Systems disclaims any errors or omissions not discovered during proof reading and
production. CSI Water Treatment Systems reserves the right to delete and/or make modifications to product
offerings and designs when deemed necessary without prior notice.
-i-
CSI Water Treatment, 710 Orange Street, Ashland, Ohio 44805 Phone (419) 281-6829 Toll Free 888-363-9434
2013 CSI FAX 419-281-2375 www.csih2o.com [email protected]
CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page ii
TAble OF CONTeNTS
I. INTRODUCTION
Contacting CSI Water Treatment Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Visiting CSI (Directions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Company Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
II. PRODUCTS SECTION

Cabinet & Two Tank Water Softeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Signature Duplex Water Softeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminatr Water Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Signature Duplex Terminatr Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
City Water Softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Optimizr - Combination Softener & Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Nitro Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Nitro Pro Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reactr Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16
Reactr VS Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Oxyclean Automatic Reactr Cleansing System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
Hydroxr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
HydroxrVS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24
Whole House & Upflow Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Filter Media Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Tannin/Hardness Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Nitrate/Sulfate Treatment System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cartridge Tank System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Ultra Filtration System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-31
Ultraviolet Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cartridge Housings & Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
AlwaysFresh POU Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Microline Reverse Osmosis System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Champ ProMax Reverse Osmosis Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Greensand Plus Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SharkSkin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Vortech Distribution System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Control Valves:
Signature Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Signature Series 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
CSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Signature Duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
WS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
III. COMMERCIAL
Commercial
Commercial
Commercial
Commercial
Commercial
Commercial
Project Data Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Water Softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-53
Water Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-55
Reactr System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56-57
Hydroxr System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-59
Reverse Osmosis Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60-61
- ii -
CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page iii
TAble OF CONTeNTS
IV. TEChNICAL
Reactr Technical Information Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63-77
Softener Technical Information Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-79
Filter Technical Information Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-81
Chemical Feeding Technical Information Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82-83
Tannin/Hardness Technical Information Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
R/O Technical Information Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Nitrate/Sulfate Technical Information Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86-87
U/V Technical Information Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Granular Activated Carbon Reduction Capability Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Water Use estimates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
estimating Flow Rate Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Plotting Service Flow Rates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Water Well Disinfection (Shock Chlorination Procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Softener Regeneration Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Problem Cause/effect/Remedy Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
CSI Water Treatment Freeboard Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Slot Opening equivalents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Mathematical Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Table of elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Softening & Sodium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Water Data & Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
environmental Hotlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Drinking Water Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103-107
V. PARTS LISTS & DIAgRAMS

Control Valve Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109-112
Softeners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113-118
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119-121
eliminatr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122-124
Tannin/Hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125-126
Nitrate/Sulfate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127-128
Ultraviolet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Reactr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130-133
Oxyclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
brine System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
3/4 Plastic bodied Meter (2510 & 5600) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Valves:
Signature Series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137-142
2510 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143-50
5600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151-156
5600SXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157-160
Meter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Plastic bypass Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
brass bypass Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
9000/9100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164-170
R/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
- iii -
CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 1
CONTACTING CSI WATeR TReATMeNT
Contacting Us Is Easy
Mailing & Shipping Address
CSI Water Treatment Systems
710 Orange St.
Ashland, Ohio 44805
Office hours
8:00 a.m. - 5:00 p.m.
eastern Time Zone - Monday through Friday
Telephone & Fax Numbers

(419)-281-6829
(888)-363-9434
(419)-281-2375 Fax
(Voice Mail is Active evenings & Weekends)
Internet Web Address

http://www.csih2o.com
general Email Address

[email protected]
-1-
VISITING OUR FACIlITY

We always love our current and prospective customers to come to Ashland for plant tours, training
or just a friendly visit! Just let us know ahead of time when you will be arriving so that the proper
people can make time to meet with you. Ashland is located in North Central Ohio at exit 186 off
Interstate 71 between Cleveland and Columbus. Drive time from Cleveland Hopkins Airport is about
60 minutes and about 90 minutes from Port Columbus Airport. For those who visited our facility prior
to January of 2008, please note that the CSI Water Treatment division moved to a new location on
Orange St. CSI Controls still operates out of the facility on Ohio St. These maps should help you get
right to our front door, however, should you get lost or need any other information just give us a call
at (419) 281-6829. Remember, our office hours are 8:00 a.m. - 5:00 p.m., Monday - Friday.
If your plans require an overnight in Ashland, we have a few different options.

Just off of Interstate 71 are:
Ashland Inn
(419) 281-8090
holiday Inn Express
(419) 281-2900
Days Inn
(419) 289-0101
In town by Ashland University:
Surrey Inn hotel
(419) 289-7700
-2-
CSI WATeR TReATMeNT COMPANY PROFIle

On September 1, 1995, bill Chandler, Jr. formally began CSI Water Treatment, a division of Chandler
Systems Inc.. As one of the co-founders of WaterSoft Inc., bill has brought his experience and innovation
to CSI that built one of the most successful water treatment companies in the industry.
After the sale of WaterSoft Inc. to Amtrol Inc., bill left to begin a new venture specializing in the manufacture of electrical control systems for the wastewater industry. located in Ashland, Ohio, CSI Controls grew
quickly and has become a major supplier of control panels, distributing its products through water systems
and sewage wholesale distributors.
Many controls customers knew bill and his expertise in water treatment and expressed a desire that he
begin a new residential and commercial water treatment manufacturing company. Shortly after, CSI Water
Treatment was born. bill knew that just assembling equipment would not be enough. An experienced technical support staff, along with innovative products were the keys to success in the past and would also be
in the future.
bill was able to acquire the talents of two water treatment professionals that had helped build WaterSoft
Inc. into the successful company it once was. Duane baney and Russ Norris, with a combined experience
of 60+ years in water treatment manufacturing, joined CSI Water Treatment in September of 1995.
Soon thereafter, CSI introduced an innovation in air injection technology the REACTR. The REACTR utilizes a manifold that combines air induction with free air release for the oxidation of Iron,
Manganese and Sulfur Gas.
An option for the REACTR called the OXYCLEAN has been developed to introduce chlorine automatically during the backwash cycle for cleaning of the system.
The REACTR and OXYCLEAN technology has evolved into a revolutionary product for almost unlimited levels of iron and sulfur gas reduction. The HYDROXR combines aggressive aeration with the oxidation power of hydrogen peroxide.
To further our treatment capabilities for any type of water pump system, CSI Water Treatment has developed REACTR VS and hYDROXR VS for constant pressure (variable speed) and jet type pumping
systems.
To enhance a quality product line, the Signature Series control valve was introduced to the market in
July of 2003. Combining advanced electronic technology with high flow rates and simple to use programming, this proprietary control valve adds uniqueness and functionality to all CSI Systems.
In June of 2008, CSI acquired WaterSoft Inc. from Amtrol to complete the full circle and began growing the
company into a formidable force distributing products primarily through plumbing wholesale/distributors.
by summer of 2012, CSI had introduced the NITRO & NITRO PRO single tank aeration systems to provide economical, water saving, non-chemical treatment of iron and sulfur. At the same time, the Signature
Series 2 control valve was released. The Signature Series 2 valve provides the power for the NITRO /
NITRO PRO and is also available for all CSI equipment. both products currently have several patents
pending.
CSI Water Treatment has been actively involved in the commercial/industrial water treatment market and
has carried over the REACTR technology into their full line of commercial products. Their forte has been
specially engineered systems, combining their expertise in both controls and water treatment.
CSI Water Treatment distributes its residential/commercial products through a network of wholesale distributors across the United States and into certain foreign markets as well.
They are dedicated to the improvement of water quality through innovative development of water treatment
products, design engineering services and educational programs to provide the utmost in quality and support to their valued customers.
-3-
PRODUCTS
Products
Section
-4-
PRODUCTS
Cabinet & Two Tank Water Softeners - Signature Valve
FEATURES
Signature Series or Signature Series 2 timeclock or
meter initiated controls
Advanced electronic Technology & Simple
Programming
Adjustable cycle times
CalendarDay Override (metered versions only)
battery back-Up
Independently operated inlet/outlet bypass valve
3/4" FNPT stainless steel yoke connection
1" FNPT stainless steel yoke connection (optional)
High Flow 1" distributor tube
"V" units feature enpress Vortech distributor plate
High Flow brine safety float assembly, overflow fitting,
grid plate, and brine well
Space saving 11 x 11, 15 x 17 and 18 x 40 brine
tanks available (optional)
Poly wound mineral tank
Other valve options available at an additional cost
It's An Affordable
Necessity!
Water hardness is actually dissolved
Save Soap, Appliances,

Soften Water
Clothing and energy
the Natural Way
CONDITIONED WATER SAVES MONEY
rock! Calcium and Magnesium can

cause scale build-up in pipes and hot
Add up what you now spend and see what you can save
Cost
water tanks, and cause laundry to come

out stiff and gray. When iron is present,
sinks, fixtures and clothes can be
stained or ruined. It takes more energy
Cost
Save
Cost
Water Heater Fuel Savings

(22% Gas / 17% electric)
Gas Heater Fuel
electric Heater
Save
Cost
Personal Care Items 25%

bar Soap, Shampoos and
Rinses, Razor blades,
Softener Chemicals
(Save 100%)
bath Oils, Skin Creams
T O TA l S
Save
ucts compared to soft water.

Soft water can prevent soap build up
and feel. Clothes are brighter and last
longer without deposits trapped in their
fabric. Water pipes and appliances run
more efficiently without scaling.
Save
Appliance Savings 25%

Maintenance, Depreciation
and Replacement
can use twice the amount of soaps,
and can give skin and hair a silky look
Save
Cost
and cost to heat hard water, plus you

detergents, shampoos and related prod-
Soap / Chemical Savings 70%

laundry Detergents, Fabric Softeners,
Pre-Soaks, bleach, Plus More
efficient Cleaning Saves Time
Clothing Savings 33%
Clothing budget
-5-
Cabinet & Two Tank Water Softeners - Signature Valve
Grains Capacity/Regeneration
**Salt Used/Regeneration (lbs)
9lbs./cu ft
PRODUCTS
General
Specifications
Two Tank
Cabinet
CT24
CT32
TS24
TS32
TS48
TS64
CM24
CM32
MS24
MS32
MS48
MS64
CT24V
CT32V
TS24V
TS32V
TS48V
TS64V
TS96V
TS128V
CM24V
CM32V
MS24V
MS32V
MS48V
MS64V
MS96V
MS128V
24,000
32,000
24,000
32,000
48,000
64,000
96,000
128,000
20,250
27,000
20,250
27,000
40,500
54,000
81,000
108,000
15,000
20,000
15,000
20,000
30,000
40,000
60,000
80,000
12.0
15.0
12.0
15.0
24.0
30.0
45.0
60.0
7.5
9.0
7.5
9.0
15.0
18.0
27.0
36.0
4.5
6.0
4.5
6.0
9.0
12.0
18.0
24.0
Maximum Raw Water

Hardness (Grains)
50
75
50
75
100
100
100
100
Maximum Clear Iron /

Manganese (ppm)
.75
1.0
.75
1.0
1.5
2.0
3.0
4.0
exchange Resin (cu ft.)

Gravel Underbedding
N/A
N/A
N/A
N/A
N/A
N/A
Mineral Tank (polyglass)
8x35
10x35
8x44
9x48
10x54
12x52
brine Tank (polyethylene

w/ grid & safety)
N/A
N/A
18x33
18x33
18x33
18x33
18x40
24x50
Service Flow Rate (gpm)*
8.0
11.0
8.0
10.0
11.0
12.0
14.0
16.0
backwash Flow Rate (gpm)
1.5
2.4
1.5
2.0
2.4
3.5
4.0
5.0
Backwash Flow Rate (gpm)

Vortech (V) Units
1.2
2.0
1.2
1.5
2.0
2.4
3.5
4.0
Gallons Used/Regeneration
79
98
79
90
101
140
164
189
gallons Used/Regeneration
Vortech (V) Units
69
88
69
78
90
117
148
161
23x14x45
23x14x45
88
100
Space Required
(DxWxH inches)
Approximate Shipping
Weight (pounds)
N/A
14x65
N/A
16x65
18x26x53 18x27x56 18x28x62 18x30x60 18x32x74 24x40x74

88
100
133
164
285
378
* The pressure drop does not exceed 15.0 psi at the service flow rate.
** Factory Salt Settings;
Non-Vortech Units - 15lbs./cuft.
Vortech (V) Units - 9lbs./cuft.
-6-
PRODUCTS
Signature Series Duplex Softeners

FEATURES
Up to 30% savings in water & salt by never needing soft
water reserve
Never runs out of soft water, twin tanks eliminate the risk of
untreated water bypass
easy installation with new injection molded, one-piece
Plug-N-Flow manifold
New lower cost finally makes twin demand softeners a
smart buy for every household
Simple, adjustable valve programming makes changing salt
setting & backwash/rinse duration easy to achieve peak
performance
No worries about time of day clock
easy to maintain because it uses standard Signature Series
valve parts
Features Vortech tank technology maximizing capacity
and efficiency
Simple 9volt battery back-up keeps electronic meter active
and will motor control valve to shut off position if in
regeneration during power failure.
General
Specifications
**Salt Used/Regeneration (lbs. per tank)
9 lbs./cu ft.
SD48
SD64
SD96
SD128
SD48V
SD64V
SD96V
SD128V
SD192V
24,000
32,000
48,000
64,000
96,000
10,250
27,000
40,500
54,000
81,000
15,000
20,000
30,000
40,000
60,000
12.0
15.0
24.0
30.0
45.0
7.5
9.0
15.0
18.0
27.0
4.5
6.0
9.0
12.0
18.0
Maximum Raw Water Hardness (grains)
50
75
100
100
100
Maximum Clear Iron/Manganese (ppm)
exchange Resin (cu. ft.) (per tank)
.75
1.0
1.5
2.0
3.0
Gravel Underbedding (per tank)
N/A
N/A
N/A
N/A
N/A
Mineral Tanks (polyglass)
(2) 8x44
brine Tank (polyethylene with grid & safety)
18x33
18x33
18x33
18x33
18x40
Service Flow Rate (gpm per active tank)*
8.0
10.0
11.0
12.0
14.0
1.5
2.0
2.4
3.5
4.0
Backwash Flow Rate (gpm) Vortech (V) Units
1.2
1.5
2.0
2.4
3.5
79
90
101
140
164
gallons Used/Regeneration Vortech (V) Units

Space Required (DxWxH inches)
(2) 9x48
(2) 10x54
(2) 12x52
(2) 14x65
69
78
90
117
148
18x34x52
18x34x56
18x36x62
18x40x60
18x44x73
139
169
237
299
462
Approximate Shipping Weight (pounds)

** Factory Salt Setting: 9lbs./cuft.
-7-
The TerminatR Water Treatment System - Signature Valve

PRODUCTS
FEATURES
eliminates hardness (Calcium & Magnesium)
eliminates Iron/Manganese stains and taste
Signature Series or Signature Series 2 timeclock or
meter initiated controls
Advanced electronic Technology & Simple programming
Calendar Day Override (metered versions only)
battery back-Up
Features enpress Vortech distributor plate
High capacity fine mesh cation exchange resin
High Flow brine safety float assembly, overflow fitting,
gridplate and brine well
Includes Res-up Resin Cleaner Dispenser
It's An Affordable
Necessity!
Water hardness is actually dissolved
rock! Calcium and Magnesium can cause
scale build-up in pipes and hot water
tanks, and cause laundry to come out stiff
Save Soap, Appliances,

Soften Water
Clothing and energy
the Natural Way
CONDITIONED WATER SAVES MONEY
Add up what you now spend and see what you can save
Cost
and gray. When iron is present, sinks, fixtures and clothes can be stained or ruined.
It takes more energy and cost to heat hard
Cost
water, plus you can use twice the amount

of soaps, detergents, shampoos and relat-
Cost
ed products compared to soft water.

Soft water can prevent soap build up
Cost
and can give skin and hair a silky look and

feel. Clothes are brighter and last longer
without deposits trapped in their fabric.
Water pipes and appliances run more efficiently without scaling.
Cost
Soap / Chemical Savings 70%

laundry Detergents, Fabric Softeners,
Pre-Soaks, bleach, Plus More
efficient Cleaning Saves Time
Clothing Savings 33%
Clothing budget
Appliance Savings 25%
Maintenance, Depreciation
and Replacement
Water Heater Fuel Savings
(22% Gas / 17% electric)
Gas Heater Fuel
electric Heater
Personal Care Items 25%
bar Soap, Shampoos and
Rinses, Razor blades,
Softener Chemicals
(Save 100%)
bath Oils, Skin Creams
Save
Save
Save
Save
Save
T O TA l S
-8-
PRODUCTS
The TerminatR Water Treatment System - Signature Valve
General
Specifications
**Salt Used/Regeneration (lbs.)
Two Tank
TSI32
TSI48
TSI64
TSI96
MSI32
MSI48
MSI64
MSI96
35,000
52,500
70,000
105,000
32,000
48,000
64,000
96,000
26,500
39,750
53,000
85,000
15.0
24.0
30.0
45.0
9.0
15.0
18.0
27.0
6.0
9.0
12.0
18.0
Maximum Raw Water

Hardness (grains)
75
100
100
100
Maximum Clear Iron /

Manganese (ppm)
15
20
20
20
exchange Resin (cu. ft.)
1.0
1.5
2.0
3.0
Mineral Tank (Vortech)
9x48
10x54
12x52
14x65
brine Tank (polyethylene

with grid & safety)
18x33
18x33
18x33
18x40
10.0
11.0
12.0
14.0
1.2
1.5
2.0
3.0
72
83
95
140
18x27x56
18x28x62
18x30x60
18x32x74
130
163
204
290
Space Required
(DxWxH inches)
Approximate Shipping
Weight (lbs.)
** Factory Salt Setting; 15lbs./cuft.
-9-
Signature Series Duplex TerminatR System
Up to 30% savings in water & salt by never needing

soft water reserve
Never runs out of soft water, twin tanks eliminate the
risk of untreated water bypass
easy installation with new injection molded, one-piece
Plug-N-Flow manifold
New lower cost finally makes twin demand softeners a
smart buy for every household
Simple, adjustable valve programming makes changing salt setting & backwash/rinse duration easy to
achieve peak performance
No worries about time of day clock
easy to maintain because it uses standard Signature
Series valve parts
Features Vortech tank technology maximizing
capacity and efficiency
Simple 9volt battery back-up keeps electronic meter
active and will motor control valve to shut off position if
in regeneration during power failure.
General
Specifications
**Salt Used/Regeneration (lbs. per tank)

SDI64
SDI96
SDI128
SDI192
35,000
52,500
70,000
105,000
32,000
48,000
64,000
96,000
26,500
39,750
53,000
85,000
15.0
24.0
30.0
45.0
9.0
15.0
18.0
27.0
6.0
9.0
12.0
18.0
75
100
100
100
Maximum Clear Iron/Manganese (ppm)
15
20
20
20
exchange Resin (cu. ft.) (per tank)
1.0
1.5
2.0
3.0
(2) 9x48
(2) 10x54
(2) 12x52
(2) 14x65
18x33
18x33
18x33
18x40
10.0
11.0
12.0
14.0
1.2
1.5
2.0
3.0
Mineral Tanks (Vortech)

Service Flow Rate (gpm per active tank)*
72
83
95
140
18x34x56
18x36x62
18x40x60
18x44x73
169
237
299
512
Approximate Shipping Weight (lbs.)
PRODUCTS
FEATURES
- 10 -
PRODUCTS
City Water Softener - Signature Valve

FEATURES
Reduces hardness (Calcium & Magnesium)
Reduces Chlorine, taste and odor
Signature Series or Signature Series 2 timeclock or meter
initiated controls
battery back-Up
High capacity cation exchange resin
Dome fill opening for ease of service
High Flow brine safety float assembly,
overflow fitting, grid plate, and brine well
Features enpress Vortech mid plate technology
General
Specifications
Two Tanks in One

TSC32-D
MSC32-D
TSC48-D
MSC48-D
Timed
Metered
Timed
Metered
Regeneration Type
Activated Carbon Media
.5 cu ft
.5 cu ft
1 cu ft
1 cu ft
Softening Capacity
27,000
27,000
40,500
40,500
9.0
9.0
15.0
15.0
Maximum Raw Water Hardness (gpg)
75
75
100
100
Maximum Raw Water Iron (ppm)
Intermittent Flow Rate (gpm)
10
10
Mineral Tank Size (inches)
10x54
10x54
13x54
13x54
Gallons Used / backwash
130
130
170
170
18x28x62
18x28x62
18x31x62
18x31x62
130
130
240
240

- 11 -
OpTimizR Combination Softener & Filter
Perfect for Filtering and Softening in ONe system

Features enpress Vortech mid plate technology
PRODUCTS
FEATURES
initiated controls
battery back-Up
Dome fill opening for ease of service
For Filter Media Options see Filter Media Guide (pg. 26)
General
Specifications
Two Tanks in One

TSF32-10D MSF32-10D TSF48-15D MSF48-15D
Regeneration Type
Timed
Metered
Timed
Metered
Filter Media Capacity
1 cu ft
1 cu ft
1.5 cu ft
1.5 cu ft
Softening Capacity
32,000
32,000
48,000
48,000
15.0
15.0
24.0
24.0
Intermittent Flow Rate (gpm)
10
10

Mineral Tank Size (inches)
10x65
10x65
13x65
13x65
130
130
170
170
18x28x73
18x28x73
18x31x73
18x31x73
126
126
182
182

- 12 -
PRODUCTS
NiTRO Treatment System

FEATURES
Proprietary Signature Series 2 control
valve with independently programmable air draw & backwash cycles saving
THOUSANDS of gallons of water per
year!!
Simplicity of a single tank aeration
system that can be used with any type
of well pump and system (standard
submersible, constant pressure, jet
pump)
Precise external air injection directly
into the media tank to help prevent
control valve fouling & for ease of service
9 volt battery back-up w/ drain line

shut off position if power fails during
backwash
Operates on low 12 vdc power
Smart blend media for efficient
reduction of iron, manganese, sulfur &
correction of low pH
Dome fill hole standard
enpress Vortech distributor plate
for exceptional backwashing capability
Independently operated inlet/outlet
bypass valve included w/ 3/4 FNPT
stainless steel yoke connection
1 FNPT stainless steel yoke connection (optional)
10
IRON
9
8
ppm
7
6
5
4
3
SULFUR
2
1
0
6.0
6.5
7.0
7.5
8.0
8.5
pH
General
Specifications
Filtration (See Filter Media
section for application
Filter Media Capacity (cu. ft.)
Series
NTF15
NTF25
Smart blend
1.5
2.5
10x54
13x54
Service Flow Rate - Continuous (gpm)
Service Flow Rate - Intermittent (gpm)
10
5.0
7.0

106
146
10x10x62
13x13x62
145
221
- 13 -
NiTRO pRO Treatment System

9 volt battery back-up w/ drain
line shut off position if power
fails during backwash
Proprietary Signature Series 2

control valve with TWeDO
(Twin electric Drive Operation)
function (patent pending) permitting pumpless injection of
chlorine or peroxide during
backwash using the ready-touse Oxyclean NP (optional)
Operates on low 12 vdc power

Smart blend media for efficient reduction of iron, manganese, sulfur & correction of
low pH
enpress Vortech distributor
plate for exceptional backwashing capability
Simplicity of a single tank aeration system that can be used

with any type of well pumping
system (standard submersible,
constant pressure, jet pump)
Independently operated
inlet/outlet bypass valve included w/ 3/4 FNPT stainless steel
yoke connection
Precise external air injection

directly into the media tank to
help prevent control valve fouling & for ease of service
10
PRODUCTS
FEATURES
1 FNPT stainless steel yoke

connection (optional)
IRON
9
8
ppm
7
6
5
4
3
SULFUR
2
1
0
6.0
6.5
7.0
7.5
8.0
8.5
pH
General
Specifications
Filtration (See Filter Media
section for application
Filter Media Capacity (cu. ft.)
Series
NTP15
NTP25
Smart blend
1.5
2.5
10x54
13x54
10
5.0
7.0
106
146
10x10x62
13x13x62
145
221

- 14 -
PRODUCTS
REACTR Treatment System

FEATURES
Signature Series or Signature Series 2 control valves
available
battery back-Up
High backwash flow capability
Poly wound REACTR Tank
large UT style aeration tank (optional)
The concept of air injection for the reduction of Iron, Manganese and Sulfur Gas is not new. In most
cases, these contaminants can be treated in this manner without the use of chemicals, such as Chlorine
or Potassium Permanganate.
CSI Water Treatment Systems reintroduces this technology with an innovative new approach - The
REACTR. Several new ideas are incorporated in the REACTR Water Treatment System. Air injection and free air venting are accomplished through a common manifold assembly which simplifies installation and service. The REACTR manifold assembly is mounted on a large air mixing tank that triples
the amount of air contact and exposure time. A full 1" FNPT inlet and outlet is provided to install the
REACTR tank between the well pump and pressure tank. This exposes the REACTR tank to full
pump flow for increased air draw, air mixing and reduced plugging problems. Oxidized contaminants
then enter the REACTR filter where they are removed by the Smart Blend filtration media.
Smart Blend is a proportioned mix of three proven filter medias to provide optimum performance
with wide application potential. The filter is automatically maintained by the CSI Signature Series or
Signature Series 2 control valves that provides the advantages of adjustable cycle times and high backwash flow capability in a high tech electronic valve with simple programming and battery back-up.
Combine all of these features with the benefits of no chemical treatment and you have the finest water
treatment system available on the market today - The REACTR!
Iron and Sulfur Removal
Manganese Removal
REACTR capability to remove Manganese from
water is critically dependent on the Iron and pH
levels as shown below:
If the Iron to
Manganese ratio is:
- 15 -
For effective Iron and Sulfur

removal, your ppm's must be on or
below
these curves
Then the pH must

be at least:
10:1
7.0
5:1
7.8
1:1
8.3
0:1
8.5
REACTR Treatment System
RF10
RF15
Filter Media Type
RF20
RF25
RF30
RF40
Smartblend
Filter Media Capacity (cu ft)
1.00
1.50
2.00
2.50
3.00
4.00
REACTR Tank (polyglass)
9x48
9x48
9X48
9x48
16x40
16x40
9x48
10x54
12X52
13x54
14x65
16x65
11

10
11
13
5.0
5.0
6.0
7.0
10.0
15.0
100
200
300
Space Required (DxWxH inches) REACTR Tank 9x9x62

Space Required (DxWxH inches) Filter Tank
Approximate Shipping Weight (lbs)
PRODUCTS
General
Specifications
9x9x56
133
100
120
140
9x9x62
9X9X62
9x9x62
16x16x51 16x16x51
10x10x62 12X12X60 13x13x62 14x14x73 16x16x74

165
236
270
311
394
Note: Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash requirement. Use of a flow
control in the Service line is highly recommended. Consult the factory or your field sales person with questions. Oxyclean can be added to
any existing Reactr or Reactr VS system.
Typical Installation
- 16 -
PRODUCTS
REACTR VS Treatment System

FEATURES
Designed for use with constant pressure (variable speed)
and jet type pumping systems
Quiet, high output, oil less air compressor for maximum
aeration
Signature Series or Signature Series 2 Control Valve with
meter for precise compressor control
Advanced electronic technology and simple programming
battery backup
Poly wound REACTR tank
large UT style aeration tank (optional)
With the advent of constant pressure (variable speed) pumping systems, CSI Water Treatment went
back to the drawing board to engineer a REACTR system that will effectively treat iron, manganese
and sulfur gas when a constant pressure well system is utilized - the REACTR VS.
The REACTR VS will work equally well for jet pump type systems, where typical air injection systems won't. Incorporating a quiet, high output, oil less air compressor, the REACTR VS
provides the aeration power for chemical free treatment of problem well water. For those really tough
jobs the REACTR VS is designed to add the Oxyclean option for chlorinating the entire system
every backwash cycle.
The Signature Series or Signature Series 2 control valves provide high backwash flow capabilities
and utilizes an integral contact flow meter for precise compressor control.
The REACTR VS system provides new technology treatment for new technology constant pressure pumping systems!
Manganese Removal

below
these curves
If the Iron to
Manganese ratio is:
- 17 -
Then the pH must

be at least:
10:1
7.0
5:1
7.8
1:1
8.3
0:1
8.5
REACTR VS Treatment System
RF10
RF15
RF20
1.00
1.50
2.00
9x48
9x48
9X48
9x48
16x40
16x40
9x48
10x54
12X52
13x54
14x65
16x65
11
10
11
13
Filter Media Type
RF25
RF30
RF40
3.00
4.00
Smartblend
2.50
5.0
5.0
6.0
7.0
10.0
15.0
100
100
120
140
200
300
9x9x62
9X9X62
9x9x62
Space Required (DxWxH inches) REACTRTank
9x9x62
9x9x56
PRODUCTS
General
Specifications
143
16x16x51 16x16x51
10x10x62 12X12X60 13x13x62 14x14x73 16x16x74

175
246
280
321
404
control in the Service line is highly recommended. Consult the factory or your field sales person with questions.
Oxyclean can be added to any existing Reactr or Reactr VS System.
- 18 -
PRODUCTS
The OXYCLEANAutomatic REACTRCleansing System
FEATURES
Automatically cleans the entire REACTR system
with every backwash
Ideal for situations where media bed becomes
fouled by high levels of ferric iron, iron or
sulfur bacteria* and tannins*
Installs in minutes
Can be added to any existing REACTR system
without changes to the plumbing or electrical wiring
effectively uses chlorine* or hydrogen peroxide*
No pump adjustments required
No pump check valves to maintain
CSI first introduced the REACTR, a truly innovative chemical free oxidation system for the reduction of
iron, manganese and sulfur gas. Now after extensive research and development CSI is proud to introduce the
OXYCLEAN Automatic REACTR Cleansing System. A system that will enhance the operating performance of a REACTR installed on exceptionally poor water quality situations. Situations that are normally
tough to handle and require a high level of maintenance can now be solved with the OXYCLEAN
Automatic Cleansing System.
Plugged pipes and fouled media beds can be the result of low levels of iron or sulfur bacteria*, tannins*
and high levels of ferric iron. Many times these situations require a messy, time consuming service call. The
OXYCLEAN Automatic Cleansing System can reduce these types of calls.
Installed in minutes the OXYCLEAN System will automatically inject chlorine* or hydrogen peroxide*
during every backwash to clean the entire REACTR system and associated plumbing such as inlet plumbing, tank tees, etc.
every REACTR System built has the optional OXYCLEAN in mind, installation is easy and can be
done during or after installation of the REACTR without any changes to the plumbing or electrical wiring.
Install the REACTR with the OXYCLEAN Automatic Cleansing System today and reduce those
annoying service calls tomorrow.
* Not to be substituted for accepted disinfection techniques for moderate or high levels of these contaminants.
- 19 -
The OXYCLEANAutomatic REACTRCleansing System

PRODUCTS
- 20 -
PRODUCTS
The HydroxR Aeration / Peroxide System

FEATURES
Combines aggressive pressurized aeration with the
oxidation power of hydrogen peroxide (H2O2)
For treatment of virtually unlimited levels of iron,
manganese and sulfur gas
(see limitation matrix chart)
Disinfection properties with added contact time for iron,

manganese and sulfur bacteria control
Includes reliable peristaltic chemical feed pump package for
self-priming operation
Signature Series or Signature Series 2 Control Valve
Advanced electronic technology and simple programming
battery backup
Independently operated inlet / outlet bypass valve
Poly wound HydroxR and mineral tank
CSI Water Treatment Systems first introduced a truly revolutionary product for the reduction of iron, manganese, and sulfur gas - the REACTR.
Now CSI unveils a system that combines the aggressive pressurized aeration technology of REACTR
with the oxidation power of hydrogen peroxide for treatment of virtually unlimited levels of iron, manganese
and sulfur gas - the HydroxR!
At the same time, bacteriological forms of these constituents are controlled without the creation of chemical
byproducts, contact tanks or the on going maintenance of rebedding carbon filters.
The included chemical feed pump package is of a peristaltic design for self-priming operation.
Add the advanced electronic technology and features of the Signature Series or Signature Series 2
control valves and you have a system that will provide capabilities for problem water treatment that you never
thought possible - the HydroxR!
Manganese Removal
HydroxR capability to remove Manganese from

For effective Iron and Sulfur removal, your

ppm's must be on or below these curves
100
- 21 -
5:1
7.0
1:1
7.8
0:1
8.3
40
N
IRO
60
ppm
be at least:
UR
Manganese ratio is:
Then the pH must
lF
SU
If the Iron to
80
20
6 6.5
7 7.5 8 8.3 8.5

ph
The HydroxR Aeration / Peroxide System
UTP15
UTP20
Filter Media Type

UTP25
UTP30
UTP40
Smartblend
1.50
2.00
2.50
3.00
4.00
10x54
12x52
13x54
14x65
16X65
11
10
11
13
5.0
6.0
7.0
10.0
15.0
100
120
140
200
300
Space Required (DxWxH inches) HydroxR Tank
21x21x74 21x21x74 21x21x74 21x21x74 21x21x74
10x10x62 12X12X60 13x13x62 14x14x73 16x16x74
PRODUCTS
General
Specifications
Space Required (DxWxH inches) Feed Pump System 17x17x28.5 17x17x28.5 17x17x28.5 17x17x28.5 17x17x28.5
175
246
280
321
394
Note: Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash requirement.
Use of a flow control in the Service line is highly recommended. Consult the factory or your field sales person with questions.
- 22 -
PRODUCTS
The HydroxR VS Peroxide System

FEATURES
Specifically designed for use with constant pressure
(variable speed) and jet style pumping systems

where treatment of extreme levels of iron, manganese and sulfur gas is required
Disinfection properties with added contact time for
iron, manganese and sulfur bacteria control
Includes reliable peristaltic chemical feed pump
package for self-priming operation
Signature Series or Signature Series 2 control
valves with built in contact flow meter for precise
metering of hydrogen peroxide & compressor control
Advanced electronic technology and simple
programming
battery backup
Independently operated inlet / outlet bypass valve
Poly wound HydroxR and mineral tank
With the advent of constant pressure (variable speed) pumping systems, CSI Water Treatment went back to
the drawing board to engineer a HydroxR System that will effectively treat extreme levels of iron, manganese
and sulfur gas when a constant pressure well system is utilized - the HydroxR VS.
The HydroxR VS will work equally well for jet pump type systems, where typical air injection systems won't.
The Signature Series or Signature Series 2 control valves provide high backwash flow capabilities and utilizes an integral contact flow meter for precise injection of hydrogen peroxide and compressor control no matter
what the flow rate.
The large HydroxR VS contact tank provides the necessary time for adequate disinfection of iron,
manganese and sulfur bacteria.
The HydroxR VS System provides new technology treatment for new technology constant pressure
pumping systems!
Manganese Removal
HydroxR capability to remove Manganese from

100
- 23 -
5:1
7.0
1:1
7.8
0:1
8.3
40
IRO
N
60
ppm
be at least:
UR
Manganese ratio is:
Then the pH must
lF
SU
If the Iron to
80
20
6 6.5
7 7.5 8 8.3 8.5

ph
The HydroxR VS Peroxide System
UTP15VS UTP20VS UTP25VS UTP30VS UTP40VS
Filter Media Type

Smartblend
1.50
2.00
2.50
3.00
4.00
10x54
12x52
13x54
14x65
16x65
11
10
11
13
5.0
6.0
7.0
10.0
15.0
100
120
140
200
300
Space Required (DxWxH in.) HydroxR VS Tank
21x21x74 21x21x74 21x21x74 21x21x74 21x21x74
Space Required (DxWxH in.) Filter Tank
10x10x62 12X12X60 13x13x62 14x14x73 16x16x74
Space Required (DxWxH in.) Feed Pump System

PRODUCTS
General
Specifications
17x17x28.5 17x17x28.5 17x17x28.5 17x17x28.5 17x17x28.5

175 246
280
321
394
Note: Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash requirement. Use
of a flow control in the Service line is highly recommended. Consult the factory or your field sales person with questions.
- 24 -
PRODUCTS
Whole House & Upflow Filters - Signature Valve

FEATURES
battery back-Up
Upflow filter includes 1" FNPT manifold with bypass
valve included
Optional dome fill hole and closure
Optional "natural" color
enpress Vortech distributor plate - Provides
vigorous backwash with no gravel underbed needed!
SeRIeS
General
Specifications
WF10
WF15
WF20
WF25
U10
U15
U20
U25
Filtration1
(see "Filter Media" section for applications)
WF30
WF40
Less Filter media
1.00
9x48
1.50
2.00
10x54
12x52
2.50
3.00
4.00
13x54
14x65
16x65
Service Flow Rate - Continuous2 (gpm)
11
Service Flow Rate - Intermittent2 (gpm)
10
11
13
backwash Flow
Rate3
(gpm) "WF" units only
Gallons Used / backwash "WF" units only

Space Required (DxWxH in.)
5.0
5.0
6.0
7.0
10.0
15.0
100
100
120
140
200
300
WF
9x9x56
10x10x62 12x12x60 13x13x62 14x14x74 16x16x74
9x9x52
10x10x58 12x12x56 13x13x58
N/A
N/A
WF
27
32
35
40
49
54
20
25
30
35
N/A
N/A
Note 1: See "Filter Media" section for selection of proper media for your filtration application. Note 2: Use of a flow control in the Service
line is highly recommended. Note 3: Caution should always be used in sizing filters! Always choose a unit by first satisfying the Backwash
requirement. Consult the factory or your field sales person with questions.
- 25 -
Filter Media Selection Guide
Media
Description
Handles
Neutralizer
Granular / White / Sacrificial to water with pH < 7.0 / Max pH correction to 7.2 /
Sediment (downflow)
lowest pH application 5.8 / Must be replenished about every 3-6 months
pH Correction
Semi-round / Off-White / Magnesium Oxide / extremely reactive to pH dissolving
Sediment (downflow)
rapidly adding alkalinity / 30% Corosex - 70% Neutralizer is best blend for
pH Correction
Corosex
PRODUCTS
Filter Media Selection Guide
correcting low pH / Will raise pH from lows around 5.0 to as high as 9.0+ /
Must be replenished frequently / Consult factory with specific application questions
Neu-Cor
70% neutralizer / 30% Corosex mix. Sacrificial to water with any pH / max pH
Sediment (downflow)
correction determined by contact time used for correction of extremely low pH
pH correction
down to 5.0 / Must be replenished every 3-6 months.

Granular
Granular / black / Wide application for removal of organics and some inorganics /
Sediment (downflow)
Activated
Must be replaced on a regular basis / life expectancy varies based on use
Taste / Odor / Color
Carbon
birm
Filter Ag
Chlorine / Iodine
Granular / Gray / Must not be used on waters with a pH < 6.8 / Must have
Sediment
dissolved oxygen present at a level of at least 15% of Iron & Manganese ppm /
Iron (clear & red)
Max Iron & Manganese level 10ppm / estimated life about 8-10 years
Manganese (clear & red)
Granular / Off-White / Wide application for removal of sediment /
Sediment
life expectancy is unlimited

Filter Ag
light tan to near white in color/Mesh size 14x40/55lb/ft3 / The Filter Ag Plus filter beds
enhanced Particle Removal
Plus
operate at less than half the hydraulic loading rate vs. 20x40 mesh sand and 50% of
(Down to 5 microns)
sand/anthracite or multi-media
Smart
blend
Granular / White-black / blend of Neutralizer, Filter Ag & Manganese Dioxide

Max life expectancy about 8-10 years but is dependent upon pH
Sediment
Iron (clear & red)
Manganese (clear & red)
Sulfur Particles
pH Correction
"D" Gravel
Semi-Round / brown / #20 Flint / Used as underbed for Non-Vortech Filters
Underbed
providing for excellent flow distribution in both service and backwash modes /
Permanent unless fouled but can be cleaned and reused
Filter media and gravel is shipped in convenient reusable buckets.
- 26 -
PRODUCTS
Tannin / Hardness Treatment System - Signature Valve

FEATURES
Reduces hardness (Calcium & Magnesium)
Reduces Tannin stains, taste and odor
initiated controls
battery back-Up
High capacity Tannin Anion exchange resin
Features enpress Vortech Distributor plate
General
Specifications
Grains Capacity / Hardness Regeneration
Two Tank
TST32
TST48
TST64
MST32
MST48
MST64
24,000
32,000
48,000
**Salt Used / Regeneration (lbs.)
12.0
15.0
24.0
50
75
100
Maximum Clear Iron / Manganese (ppm)
.50
.50
.50
.75
1.0
1.5
Tannin Resin (cu. ft.)
.25
.50
.50
9x48
10x54
12x52
18x33
18x33
18x33
10.0
11.0
12.0
1.2
1.5
2.0
Gallons Used / Regeneration
69
80
93
18x27x56
18x28x62
18x30x60
100
133
164


**Factory Salt Setting; 15lbs./cuft.
- 27 -
Nitrate / Sulfate Treatment System - Signature Valve

PRODUCTS
FEATURES
Reduces Nitrates (ePA MCl* 10.0 mg/l)
Reduces Sulfates (ePA SMCl** 250 mg/l)
Reduces Fluoride (ePA MCl* 4.0 mg/l)
Signature Series or Signature Series 2 time clock or meter
initiated controls
battery back-Up
High capacity Nitrate Selective Anion exchange resin
Features enpress Vortech Distributor plate
* MCl Maximum recommended primary contaminant level

** SMCl Maximum recommended secondary contaminant level
General
Specifications
Grains Capacity / Regeneration
Maximum Raw Water Nitrate /Sulfate (mg/l)
Salt Used / Regeneration (lbs.)
TN15
TN25
MN15
MN25
15,000
25,000
100
100
18.0
30.0
1.5
2.5
10x54
13x54
18x33
18x33
Service Flow Rate (gpm)
5.0
8.0
1.2
2.4
60
80
18x28x62
18x31x62
133
251
- 28 -
Cartridge Tank Systems & Filters
FEATURES
Designed to treat the full flow
of the home (up to 40 gpm)
Simple Filter changes without tools
No backwash wastewater
Compact - 8D x 42H
Commercial size available 2 in/out (up to 135 gpm)
NSF Standard 61 listed
150psi working pressure
Cartridge Tanks
General
Specifications
CTF8
CTF8-HF
Color
black
black
Inlet / Outlet (in.)
1.25
Maximum Flow Rate (gpm)
40
135
Cartridge Dimensions (in.)
8D x 42H
8D x 42H
Carbon Block Filters for Taste/Odor Removal & Sediment

General
Specifications
CT-03-Cb
(blue)
Micron Rating
Treatment Dsicription
CT-20-Cb
(blue)
CT-03-Cb-AMINe
CT-ACP
(Red-High Flow only)
20
Chlorine/Sediment
Chlorine/Sediment
Chlorine/Sediment
Chlorine/Sediment
40/10
70/7
40/10
15/1
Max Flow Rate/psi drop
Filters for Sediment Removal

General
Specifications
Micron Rating
Treatment Description
Max Flow Rate/psi drop
CT-1005
(orange)
10x5
Sediment
28/3
CT-2005
CT-2010
20x5
20x10
SWMb
(yellow)
(orange)
Sediment Sediment
40/10
30/3
CT-2020 CT-20NANO
CT-P1A
CT-P5
CT-P20
(orange)
AG
(green)
(Red-High
Flow only)
(Red-High
Flow only)
(Red-High
Flow only)
20x20
20x20
Absolute 1
20
Sediment Fine Sed.

30/3
35/9
Sed/Cyst Sediment Sediment

100/15
125/10
135/7
- 29 -
Ultra Filtration System - Signature Valve
FEATURES
Filtration down to .02 micron - excellent for organic color
(tannins), Colloidal Clay, Virus, bacteria & Cyst Reduction
UF8 Model utilizes the Signature Series Control Valve for
automatic backwash of the UF membrane
UF8C Model utilizes the Signature Series Shuttle Valve
System to provide automatic clean water backwash of the
UF membranes and tank flushing (a pressure tank(s) with
10-12 gals. draw down is required and are not included)
Membranes are NSF Standard 61 Certified
Tank is NSF Standard 44 Certified
General
Specifications
UF8**
UF8C**
Micron Rating
.02
.02
Pre-Filtration Required (microns)
<5
<5

Service Flow Rate (gpm)
10
10
2.0*
2.0
10
10
8 x 8 x 50
8 x 14 x 56
46
46
*A manual High Flow backwash Valve is supplied to flush tank once per week at a minimum flow of 5.0 gpm
for 2 minutes.
**See Point-of-Use Application/Site Profile Form (pg. 31). This form must be completed and sent to CSI
with 12-16 ounces of water for required bench testing. Failure to do so relieves CSI of All functional liability.
- 30 -
PRODUCTS
Point-of-Use Application/Site Profile

Contact Information
Customer :
Address :
City / State :
Phone :
Distributor :
Other pertinent notes :
Date :
Dealer Contact :
Phone :
Fax :
Email :
System Parameters
Application :
Size / Type :
Design Flow (GPM) :
Average Flow (GPM) :
Gallons per day usage :
Est. Gallons per year :
Sulfide Odor:
Existing treatment at location :
(Residential, other POE, commercial, other)

(Single family, multiple family, multiple dwelling)
(Max design flow rate)
(Typical demand)
(Average throughput per day)
(Best estimate)
Yes / No (If yes, describe treatment)
Water Analysis (enter all available)

*** Tannin :
** Sulfides :
(*E Coli, Coliform, Fecal Coliform, Cysts, etc.)
Iron :
mg/L as CaCO3 Manganese :
Hardness :
units
TDS:
*** Color :
* Must be tested by certified laboratory (copy of analysis report must be included)
** Must be field tested if H2S odor present
*** Two (12) oz. water samples must be sent - one for analysis and one
for bench testing. Please label samples accordingly.
pH :
*Pathogenic Organisms :
mg/l
mg/l
mg/l
mg/l
mg/l
Complete and send with water sample to :

CSI Water Treatment
710 Orange Street
Ashland, Ohio 44805
(888) 363-9434
(419) 281-6829
CSI Equipment Recommendation ***

CSI Distributor :
Pretreatment equipment recommendation :
- 31 -
Ultraviolet Disinfection Systems
Benefits of Ultraviolet
Viqua Features
Provides protection against illness
From 5gpm to 47gpm
No harmful chemicals or byproducts
High Output UV lamps
No alteration of taste or water quality
Unique Water Chamber Design
Simple to install and maintain
New Power Supply Technology
economical to operate
Viqua UV Max reminds you to replace

the lamp
New UV Intensity Monitoring Device
5yr. Warranty on units and 1yr. Warranty
on lamps
General
Specifications
UVMAXC4 UVMAXD4 UVMAXe4 UVMAXF4
PRO10
PRO20
PRO30
lamp
602805
602805
602806
602807
602854
602855
602856
Sleeve
602732
602732
602733
602734
602974
602975
602976
10
20
30
Max GPM
15
25
Inlet/Outlet
3/4" NPT
3/4" NPT
1" NPT
1" NPT
Failure Alarm
NSF Approved
Chamber
29 x 3.5in. 43.5 x 3.5in.
21.4 x 4in.
31 x 4in.
41 x 4in.
Optional
Optional
Optional
Optional
UV Intensity Monitor
Cool Touch Kit
FailSafe Solenoid Shut-off
19.5 x 3.5in. 19.5 x 3.5in.
1 1/4" NPT 1 1/4" NPT 1 1/4" NPT
Optional
Optional
- 32 -
PRODUCTS
Cartridge Housings & Filters

FEATURES
NSF / ANSI Standard 42 for material &
structural integrity
Reinforced polypropylene
excellent chemical resistance
Max Temperature 125F
Max Pressure 125psi
Filter housings
General
Specifications
Color
Inlet / Outlet (in.)
Threads
Pressure Relief button
Case Quantity
CH10
CH10C
CH10J
CH20
Opaque
Clear
Opaque
3/4 FPT
3/4 FPT
1 FPT
Plastic
Plastic
Plastic
Plastic
Plastic
2.5 x 10
2.5 x 10
4.5 x 10
2.5 x 20
4.5 x 20
12
12
Opaque
3/4 FPT
CH20J
Opaque
1 FPT
*Mounting brackets & sump wrenches are available for all models.
Carbon Block Filters for Taste and Odor Removal

General
Specifications
Micron
Case Quantity
Cb10
Cb10J
Cb20
Cb20J
2.5 x 10
4.5 x 10
2.5 x 20
4.5 x 20
20
20
Melt Blown Filters for Sediment Removal

General
Specifications
Micron
Case Quantity
Mb510
Mb510J
Mb2010
Mb2010J
Mb520
Mb520J
Mb2020
Mb2020J
20
20
20
20
2.5 x 10
4.5 x 10
2.5 x 10
4.5 x 10
2.5 x 20
4.5 x 20
2.5 x 20
4.5 x 20
40
12
40
12
20
20
- 33 -
AlwaysFresh POU Filters
NSF/ANSI Standard 42 & 53 validated by

Water Quality Association (WQA Gold Seal)
PRODUCTS
FEATURES
Treats all cold water at kitchen faucet with no
waste water to drain
Quick change cartridges with no disassembly
required
DWS-HFC-1000 System utilizes RC-HFC1000 5-Stage filtration cartridges, reducing
Chlorine, Chloramine, lead, VOCs, TTHMs,
MTbe, CYSTS, & Turbidity
Commercial models available
Filter Systems & Filter head Kits

General
Specifications
Flow Rate (gpm)
Replacement Cartridge
# of Filter Heads
Approx Dimensions
DWS-HFC-1000
HFH-38QC-KIT
HFH-38QC-SS HFH -38QC-SS

2P-KIT
2S-KIT
1.5
1.5
1.5
1.5
RC-HFC-1000
Non Included
Non Included
Non Included
2-Parallel
2-Series
4 x 4 x 21
4 x 4 x 21
4 x 4 x 21
4 x 4 x 21
(with Cartridge)
(with Cartridge)
(with Cartridge)
*Triple Head Series or parallel kits available
Always Fresh Replacement Cartridges

General
Specifications
Micron Rating
Treatment Purpose
Capacity (gal.)
RC-HFC-1000
RC-HF-20000
(commercial)
.50
.50
chlorine, chloramines,
lead, VOCs, THM,
MTbe, Cyst, turbidity
chlorine, Cyst, turbidity
1000
20,000
Melt Blown Filters for Sediment Removal

General
Specifications
Micron Rating
Treatment Purpose
Capacity (gal.)
RC-DSX-212
RC-Fl-1000
N/A
N/A
Scale Control
Fluoride
N/A
500
*Other specialty cartridges available - Contact factory for details
- 34 -
PRODUCTS
MICROlINe Reverse Osmosis System
FEATURES
WQA S-300-91 Validated & NSF Validated
Chromed long reach air gap faucet
Water saving shut-off valve
Pressure boost pump (optional)
Precharged storage tank
TFC-4 includes an additional polishing
filter for taste and odor removal
Quality Water for a Quality lifestyle

Reverse Osmosis (R.O.) is one of the most convenient and economical methods of reducing unwanted contaminants in your drinking water. Reverse Osmosis is the process by which water molecules are forced, by water pressure, through a semipermeable
membrane. Most of the impurities and other contaminants are rinsed to the drain while the refined water is routed to a special
holding tank.
The Microline TFC-3 & TFC-4 Reverse Osmosis Drinking Water Systems use the latest advances in plastics technology to
produce the most streamlined and user friendly R.O. systems on the market. What sets the Microline apart from other systems is
its patented design. Injection molded from FDA compliant materials, the system directs the flow of the water through each filtration
step without the need for tubes or fittings. This design also contains major component parts like the water saving automatic shut-off,
drain control and safety check valve, making it easy to maintain and service.
Another Microline innovation is its patented membrane seal. This feature makes membrane replacement a snap without the
need for tools. The Microline Reverse Osmosis Drinking Water System is validated by the National Sanitation Foundation (NSF)
Water Quality Association (WQA) under Industry Standard S-300-91 and by the state of Wisconsin's Department of Industry, labor
and Human Relations. let Microline provide the quality water you deserve you'll taste the difference.
General Specifications
Membrane
Production
Rating1
41 - 53 gallons/day
TDS Reduction
96% minimum
14 gallons/day
System
Warm2
Production
Rating
Climate
TDS Reduction
Water Pressure (min/max)

Maximum Raw Water TDS (ppm)
Temperature Range (min/max)
pH Range
93% Typical
40-100 psi
2,000
40100 F
4.011.0
Maximum Hardness (grains)
<10
Maximum Iron (ppm)
< 0.1
Maximum Manganese (ppm)
<0.05
Maximum Hydrogen Sulfide (ppm)
None
Chlorine Range (min/max)3

bacteria4
Replacement Prefilter Number
None
Must be Potable
PRe-GAC
Replacement Membrane Number
MM-TFC
Replacement Postfilter Number
PST-GAC
In-line Activated Carbon Filter

Space Required (DxWxH)
Note
Note
Note
Note
- 35 -
Microline TFC-3 & TFC-4
1:
2:
3:
4:
MPOlJG
12 x 20 x 18
25
Measured at Industry Standard condition of 65 psi, 77 F, 250 TDS and discharging to atmosphere.
Actual capacity measured at 50 psi, 77 F, and 750 TDS.
Chlorinated feed water must not come into contact with TFC membranes.
Do not use where the feed water is microbiologically unsafe or with water of unknown quality without adequate
disinfection before or after the unit.
Champ PuROMax Reverse Osmosis System
PuROMax
PRODUCTS
FEATURES
5 Stage 50 GPD R/O
High Flow 3/8 Delivery
NSF Approved QC Fittings
NSF Approved Tank
Color Coded Tubing
Complete Install Kit
Reverse osmosis processes water at the molecular level.

by squeezing ordinary tap water against a special
membrane, pure water molecules are separated from
impurities. These impurities are automatically rinsed
down the drain leaving only clean great tasting water.
Nominal Rejection Rates for typical R/O units
Aluminum ..........................................96-98%
Arsenic ..............................................94-96%
bacteria ................................................99+%
barium ...............................................96-98%
Cadmium ...........................................95-97%
Calcium .............................................94-97%
Chlorine .............................................90-95%
Chloride .............................................90-95%
Copper...............................................96-98%
Cyanide .............................................90-95%
Fluoride .............................................93-95%
Replacement Filter Description
5 micron Sediment Pre-Filter
5 micron Carbon block Pre- Filter
Carbon Post Filter
Inline Carbon Filter
Filter Kit less Membrane
50 gpd TFC Membrane
lead ..................................................96-98%
Magnesium ........................................95-98%
Manganese........................................94-96%
Mercury .............................................95-97%
Nitrate ................................................92-95%
Phosphate .........................................97-98%
Silver .................................................95-97%
Sodium ..............................................94-98%
Zinc....................................................96-98%
Part Number
Mb510
Cb10
UDF10
IAC10
PC5-FlT
S1764
- 36 -
PRODUCTS
Greensand plus Filters

FEATURES
Adjustable cycles
battery back-Up
Includes KMNO4 feed pot with grid platform
and float shutoff
General
Specifications
IF10
Filter Media
Garnet Sand Underbed (lbs.)
IF15
IF25
1.00
1.50
2.00
2.50
20
30
50
50
9x48
10x54
Potassium Permanganate Solution

Tank Size
Removal Capacities Iron / Sulfur
IF20
Greensand Plus
12x52
13x54
10x16
10 ppm / 3 ppm 10 ppm / 3 ppm 10 ppm / 3 ppm 10 ppm / 3 ppm
10
5.0
5.0
6.0
7.0
128
130
173
193
9x21x57
10x22x62
13x24x60
12x25x62
215
305
362
157
control in the Service line is highly recommended. Consult the factory or your field sales person with questions.
- 37 -
Accessories
Chemical Feed Equipment
Water Treatment
Chemicals & Additives
PRODUCTS
Test kits, Test Strips, ph/TDS

Meters & Replacement Chemicals
Media Funnels,
Flow Controls & Tubing
Mineral Extractors
- 38 -
PRODUCTS
Shark Skin Jacket
FEATURES
easy to apply with a quick zip
No need to remove valve or plumbing
Insulates tank
No more condensation
No more puddles on floor
Can be applied to most media tank sizes
Order separately from equipment black Color Only
Item Number
SK9J
Description
SharkSkin Jacket - 1.0 cf - for 9x48Tank
SK10J
SK134J
SK135J
- 39 -
Vortech Distribution System

PRODUCTS
Vortech Bottom
Plate Distributor
High Flow Vortech
The newest, innovative and most efficient bottom distribution system. Cleaning is greatly improved,
freeboard is reduced, and it works with all softening and filtration medias. The Vortechs high flow design
maximizes todays high efficiency valves.
The new Vortech Technology replaces conventional distributor tube and basket systems. No gravel underbed
required. Garnet underbed used only on Greensand Plus Iron Filters.
FEATURES
Permanent attachment of dip tube to distributor, so when servicing a valve, distributor stays in place.
elimination of gravel, save on net cost and unit weight for shipping.
Improved system pressure drop characteristics.

Increase softening capacity, due to improved flow through media.
No channeling of media, providing a cleaner more efficient system.
environmentally friendly, reduction in required backwash times due to improved bed lift and mixing at
lower flow rates.
Most efficient softening regeneration, reducing salt consumption.
- 40 -
PRODUCTS
10 - 7 - 5 - 1
LIMITED WARRANTY
Water Treatment equipment
During the time periods and subject to the conditions hereinafter set forth, CSI Water Treatment, will repair or replace to the original user or
consumer, any portion of your new CSI Water Treatment product which proves defective due to defective materials or workmanship of CSI
Water Treatment. Contact your nearest authorized CSI Water Treatment dealer for warranty service. At all times CSI Water Treatment shall
have and possess the sole right and option to determine whether to repair or replace defective equipment, parts, or components. Damage due
to conditions beyond the control of CSI Water Treatment is NOT COVERED BY ThIS WARRANTY. (Contact parcel or freight company for
claims on freight damage in transit.)
WARRANTY PERIODS:
Item
Residential Mineral Tanks
Commercial Mineral Tanks
Proprietary Control Valves
Other Softener/Filter Control Valves
Brine Tank (30 or smaller)
Brine Tank (39 or larger
*10 yrs *7 yrs *5 yrs *1 yrs
Item
*5 yrs
Brine Tank Components

MicroLine Reverse Osmosis Systems
Other Residential RO Systems
Other Accessories and Parts
Commercial Reverse Osmosis - 1 year from ship date
Pumps & membranes are pro-rated per month
*1 yrs
LABOR, ETC., COSTS: CSI Water Treatment shall IN NO EVENT be responsible or liable for the cost of field labor or other charges incurred
by any customer removing and/or reaffixing any CSI Water Treatment product, part or component thereof.
ThIS WARRANTY WILL NOT APPLY: (a) To defects or malfunctions resulting from failure to properly install, operate or maintain the unit
in accordance with printed instructions provided; (b) to failures resulting from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units which are not installed in accordance with applicable local codes, ordinances
and good trade practices; (e) if the unit is moved from its original installation location; (f) unit is used for purposes other than for what it was
designed and manufactured, and (g) filter media and exchange resins.
RETURN OF REPLACED COMPONENTS: Any item to be replaced under this Warranty must be returned to CSI Water Treatment in Ashland,
Ohio, or such other place as CSI Water Treatment may designate, freight prepaid.
PRODUCT IMPROVEMENTS: CSI Water Treatment reserves the right to change or improve its products or any portions thereof without being
obliged to provide such change or improvement of units sold and/or shipped prior to such change or improvement.
WARRANTY EXCLUSIONS: As to any specific CSI Water Treatment product, after the expiration of the time period of the warranty applicable
thereto as set forth under the heading Warranty Periods above, ThERE WILL BE NO WARRANTIES, INCLUDINg ANY IMPLIED WARRANTIES OF MERChANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. No warranties or representations at any time made by any representative of CSI Water Treatment shall vary or expand the provisions hereof.
LIABILITY LIMITATION : IN NO EVENT ShALL CSI WATER TREATMENT BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAgES RESULTINg FROM OR RELATED IN ANY MANNER TO ANY CSI WATER TREATMENT PRODUCT
OR PARTS ThEREOF.
Some states do not allow the exclusion of limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
The Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
In the absence of suitable proof of installation date, the effective date of this warranty will be based upon the date the manufacture plus thirty
(30) days.
Direct all notices, etc. To: Service Department, CSI Water Treatment, 710 Orange Street, Ashland, Ohio 44805
Date: October 2011
- 41 -
PRODUCTS
Control
Valves
The following section describes the specifications and key features of the Control
Valves offered by CSI Water Treatment Inc. The Signature Series is the standard control specified and shipped on all units that have a Timeclock or Demand Initiated control
valve with the exception of the Signature Duplex System.
Other control valves are available upon request but have varying order numbers and
possible price differences. Please consult your Distributor, Field Sales Representative
or contact the factory with specific questions.
- 42 -
PRODUCTS
Signature Series Control Valve

Valve Specifications
Valve material
Noryl*
Inlet/Outlet
3/4, 1
Cycles
Flow Rates (50 psi Inlet) - Valve Alone

Continuous (15 psi drop)
21 GPM
Peak (25 psi drop)
27 GPM
CV (flow at 1 psi drop)
5.4
Max. backwash (25 psi drop)
17 GPM
Regeneration
Downflow/Upflow
Downflow
Adjustable cycles
Yes
Time available
99 minutes per cycle
Meter Information
Product Features
Meter accuracy range
.25 - 15 GPM +/- 5%
12 VDC operation
Meter capacity range (gal.)
1 - 9,999
5 cycles, all fully adjustable
Programming ease and options increase efficiency, save

salt and water
Downflow or upflow regenerations
Strong, durable Noryl valve body, weather-resistant

enclosure
Demand regeneration or timeclock versions and filters
Timed brine refill
battery back-Up
Visual Indication of Valve Position
Switch Output for:

- Full Cycle Function
- backwash Function
limited 7 year warranty
Dimensions
Distributor pilot
1.050 O.D.
Drain line
1/2 NPT Q.C.
brine line
3/8
Mounting base
2-1/2 - 8 NPSM
Height from top of tank
7.7
Typical Applications
Water softener
6-16 diameter up to
3
4 ft. capacity
Iron filter
6-16 diameter
Sediment filter
6-16 diameter
Carbon filter
6-16 diameter
Neutralizing filter
6-16 diameter
Options
Additional Information
bypass valve (Noryl or Stainless Steel)
electrical rating
12 VDC
backwash filter
Pressure
Hydrostatic: 300 psi
Meter initiated regeneration
Working: 20 - 125 psi

Temperature
34 - 110 F
*Noryl is a registered trademark of General electric Company.
- 43 -
Signature Series 2 Control Valve
Valve material
Noryl*
Inlet/Outlet
3/4, 1
Cycles
PRODUCTS

21 GPM
Peak (25 psi drop)
27 GPM
5.4
17 GPM
Regeneration
Downflow/Upflow
Downflow
Adjustable cycles
Yes
Time available
99 minutes per cycle
Meter Information
.25 - 15 GPM +/- 5%
1 - 9,999
Dimensions
Product Features
12 VDC operation
5 cycles, all fully adjustable
Programming ease and options increase efficiency,

save salt and water
Distributor pilot
1.050 O.D.
Drain line
1/2 NPT Q.C.
brine line
3/8
Mounting base
2-1/2 - 8 NPSM
7.7
Downflow or upflow regenerations
Strong, durable Noryl valve body, weather/insect
Water softener
6-16 diameter up to
3
4 ft. capacity
resistant one-piece slide cover
Demand regeneration or timeclock versions and filters
Iron filter
6-16 diameter
9V battery back-up
Sediment filter
6-16 diameter
Will motor to a drain line shut off position if power fails
Carbon filter
6-16 diameter
during regeneration
Neutralizing filter
6-16 diameter
Switch Output for:
- Full Cycle Function
- backwash Function
electrical rating
12 VDC
Pressure
limited 7 year warranty
Options
Temperature
34 - 110 F
bypass valve (Noryl or Stainless Steel)
backwash filter
Nitro & Nitro Pro Single Tank Aeration Systems
- 44 -
PRODUCTS
CSA
Valve material
Noryl*
Inlet/Outlet
3/4, 1
Cycles

20 GPM
Peak (25 psi drop)
26 GPM
5.0
7 GPM
Regeneration
Downflow/Upflow
Downflow
Adjustable cycles
brine flow only
Time available
180 minutes
Meter Information
.25 - 15 GPM +/- 5%
Standard: 125 - 2,125

extended: 625 - 10,625
Dimensions
Product Features
Simple mechanical design is easy to understand
Injector/drain modules containing the brine valve,
flow controls and injector are removable from the
valves exterior
Distributor pilot
1.050pipe O.D.
Drain line
1/2 NPTF
brine line
3/8
Mounting base
2-1/2 - 8 NPSM
Water softener
6-12 diameter
Iron filter
6-13 diameter
CSA controls are user friendly and easy to program
Sediment filter
6-13diameter
Non-corrosive, UV-resistant Noryl valve body
Carbon filter
6-13 diameter
Choice of 12 day clock or demand regeneration with
Neutralizing filter
6-13 diameter
Ruggedly built timer is designed with heavy-duty 3/8

wide plastic gears
mechanical meter
economical small annual power consumption;
electrical rating
115 v / 60 Hz
keeps the time and activates the piston/valve
Max. VA
mechanics with a single motor
estimated shipping weight
Time clock: 5 lbs.
Options
Metered valve: 6 lbs.

Pressure
bypass valve (Noryl or stainless steel)

backwash filter
Auxiliary switches

Temperature
34 - 110 F

**As defined in the Safe Drinking Water Act.
- 45 -
Signature Series Duplex Control Valve
Noryl*
3/4, 1
6
PRODUCTS
Valve material
Inlet/Outlet
Cycles
Flow Rates (50 psi Inlet) - Valve With Meter

18.2
Peak (25 psi drop)
23.5
4.7
8.5
Product Features
Salt and water savings by using 100% capacity of the
Regeneration
Downflow/Upflow
Adjustable cycles
Downflow only
Yes
Meter Information
0.25 - 15 GPM +/- 5%

1 - 9,999
Dimensions
Distributor pilot
Drain line
brine line
Mounting base
1.05 O.D.
1/2 NPT
3/8
2-1/2 - 8 NPSM
7.7
Water softener
6-14 diameter
tank in service, before switching to the second tank

Regenerates immediately when needed for continuous
soft water
Regenerates with soft water and keeps system clean for
optimum operating efficiency and minimum maintenance
Proven technology and performance
Corrosion-free Noryl* valve body
Most parts common to the Signature Valve
Simple to service and maintain
Displays current flow rate
9volt battery back-up will motor valve to shut off position
& keeps meter active during power failure
No time clock to set
Adjustable cycles
Options
Noryl or stainless steel bypass valve
electrical rating
estimated shipping weight
Pressure
Temperature
12vdc
12.0 lbs
34 - 110 F
- 46 -
PRODUCTS
Clack WS1 Control Valve

Valve material
Noryl*
Inlet/Outlet
3/4, 1 or 1-1/4
Cycles

27 GPM
Peak (25 psi drop)
35 GPM
7.0
27 GPM
Regeneration
Product Features
Solid State microprocessor with easy access front
panel settings
Downflow/Upflow
Downflow
Adjustable cycles
Yes
Meter Information
.25 - 27 GPM +/- 5%
20 - 50,000
Three modes of operation; meter immediate, meter

delayed, or time clock delayed
Dimensions
Double backwash feature offers optimum regeneration,

cleaning ability, and efficiency
Distributor pilot
1.050 O.D.
Drain line
3/4 or 1 NPT
brine line
3/8 or 1/2 OD Poly Tube
Mounting base
2-1/2 - 8 NPSM
7.375
66 selectable pre-programmed regeneration cycles

Days override feature; 1-28 days available
backwash and brining ability to 22 diameter tanks
Downflow / Upflow regeneration
Stores system configuration and operation data in non
volatile memory
Capacitor back-up with up to 2 hour power carry over
12-volt output AC adapter provides safe and easy
installation
Control valve design provides optimum service and
backwash rates
Treated water regenerant refill
Reliable and proven DC drive
Options
bypass valve (Noryl)
backwash filter
Water softener
6-22 diameter up to
3
7 ft. capacity
Iron filter
6-22 diameter
Sediment filter
6-22 diameter
Carbon filter
6-22 diameter
Neutralizing filter
6-22 diameter
electrical rating
12 VAC
Pressure
Temperature
40 - 110 F
- 47 -
COMMERCIAL
Commercial
& Industrial
Products
The following section is a brief selection of some of the more popular commercial products. A complete commercial catalog is available to qualifying customers. Please see
your Distributor or Field Representative for complete information on our Commercial &
Industrial products and design services.
- 48 -
Commercial Project Data Form
0 1&232&4 2
0 41&5 &3 54
# $ 0 41&5 &52
666
5
"# $
&
%&
&
&
&
&
&
& )'/
&(
*
#
! "
COMMERCIAL
'
!
"# $
'
'( .
%&
#% #
(
+
!
"# $
( -( &
%&
) * +
!
"# $
!"
# $
"
# %%+ ,
"
% &
7!*
'
!
#'(
&
('
%&
/ !)
0"
! +
7 "
&
"# $
& '
%&
1
*
1
2
!1 #%
&
&
*
" 3
&
&
23
+,-./
!$ ! 4
0
&
+- . 8
;!
9 6
.
98 8
( 0 % 8
1 ' 9<
*0
. 6
':% '*%)'
- 49 -
Single Tank Water Softeners

STANDARD FEATURES
OPTIONS
Clean Water backwash
No Hard Water bypass
2750, 2850, 2900, or 3900 Top-mount
Control Valves
electro-Mechanical Control Valve
Steel and ASMe rated Pressure Vessels
Mechanical Flow Meter
Side-mount Control Valves
Flow Management with Motorized ball Valves or
Staged Diaphragm Valves
Water Quality Monitor Initiated Regeneration
High Capacity Resin
TYPICAL USE:
boiler Feed
Cooling Tower
Schools
light Industrial
Hotels/Motels
Apartments
Nursing Home/ Assisted living
Condominiums
Car/Truck Wash
Corporate Campus
Hospitals
COMMERCIAL
High Flow Control Valves thru 3 Flow Rates 200+ gpm

Up to 1.2 Million Grain Tank Capacity per Tank
Maximum Operating Pressure 125 psi/110 F
Clack Control Valves
Time Clock or electronic Meter Regeneration
Premium Cation Resin 30K grains/cu.ft.
Hard Water bypass
brine Tank HDPe material, Salt Grid Plate or
Gravel Underbed, Safety brine Valve (30 & smaller diameter),
Air Check and Overflow
Automatically reduce hardness (calcium/magnesium) and dissolved iron/manganese along with their unpleasant side-effects.
Only the highest quality resin, controls and materials are used in
CSI Commercial Water Softeners. Our motor-driven piston control valve is the most reliable under even severe water conditions
and resists common adversaries such as hardness and iron.
Meanwhile, our hub and lateral style or Vortech distribution
systems within the corrosion resistant tanks maximize flow while
reducing pressure loss through the units. Designed for use in
commercial, industrial or domestic water applications.
As we remain Committed to Innovation, CSI provides the
design and engineering support to ensure the most effective
treatment solution for each installation. For a stand-alone installation or a new construction project, replace or integrate new
equipment into an existing process, we have the proper system
options available to meet your needs.
- 50 -
GPM FLOW RATES
COMMERCIAL
Model No.
CTS60-10WS
CTS60-12WS
CTS60-15WS
CMS60-10WS
CMS60-12WS
CMS60-15WS
CTS90-10WS
CTS90-12WS
CTS90-15WS
CMS90-10WS
CMS90-12WS
CMS90-15WS
CTS120-10WS
CTS120-12WS
CTS120-15WS
CTS120-20WS
CMS120-10WS
CMS120-12WS
CMS120-15WS
CMS120-20WS
CTS150-12WS
CTS150-15WS
CTS150-20WS
CMS150-12WS
CMS150-15WS
CMS150-20WS
CTS210-15WS
CTS210-20WS
CMS210-15WS
CMS210-20WS
CTS300-15WS
CTS300-20WS
CMS300-15WS
CMS300-20WS
CTS450-20WS
CTS450-30WS
CMS450-20WS
CMS450-30WS
CTS600-20WS
CTS600-30WS
CMS600-20WS
CMS600-30WS
CTS900-30WS
CMS900-30WS
CTS1200-30WS
CMS1200-30WS
SERVICE
PEAK
15 PSI
Loss
8 PSI
Loss
25 PSI
Loss
21
27
37
20
26
36
20
25
35
19
24
34
21
26
40
47
20
25
39
46
28
44
53
27
43
52
50
66
48
65
53
73
51
71
84
144
81
138
93
172
89
163
187
175
194
181
15
20
27
15
19
26
15
18
26
14
18
25
15
19
29
34
15
18
28
34
20
32
39
20
31
38
37
48
35
47
39
53
37
52
61
105
59
101
68
126
65
119
137
128
142
132
28
35
48
27
35
47
27
34
46
26
33
45
28
35
52
60
27
34
51
59
37
57
69
35
55
68
64
85
62
83
68
94
65
91
109
186
105
179
119
222
114
210
242
227
251
234
PIPE SIZE
NPT
BACK
WASH
SERVICE
DRAIN
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
4.2
5.3
5.3
5.3
5.3
5.3
5.3
5.3
5.3
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
13
13
13
13
20
20
20
20
30
30
30
30
40
40
50
50
1"
1-1/4"
1-1/2"
1"
1-1/4"
1-1/2"
1"
1-1/4"
1-1/2"
1"
1-1/4"
1-1/2"
1"
1-1/4"
1-1/2"
2"
1"
1-1/4"
1-1/2"
2"
1-1/4"
1-1/2"
2"
1-1/4"
1-1/2"
2"
1-1/2"
2"
1-1/2"
2"
1-1/2"
2"
1-1/2"
2"
2"
3"
2"
3"
2"
3"
2"
3"
3"
3"
3"
3"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"
1"
1"
1"
1"
1"
1-1/2"
1"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
2"
OPERATINg INFORMATION
GRAINS EXCH CAP

@ LBS SALT
MAXIMUM
MINIMUM
RESIN TANK
BRINE TANK
CU.FT. RESIN
DIA X HT
SALT CAPACITY
LBS
DIA X HT
60,000 GR @ 30 #
40,000 GR @ 12 #
14" x 65"
18" x 40"
300
90,000 GR @ 45 #
60,000 GR @ 18 #
14" x 65"
18" x 40"
300
120,000 GR @ 60 #
80,000 GR @ 24 #
16" x 65"
24" x 50"
700
150,000 GR @ 75 #
100,000 GR @ 30 #
18" x 65"
24" x 50"
700
210,000 GR @ 105 #
140,000 GR @ 42 #
21" x 62"
24" x 50"
700
300,000 GR @ 150 #
200,000 GR @ 60 #
24" x 72"
10
30" x 50"
1000
450,000 GR @ 225 #
300,000 GR @ 90 #
30" x 72"
15
30" x 50"
1000
600,000 GR @ 300 #
400,000 GR @ 120 #
36" x 72"
20
42" x 60"
2900
900,000 GR @ 450 #
600,000 GR @ 180 #
42" x 72"
30
50" x 60"
4100
1,200,000 GR @ 600 #
800,000 GR @ 240 #
48" x 72"
40
50" x 60"
4100
For use on Potable Water Only

Do not use on microbiologically unsafe or unknown quality water
Installation must comply with state and local plumbing/electrical codes
120v/24v CUl/Ul listed transformer included with electronic meter systems
Tank warranty void if subject to vacuum
low flow channeling less than .5 gpm/cu. ft. resin may cause hardness leakage
Water Temperature Range

Ambient Air Temperature Range
Operating Pressure Range
electronic Requirements
Influent Turbidity
Influent Chlorine
Iron/Manganese
OVERALL
HEIGHT
Single Tank Water Softener Specifications
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
73"
74"
73"
73"
73"
74"
76"
75"
76"
76"
75"
76"
75"
76"
75"
76"
82"
83"
82"
83"
86"
89"
86"
89"
98"
101"
98"
101"
102"
102"
101"
101"
35 110F
35 120F
20 125 psi
110v/60Hz
5 NTU
1 ppm max.
< 5 ppm
- 51 -
Multi-Tank Water Softeners

STANDARD FEATURES
OPTIONS
COMMERCIAL
High Flow Control Valves thru 3 Flow Rates 700+ gpm

Up to 1.2 Million Grain Tank Capacity per Tank
electronic Meter Regeneration
Duplex Alternating Tank Operation
Triplex & Quadplex Progressive Flow Operation
Premium Cation Resin 30K grains/cu.ft.
No Hard Water bypass
brine Tank HDPe material, Salt Grid Plate or
Gravel Underbed, Safety brine Valve (30 &
smaller diameter), Air Check and Overflow

electro-Mechanical Control Valve
Steel and ASMe Rated Pressure Vessels
Flow Management with Motorized ball Valves
or Staged Diaphragm Valves
Water Quality Monitor Initiated Regeneration
High Capacity Resin
2900, 3900, 9000, or 9500 Top-mount Control Valves
TYPICAL USE
boiler Feed
Hospitals
large Schools and Universities
Industrial Pre-treatment
Hotels/Motels
Apartments/Condos
laundry Facilities
Food Service
Corporate Park
Automatically reduce hardness (calcium/magnesium) and

dissolved iron/ manganese along with their unpleasant
side-effects. Only the highest quality resin, controls and
materials are used in CSI Commercial Water Softeners.
Our motor-driven piston control valve is the most reliable
under even severe water conditions and resists common
adversaries such as hardness and iron. Meanwhile, our
hub and lateral style or Vortech distribution system within the corrosion resistant tanks maximize flow while reducing pressure loss through the units. Designed for use in
commercial, industrial or domestic water applications.
design and engineering support to ensure the most effective treatment solution for each installation. For a standalone installation or a new construction project, replace or
integrate new equipment into an existing process, we have
the proper system options available to meet your needs.
- 52 -
SERVICE*
COMMERCIAL
15 PSI
Loss
8 PSI
Loss
PEAK*
25 PSI
Loss
BACK
WASH
SERVICE
DRAIN
GRAINS EXCH CAP

@ LBS SALT
(PER RESIN TANK)
MAXIMUM
MINIMUM
CAT60-10WS
20
15
27
4.2
1"
3/4"
60,000 GR @ 30 #
CAT60-12WS
26
19
35
4.2
1-1/4"
3/4"
40,000 GR @ 12 #
CAT60-15WS
36
26
47
4.2
1-1/2"
3/4"
CAT90-10WS
19
14
26
4.2
1"
3/4"
90,000 GR @ 45 #
CAT90-12WS
24
18
33
4.2
1-1/4"
3/4"
60,000 GR @ 18 #
CAT90-15WS
34
25
45
4.2
1-1/2"
3/4"
CAT120-10WS
20
15
27
5.3
1"
3/4"
CAT120-12WS
25
18
34
5.3
1-1/4"
3/4"
120,000 GR @ 60 #
80,000 GR @ 24 #
CAT120-15WS
39
28
51
5.3
1-1/2"
3/4"
CAT120-20WS
46
34
59
5.3
2"
3/4"
CAT150-12WS
27
20
35
7.5
1-1/2"
3/4"
CAT150-15WS
43
31
55
7.5
1-1/2"
3/4"
150,000 GR @ 75 #
CAT150-20WS
52
38
68
7.5
2"
3/4"
100,000 GR @ 30 #
CMS150-203QWSH
108
78
140
7
2"
1"
CMS150-204QWSH
162
117
210
7
2"
1"
CAT210-15WS
48
35
62
10
1-1/2"
1"
CAT210-20WS
65
47
83
10
2"
1"
210,000 GR @ 105 #
140,000 GR @ 42 #
CMS210-203QWSH
136
100
176
10
2"
1"
CMS210-204QWSH
204
150
264
10
2"
1"
CAT300-15WS
51
37
65
13
1-1/2"
1"
CAT300-20WS
71
52
91
13
2"
1"
300,000 GR @ 150 #
200,000 GR @ 60 #
CMS300-203QWSH
150
110
194
12
2"
1"
CMS300-204QWSH
225
165
291
12
2"
1"
CAT450-20WS
81
59
105
20
2"
1"
CAT450-30WS
138
101
179
20
3"
1-1/2"
CMS450-203QWSH
176
128
226
20
2"
1"
450,000 GR @ 225 #
300,000 GR @ 90 #
CMS450-204QWSH
264
192
339
20
2"
1"
CMS450-303QWS
276
202
358
20
3"
1-1/2"
CMS450-304QWS
414
303
537
20
3"
1-1/2"
CAT600-20WS
89
65
114
30
2"
1-1/2"
CAT600-30WS
163
119
210
30
3"
1-1/2"
CMS600-203QWSH
194
142
252
30
2"
1-1/2"
600,000 GR @ 300 #
400,000 GR @ 120 #
CMS600-204QWSH
291
213
378
30
2"
1-1/2"
CMS600-303QWS
326
238
420
30
3"
1-1/2"
CMS600-304QWS
489
357
630
30
3"
1-1/2"
CAT900-30WS
175
128
227
40
3"
2"
900,000 GR @ 450 #
CMS900-303QWS
350
256
454
40
3"
2"
600,000 GR @ 180 #
CMS900-304QWS
525
384
681
40
3"
2"
CAT1200-30WS
181
132
234
50
3"
2"
1,200,000 GR @ 600 #
CMS1200-303QWS
362
264
468
50
3"
2"
800,000 GR @ 240 #
CMS1200-304QWS
543
396
702
50
3"
2"
*Flow rates shown are minimum possible at all times (they're assuming one tank is off-line for regeneration).
RESIN TANK
BRINE TANK
CU.FT. RESIN
(Per TANK)
SALT CAPACITY
LBS Per TANK
DIA X HT
14" x 65"
14" x 65"
16" x 65"
18" x 65"
21" x 62"
24" x 72"
10
30" x 72"
15
36" x 72"
20
42" x 72"
30
48" x 72"
40
2
2
2
2
2
2
2
2
2
2
2
2
2
3
4
2
2
3
4
2
2
3
4
2
2
3
4
3
4
2
2
3
4
3
4
2
3
4
2
3
4
QTY
Model No.
PIPE SIZE
NPT
QTY
GPM FLOW RATES
DIA X HT
18" x 40"
300
18" x 40"
300
24" x 50"
700
24" x 50"
700
24" x 50"
700
30" x 50"
1000
30" x 50"
1000
42" x 60"
2900
50" x 60"
4100
50" x 60"
4100
2
2
2
2
2
2
2
2
2
2
2
2
2
3
4
2
2
3
4
2
2
3
4
2
2
3
4
3
4
2
2
3
4
3
4
2
3
4
2
3
4
OVERALL
HEIGHT
Multi-Tank Water Softener Specifications
73"
73"
73"
73"
73"
73"
73"
73"
73"
74"
76"
75"
76"
80"
80"
75"
76"
80"
80"
82"
83"
87"
87"
86"
89"
88"
88"
89"
89"
98"
101"
100"
100"
101"
101"
102"
102"
102"
101"
101"
101"
Duplex CAT-series - Twin Demand Alternating Tank Operation, 24v electronic timer and turbine meter
(One tank is in operation and one tank is in standby/regeneration at all times)
Triplex/Quad - QWS Progressive Flow electronic Phased Operation, 24v electronic timer and turbine meter
electronic timers on up to 4 softeners can be linked and programmed for optimal treatment over highly variable and high flow rate applications. Systems operators program the flow rates at which each tank enters/leaves service mode. System is interlocked, allowing only one tank to regenerate at a time (immediate regeneration).
Flow rates shown are assuming one tank is off-line for regeneration.
(1, 2, 3, or 4 tanks in operation depending on flow rate and regeneration status)

120v/24v CUl/Ul listed transformer included with electronic meter systems
low flow channeling less than .5 gpm/cu. ft. resin may cause hardness leakage

electronic Requirements
Influent Turbidity
Influent Chlorine
Iron/Manganese
35 110F
35 120F
20 125 psi
110v/60Hz
5 NTU
1 ppm max.
< 5 ppm
- 53 -
Automatic Water Filters

STANDARD FEATURES
COMMERCIAL
High Flow Control Valves thru 3 140 gpm/tank

Up to 24 cu.ft. Media per Tank
Raw Water backwashing Raw Water bypass
Premium Grade and NSF Approved Media
Upflow Filters Available for pH Adjustment No backwashing
electronic Control Valves
OPTIONS
No Raw Water bypass
2750, 2850, or 3150 Top-mount Control Valves
Steel and ASMe rated Pressure Vessels
Flow Management with Motorized ball
Valves or Staged Diaphragm Valves
Water Quality Monitor and Pressure loss
Initiated backwashing
Special Media for Custom Applications
TYPICAL USE
Pretreatment for Other
Processes
Hospitals
Food/beverage Mfg.
Hotels/Motels
Apartments/Condos
laundry Facilities
Food Service
Truck/Car Washes
Automatic backwashing and upflow water filters are the answer for
solving common water quality problems. Only the highest quality,
proven media and controls are used in CSI Automatic Water Filters;
for removal of taste, odor, color, sediment, low pH and iron. Our
motor-driven piston control valve is the most reliable under even
severe water conditions and resists common adversaries such as
dirt, iron and turbidity. Meanwhile, our Vortech or hub and lateral
style distribution system within the corrosion-resistant tanks maximize flow while reducing pressure loss through the units. Designed
for use in commercial, industrial or domestic water applications.
As we remain Committed to Innovation, CSI provides the design
and engineering support to ensure the most effective treatment
solution for each installation. For a stand-alone installation or a
new construction project, replace or integrate new equipment into
an existing process, we have the proper system options available
to meet your needs.
- 54 -
Automatic Water Filter Specifications
11
15
16
19
17
25
39
56
Serv - Peak
CWF30NC-10WS
CWF30NC-12WS
CWF40NC-10WS
CWF40NC-12WS
CWF40NC-15WS
CWF50NC-10WS
CWF50NC-12WS
CWF50NC-15WS
CWF70NC-10WS
CWF70NC-12WS
CWF70NC-15WS
CWF100NC-12WS
CWF100NC-15WS
CWF140NC-15WS
CWF140NC-20WS
CWF180NC-20WS
CWF240NC-20WSH
Serv - Cont.
9
9
11
11
11
15
15
15
17
20
20
24
25
39
39
56
77
10
10
11
11
11
15
15
15
20
20
20
25
25
40
40
60
80
5.5
5.5
7
7
7
9
9
9
12
12
12
16
16
25
25
35
48
9
9
11
11
11
15
15
15
17
20
20
24
25
39
39
56
77
CWF30FP-10WS
CWF30FP-12WS
CWF40FP-10WS
CWF40FP-12WS
CWF40FP-15WS
CWF50FP-10WS
CWF50FP-12WS
CWF50FP-15WS
CWF70FP-15WS
CWF70FP-20WS
CWF100FP-15WS
CWF100FP-20WS
CWF140FP-20WS
CWF180FP-20WSH
CWF180FP-30WS
CWF240FP-30WS
17
17
20
20
20
25
25
25
35
35
45
45
70
105
105
140
11
11
14
14
14
18
18
18
24
24
31
31
49
71
71
96
16
16
17
21
21
18
23
27
36
36
43
47
69
80
106
144
Tank dia x
nom. Ht.
O/A Ht.
14" X 65"
16" x 65"
18" x 65"
21" X 62"
24" X 72"
10
30" X 72"
14
36" X 72"
18
42" X 72"
24
Service Pipe Sizes, Tank Sizes, Cu.ft. , O/A Ht.
GPM
Backwash
Serv - Peak
5.5
5.5
7
7
7
9
9
9
12
12
12
16
16
25
25
35
48
Serv - Peak
CU40N-10
CU50N-10
CU70N-10
CU70N-20
CU100N-10
CU100N-20
CU140N-20
CU180N-20
Cont.
GPM
10
10
15
15
15
20
20
20
25
25
25
30
30
50
50
70
100
- For Acid water

(down to 5.0 pH).
- For Turbidity, dirt,
sediment, etc.
CWF30F-10WS
CWF30F-12WS
CWF40F-10WS
CWF40F-12WS
CWF40F-15WS
CWF50F-10WS
CWF50F-12WS
CWF50F-15WS
CWF70F-10WS
CWF70F-12WS
CWF70F-15WS
CWF100F-12WS
CWF100F-15WS
CWF140F-15WS
CWF140F-20WS
CWF180F-20WS
CWF240F-20WSH
Serv - Cont.
- Acid water
(to 5.8 pH*).
11
11
14
14
14
18
18
18
17
23
24
24
31
38
50
70
87
96
Cu.ft.
Neutralizer UPFLOW
Serv - Cont.
CWF30N-10WS
CWF30N-12WS
CWF40N-10WS
CWF40N-12WS
CWF40N-15WS
CWF50N-10WS
CWF50N-12WS
CWF50N-15WS
CWF70N-10WS
CWF70N-12WS
CWF70N-15WS
CWF100N-12WS
CWF100N-15WS
CWF140N-15WS
CWF140N-20WS
CWF180N-20WS
CWF240N-20WSH
5.5
5.5
7
7
7
9
9
9
12
12
12
16
16
25
25
35
48
48
NEU-COR Auto
Backwash
- For Acid water

(down to 5.8 pH*).
sediment, etc.
10
10
11
11
11
15
15
15
20
20
20
25
25
40
40
60
80
80

sediment, etc.
- Filters solids down
to 5 micron or less.
GPM
Backwash
GPM
CWF30C-10WS
CWF30C-12WS
CWF40C-10WS
CWF40C-12WS
CWF40C-15WS
CWF50C-10WS
CWF50C-12WS
CWF50C-15WS
CWF70C-10WS
CWF70C-12WS
CWF70C-15WS
CWF100C-12WS
CWF100C-15WS
CWF140C-15WS
CWF140C-20WS
CWF180C-20WS
CWF240C-20WSH
CWF240C-30WS

sediment, etc.
- Filters solids down
to 20-40 micron.
Filter-AG Plus Auto

Serv - Peak
7.5
7.5
14
14
14
18
18
18
17
23
24
24
31
47
50
70
87
96
GPM
Serv - Cont.
5.5
5.5
7
7
7
9
9
9
12
12
12
16
16
25
25
35
48
48
De-Chlorin.
Serv - Peak
10
10
15
15
15
20
20
20
25
25
25
30
30
50
50
70
100
100
VOC Treat.
Serv - Cont.
CWF30B-10WS
CWF30B-12WS
CWF40B-10WS
CWF40B-12WS
CWF40B-15WS
CWF50B-10WS
CWF50B-12WS
CWF50B-15WS
CWF70B-10WS
CWF70B-12WS
CWF70B-15WS
CWF100B-12WS
CWF100B-15WS
CWF140B-15WS
CWF140B-20WS
CWF180B-20WS
CWF240B-20WSH
CWF240B-30WS
- For Chlorine, VOC,

Taste, Odor, Color.
sediment, etc.
Filter-AG Auto
Backwash
Backwash
COMMERCIAL
- For up to 5 ppm iron.

- pH must be 6.8 to 9.0.
- Must be 0 sulfur & chlorine.
-See Note at bottom.
Neutralizer Auto
GPM
Carbon Auto
Backwash
GPM
BIRM Auto
10
10
15
15
15
20
20
20
25
25
25
30
30
50
50
70
100
5.5
5.5
7
7
7
9
9
9
12
12
12
16
16
25
25
35
48
9
9
11
11
11
15
15
15
17
20
20
24
25
39
39
56
77
Operating Information & Notes

Always consider BACKWASH req'd; mult units may be needed.
For use on potable water only.
Do not use on microbiologically unsafe or unknown water quality.
Installation must comply with state & local codes.
Warranty void if system subjected to vacuum.
Water Temperature range:
35 - 110F
Ambient Air Temperature range:
35 - 120F
Operating Pressure Range:
20 - 125 psi
Electric Requirements (for CWF series):
115v/60Hz
BIRM requires dissolved oxygen at least 15% of iron.
* If more than 7 gpg hard, then Neutralizer okay for down to 5.8pH.
If less than 7 gpg hard, then Neutralizer okay for down to 6.5pH.
Series
CWF30_-10WS
CWF30_-12WS
CWF40_-10WS
CWF40_-12WS
CWF40_-15WS
CU40-10, CU40N-10
CWF50_-10WS
CWF50_-12WS
CWF50_-15WS
CU50-10, CU50N-10
CWF70_-10WS
CWF70_-12WS
CWF70_-15WS
CWF70_-20WS
CU70-10, CU70N-10
CU70-20, CU70N-20
CWF100_-12WS
CWF100_-15WS
CWF100_-20WS
CU100-10, CU100N-10
CU100-20, CU100N-20
CWF140_-15WS
CWF140_-20WS
CU140-20, CU140N-20
CWF180_-20WS
CWF180_-20WSH
CU180-20, CU180N-20
CWF240_-20WSH
CWF240_-30WS
Service Size
1" NPT
1.25" NPT
1" NPT
1.25" NPT
1.5" NPT
1" NPT
1" NPT
1.25" NPT
1.5" NPT
1" NPT
1" NPT
1.25" NPT
1.5" NPT
2" NPT
1" NPT
2" Socket
1.25" NPT
1.5" NPT
2" NPT
1" NPT
2" Socket
1.5" NPT
2" NPT
2" Socket
2" NPT
2" NPT
2" Socket
2" NPT
3" NPT
- 55 -
73"
73"
73"
73"
73"
68"
76"
76"
75"
72"
75"
75"
75"
76"
68"
73"
83"
82"
83"
77"
89"
85"
86"
91"
98"
100"
92"
101"
102"
REACTR Treatment Systems

STANDARD FEATURES
COMMERCIAL
Catalog Systems to 200 gpm

Aeration via Ambient Air NO CHeMICAlS
Aeration Manifold Assembly Machined from
Solid PVC barstock
Automatic Self-Regulating Air Volume Control
Smart-blend Filter Media*
No Raw Water bypass - While One Tank is
backwashing, The Other Tank(s) is(are) Still In-service.
OPTIONS
*Smart-Blend is the media used on the listed standard

models. It is a proportioned mix of three proven
filter medias that provide a spectrum of filtering capabilities
for a wide range of water problems.
TYPICAL USE
large Scale Irrigation
Public Water Systems
Dairy Operations
Hotels/Motels
Apartments/Condos
laundry Facilities
Food/beverage Mfg.
livestock Operations
Schools
Hospitals
Clean blended Water backwash, for Systems

Installed Ahead of Atmospheric Storage Tanks.
Multiple Aeration Tank Sizes
Chemical Injection Ports on Aeration Manifold
Air Compressor Injection for Variable Speed Well
Pump Systems
Flow Management with Motorized ball Valves or
Diaphragm Valves
Custom Designed Systems
Various Filter Medias as alternate to Smart-blend
Our ReACTR Treatment System incorporates aeration technology that efficiently mixes ambient air with water under pressure to convert iron, manganese and hydrogen sulfide gas to
filterable particles. The ReACTR eliminates the associated
stains, taste and odor while eliminating sediment problems
and neutralizing low pH on influent water. Only the highest
quality controls and materials are used. Our motor-driven piston control valve is the most reliable under even severe water
conditions and resists common adversaries such as dirt, iron
and turbidity. Designed for use in commercial, industrial or
domestic water applications.
treatment solution for each installation. For a stand-alone
installation or a new construction project, replace or integrate
new equipment into an existing process, we have the proper
system options available to meet your needs.
- 56 -
REACTR Treatment System Specifications

MODEL NUMBERS
COMMERCIAL
PRESSURE
SYSTEMS
Service GPM
VARIABLE SPEED
SYSTEMS
Backwash
Pipe Size NPT

Ctrl Valve Drain
Conn Size Line
Continuous
Flow Rate
Peak
Flow Rate
Flow
GPM
Filter Tank
Cu.Ft. Media
Tank
Size
Tank
Qty
Per
System
CRF25-102-WS
CRF25-102VS-WS
14
1"
3/4"
13"x 54"
CRF40-102-WS
CRF50-102-WS
CRF70-102-WS
CRF40-102VS-WS
CRF50-102VS-WS
CRF70-102VS-WS
14
18
24
20
22
13
17
25
1"
1"
1"
1"
1"
1"
16"x 65"
18"x 65"
21"x 62"
2
2
2
8
10
14
CRF50-103-WS
CRF70-103-WS
CRF100-123-WS
CRF140-152-WS
CRF100-124-WS
CRF50-103VS-WS
CRF70-103VS-WS
CRF100-123VS-WS
CRF140-152VS-WS
CRF100-124VS-WS
27
36
45
50
60
30
17
25
30
50
30
1"
1"
1 1/4"
1 1/2"
1 1/4"
1"
1"
1 1/4"
1 1/2"
1 1/4"
18"x 65"
21"x 62"
24"x 72"
30"x 72"
24"x 72"
3
3
3
2
4
15
21
30
28
40
CRF180-202-WS
CRF180-202VS-WS
70
70
2"
2"
36"x 72"
36
CRF140-153-WS
CRF140-153VS-WS
75
50
1 1/2"
1 1/2"
30"x 72"
42
CRF240-202-WSH CRF240-202VS-WSH
CRF140-154-WS
CRF140-154VS-WS
100
100
95
50
2"
1 1/2"
2"
1 1/2"
42"x 72"
30"x 72"
2
4
48
56
CRF180-203-WS
CRF180-203VS-WS
CRF140-155-WS
CRF140-155VS-WS
CRF180-204-WS
CRF180-204VS-WS
105
125
140
150
70
50
70
95
2"
1 1/2"
2"
2"
2"
1 1/2"
2"
2"
36"x 72"
30"x 72"
36"x 72"
42"x 72"
3
5
4
3
54
70
72
72
CRF180-205-WS
CRF180-205VS-WS
175
200
70
95
2"
2"
2"
2"
36"x 72"
42"x 72"
5
4
90
96
Manganese Removal
If the Iron to
Manganese ratio is:
Then the pH must

be at least:
10:1
7.0
5:1
7.8
1:1
8.3

For effective
Iron and Sulfur
removal, your
ppm's must be
on or below
these curves
Additional equipment is required for water

containing organic and/or bacteria versions
For Pressure System models, at rated
GPM, the inlet PSI at the Reactr Tank must
be at least 25 PSI higher than max PSI at
service. If supply pump cannot achieve this
pressure, then use Variable Speed Systems
If needed, pH can be increased by
injecting soda ash or caustic into the Reactr
Tank Manifold
Periodic replenishing of the Neutralizer in the
filter tanks will be required for water less than
7.0 pH (normally 6 to 12 months, depending
on influent pH)
- 57 -
HydroxR Treatment Systems

STANDARD FEATURES
large Scale Irrigation

Public Water Systems
Dairy Operations
Hotels/Motels
Apartments/Condos
laundry Facilities
Food/beverage Mfg.
livestock Operations
Schools
Hospitals
COMMERCIAL
TYPICAL USE
Combines Aggressive Pressurized Aeration with the Oxidation

Power of Hydrogen Peroxide (H2O2)
Treats extreme levels of Iron, Manganese & Sulfur
Disinfection Properties to Treat Iron, Manganese & Sulfur
bacteria
Catalog Systems to 105 gpm
Catalog Models for Pressure Systems (traditional 3450 rpm
Submersible Pumps)
-or- Clean Water backwash Systems (Installed Ahead of
Atmospheric Tank)
-or- Pressure Variable Speed System (Constant Pressure, Jet
Pumps or Other low Inlet Pressure Applications)
Aeration Manifold Assembly Machined from Solid PVC barstock
Automatic Self-Regulating Air Volume Control
Filter-Ag Plus Filter Media
No Raw Water bypass
Chemical Feed Pump & Solution Tank
electronic Control Valves
Includes 5-Gal Hydrogen Peroxide
OPTIONS
Multiple Aeration Tank Sizes
extra Chemical Injection Ports on Aeration Manifold
Flow Management with Motorized ball Valves or Staged
Diaphragm Valves
Custom Designed Systems, for Higher Flow Rates
Various Filter Medias
Our hydroxR Treatment System combines aggressive aeration technology with the oxidation power of
hydrogen peroxide for treatment of virtually unlimited levels of iron, manganese and sulfur gas.
At the same time, bacteriological forms of these constituents are controlled without the creation of chemical byproducts, contact tanks or the on going maintenence of rebedding carbon filters. The included chemical feed pump package is equipped with a Degas head for self-priming operation. Only the highest quality
controls and materials are used. Our motor-driven piston control valve is the most reliable under even
severe water conditions and resists common adversaries such as dirt, iron and turbidity. Designed for use
in commercial, industrial or domestic water applications.
As we remain Committed to Innovation, CSI provides the design and engineering support to ensure the
most effective treatment solution for each installation. For a stand-alone installation or a new construction
project, replace or integrate new equipment into an existing process, we have the proper system options
available to meet your needs.
- 58 -
HydroxR Treatment System Specifications

MODEL NUMBERS
COMMERCIAL
PRESSURE
SYSTEMS
VARIABLE SPEED
SYSTEMS
Service GPM
Backwash
Pipe Size NPT
Continuous
Peak
Flow Rate Flow Rate
Flow
GPM
Ctrl Valve Drain

Conn Size Line
CUTP25-102-WS
CUTP40-102-WS
CUTP25-102VS-WS
CUTP40-102VS-WS
9
14
14
20
13.5-15
20
CUTP50-102-WS
CUTP40-103-WS
CUTP50-103-WS
CUTP70-153-WS
CUTP100-153-WS
CUTP50-102VS-WS
CUTP40-103VS-WS
CUTP50-103VS-WS
CUTP70-153VS-WS
CUTP100-153VS-WS
18
21
27
36
45
22
24
30
25
20
25
35
45
CUTP100-154-WS
CUTP140-203-WS
CUTP140-204-WS
CUTP100-154VS-WS
CUTP140-203VS-WS
CUTP140-204VS-WS
60
75
100
45
70
70
105
105
CUTP180-203-WSH CUTP180-203VS-WSH
Manganese Removal
HydroxR capability to remove Manganese
from water is critically dependent on the Iron and
pH levels as shown below:
If the Iron to
Manganese ratio is:
Then the pH must

be at least:
5:1
1:1
0:1
7.0
7.8
8.3
1"
1"
1"
1"
1"
1"
1"
1"
1"
1"
1 1/2" 1 1/4"
1 1/2" 1 1/4"
1 1/2" 1 1/4"
2"
2"
2"
2"
2"
2"
Filter Tank
Cu.Ft. Media
Tank
Size
Tank
Qty
Per
System
13"x 54"
16"x 65"
2
2
5
8
18"x 65"
16"x 65"
18"x 65"
21"x 62"
2
3
3
3
10
12
15
21
24"x 72"
24"x 72"
30"x 72"
30"x 72"
3
4
3
4
30
40
42
56
36"x 72"
54
For Pressure System models, at rated GPM, the inlet PSI

at the HydroxR Tank must be at least 25 PSI higher than
max PSI at service. If supply pump cannot achieve this
pressure, then use Variable Speed Systems
If needed, pH can be increased by injecting soda ash or
caustic into the HydroxR Tank Manifold

100
80
N
IRO
UR
ppm
lF
SU
60
40
20
0
6.5
7.5 8
ph
8.3 8.5


Electronic Requirements
35 110F
35 110F
20 125 psi
110v/60Hz
- 59 -
Reverse Osmosis Systems

STANDARD FEATURES
COMMERCIAL
Pre-Packaged Assembled PlugnPlay Install

Powder-Coated/epoxy Steel Frame
Small Footprint per Daily Gallon Capacity
304/316* Stainless Steel Multi-Stage Pump
PVC Pressure Vessels
High Rejection TFC Cold Water Membranes
5 Micron Sediment Pre-Filter
low Pressure Switch
Permeate/Concentrate Pressure Gauge & Control Valve
Package with Flow Meters
Concentrate Recycle Valve & Flow Meter
low Pressure with Inlet Solenoid
* - 316 thru 8K gpd; 304 at 10K gpd & larger
OPTIONS
Digital TDS Monitor/Controller
RP or Stainless Steel Pressure Vessels
Pump Discharge Pressure Gauge
Automatic Fast Flush
Atmospheric Storage Tank with Floats
Pressurized Storage (3 tank sizes)
Atmospheric Storage with Dispenser
brackish Water/Sea Water Applications
System thru 400 gpm
TYPICAL USE
Restaurants
Hospitals/labs
Industrial Processes
Manufacturing
Whole House
livestock
laundry Facilities
Car Washes
Convenience Stores
The Reverse Osmosis (RO) process uses a semi-permeable

membrane to separate and remove Total Dissolved Solids (TDS),
organics and submicron colloidal matter from the water. A high
pressure RO pump is used to force raw water through the multilayered membrane, leaving the impurities behind (concentrate)
while creating pure water (permeate). Pre-treating the raw water
with filtration and/or softening before the RO is commonly
required. Reverse Osmosis is capable of removing 95 99% of
the TDS from raw water.
treatment solution for each installation. For a stand-alone installation on a new construction project, replacing existing equipment
or integrating new equipment into an existing process, we have
the proper system and equipment options available to meet your
need.
- 60 -
COMMERCIAL
Reverse Osmosis System Specifications
Model Numbers
Standard
N/A
Deluxe
GPD Production - 1000

TDS/F
77F
60F
45F
Inlet
FPT
Outlet
FPT
Motor
Dimension
s
Membrane
HP
Volt*
Size
Qty
HxWxL inches
LP-500
525
410
326
3/4"
3/8"
1/4
115
2.5"X21"
46"X20"X13"
EPRO-600
EPRO-600DX
600
468
372
1/2"
1/2"
1/3
115
2.5"X40"
53"X17"X20"
EPRO-1200
EPRO-1200DX
1,200
936
744
1/2"
1/2"
1/2
115
2.5"X40"
53"X17"X24"
EPRO-1500
EPRO-1500DX
1,500
1,170
930
3/4"
1/2"
230
4"X40"
53"X20"X26"
EPRO-3000
EPRO-3000DX
3,000
2,340
1,860
3/4"
1/2"
230
4"X40"
53"X20"X26"
EPRO-4500
EPRO-4500DX
4,500
3,510
2,790
3/4"
1/2"
1.5
230
4"X40"
53"X20"X26"
EPRO-6000
EPRO-6000DX
6,000
4,680
3,720
3/4"
3/4"
230
4"X40"
53"X20"X26"
EPRO-8000
EPRO-8000DX
8,000
6,240
4,960
3/4"
3/4"
230
4"X40"
53"X20"X26"
EPRO-10000
N/A
EPRO-10000DX
10,000
7,800
6,200
1.5"
1"
230
4"X40"
48"X64"X26
EPRO-11500DX
11,500
8,970
7,130
1.5"
1"
230
4"X40"
48"X64"X37"
N/A
EPRO-13000DX
13,000
10,140
8,060
1.5"
1"
230
4"X40"
48"X64"X37"
N/A
EPRO-14500DX
14,500
11,310
8,990
1.5"
1"
230
4"X40"
48"X64"X37"
N/A
EPRO-16000DX
16,000
12,480
9,920
1.5"
1"
230
4"X40"
10
48"X64"X37"
N/A
EPRO-17500DX
17,500
13,650
10,850
1.5"
1"
230
4"X40"
11
48"X64"X37"
N/A
EPRO-19000DX
19,000
14,820
11,780
1.5"
1"
7.5
230
4"X40"
12
48"X64"X37"
N/A
EPRO-20500DX
20,500
15,990
12,710
1.5"
1"
7.5
230
4"X40"
13
48"X64"X37"
N/A
EPRO-21500DX
21,500
16,770
13,330
1.5"
1"
7.5
230
4"X40"
14
48"X64"X37"
* - volt and phase options available
MODEL SELECTION CRITERIA
1. Type of raw water Tap/Well Water (up to 2,000 TDS), brackish Water (up to
10,000), Sea Water
2. Quality of Product Water Required High Purity, Potable, Process (define target
TDS/conductivity)
3. Volume of Product Water Required gallons per day or gallons per minute
4. Installation environment atmospheric storage, re-pressurization, pressurized
storage, custom
DESIgN ADVANTAgES
1.
2.
3.
4.
5.
6.
SYSTEM OPERATION PARAMETERS
Complete water analysis required for model and option selection

System rated capacity above based on feed water with 1,000 TDS and temperature of
77F
Inlet feed water pressure a minimum of 50 psi at 120% treated water flow rate demand
110-220VAC/ 60Hz /1Ph electrics up to 6,000 gpd; 230-460VAC/60Hz/3Ph for 10,000
gpd and larger
Non-detectable levels of oxidizing disinfectants (chlorine, etc.) and hydrogen sulfide
ensure sufficient space available for removing/replacing membranes; refilling chemical
solution tanks
7.
8.
Single Power Point for RO Machines

Skid envelope Protects Major Components
Simple-to-operate Controls for all System
Functions
easy Startup, Commissioning & Maintenance
Configured by Our Application engineers to
Meet Your Specific Requirements (You Dont
buy What You Dont Need)
Components Integrated into a Simple to Install
and Operate Unit
Solid Hydraulic Design Protects Your
Investment
All RO Units are Tested Prior to Shipment
- 61 -
TECHNICAL
Technical
Section
- 62 -
REACTR Technical Information Guide
I.
General Information
The REACTR Water Treatment System is a revolutionary product that has the capability of removing Iron, Manganese,
Turbidity, Sulfur and other Gases, improving taste, odor and color while also adjusting upwardly the pH of acid water. It
does all of these things, under proper conditions, without the use of chemicals and/or regenerants like salt, chlorine and
potassium permanganate.
The only maintenance required for most installations is an occasional backwashing which is done automatically. Most systems will require backwashing only once or twice in a six day period as you will see in the chart shown later in this technical
information guide.
The key to a successful installation is, of course, having the proper water testing, water pumping system, equipment selection
and installation. We hope to provide you with as much of this information as possible throughout the next few pages. let's
first see how the REACTR accomplishes its task of providing naturally treated water.
II.
REACTR : How Does It Work?

Please look over Typical Installation Figure 1 on the next page before we begin studying the various functions of the system.
TECHNICAL
As we discuss the functions, we will move from the left to right on the diagram. Please refer to the circled letters within the
figure of each component part or portion of the system we are discussing as shown alphabetically below.
A. Pump - Since the REACTR requires both sufficient flow and pressure to operate, you should generally limit installations to only those jobs where you have a submersible pump that has been properly sized for the well. There are only a
few exceptions to this general rule that we will discuss later, but for most all cases, limit your installations to submersible
pumps. Generally, jet pumps do not provide both flow and pressure in combination to let the REACTR Manifold {e}
work properly. If you do have a job that is to be treated where a jet pump is involved, either include a new submersible
with the installation or contact your distributor or the CSI factory for acceptable non-submersible applications.
NOTE : REACTR cannot be used with constant pressure pump systems!! (Consult factory for details).
b. Check Valve - It is recommended that a check valve be installed above ground as a back-up to the well check. In the
event the primary check valve fails, the above ground check will prevent a back flow of water down the well. This could
cause a negative pressure situation which can collapse the REACTR tanks. This cannot be covered under the standard warranty if this occurs.
C. Pressure Relief Valve - This is an optional piece of equipment that should be installed between the pump and the
REACTR tank. The relief valve will protect the system from an over pressure situation. A relief valve with a minimum
125 psi blow off should be used.
D. Pressure gauge - It is highly recommended that a gauge be installed at this location for the purpose of reading actual
head pressure being delivered from the pump during the pump cycle. A gauge at this location will be invaluable if later
troubleshooting of the system is required.
- 63 -
FIgURE 1
TECHNICAL
- 64 -

e.
REACTR Tank Manifold - The REACTR Tank Manifold is a special device designed and manufactured by CSI that
brings air into the water system. This is where actual "treatment" of the water begins. This air starts the oxidation
process of producing physical particles that will be trapped by the filter portion of the system. The relatively high pressure and flow delivered by the pump, compared with the lower system pressure (i.e. 30/50 psi switch setting), causes a
point of low pressure and suction in the center of the REACTR Tank Manifold. This suction is what draws air into the
system through the air intake valve check located on the side of the REACTR manifold.
TECHNICAL
FIgURE 2
The water flowing into the REACTR Tank Manifold is somewhat restricted in the nozzle section. When the nozzle receives sufficient pressure, suction is then created at the point the water leaves the nozzle and enters the
opening of the venturi section. This is where the air is pulled into the water flow. If there is more than the required
amount of water flow entering the nozzle (5 gpm), a certain amount will go around the nozzle through the bypass
ports. This prevents an unnecessary loss of flow and pressure while the pump is operating. This occurs automatically and does not require adjustments. The bypass water then rejoins the main stream of flow at the end of the
venturi, where it mixes with the water flow that received the air injection. This mixing point assures that all of the
water comes into contact with the air. (See Figure 2.)
- 65 -

The amount of differential pressure generally required to operate the REACTR manifold is 20 psi. Consider this number as
a constant in all residential systems. You can actually determine the air draw into the system by following this example :
how To Calculate Air Draw

Simply determine the Head Pressure (Gauge {D}) offered by the pump and subtract the constant of 20# differential required
to operate the REACTR manifold. The answer you get will tell you the point at which the REACTR manifold will stop
drawing air. This pressure number is the pressure seen on gauge {J} - system pressure. If Head Pressure (gauge {D}) is 65
psi on a 30/50 system ...
65 psi (Gauge {D})
- 20 psi (Differential Constant)
45 psi (Will draw air to this system pressure)
In this case, air will be drawn by the REACTR manifold from 30 psi to 45 psi (on gauge {J}) or 75% of the pump cycle.
As a general rule, we want to have at least a 25% air draw at the REACTR manifold. The higher level of contamination in
the water, the more air draw we need. You will find that most properly sized submersibles will easily give you from 50% to
100% air draw.
FIgURE 3
TECHNICAL
- 66 -

ee. REACTR Tank - This tank is critical to the operation of the REACTR System. All water and excess air that is taken
into the water system by the REACTR manifold passes through this tank on its way to the pressure tank and then the
REACTR Filter. There are certain dynamics that occur in this tank which move contaminants closer to a fully oxidized
state. let's discuss just how the REACTR tank works.
TECHNICAL
As we continue with the REACTR tank, please refer to Figure 3. As water flows from the well pump and enters the
REACTR tank manifold {e}, the nozzle/venturi section {A} creates a suction and draws air into the water through the air
intake valve check {b}. The valve check body is constructed of Isoplast and is totally serviceable. The inner valve check
assembly is sealed on either side by Viton O-rings located in the cap and body utilizing a Hastelloy spring, and seals with a
small Viton O-ring. To access the inner valve check, push in forcefully on the cap and turn 1/4 turn to the left. A minimum
flow of 5 gpm is required to satisfy the nozzle/venturi section of the REACTR manifold. Once the center nozzle/venturi
section is satisfied with flow, any flow over 5 gpm will be automatically bypassed through the three bypass holes located
around the outer perimeter of the nozzle/venturi section. This bypass flow will rejoin the aerated water on the outlet side of
the REACTR tank manifold. The combined air / water mixture then forcefully contacts the REACTR diffuser {C} where
the high level of free air separates and remains in the top section of the REACTR tank. Water and contaminants move
downwardly to the bottom of the tank {D} and exit towards the filter. After a short time, there will be a full head of air in
essence Aerating the water as it sprays out away from the diffuser. This aeration process is very effective because air is
forced into the water due to the fact that the REACTR tank is under full line pressure. This is superior to atmospheric
aeration due to the speed and efficiency that contaminants (e.g. iron and sulfur) are oxidized.
As more and more excess air is trapped in the top section {e} of the REACTR tank, the water level moves lower in
the tank. This is what we call the maturity level in the REACTR tank. When additional air is introduced into the
REACTR tank thereafter, the water level falls and the weighted float inside the float guide {F} drops momentarily
allowing a proportionate amount of air to escape from the REACTR tank manifold through the exhaust vent {G} and
out the air vent line {H} to a drain. When sufficient air has vented to allow the water level to rise back to the maturity
point, the water rising allows the float to become buoyant once again. The float then closes off the exhaust vent so that
air is kept in the REACTR tank.
It is an important safety measure to run the exhaust vent line to a drain. Normally, there will be a very small amount of
water discharged with the air as the system vents. However, in the event that the float malfunctions and stays "open",
water will continuously run through this line until the float returns to shut-off or a repair is made. Always run this vent
line to a drain to prevent flooding should a problem arise. The exhaust vent line can be run outside as long as measures are taken to prevent the line from freezing shut during cold weather. It is important to mention that if the REACTR is being used to treat hydrogen sulfide gas (H2S), the air will oxidize most of the gas to a particle of elemental
sulfur. Consequently, very little smell, if any, will be experienced out of the air vent line.
To this point, the contaminants in the raw water have been forced through the nozzle/venturi section of the REACTR
tank manifold where they are exposed to compression/decompression, a massive quantity of air, and forcefully at full
pump flow diffused through the head of air in the top of the REACTR tank. by this time, significant oxidation has
occurred. but there is yet another function to be performed by the REACTR tank. Notice the plastic air stripping
balls {I} located in the REACTR tank. These balls do not perform filtration, but serve to accomplish two other functions. Precipitated contaminants (e.g. ferric and manganic hydroxides) will form a thin coating on the surface of the air
stripping balls. As the water / contaminant mixture moves over the balls on it's way to the bottom outlet of the REACTR tank, the coating of oxidized contaminants on the balls chemically assists yet unoxidized contaminants to move
closer to a fully oxidized state by a chemical process called sorbing.
The second function of the air stripping balls is to further mix the dissolved oxygen with the water and to help hasten
the oxidation of certain gases (e.g. hydrogen sulfide). Due to the large openings in these balls, the water is sheared
as it passes through them, and allows for a thorough mixing of oxygen, water and the separation of excess gases. As
we continue our discussion, please refer back to Figure1.
- 67 -

F.
Pressure Tank - All REACTR Systems will require a pressure tank, unless installed ahead of an atmospheric storage tank. In the case of an atmospheric storage tank, the system will need to be configured for clean water backwash
or a change in pump wiring will need to be done to provide pump flow for backwashing purposes. (Contact the factory
or your sales representative for details.) Due to the fact that all the excess free air is being exhausted prior to the
pressure tank, either a precharged diaphragm / bladder type or air-to-water lined galvanized tank may be used.
G. Split System - If a secondary service line (split system) is to be installed ahead of the REACTR tank to provide
untreated water (e.g. irrigation, outside faucets, etc.), it is highly recommended that a bypass line be installed between
the REACTR tank and the pressure tank. This will allow draw down from the pressure tank to bypass the
REACTR tank until the pressure switch closes and turns the pump on providing true raw water to the secondary
service line.
Note : In most irrigation applications, the well pump will be oversized to provide adequate flow for both the irrigation
system and the home. In these cases, a REACTR Manifold with a larger venturi/nozzle size will probably be
required. (e.g. 10 gpm or 15 gpm). This will prevent high head pressure from developing when the irrigation system is
not in use.
H.
Check Valve - A one way check valve should be installed at the two locations shown. This will prevent free air from
escaping the REACTR tank into the secondary service line and also provide one way passage of flow from the
pressure tank when secondary service is operated.
I.
Pressure Switch - This is any good quality pressure switch usually preset to the 30 / 50 psi range. Remember that
the point at which the pressure switch senses pressure must always be located after the REACTR tank so that it
reads SYSTEM and not pump head pressure.
J.
Pressure Gauge - This is the gauge that shows current system pressure. It is the difference between this gauge and
gauge {D} that will show you differential pressure for any given water system.
K.
REACTR Filter Tank - The filter tank serves several important functions. Its primary purpose is to trap the physical
particles (e.g. ferric hydroxides and elemental sulfur) that have been produced by the oxidation process. We have
simply taken unfilterable dissolved solids and converted them by an oxidation process to precipitated and filterable
suspended solids. In most cases, the particles are trapped on the surface and in the top portion of the mineral
bed {l}.
l.
The mineral bed of the REACTR consists of a proportioned mixture of three (3) proven filter medias known as
Smart Blend . The three media are:
TECHNICAL
Note : If it is ever desired to change the pressure switch setting (cut on / cut off), always drain the system and
change the precharge in the pressure tank to 2 psi below the cut on pressure (e.g. 40 /60 setting - precharge = 38
psi). This is extremely important as maximum draw down, pump run time and contact time will be achieved.
Filter Ag
Neutralizer
Manganese Dioxide
This media is coarsely blended by CSI and serves the following functions. The entire bed provides excellent
mechanical filtration due to the angular / granular nature of the individual minerals.
Filter Ag - Specifically, Filter Ag is non-hydrous aluminum silicate. It's only function is that of mechanical filtration.
Neutralizer - Neutralizer is a carefully graded white marble (calcium carbonate). It's primary function is to elevate the
pH level of the filtered water by a slow, dissolving process. If the pH is below 7.0 (acidic), it will be raised to 6.8 - 7.2
pH depending on the raw water pH and the flow rate (contact time) through the system. If this is the case, then
periodic replenishing of the neutralizer will be required.
- 68 -

Manganese Dioxide - This media is an active, insoluble catalyst that utilizes dissolved oxygen in water to convert clear
iron, sulfur gas & manganese to a filterable state. It serves as an "insurance policy" in the filter bed during peak demand
periods to remove traces of iron / manganese & sulfur in the event that they were not fully oxidized prior to entry into the
filter bed.
M.
Vortech Distributor Plate - beneath the Smart Blend filter media {l} is the Vortech Distributor plate. The purpose
of the Vortech is to permit even flow of the water during both service and backwash modes. Also, the Vortech provides
a vigorous backwash helping to clean the filter media bed. No gravel underbedding required!
N.
Filter Control Valve - The Filter Control Valve is used for the automatic cleaning (backwashing) of trapped oxidized
contaminants from the filter. The control valve does this by directing the flow of water backwards through the filter, thus
purging the contaminants from the tank and also reorienting the filter bed. This backwash water is then directed out of the
control valve drain line {O}. After the backwash cycle is complete, the control valve will then direct the flow downwards
through the filter tank (rapid rinse), recompacting the mineral bed and flushing any "dirty" water from the bottom section of
the filter. During the backwash cycle, water is available to the house but will be untreated. That is why the REACTR
control valve is factory preset to activate the backwash cycle at 12:00 a.m. on a night it is scheduled. backwash frequency
can be estimated using the formula below:
TECHNICAL
Combined iron and manganese removal for

REACTR Filter = 15,000 ppm per cu. ft. of filter media
example :
Model - RF15
Qty. of Media - 1.5 cu. ft.
Iron / Manganese Content - 5 ppm
Number of People in Family - 4
estimated Water Usage - 75 gals. per person per day
Total iron / manganese removal before backwashing is required :
1.5 cu. ft. x 15,000 ppm / cu. ft. = 22,500 ppm
estimated water usage :
4 people x 75 gpd = 300 gals. per day
Iron / manganese removal per day :
300 gpd x 5 ppm = 1,500 ppm / day
Required backwash frequency :
22,500 / 1,500 ppm / day = 15 days
- 69 -

The required backwash frequency in this example is every 15 days. We want to backwash a minimum of every 6 days to
assure orientation of the filter bed. Program the Signature Series control valve for every 6 days in this example.
Note : For sulfur gas removal, frequency of backwash should be accomplished twice as often as for iron / manganese.
Also, if tannins and / or bacteria versions of these contaminants are involved, the OXYCLEAN Option should be added
to the system and backwash frequency increased to every 3 - 4 days.
The Signature Series Control is provided as the standard valve for the REACTR System. It provides excellent backwash
flow characteristics required for proper cleaning of the filter. It also features adjustable cycle length times (backwash and
rapid rinse) for versatility when well capacities may be at a minimum. Also, the Signature Series control will motor to each
position to provide full flow for the entire cycle duration. This provides for a better backwash and will help keep oxidized
contaminants from collecting inside the valve by keeping water velocities high. For more information about operation and
service of the Signature Series control valve, please consult the Signature Series Service Manual.
O.
Drain Line - During any backwash cycle, water will automatically be directed through the REACTR filter and out the
drain line. A 1/2" I.D. by 5/8" O.D. clear drain line attached to the drain line hose barb is normally used. DO NOT use flimsy
tubing that will kink, reducing drain line flow. Only semi-rigid drain tubing should be used. by removing the drain line hose
barb, a 1/2" drain line can also be hard plumbed in PVC or copper. The drain line should be kept as short as possible and
the diameter of the line should never be decreased to less than that of the hose barb provided with the filter. Decreasing
the diameter will result in a back pressure situation due to friction loss and can result in insufficient backwashing. A 4" air
gap should also be maintained to prevent a possible syphoning of water standing in the drain back into the filter.
TECHNICAL
FIgURE 4
- 70 -

III.
The OXYCLEAN Option - Please refer to Figure 4 before we begin studying the function of the OXYCLEAN.
The OXYCLEAN is an optional piece of equipment that can be added to any new or previously installed REACTR
System. OXYCLEAN is designed to introduce chlorine automatically during the backwash cycle for cleaning and
disinfecting of the entire system.
In cases of iron bacteria or tannins that can cause fouling of the filter media or heavy iron (over 5 ppm) that can cause pipe
plugging problems, the OXYCLEAN Option can drastically reduce service calls associated with these situations.
The OXYCLEAN Option includes the following items :
OXYCLEAN Feed Pump - The OXYCLEAN Feed Pump is designed to deliver chlorine into the system
during the backwash cycle. It is of a peristaltic design, so ball type check valves that usually require maintenance
are not required. The head tubing is made of heavy duty Norprene for long life. Pump RPM and tubing size is
factory designed to deliver eight (8) ounces of solution in a typical ten (10) minute backwash cycle. Consequently,
there are no settings or adjustments required for the pump during or after installation. because of the peristaltic
design, the pump is totally self priming and will only require a short run time to fill the outlet tubing on initial
installation. The pump is designed to set on the floor adjacent to the solution tank. This will provide flooded
suction to the pump, although the pump may be elevated, if need be. The OXYCLEAN pump is designed for
120 V / 60 Hz power and is plugged into the front of the OXYCLEAN relay panel. NOTE : It is recommended
that the Oxyclean Pump Tubing be replaced every 1 - 2 years. One (1) extra pump tube is included.
b.
OXYCLEAN Solution Tank - The OXYCLEAN Solution Tank is designed to store chlorine for the OXYCLEAN pump. It has a five (5) gallon capacity and includes a tube lock type bulkhead fitting where the OXYCLEAN pump inlet tubing (lower fitting) is to be connected. Fill the OXYCLEAN Solution Tank with straight
6.0% laundry bleach. Do not dilute with water. Chlorine bleach can lose it's strength over a period of time, so it is
suggested to fill the solution tank with two to three gallons of bleach as this will last approximately six to eight
months, depending on the frequency of backwash. A gravity overflow elbow is installed and 1/2 I.D. x 5/8 O.D. tubing should be attached and run to a drain.
C.
OXYCLEAN Injection Check Valve - A 1/4" MNPT plastic pipe plug is threaded into the manifold base on every
REACTR system shipped. Depressurize the system, remove the pipe plug and carefully thread the OXY
CLEAN Injection Check Valve (included with the installation kit) into the 1/4" port. Tighten the check valve by
HAND ONLY! The outlet tubing (upper fitting) from the pump should then be connected to the injection check
valve.
D.
OXYCLEAN Relay Control Panel - A relay control panel is included to provide 120V power to the OXYCLEAN
pump when signaled by the Signature Series Control Valve during backwash. The relay panel should be wall
mounted in close proximity to the REACTR system. The 120V power cord from the relay panel should be
plugged into a 120V wall receptacle with the patch cord connected to the pigtail cord located on the right side of
the Signature Series Control Valve.
e.
Signature Series Control Valve - every REACTR System shipped is equipped with a pigtail cord located on the
right side of the REACTR Signature Series Control Valve. The control valve is designed with an internal contact
that will close providing power to the relay panel only during the backwash cycle. To complete the OXYCLEAN
installation, simply insert the patchcord from the OXYCLEAN relay panel into the pigtail and plug the
OXYCLEAN feed pump power cord into the receptacle located on the front of the relay panel. Then plug the
relay panel power cord into a 120V wall receptacle. backwashing frequency should be set to every 3 - 4 days.
TECHNICAL
A.
- 71 -

The cycle times on all REACTR Signature Series Control Valves will need to be changed to the following:
Oxyclean Cycle Time Settings
backwash
10 minutes
Rest Period
20 minutes
Rapid Rinse
16 minutes
Total
46 minutes
by setting the first rest period to 20 minutes in length, we are able to achieve the contact time needed for chlorine
disinfection. Setting the rapid rinse cycle to 16 minutes will assure that all chlorine residual is flushed from the
system.
IV.
Contaminants In Water
It is critical that the water to be treated with any water treatment equipment be analyzed so that a proper selection of
equipment can be made. Although REACTR handles a wide variety of contaminants, there are certain things to keep in
mind to insure a successful installation. The following is a discussion of various contaminants as they relate to REACTR.
A.
Iron - Concentrations of iron as low as .30 ppm can cause staining of fixtures and laundry. REACTR can
remove various types of iron up to a maximum raw water content of 20 ppm under suitable conditions.
(See Figure 6.) Iron occurs in water in two basic forms;
1. Dissolved Solids - clear or ferrous iron
2. Suspended Solids - red or ferric iron
b.
Iron Bacteria - bacterial forms of iron are non-pathogenic organisms that thrive off of the energy created by the
oxidation of iron and manganese. Since the REACTR oxidizes ferrous iron (clear) to ferric iron (red), iron
bacteria in the water supply can adversely affect the operation of the system. In light to moderate amounts, the
REACTR can usually be successful in treating iron and associated iron bacteria, if the OXYCLEAN Option is
included with the system. When chlorine bleach is used, the OXYCLEAN will inject solution during the back
wash cycle only. This will allow for chemical free treatment of the potable water while adding chemistry during
backwash to keep the REACTR System clean and disinfected. Where heavy amounts of iron bacteria are
encountered, a hydroxR system will probably be recommended. If iron bacteria is suspected, shock treatment
of the well and plumbing system prior to installation of equipment is advised.
TECHNICAL
If you will remember, our goal with the REACTR is to convert dissolved solids to suspended solids for removal
by the filter media. In the case of clear or ferrous iron, the oxygen introduced by the REACTR manifold starts
the oxidation process, which will in essence turn the iron to a physical, rusty particle. The red or ferric iron is
virtually ready for mechanical filtration since it is already precipitated.
NOTE : If a red slime type growth is observed in the water closet of a flush type toilet or growth is noted in a
sample of water after a few days, iron bacteria is likely present in the water supply.
C.
Manganese - Concentrations as low as .05 ppm of manganese can cause dark brown or black stains that ruin
clothing and fixtures and can adversely affect the color and taste of foods and beverages. Fortunately, its
occurrence in heavy concentrations is limited. There are certain things to remember when attempting to remove
manganese with a REACTR. When manganese occurs, there is usually iron also present. When iron is present,
it assists with the oxidation of manganese from the manganous (dissolved) to the manganic (precipitated) state. If
there is a 10:1 ratio of iron to manganese and there is sufficient air being drawn into the system by the
REACTR manifold, the REACTR will not have trouble removing it. For example, if there is 5.0 ppm of iron, up
to .5 ppm of manganese can be removed without concern unless the pH of the water is extremely low (we will
discuss this later). If the pH is at normal (7.0) or above and air is being drawn from 80% - 100% of each pump
cycle, a minimum of a 5:1 ratio may be possible. If a water supply contains manganese with no iron present, a
different treatment approach must be taken. In this case, the pH of the water should be raised above 8.3 by use
of a chemical feed pump feeding soda ash or caustic soda or if hardness is present, a water softener may be the
best choice. Manganese by itself in water is extremely difficult to oxidize unless the pH level is significantly into
the alkaline range. (See Figure 5.) If questions arise regarding a particular manganese situation, contact your
distributor or CSI for assistance.
D.
Turbidity - This is nothing more than physical particles suspended in water. Concentrations of a unit measure
over 1 NTU is cause for treatment. Particles can be sand, silt, scale, precipitated oxides, etc. Their removal with a
REACTR is assured due to the granular media in the filter tank.
- 72 -

Taste / Odor / Color - The REACTR is capable of improving the taste, odor and color of water due to the
multiple functions it performs. Many of these problems are corrected due to contact with air and the mechanical
filtration of organic particles. The application is wide ranging but efficient removal is determined by the root cause
of such problems.
F.
Sulfur - This term is what most people refer to when there is a rotten egg smell in their water supply. It is due to
the presence of hydrogen sulfide gas. Concentrations as low as .05 ppm are offensive to many people.
Additionally, sulfur corrodes copper, iron and brass and causes black stains on fixtures and clothing. It also affects
the taste, odor and color of foods and beverages. REACTR is capable of handling concentrations of up to 10
ppm. The air introduced into the system at the REACTR manifold, the aeration in the REACTR tank and the
scrubbing that occurs in the system, all contribute to the oxidation and conversion of hydrogen sulfide gas to
elemental sulfur particles. These particles are then removed by the filter media. Although hydrogen sulfide gas
can be oxidized at a pH level above neutral (7.0), it occurs much more readily at a pH level below 7.0. (See figure
6.) The basic thing to remember about sulfur removal with REACTR is ... the more sulfur you have, the more air
you need to be rid of it.
G.
Gases - Due to the high levels of air introduced into the system and the aeration and venting nature of the
REACTR tank, low levels of certain gases like methane, natural gas and radon gas can be driven out of the
water system. Proper venting of the system is critical to prevent an explosive situation from developing. Consult
CSI before attempting to handle elevated concentrations of these gases.
H.
pH - The pH of water is a measure of its acidity or alkalinity. As you may have guessed by reading about the other
contaminants above, pH plays a great role in the successful removal of iron, manganese and sulfur. Water with a
pH less than 7.0 is considered acidic ... with a pH above 7.0, alkaline. Water with a pH level at 7.0 is neutral. The
further away from 7.0 on either scale, the more acidic or alkaline it becomes. Acidic waters are corrosive and can
literally destroy plumbing and appliances and can cause significant staining of fixtures. The REACTR
automatically corrects the problem of low pH by two methods. Firstly, a high level of carbon dioxide in water can
form carbonic acid which obviously lowers the pH to an acid condition. When the carbon dioxide is exposed to air
(oxygen) intake at the REACTR manifold and additional exposure to air in the REACTR tank, the carbon
dioxide level is reduced, making the water less corrosive. Secondly, as the water enters the filter media, the
neutralizer material in the bed is dissolved in the water thus raising the pH level even further. If the pH of water to
be treated is below 7.0, additional neutralizer material will have to be added to the filter tank. The frequency of
adding media is in direct relation to the pH level and the volume of water being used. In a normal home,
frequency of adding material will range from 12 months to two years.
I.
Hardness - The REACTR System is not capable of removing hardness (calcium and magnesium ions) from
water. Hardness is very objectionable due to its tendency to clog piping, cause white deposits on fixtures, create
soap scum in laundry and bathing as well as increasing the operating and maintenance costs of hot water
heaters. Generally, a level of 3.5 grains per gallon (gpg) or above in the water supply should be treated. A water
softener will need to be installed after the REACTR if hardness is a problem.
J.
Tannins - Decayed organic matter in water is what is commonly referred to as tannins or humic acid. Present in
some water supplies, they can be clear or impart a light brown color and can cause problems with any oxidizing
filter. levels above .5 ppm can begin to form a viscous, sticky coating on the filter media granules. This coating
can impair the removal of precipitants and slow, if not halt, the correcting of the pH. The effect of tannins on the
REACTR vary widely due to their diverse nature. On water containing over 2 ppm, it is advisable to contact CSI
before proceeding with the installation. The OXYCLEAN Option would be recommended where tannins are
concerned.
TECHNICAL
e.
V.
Equipment Selection Procedure

We have reviewed how the REACTR works and discussed the various contaminants that can be present in a given
water supply. let's proceed with the proper method for selecting the correct equipment for the job. Please review the
specification charts below and the contaminant matrix chart (Figure 6) for REACTR capabilities.
- 73 -
General
Specifications
RF10
RF15
RF20
RF25
RF30
RF40
1.00
1.50
3.00
4.00
9x48
9x48
9X48
9x48
16x40
16x40
9x48
10x54
12X52
13x54
14x65
16x65
11
10
11
13
Smart Blend
Filter Media Type
2.00
2.50
5.0
5.0
6.0
7.0
10.0
15.0
100
100
120
140
200
300
9x9x62
9X9X62
9x9x62
Space Required (DxWxH inches) REACTRTank
9x9x62
9x9x56
128
16x16x51 16x16x51
10x10x62 12X12X60 13x13x62 14x14x73 16x16x74

160
195
255
296
430
TECHNICAL
Manganese Removal


below

If the Iron to
Then the pH must
Manganese ratio is:
be at least:
10:1
7.0
5:1
7.8
1:1
8.3
0:1
8.5
FIgURE 5
these curves
FIgURE 6
- 74 -

Step 1 : Perform a water analysis for concentrations of iron, manganese, sulfur (if rotten egg odor is detected),
pH, hardness and tannins. Are all levels within the range of performance of the REACTR? If not,
contact your distributor or CSI for assistance.
Step 2: Determine the actual pumping capacity of the water system by following this procedure.
How To Determine True Pump Capacity

1,
2.
3.
4.
5.
6.
7.
8.
9.
Open any faucet and run until pump turns on.

Close faucet and let pump fill pressure tank and turn off.
Open any faucet and collect all water discharged until pump turns on.*
When pump turns on, IMMEDIATELY close faucet and start timing pump cycle.
When pump turns off, record cycle time to refill pressure tank (in seconds).
Measure total number of gallons collected in step # 3.
Divide the number of gallons collected in step # 3 by number of seconds in step # 5.
Multiply the answer derived in step # 7 by "60".
The answer in step # 8 is the true pumping capacity of the system.
TECHNICAL
example :
Number of gallons collected during draw down (step # 3) = 9

Number of seconds in pump cycle to refill tank (step # 5) = 72
GPM
GPM
GPM
GPM
=
=
=
=
(Gallons collected / seconds in cycle) x 60

(9 / 72) x 60
.125 x 60
7.5
* Make certain no other water is being used in the system during the test!!
There are two reasons why the actual pumping capacity must be known before selecting equipment.
A.
REACTR Manifold - The REACTR Manifold must receive an adequate flow of water in order for it to
work properly. The flow requirement is a minimum of 5 gpm.
b.
Backwashing - The filter bed must receive an adequate flow of water in order to lift the contaminants
from the filter bed during backwash. The requirements are shown under the "backwash Flow Rate"
section of the specifications chart.
Model # Series
Backwash Requirements
RF10
5.0 gpm
RF15
5.0 gpm
RF20
6.0 gpm
RF25
7.0 gpm
RF30
10.0 gpm
RF40
15.0 gpm
- 75 -

Now that the flow rate has been determined and you understand its importance, a REACTR System can be selected.
below is a chart showing flow rate ranges and the REACTR by model number series that would be proper.
Calculated Pump Flow Rate (gpm)
Model #
RF10
RF15
RF25
RF30
RF40
*(2) RF25
*(2) RF30
*(3) RF15
*(3) RF25
*(3) RF30
* In Parallel
Minimum
5.0
5.0
7.0
10.0
15.0
14.0
20.0
15.0
21.0
30.0
Maximum
10.0
10.0
14.0
20.0
25.0
28.0
40.0
30.0
42.0
60.0
Note : It is advisable to contact your distributor or CSI when dealing with flow rates above 10 gpm.
VI.
Installation Tips - Please consult the REACTR Installation Instructions and Signature Series Service Manual for
specific details on installation and service procedures. Call your distributor or CSI with any questions you may have.
Do a full water analysis.
b.
Check the water closet of a flush type toilet for signs of bacterial growth (e.g. iron bacteria).
C.
Refer to the REACTR Matrix Chart (Figure 6) for contaminant limitations.
D.
Do a pump capacity test.
e.
Size the REACTR System for the backwash flow requirement.
F.
If more
1.
2.
3.
G.
The REACTR Filter will need to be loaded in the field. Always load media at the approximate location of
installation, if possible.
H.
Always plug the end of distributor tube with a cork or similar method to prevent media from entering tube.
I.
Fill the mineral tank 1/3 with water before adding media to filter tank. Add water occasionally while filling media to
help soak material.
J.
Do not use petroleum based plumber's dope or O-ring lubricant on PVC / plastic parts or O-ring connections.
Only Teflon based tape / paste and silicone O-ring lubricants are acceptable!
TECHNICAL
A.
service flow is required consider :

Use multiple residential systems in parallel.
Add a large diaphragm / bladder type pressure tank after the REACTR (stored treated water).
Consider a small commercial system.
- 76 -

K.
If sweat soldering copper pipe, protect control valve bypass and all plastic parts from heat damage.
l.
If installing REACTR tank using PVC pipe, solvent weld adapter before threading into REACTR
manifold to prevent cement from entering the venturi/nozzle section.
M.
Never connect the drain line directly to a soil line! At least a 4" air gap is required to prevent waste
water backflow into the REACTR filter.
N.
If the drain line needs to be elevated and/or exceeds 20 feet in length, increase drain line diameter to 3/4".
O.
Always install the REACTR System before water softening equipment.
VII.
Side Effects of Aeration - The following is an excerpt from the What You Should Know About Your New REACTR
Water Filter System brochure that is included with every unit. We encourage the installing contractor to make
certain the
customer reviews this information before installation.
TECHNICAL
The REACTR uses the air we breath to naturally reduce the effects of iron, manganese and sulfur gas. by introducing
oxygen to water, contaminants chemically change to a physical particle that can be mechanically filtered out of the water.
This natural process called Oxidation, is usually accomplished in other systems by using chemicals such as chlorine or
potassium permanganate. Since the REACTR does not use chemicals to treat the water, maintenance and chemical
byproducts associated with these types of systems are eliminated. The energy required to operate this system is provided
by using extra power that is available in your well pump to inject free air into the water. There are several normal side
effects that may or may not occur when water is treated in this manner:
1.
Cloudy or milky appearance to the treated water - This side effect is usually more pronounced when the iron,
manganese and sulfur gas levels are low. Since the REACTR uses oxygen for the treatment of these contaminants, it can be expected to have some amount left over in the treated water. The higher contamination levels are,
the less oxygen there will be. It is the oxygen that gives the cloudy or milky appearance. Once the faucet is
opened and the water is drawn, pressure is released and allows the oxygen to escape. This usually will take from
a few seconds to a minute depending on the amount of oxygen and the pressure. This noticeable side effect tells
you the system is working properly and will actually enhance the palatability of the water. It's oxygen that gives
water it's fresh, crisp taste.
2.
Sputtering or slight coughing from the hot water side faucets - This is a normal phenomenon that usually
occurs first thing in the morning. As the high oxygenated REACTR water is exposed to heat in the hot water
tank a small amount of oxygen will separate. The longer the water is allowed to sit in the hot water tank, the more
this will be noticed.
Usually, this will only occur if the hot water is allowed to sit idle for eight (8) hours or more. Consequently, when
hot water is drawn after an extended period of no water use, a slight sputtering or coughing may be experienced
for a few seconds. If this causes the hot water to splash out of the sink, the problem is reduced by simply turning
on the cold water first and blending in the hot for several seconds. If there is a large amount of free air noticed on
the cold water side, there is a possible malfunction of the system and your CSI Dealer should be contacted to
service the unit.
VIII.
Summary - We have attempted to review the most pertinent technical information as it relates to understanding the
REACTR Water Treatment System. This system will provide many years of service for the removal of the water
contaminants we have discussed. Proper analysis, equipment selection and installation procedures are the critical keys to
successful operation. Please refer to the REACTR Instructions and Signature Series Service Manual for complete
particulars on the proper steps for installation and troubleshooting.
- 77 -
Softener Technical Information Guide

The following information is not intended to replace attending technical training programs or reading of installation
instructions. It should be viewed as a general discussion about the product, its application, limitations and key factors to remember before purchase.
PURPOSE and CAPABILITIES: An ion exchange water softener is designed to remove (exchange) water hardness
ions (calcium & magnesium) from water supplies using specialized softening resin as the catalyst and salt (sodium)
as the regenerant. Water passes downwardly through the mineral bed where the ion exchange takes place.
Softeners can easily remove upwards of 100 grains per gallon of hardness (depending upon the cubic foot capacity).
They can also remove very high quantities (20 ppm+) of ferrous (clear water) iron and manganous (clear water)
manganese. HOWeVeR, making a softener work this hard may run you into problems of bed fouling and iron/manganese breakthrough. Additionally, the amount of salt required to regenerate resin where iron/manganese is concerned is four times that of hardness. Therefore, removing iron and manganese with a softener consumes a tremendous amount of salt and puts higher levels of sodium into the water . Standard cation exchange water softeners can
also remove or reduce Aluminum, Copper {20%-90%}, Zinc, Radium, barium, beryllium, Cadmium, Chromium (+3),
lead {20%-90%}, Mercury (+2) {20%-90%}, Nickel and Thallium. WARNINg: Although softeners can reduce the
foregoing water constituents, do not make such claims regarding health-related contaminants. Attempting to handle
such problems as those other than basic Hardness, Iron and Manganese requires special testing and equipment
application. Always check with CSI before attempting anything other than standard applications!
HARDNeSS TAble
Soft
Moderately Hard
Hard
Very Hard
0 - 3.5 gpg
3.5 - 7.0 gpg
7.0 - 10.5 gpg
10.5+ gpg
NOTe: "gpg" means grains per gallon.

LIMITATIONS: Softeners cannot remove hydrogen sulfide, iron bacteria, tannins, foul tastes, odors & colors nor
should they be used to remove anything other than very, very light sediment. Iron bacteria will eventually cause fouling and plugging of the bed. High levels of hydrogen sulfide and chlorine can damage the exchange capacity of the
mineral beads. Various size units have different hardness, iron/manganese, service and backwash flow rates. Always
consult the specification sheet in order to make a proper selection.
WATER TESTING: Always test the raw water supply for at least the following: 1) Hardness; 2) Iron; 3) Manganese;
4) pH; 5) Tannins; 6) Hydrogen Sulfide {if rotten egg odor is present}; and 7) Chlorine {if on treated water supply}.
Consult specification sheet to check for limitations.
- 78 -
Softener Technical Information Guide
TECHNICAL
INSTALLATION: Softeners should be installed on a level surface; on cold water line only; after filtration equipment;
after outside sillcock lines; and, before the piping splits to the water heater. below is a diagram of a typical installation.
Never elevate the mineral tank more than 1-2 feet above the brine tank so as not to cause problems with brine draw.
Avoid installations in direct sunlight and where freezing may occur. locate the unit near a 115V, unswitched outlet
(except manual units that require no electricity) and near a drain. Where the drain line must be elevated above the system or runs for more than 20 feet, increase the drain line size to 3/4". NeVeR decrease the size of the drain line! It is
advisable (and code in most areas) that there be at least a 4" air gap between the drain and drain line. Check all local
codes before installing equipment.
PROGRAMMING THE SYSTEM: After all plumbing has been completed according to the installation instructions, find
the section in the instructions regarding programming the control valve. It is quite simple but you must first consult your
water test results. You have determined the amount of hardness, iron, manganese, etc. Remember that iron and manganese must have special consideration. To calculate "Compensated Hardness," add the total of iron and manganese
together and multiply by four (4). Add this answer to the amount of hardness (in grains per gallon) to arrive at compensated hardness. Use this number when programming either a Timeclock or Demand initiated control valve. It is always
advisable to both disinfect the unit and test the system cycles. Consult the installation instruction manual.
REGULAR MAINTENANCE: All that's necessary for normal softener maintenance is to keep good quality softener salt
in the brine tank. Where iron/manganese are also being removed, it is a good idea to occasionally use either a resin
cleaner (Res-Up) or a bag of salt that has rust inhibitor in the formulation. Some prefer to use this type of salt instead
of standard salt. That's fine, but it is more costly. If iron bacteria has entered the system, you will need to put the system through one or more regenerations using 5.25% sodium hypochlorite (standard household bleach). Adding a cup
of bleach to the brine tank prior to regenerating will usually suffice. Should the system become terribly fouled, it may be
necessary to remove the control valve, empty the resin and wash the beads in a stronger solution. It is also a wise
move to clean the brine tank about once per year.
- 79 -
Filter Technical Information Guide

The following information is not intended to replace attending technical training programs or reading of installation
instructions. It should be viewed as a general discussion about the product, its application, limitations and key factors
to remember before purchase.
PURPOSE and CAPABILITIES: Standard whole house (point-of-entry) water filters can be used to solve many
different water problems for the home, business or farm. All work on the same principle of downflow treatment.
Filtration media are granular in design so that the granules nest tightly together to provide for excellent compaction
and filtration. After a period of time, they simply backwash (upwardly through the media to drain). The differences are
the size of tank and media selection. See the Filter Media Selection Guide for the various media and their applications. Residential filter tanks are available in 9, 10, 13, 14 and 16 inch diameters. All must have either a "D" gravel or
Garnet Sand underbed to insure a proper distribution system for both service and backwash modes.
Various medias are available for handling problems such as Turbidity (sediment), Iron, Manganese, Hydrogen
Sulfide, low pH, Taste, Odor, Color, Chlorine and Organics reduction. All but the Manganese Greensand units operate without the use of chemicals. They simply backwash, rinse then return to service position.
A specialized filter is the Upflow System. It has no control valve, instead, a simple "INleT" / "OUTleT' manifold. It
works exactly the opposite of the standard "downflow" filters. Water enters the unit first running down the distributor
tube then UP through the media. This means that it is not designed to handle sediment! Since the flow is upward, the
granules do not compact to provide the desired straining effect needed for sediment removal. The only media that
you would ever use in Upflow filters are Neutralizer and Activated Carbon. Again, refer to the Filter Media Selection
Guide for more information on media selection. Always check with CSI before attempting anything other than standard
applications!
TECHNICAL
LIMITATIONS: An automatic downflow filter must have sufficient water flow rate supplied to it for proper backwashing
to take place. It is, therefore, critical to test the output capacity of the pumping or water supply system before making
a selection. It is often the case that filters require more water for backwash than they can offer in treated, service
flow. Another limitation is that of service flow. If you attempt to get too much water through a filter, one of two things
will
happen. First, the water may not be completely treated leaving stains, odors, etc. in the finished service water.
Secondly, there may be tremendous pressure drop across the filter bed if too much water is forced through the filter.
Proper sizing is critical! Check the individual specifications sheets for backwash requirements and service flows.
- 80 -
Filter Technical Information Guide

hOW TO DETERMINE PUMP CAPACITY
1. Open any faucet and run until pump turns on.
2. Close faucet and let pump fill pressure tank and turn off.
3. Open any faucet and collect all water discharged until pump turns on.
4. When pump turns on, immediately close faucet and start timing pump cycle.
5. When pump turns off, record cycle time to refill pressure tank (in seconds).
6. Measure total number of gallons collected in step #3.
7. Divide the number of gallons collected in step #3 by the number of seconds in step #5.
8. Multiply the answer derived in step #7 by 60.
9. The answer in step #8 is the average pumping capacity of the system.
(Note: Make certain no other water is being used during this test)
TECHNICAL
Example
Number of gallons collected during draw-down (step #3) = 9
Number of seconds in pump cycle to refill tank (step #5) = 72
GPM = (gallons collected / seconds in cycle) X 60
GPM = ( 9 / 72 ) X 60
GPM = .125 X 60
GPM = 7.5
(Simply select a filter requiring 7.5 gpm, or less, backwash)
WATER TESTING: Always test the raw water supply for at least the following: 1) Hardness; 2) Iron; 3) Manganese; 4)
pH; 5) Tannins; 6) Hydrogen Sulfide {if rotten egg odor is present}; and 7) Chlorine {if on treated water supply}. Consult
specification sheet to check for limitations.
INSTALLATION: Filters should be installed on a level surface; on cold water line only; typically after outside sillcock
lines; before softeners; and, before the piping splits to the water heater. Above is a diagram of a typical installation.
Avoid installations in direct sunlight and where freezing may occur. locate the unit near a 115V , unswitched outlet
(except manual units that require no electricity) and near a drain. Where the drain line must be elevated above the system or runs for more than 20 feet, increase the drain line size to 3/4 ". NeVeR decrease the size of the drain line! It is
advisable (and code in most areas) that there be at least a 4" air gap between the drain and drain line. Check all local
water test results. You have determined the pH, amount of iron, manganese, etc. It's typical to set filters to backwash
from every 3 to 6 days. It is always advisable to both disinfect the unit and test the system cycles. Consult the
installation instruction manual.
REGULAR MAINTENANCE: All that's necessary for normal filter maintenance is regular backwashing. If iron bacteria
has entered the system, you will need to remove the control valve and add 5.25% sodium hypochlorite (standard
household bleach), leave it sit for at least 30 minutes then backwash. Should the system become terribly fouled, it may
be necessary to empty the filter bed washing the granules in a stronger solution. If this doesn't sufficiently clean the
medium, a replacement bed will be necessary. You'll need to replace and/ or replenish media according to the Filter
Media Selection Guide.
- 81 -
Chemical Feeding Technical Information Guide

The following is not intended to replace attending technical training programs or reading of installation instructions.
It should be viewed as a general discussion about the product, its application, limitations and key factors to remember before purchase.
PURPOSE and CAPABILITIES: Chemical feeding can serve a number of purposes including feeding chlorine for
disinfection and oxidation of certain contaminants such as iron, manganese, hydrogen sulfide, tannins and organic
complexes. It is also useful for controlling pH levels. Selecting the right chemical feed pump is critical for proper
treatment. The following formula applies whether disinfecting, oxidizing or controlling pH:
Well Pump
Output X
(gpm)
Required
Solution
Dosage X 1440/Strength
(ppm)
(ppm)
FeeD PUMP OUTPUT

(Gallons per Day)
Well Output Rate - Use the following formula for determining pump capacity:
hOW TO DETERMINE PUMP CAPACITY
TECHNICAL
1. Open any faucet and run until pump turns on.

2. Close faucet and let pump fill pressure tank and turn off.
3. Open any faucet and collect all water discharge until pump turns on.
4. When pump turns on, immediately close faucet and start timing pump cycle.
5. When pump turns off, record cycle time to refill pressure tank (in seconds).
6. Measure total number of gallons collected in step #3.
7. Divide the number of gallons collected in step #3 by the number of seconds in step #5.
8. Multiply the answer derived in step #7 by 60.
9. The answer in step #8 is the average pumping capacity of the system.
(NOTe: Make certain no other water is being used during this test)
Example
Number of gallons collected during draw-down (step #3) = 9
Number of seconds in pump cycle to refill tank (step #5) = 72
GPM = (gallons collected / seconds in cycle) X 60
GPM = (9 / 72 ) X 60
GPM = .125 X 60
GPM = 7.5
Dosage Required - The following are chlorine dosage requirements for common water constituents:
1
1
1
1
For Every ......
Chlorine Required .....
ppm Hydrogen Sulfide

ppm Iron
ppm Manganese
ppm Tannin
3 ppm
1 ppm
1-2 ppm
1-3 ppm
Simply multiply the required amounts of chlorine by the ppm presence of each contaminant and add them together.
Also, remember that it is usually necessary to have a chlorine residual of, say, 1 ppm after contact time. Whatever
answer you determine, add 1 ppm for the residual.
- 82 -
Chemical Feeding Technical Information Guide

Solution Strength - The following are strengths of typical chemicals for feeding:
Chemical
Strength
8.0% Chlorine bleach
80,000 ppm
12.5% Chlorine bleach
125,000 ppm
Potassium Permanganate
(1/4# per gallon water)
Polyphosphate
(1# per 10 gallons water)
Soda Ash
(.926# per 1 gallon water)
30,000 ppm
12,000 ppm
10% Solution
SAMPLE CALCULATION:
TECHNICAL
Youve determined that the pump capacity was 10.5 gallons per minute. There are 2 ppm Iron; 4 ppm Hydrogen Sulfide;
and, a 1 ppm Residual is desired. Simply multiply the 2 ppm Iron by its dosage requirement factor of 1 (2 X 1 = 2); multiply the 4 ppm Hydrogen Sulfide by its factor of 3 (4 X 3 = 12). Add the totals (2 + 12 = 14) then add the residual amount
to that total (14 + 1 = 15) for the dosage required. If you are feeding 8.0% chlorine bleach full strength, you can now calculate the above formula to determine the number of gallons per day that will be fed in this example.
(10.5 gpm) X (15 ppm) X (1440) / (80,000) = 2.84 gallons per day
In this example, 2.84 gallons of chlorine bleach will need to be fed to insure that all contaminants are oxidized and a
1 ppm residual of chlorine is left over.
It is now necessary to choose a chemical feed pump that will deliver 2.84 gallons of chlorine in a 24 hour period. For
example, choosing a 7 gpd with a maximum output daily would be a correct choice. However, a pump should not be
set below 30% of its setting. To check your selection, simply divide the required output by the capacity of the pump...
in this case, 2.84 / 7.0 = 44.3%. Therefore, the setting would be at 47% and above the 30% mark. If, however, you
were diluting the chlorine (say 3 parts water to 1 part chlorine), you would need to select a 24 gpd since the daily
output would be 11.36 gallons of solution. (8.52 + 2.84 = 11.36 ) Remember, proper sizing is critical! Check the individual specification sheets and contact your Distributor or CSI with questions.
- 83 -
Tannin/Hardness Technical Information Guide

The following is not intended to replace attending technical training programs or reading of installation instructions.
It should be viewed as a general discussion about the product, its application, limitations and key factors to
remember before purchase.
PURPOSE and CAPABILITIES: The Tannin/Hardness ion exchange equipment is designed to remove (exchange)
water hardness ions (calcium & magnesium) and organic tannins from water supplies using a combination of specialized resins as catalyts using salt (sodium) as the regenerant. Water passes downwardly through the mineral
bed where the ion exchange takes place. These systems can easily remove hardness and tannins when they
occur in water (depending on the cubic foot capacity). They cannot remove iron, manganese, sulphur and other
water constituents. Attempting to do so may run you into problems of bed fouling and hardness/tannin breakthrough. Always check with CSI before attempting anything other than standard applications!
hARDNESS TABLE
Soft
0 - 3.5 gpg
Moderately Hard
3.5 - 7.0 gpg
Hard
7.0 - 10.5 gpg

10.5 + gpg
Note: gpg means grains per gallon.
4) pH; 5) Tannins; 6) Hydrogen Sulfide (if rotten egg odor is present); 7) Chlorine (if on treated water supply).
Consult specification sheet to check for limitations.
TECHNICAL
Very Hard
RAW WATER LIMITATIONS

Free Chlorine
Turbidity
0.1 ppm
5 units
Iron
0.50 ppm
Manganese
0.50 ppm
Hydrogen Sulfide
0.1 ppm
Note: ppm means parts per million - gpg means grains per gallon.
NOTe: For limitations, Installation, Programming and Maintenance, refer to the Softener Technical Information
Guide as Tannin/Hardness units have the same requirements.
- 84 -
R/O Technical Information Guide

The following is not intended to replace attending technical training programs or reading of installation instructions. It
should be viewed as a general discussion about the product, its application, limitations and key factors to remember
before purchase.
PURPOSE and CAPABILITIES: Reverse Osmosis systems are highly specialized water treatment devices that deal
with contaminants at the molecular level. Influent water passes through a membrane that allows water to pass to a
storage tank (service) and rejects the contaminants running them to a drain. They work very slowly to produce high
quality water and must have significant water pressure in order to work properly. The TDS (total dissolved solids) are
significantly reduced through R/O systems.
TECHNICAL
LIMITATIONS: An R/O system must receive water that is pretreated for best results. Iron, manganese, hydrogen sulfide, and hardness should be reduced to minimum levels. They are limited to small quantities of output water per day
with CTA (Cellulose Tri Acetate) systems producing 14 gallons per day and TFC (Thin Film Composite) systems
upwards of 24 gallons per day. Check the individual specification sheets for requirements and limitations.
WATER TESTING: Always test the raw water supply for at least the following: 1) Hardness; 2) Iron; 3) Manganese; 4)
pH; 5) Tannins; 6) Hydrogen Sulfide (if rotten egg odor is present); 7) Chlorine (if on treated water supply); and, 8)
TDS. Consult specification sheet to check limitations.
INSTALLATION: R/O systems are typically installed under the kitchen sink, in closets or basements with a treated line
running to the kitchen sink faucet provided with each unit. If air gap systems are required in your state or local areas,
make certain that you order and install the proper system.
PROGRAMMING THE SYSTEM: There is nothing to program on an R/O system. Simply connect to source plumbing
and drain line.
REGULAR MAINTENANCE: The membrane of an R/O system should be replaced at least every 12 months. The pre
and post-filter elements should be replaced every 6 months. It is also advisable to completely drain the system (simply
using the faucet) periodically to insure that the water in the storage tank is fresh. Complete maintenance details are
included with each set of installation instructions.
- 85 -
Nitrate/Sulfate Technical Information Guide

before purchase.
PURPOSE and CAPABILITIES: An ion exchange Nitrate/Sulfate system is designed to remove (exchange) nitrate
and sulphate ions from water supplies using a very specialized resin as the catalyst and salt (sodium) as the regenerant. Water passes downwardly through the mineral bed where the ion exchange takes place. These systems can
easily remove these constituents (depending upon the cubic foot capacity). They are not designed to remove hardness, iron or manganese! As a matter of fact, the water should be pretreated (if necessary) so that certain other contaminants are not present in the water to be treated. If they are not removed, you may run into some problems of bed
fouling and nitrate/sulphate breakthrough. The amount of salt (per cubic foot of resin) required to backwash these
systems is actually less than that required to regenerate a softener of a similar size.
WARNINg: Although these systems can reduce the foregoing water constituents, YOU MUST make certain
that you take precautions for proper sizing, installation and water testing since these constituents (especially nitrates) can have serious health-related consequences!! Always check with CSI before attempting anything
other than standard applications!
RAW WATeR lIMITATIONS

0.5 ppm
Turbidity
5 units
Iron
0.1 ppm
Manganese
0.1 ppm
Hydrogen Sulfide
0.1 ppm
Tannins
0.5 ppm
Hardness
TECHNICAL
Free Chlorine
Preferably less than 5 gpg
Note: ppm means parts per million - gpg means grains per gallon.
LIMITATIONS: Remember, Nitrate/Sulphate systems cannot remove hardness, iron, manganese, hydrogen sulfide,
iron / manganese / sulfur bacteria, tannins, tastes, odors & colors nor should they be used to remove anything other
than Nitrates and Sulphates. Presence of any of the above constituents can cause these systems to become less
efficient or fail to remove nitrates and sulphates! Various size units have different service and backwash flow rates.
Always consult the specification sheet in order to make a proper selection.
4) pH; 5) Tannins; 6) Hydrogen Sulfide (if rotten egg odor is present); 7) Chlorine (if on treated water supply); 8)
Nitrates as N (nitrogen); 9) Nitrates as NO3 (nitrate); and 10) Sulphates as SO4 (sulphate)
INSTALLATION: Nitrate / Sulphate systems should be installed on a level surface, on cold water line only; after
filtration and softeners; after outside sillcock lines; and, before the piping splits to the water heater. Note typical
installation.
- 86 -
TECHNICAL
Nitrate/Sulfate Technical Information Guide
Never elevate the mineral tank more than 1-2 feet above the brine tank so as not to cause problems with brine draw.
Avoid installations in direct sunlight and where freezing may occur. locate the unit near a 115V, unswitched outlet
(except manual units that require no electricity) and near a drain. Where the drain line must be elevated above the system or runs more than 20 feet, increase the drain line size to 3/4. NeVeR decrease the size of the drain line! It is
advisable (and code in most areas) that there be at least a 4 air gap between the drain and drain line. Check all local
water test results. Refer to the Capacity/Regeneration box in order to determine the regeneration frequency for
either Timeclock or Demand initiated control valves. Always check system cycles and consult the installation instruction
manual.
REGULAR MAINTENANCE: All thats necessary for normal maintenance is to keep good quality softener salt in the
brine tank. Should the system become fouled, it may be necessary to remove the control valve, empty the resin and
wash the beads. It is also wise to clean the brine tank about once per year.
Capacity/Regeneration
In order to properly size Nitrate/Sulphate systems, the amounts of each in the raw water must be known. They must
be expressed as equivalents as calcium carbonate (CaCO3). Use the test results and follow these steps:
Sulphate as SO4 ppm X 1.04 = Sulphate ppm as CaCo3
Nitrate as N ppm X 3.56 = Nitrate as CaCO3
Nitrate as NO3 ppm X 0.81 = Nitrate as CaCO3
Add all CaCO3 ppm quantities together and divide by 17.1 to find equivalent grains per gallon (gpg). Then, divide
the total grain capacity of the unit by the gpg of CaCO3 to determine how many gallons can be treated before
regeneration.
- 87 -
U/V Technical Information Guide

before purchase.
PURPOSE and CAPABILITIES: Ultra Violet systems are highly specialized water treatment devices that disinfect
water. Influent water passes through the cylindrical, stainless steel chamber where a certain wavelength of light
destroys or deactivates many bacteria and viruses. each unit has a built-in flow control so that proper contact time
can be maintained to insure high disinfection rates.
LIMITATIONS: An Ultra Violet system must receive water that is pretreated for best results. Iron, manganese, hydrogen sulfide, and hardness should be reduced to minimum levels. They are not designed to kill forms of iron/manganese/sulfur bacteria nor cysts like Giardia lamblia. As a matter of fact, tannins and slime producing bacteria (iron
bacteria) coat the quartz tube and reduce light penetration. See specification sheet for requirements and limitations.
TECHNICAL
4) pH; 5) Tannins; 6) Hydrogen Sulfide (if rotten egg odor is present); 7) Chlorine (if on treated water supply); and, 8)
TDS. Consult specification sheet to check limitations.
INSTALLATION: U/V systems are typically installed at the point-of-entry in a home or business where all water can
be treated. It is strongly advisable to install a drain on the lower section of the plumbing for easy draining during
cleaning. Make certain that it is connected to an uninterrupted power supply!
PROGRAMMING THE SYSTEM: There is nothing to program on a U/V system. Simply connect to source plumbing
and power supply.
REGULAR MAINTENANCE: The U/V lamp should be replaced annually and the entire unit cleaned about every six
months to prevent build-up on the quartz tube. It is also advisable to use a strong chlorine solution in the stainless
steel housing each time the system is cleaned. If the unit has a failsafe feature, check the solenoid for proper operation. Complete details on preventative maintenance are included with each set of installation instructions.
- 88 -
Granular Activated Carbon Reduction Capability
TECHNICAL
Name of
Contaminant
- 89 -
1.1.1-Trichloroethane
1.1.2.2-Tetrachloroethane
1.1.2.2-Tetrachloroethylene
1.1.2-Trichloroethane
1.1-Dichloroethane
1.1-Dichloroethylene
1.1.2.4-Trichlorobenzene
1.2-Dichlorobenzene
1.2-Dichloroethane
1.2-Dichlorothylene
1.2-Dichloropropane
1.2-Diphenyl Hydrazline
1.3-Dibromochloromethane
1.3-Dichlorobenzene
1.3-Dichloropropane
1.4-Dichlorobenzene
2.4.5-TP
2.4.6-Trichlorophenol
2.4-Dimethylphenol
2.4-Dichlorophenal
2.4-Dinitrophenol
2.4-Dinitrotoluene
2.6-Dinitrotouene
2-Chloroethyl Vinyl ether
2-Chloronaphthalene
2-Chlorophenol
2-Methyl-4.6-Dinitrophenol
2-Nitrophenol
4.4-DDD
4.4-DDe
4.4-DDT
4-bromophenyl Phenyl ether
4-Chlorophenyl Phenyl ether
4-Nitrophenol
Acenaphthene
Acenaphthylene
Acrolein
Aldrin
Alhpa-bHC
Anthracene
benzene
benzidine
benza (a) Pyrene
benza (b) Fluoranthene
beta-bHC
bis (2-Chloroethoxy) Methane
bis (2-Chloroethyl) ether
bis (2-Chloroisopropyl) ether
bis (2-ethylhexyl) Phthalate
bix (Chloromethyl) ether
bromodichloromethane
bromofrom
butyl benzyl Phthalate
Carbon Tetrachloride
Chloramines
Chlordane
Chlorobenzene
Chloroform
Chrysene
Di-n-octylphthalate
Dibutyl Phthalate
Dichlorodifluoromethane
Dieldrin
Diesel Fuel
Diethyl Phthalate
Dimethyl Phthalate
Dioxin
eDb
endosulfan I
endosulfan II
endosulfan Sulfate
endrin
ethylbenzene
Fluoranthene
Fluorene
No
Removal
Modest
Removal
Good
Removal
excellent
Removal
Name of
Contaminant
Fuel Oil
Gasoline
Heptachlor
Heptachlor epoxide
Hexachlorobenzene
Hexachlorobutadiene
Hexachlorocyclopentadiene
Hexachloroethane
Isophorone
Kerosine
lindane
Malathion
Methane
Methoxychlor
Methyl bromide
Methylene Chloride
n-Nitroso-n-Propylamine
n-Nitrosodimethylamine
n-Nitrodoiphenyl Amine
Naphtalene
Nitrobenzene
Oil
Parathion
PCb's
PCb-1016
PCb-1221
PCb-1232
PCb-1242
PCb-1248
PCb-1254
PCb-1260
Pentachlorophenol
Phenanthrene
Phenol
Pyrene
TCA
TCe
Toluene
Total Organic Carbons
Toxaphene
Toxic Herbicides
Toxic Insecticides
Toxic Pesticides
Trichloroethylene
Trichlorofluoromethane
Trihalomethanes (THM's)
Unpleasant Colors
Unpleasant Odors
Unpleasant Tastes
Aluminum
Arsenic
Asbestos
barium Sulfate
Cadmium Oxide
Calcium
Chlorides
Chlorine
Chromium Oxide
Copper Oxide
Fluoride
Hydrogen Sulfide Gas (Sulfur)
Iodine
Iron Oxide
lead Chromate
Magnesium
Manganese Oxide
Mercury
Nickel Oxide
Nitrates
Selenium
Silver Chloride
Sodium
Toxic Heavy Metals
Turbidity (Sediment & Scale)
Zinc Oxide
No
Removal
Modest
Removal
Good
Removal
excellent
Removal
Water Use estimates

Dwellings
Airports
Per Passenger = 3 - 5 gal. / day
Apartments
based on 3 persons per apartment
Hot and Cold = 150 gal. / unit / day
Hot Only
= 60 gal. / unit /day
Barber Shops
boarding Houses
= 50 gal. / person / day
luxury = 100-150 gal. / person / day
Multiple Family Apts.
Rooming Houses
Single Family
= 50-75 gal. / person / day
55 gal. / chair / day
Beauty Salons
Factories
15 - 35 gal. / person/ shift
270 gal. / station / day
Hospitals
Boilers
Hotels
With Private baths (2 persons)
= 60 gal. / day
Without Private baths
Laundry
Hot and Cold = 2.5 x lb. capacity is
equivalent to gallons per cycle
Lawns
25 gal. / square foot / season
Camps
Hot and Cold = 20 gal. / person / day

Hot Only
Parks
Overnight with flush toilets
= 25 gal. / camper / day
Trailers with individual bath units
= 50 gal. / camper / day
Picnic Areas
With bath houses, showers and flush
toilets = 20 gal. / picknicker / day
With toilet facilities only
= 10 gal. / picknicker / day
Schools
elementary :
Hot and Cold = 13 gal. / student / day
Hot Only
= 5 gal. / student / day
Junior High :
Hot Only
Senior High:
Hot Only
TECHNICAL
To determine daily makeup in gallons:

1. Multiply boiler h.p. by 4.25.
2. Then multiply by hours per day of
operation.
3. Then multiply by the % operating
rating.
4. Then subtract the % condensate
returns.
Note: When ratings are given in
pounds of steam per hour, divide by
500 to obtain GPM requirement. When
ratings are given in bTUs divide by
12,000. For every 12,000 bTUs, there
is an equivalent of 1 h.p.
Meter reading preferred

Hot and Cold = 250 gal. / bed / day
Hot Only
= 170 gal. / bed / day
Office Buildings
Service Stations
10 gal. / vehicle / day
Shopping Centers
Day (No meals) = 15 gal. / person/day Livestock & Poultry
300 gal. / 1,000 square foot / day

Cow, beef = 12 gal. / animal / day
Resorts
= 50 gal. / person/day
Cow, Dairy = 20 gal. / animal / day Stores
Tourist
= 35 gal. / person/day
Goat
= 2 gal. / animal / day
400 gal. / toilet room / day
Hog
Cooling Water
Horse
To determine daily makeup in gallons: Mule
= 12 gal. / animal / day Swimming Pools
10 gal. / swimmer / day
Sheep
1. Multiply the tonnage by four (this
Chickens = 10 gal. / each 100 / day
includes 2 gal. / hr / day / ton bleed
Turkeys
= 18 gal. / each 100 / day Theaters
off).
Indoor = 5 gal. / auditorium seat / day
2. Then multiply by the number of
Drive-In = 5 gal. / car space / day
hours per day of operation.
Motels
With bed and toilet (no kitchen)
40 gal. / bed space / day
Trailer Parks
Dentist
150 gal. / trailer / day
4,000 gal. / month / chair
Dormitories
Hot and Cold = 40 gal. / person / day
Hot Only
Nursing Homes
Hot and Cold = 100 gal. / bed / day
Hot Only
= 50 gal. / bed / day
Workers
Construction = 50 gal. / person / shift
Office
= 15 gal. / person / shift
- 90 -
estimating Flow Rate Requirements

The following information describes estimated maximum GPM flows from certain typical fixtures and appliances.
estimates do not consider water saving devices. The fixture count columns are factors to be used to determine
estimated flow rate requirement for homes, apartments and commercial facilities. Other types of equipment not listed
below, but present on the premises must be also considered in the analysis.
ESTIMATED FLOW
RATE
(gpm)
RESIDENTIAL
FIXTURE
UNITS
PUBLIC
FIXTURE
UNITS
lavatory
bathtub
Shower Head
Toilet (with flush tank)
Toilet (with flush meter)
15
10
Urinal (with flush tank)
---
Urinal (with flush meter)
10
---
Kitchen Sink
Dishwasher
laundry Tray / Service Sink
Automatic Clothes Washer
.75
.25
.50
TECHNICAL
FIXTURE / APPLIANCE
Drinking Water Faucet / Water Fountain
NOTe 1: Check with manufacturer of appliance or consult specifications manual for exact flow rate.
Flow
RATES
(gpm)
TOTAL
USAgE
(gallons)
Shower / bath Tub
lavatory Sink
NUMBER of BAThROOMS in the hOME
11/2
2-21/2
3-4
35
35
35
53
70
Toilet
10
15
20
Kitchen Sink
Automatic Washer
35
--
18
18
18
Dishwasher
14
--
--
Seven Minute *Peak Demand
--
--
45
70
98
122
Minimum Sized Pump Required
--
--
7 gpm
10 gpm
14 gpm
17 gpm
Minimum Treatment equipment Reqd.
--
--
5 gpm
6 gpm
7 gpm
10 gpm
OUTLETS
* Peak demand can occur several times during morning and evening.
NOTe 1: It is always better to have larger flow rate capacity treatment equipment if the pump capacity is available for
backwashing.
NOTe 2: Chart b was adapted from Ground Water Age magazine, December 1991, page 22.
- 91 -
Plotting Service Flow Rates

20
19
17
18
40
17
16
14
13
12
10
11
20
10
9
7
12
7
6
TECHNICAL
REQUIRED FLOW RATE IN gPM
15
4
3
2
1
0
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
TOTAL FIXTURE UNIT COUNT

In reading the above chart, use the vertical line to the right of the horizontal numbers. Use the line above the vertical numbers.
hOW TO USE ThIS TABLE

The estimated flow rate requirement for plumbing fixtures used intermittently on a water supply line may be obtained
by multiplying the number of each kind of fixture times its individual fixture count value as determined from Table A on
the previous page entitled ESTIMATING FLOW RATE REQUIREMENTS. Add the sums together to get a grand total
fixture unit count.
looking at the chart above, find the fixture count on the lower edge of the chart that most closely matches the number
you calculated. At that point, go upward on the vertical line until you hit the curve on the chart. Follow the intersecting
horizontal line to the left in order to determine the flow rate requirement for treatment equipment. The gpm flow rate
that is discovered using this chart will be very adequate for the facility. You could actually use about 70% of the
number as a minimum for equipment sizing.
Remember that estimating charts and tables are just that.....estimates. The more information you have, the better
your calculations will be. Also refer to Table b on the previous page for more rules-of-thumb on treatment
requirements in gpm based on number of bathrooms in the home.
- 92 -
Water Well Disinfection
Shock Chlorination Procedure

Shock Chlorination is the procedure for cleaning and sanitizing a well or spring with chlorine.
Concentrations of chlorine used in shock chlorination are 100 to 400 times the amount of
chlorine found in city water. The highly chlorinated water is held in the pipes for 12 to 24
hours before it is flushed out and the system is ready for use.
Periodic shock chlorination may also be effective to reduce an iron bacteria problem.
For wells, the amount of chlorine needed to shock chlorinate a water system is determined
by the amount of water standing in the well. Table 1 lists the amount of chlorine laundry
bleach or powdered high-test hypochlorite (HTH) needed for wells. If in doubt, it is better to
use more chlorine than less.
Table 1
TECHNICAL
Amount of chlorine needed for shock chlorination

laundry bleach (about 8% Hypochlorite)
Depth of
Water in
well
4 inch
6 inch
8 inch
10 inch
12 inch
10 feet
25
50
100
150
1/2 cup
1 cup
1 pint
1 quart
3 pints
1 cup
1 pint
1 quart
2 quarts
3 quarts
1 1/2 cup
2 pints
2 quarts
1 gallon
1 1/2 gallon
1 pint
3 pints
3 quarts
1 1/2 gallon
2 gallons
2 pints
4 1/2 gallons
1 gallon
2 gallons
3 gallons
Casing Diameter
High-Test Hypochlorite (HTH 65-75% Hypochlorite)

Depth of
Water in
well
4 inch
6 inch
8 inch
10 inch
12 inch
10 feet
25
50
100
150
----1/4 lb.
---1/3 lb.
1/2 lb.
--1/3 lb.
3/4 lb.
1 lb.
-1/4 lb.
1/2 lb.
1 lb.
1 1/2 lb.
-1/2 lb.
3/4 lb.
1 1/2 lb.
2 lbs.
Casing Diameter
- 93 -
Water Well Disinfection

To Shock Chlorinate a Well:
Pour the proper amount of chlorine bleach or powdered chlorine dissolved in a small
amount of water directly into the well.
2.
Connect a garden hose to a nearby faucet and wash down the inside of the well.
3.
Re-circulate the chlorinated water into the well for a minimum of one (1) hour (2 to 3
hours is preferable).
4.
Open each faucet one by one and let water run until a strong odor of chlorine is
detected. If a strong odor is not detected, add more chlorine to the well.
Note: bypass all installed water treatment equipment.
5.
let the water stand in the water system for at least 12 to 24 hours.
6.
Flush the system of remaining chlorine. Start by turning on outside faucets and letting
them run until the chlorine smell dissipates. let the water run on the ground to reduce
the load on your septic system. Finally, run the indoor faucets until the system is
completely flushed.
Shocking chlorination of a spring is more difficult. If possible, divert spring water away from
the spring box. Mix about 1/2 cup of household bleach in 5 gallons of water and scrub the walls
of the spring box or holding tank or both. Return the flow of spring water back into the spring
box and let the fresh water carry the chlorine through the pipeline to disinfect the plumbing.
TECHNICAL
1.
Most water treatment equipment, such as water softeners and iron filters, should be
bypassed. Check the manufacturers literature before chlorinating treatment equipment and
pressure tank to prevent damage from strong chlorine solutions. Do not chlorinate carbon or
charcoal filters; doing so will use up their capacity. Rebedding of these type fixtures will be
required.
Be Careful when handling concentrated chlorine solutions. Wear rubber gloves, goggles and
protective apron. If chlorine accidently gets on your skin, flush immediately with clean water.
Never mix chlorine solutions with other cleaning agents or ammonia, because toxic gases are
formed.
Do not use fresh scent bleach or other special laundry products to disinfect wells. Use the
plain and usually least expensive laundry bleach.
Retest your water supply for bacteria after waiting 1 to 2 weeks. If shock chlorination does not
eliminate a bacteria problem, continuous disinfection may be necessary.
Ref: OCeSOhio Cooperative extension Service
- 94 -
Softener Regeneration Guide
The following will help you in determining how to program a Timeclock softener for regeneration.
If you have a Demand system, this chart is not necessary as the control valve decides when to
regenerate.
DETERMINE
Hardness (in gpg)
Iron & Manganese (in ppm - combined)
Number of persons in the family
Capacity of the softener (total grains)
TECHNICAL
STEP #1: Figure number of gallons used per day

# of people x 75
STEP #2: Figure Compensated Hardness
gpg of Hardness + (ppm Iron/Manganese x 4)
STEP #3: Figure total grains used per day
Step #1 answer x Step #2 answer
STEP #4: Figure Days between Regenerations
Softener Capacity / Step #3 answer
EXAMPLE
YOUR
CALCULATION
20
2
4
32,000
300
28
8,400
3.81
NOTe: Always round down to the next lowest number of days between regeneration when
programming. In the example above, the answer was 3.81 days between regenerations. For a
32,000 Grain Capacity Softner you would set the softener to regenerate every 3 days.
- 95 -
Problem Cause / effect / Remedy Guide

PROBABLE
CAUSE
gENERAL
EFFECT
PROBABLE
REMEDY
hARDNESS
(calcium & magnesium)
Scale in pipes and water heaters; causes soap

curd on fixtures, tile, dishes and laundry; low
sudsing characteristics.
Removal by ion exchange

softener.
IRON/MANgANESE
Causes discolored water; red, brown, orange or

black stains on fixtures, appliances and laundry;
dark scale in pipes and water heaters.
low level (2ppm) removal

by ion exchange softener
when hardness is also present; best removed by
oxidizing iron filter; aeration
and/or chlorination followed
by filtration in some cases.
IRON/MANgANESE/SULFUR Same general effects as above plus slimy deposits low level removal possible
by oxidizing iron filter; best
Bacteria
that form in pumps, pipes, softeners and toilet
removed by chlorination
tanks.
followed by filtration.
hYDROgEN SULFIDE
gAS
best removed by aeration,

scrubbing and filtration; also
removed by oxidizing filters
or chlorination followed by
filtration.
TUBIDITY
Suspend matter in water; examples include mud,

clay, silt and sand; can ruin seats, seals and
moving parts in appliances.
Removal by backwashing
sediment filters; extra fine
treatment utilizing sediment
cartridge elements.
ACID WATER
(low ph)
Corrosive water attacks piping and other metals,

red and/or green staining of fixtures and laundry.
best corrected by
neutralizing filters or soda
ash feeding.
Depending on the nature of
contaminant, aeration followed by filtration; carbon
filtration; chlorination
followed by filtration.
TASTE/ODOR/COLOR
(organic matter)
Makes water unpalatable; can cause staining.
TANNINS/hUMIC ACID
Can impart an iced-tea color to water; causes

light staining; can affect the taste of foods and
beverages.
Can cause serious disease and intestinal disorders.
Removal by special ion

exchange or oxidizing
agents and filtration.
Chlorination and filtration is
most widely practiced; iodination, ozonation and ultraviolet treatment are used to
a lesser degree.
Can cause serious disease and/or poisoning.
Most are readily removed by

absorption with carbon
filters; some can also be
removed by hydrolysis and
oxidation.
COLIFORM BACTERIA
ORgANIC hALIDES
(e.g. herbicides &
Pesticides)
NITRATES/ChLORIDES
& SULPhATES
SODIUM SALTS
TECHNICAL
Foul rotten-egg odor; corrosion to plumbing;

tarnishes silver and stains fixtures and laundry;
ruins the taste of foods and beverages.
Can cause health-related problems if quantities are Removal by special ion

exchange, deionization
high.
process or reverse osmosis.
Imparts an alkaline or soda taste to water.
Removal by deionization
process or reverse osmosis;
distillation can be used.
- 96 -
CSI Water Treatment Freeboard Chart
Model Number
From Top of Tank

to Mineral
CT24, CM24
8
12
17
21
20
17
28
24
24
14
18
17
13
18
17
CT32, CM32
TS24, MS24, AT24, TST24, MST24
TS96, MS96, AT96
TECHNICAL
TS128, MS128
WF40, UT40, UTP40, UTP40VS
TSI24, MSI24, ATI24
TSI32, MSI32, ATI32
TSI48, MSI48, ATI48
TSI64, MSI64, ATI64
U10, WF10, RF10, RF10VS, UT10, IF10
U15, WF15, RF15, UT15, UTP15, IF15,
RF15VS, UTP15VS
U20, WF20, RF20, UT20, IF20, RF20VS,
UTP20, UTP20VS
15
U25, WF25, RF25, UT25, IF25, RF25VS,

UTP25, UTP25VS
WF30, RF30, UT30, RF30VS, UTP30,
UTP30VS
18
28
- 97 -
Slot Opening equivalents

The following chart details the opening sizes of slots for distributor systems and screens.
Microns
U.S. STD. Mesh *
.0002
--
.0006
15
1000
.001
25
--
.0012
30
500
.0015
37
400
.002
50
270
.0024
61
250
.003
75
200
.004
100
150
.005
125
120
.006
149
100
.007
177
80
.008
200
70
.010
250
60
.012
305
50
.014
355
45
.016
400
40
.020
500
35
.023
590
30
.028
710
25
.033
840
20
.039
1000
18
.047
1190
16
.055
1410
14
.066
1680
12
.094
2380
.111
2790
.132
3330
.157
4000
TECHNICAL
Inches
*Note: The higher the Mesh number, the finer job of filtration it will do.
- 98 -
Mathematical Conversions
TECHNICAL
To Convert
From
To
Multiply By
To Convert
From
To
Multiply By
Acre
Square Feet
43,560
Gallon (US liq)
Ounce (US fluid)
128
Acre-Foot
Cubic Yard
1613.333
Gallon (US liq)
Pint (US liq)
Angstrom
Nanometer
0.1
Gallon (US liq)
Quart (USliq)
Atmosphere
Foot of H20
33.89854
Gallon (brit)
Gallon (US liq)
1.200950
bar
Atmosphere
0.9869233
Grain/Gal (brit)
Milligram/liter
14.25377
bushel
Cubic Foot
1.244456
Grain/Gal (US)
Milligram/liter
17.11806
bushel
Gallon (US liq)
9.309177
Inch
Centimeter
2.54
Centimeter
Foot
0.03280840
Inch
Millimeter
25.4
Centimeter
Inch
0.3937008
Kilogram
Grains
15,432.358
Centimeter
Micrometer
10,000
Kilogram
Pounds
2.2046226
Centimeter
Millimeter
10
liter
Cubic Feet
0.03531467
Chain(Gunters)
Feet
66
liter
Cubic Inches
61.02374
Cubic Foot
Cubic Cm
28,316.847
liter
Gallons (US)
0.26417205
Cubic Foot
Cubic Inch
1,728
liter
Milliliters
1,000
Cubic Foot
Gallon (US liq)
7.480519
liter/Minute
Gallon (US)/Hr
15.85032
Cubic Foot
liter
28.316847
Meter
Feet
3.2808399
Cubic Meter
Cubic Foot
35.31467
Meter
Inches
39.37007874
Cubic Meter
Cubic Inch
61,023.74
Micrometer
Millimeters
0.001
Cubic Meter
Gallon (US liq)
264.1721
Micrometer
Mils
0.03937008
Celsius (C)
Fahrenheit (F)
1.8
Micron
Micrometer
Fahrenheit (F)
Celsius (C)
0.5555556
Milligram/liter
Grains/Gal (US)
0.05841783
Foot
Centimeter
30.48
Parts/Million
Milligram/liter
Foot
Meter
0.3048
Pint (US liq)
Ounce (US liq)
16
Foot
Millimeter
304.8
Quart (US liq)
Ounce (US liq)
32
Foot of H20
Atmosphere
0.0294998
Rod
Feet
16.5
Foot of H20
bar
0.0298907
Square Foot
Square Inches
144
Foot of H20
Inch of Hg
0.882671
Square Mile
Acres
640
Gallon (US liq)
Cubic Feet
0.13368056
Square Yard
Feet
Gallon (US liq)
Cubic Inches
231
Tablespoon
Millimeter
14.79
Gallon (US liq)
Gallon (brit liq)
0.8326742
Teaspoon
Millimeter
4.93
Gallon (US liq)
liter
3.785412
Watt
bTU/Hour
3.41214
- 99 -
Table of elements
Sym
Ac
Al
Am
Sb
Ar
As
At
ba
bk
be
bi
b
br
Cd
Cs
Ca
Cf
C
Ce
Cl
Cr
Co
Cu
Cm
Dy
es
er
eu
Fm
F
Fr
Gd
Ga
Ge
Au
Hf
Num
89
13
95
51
18
33
85
56
97
4
83
5
35
48
55
20
98
6
58
17
24
27
29
96
66
99
68
63
100
9
87
64
31
32
79
72
Name
Helium
Holmium
Hydrogen
Indium
Iodine
Iridium
Iron
Krypton
lanthanum
lawrencium
lead
lithium
lutetium
Magnesium
Manganese
Mendelevium
Mercury
Molybdenum
Neodymium
Neon
Neptunium
Nickel
Niobium
Nitrogen
Nobelium
Osmium
Oxygen
Palladium
Phosphorus
Platinum
Plutonium
Polonium
Potassium
Praseodymium
Promethium
Protoactinium
Sym
He
Ho
H
In
I
Ir
Fe
Kr
la
lr
Pb
li
lu
Mg
Mn
Md
Hg
Mo
Nd
Ne
Np
Ni
Nb
N
No
Os
O
Pd
P
Pt
Pu
Po
K
Pr
Pm
Pa
Num
Name
Sym Num
2
Radium
Ra
88
67
Radon
Rn
86
1
Rhenium
Re
75
49
Rhodium
Rh
45
53
Rubidium
Rb
37
77
Ruthenium
Ru
44
26
Samarium
Sm
62
36
Scandium
Sc
21
57
Selenium
Se
34
103
Silicon
Si
13
82
Silver
Ag
47
3
Sodium
Na
11
71
Strontium
Sr
38
12
Sulfur
S
16
25
Tantalum
Ta
73
101
Technetium
Tc
43
80
Tellurium
Te
52
42
Terbium
Tb
65
60
Thallium
Tl
81
10
Thorium
Th
90
93
Thulium
Tm
69
28
Tin
Sn
50
41
Titanium
Ti
22
7
Tungsten
W
74
102
Unnihexium
Unh 106
76
Unnilpentium
Unp 105
8
Unnilquadium Unq 104
46
Unnilseptium
Uns 107
15
Uranium
U
92
78
Vanadium
V
23
94
Xenon
Xe
54
84
Ytterbium
Yb
70
19
Yttrium
Y
39
59
Zinc
Zn
30
61
Zirconium
Zr
40
91 Total Elements
107
TECHNICAL
Name
Actinium
Aluminum
Americium
Antimony
Argon
Arsenic
Astatine
barium
berkelium
berylium
bismuth
boron
bromine
Cadmium
Caesium
Calcium
Californium
Carbon
Cerium
Chlorine
Chromium
Cobalt
Copper
Curium
Dysprosium
einsteinium
erbium
europium
Fermium
Flourine
Francium
Gadolinium
Gallium
Germanium
Gold
Hafnium
- 100 -
Softening & Sodium

Probably the number one question arising during a discussion of water softening is that of the sodium issue. It is
greatly misunderstood due to all the bad press about too much salt (sodium) in the average Americans diet today.
Various studies contradict one another on the actual health-impact of sodium in the diet. We must have sodium to
live...but how much is enough...how much is too much? We will not attempt to answer those questions. However, we
can put the topic into perspective by showing where the sodium in ones life comes from daily.
The standard sodium ion exchange (softening) process uses sodium (salt) to exchange-out the hardness ions (calcium & magnesium). Therefore, when you remove the hardness ions, they are replaced with sodium ions. The amount
of sodium produced in the softening process is quite small and should not present any health problems for a healthy
person. As a matter of fact, the U.S. drinking water regulations have dropped sodium as a regulated component of
water. However, if a person has a question about whether or not they should consume water softened by the sodium
ion exchange process, they should consult with their own health professional.
The basic information below should put soft water sodium into perspective for you relative to sodium in foods. For
example, if you drank 3 quarts of water that was 10 grains hard before softening you would only take-in 223 milligrams of sodium or about 4.3% of the average daily intake of sodium attributable to the water. This would be less
than the amount of sodium contained in two slices of white bread.
TECHNICAL
FOOD
APPROXIMATE
SODIUM CONTENT
IN MILLIgRAMS
BREAKFAST
TABLE 1 - Sodium Added to Water from

Cation Exchange Softening
Initial Water
Sodium added by Cation exchange
Hardness
Softening of Water
Grains per Gallon Milligrams Na+/gal. Milligrams Na+/qt.
1/2 cup canned tomato juice

1 egg (no salt added)
2 slices bacon
2 biscuits or toast
2 teaspoons margarine
270
60
150
300
100
1
5
6
7
8
9
10
15
20
30
40
LUNCh
luncheon meat, corned beef

or ham (3 oz.)
Processed cheddar cheese (1 oz.)
2 slices white bread
1 cup milk
1 large olive
1 dill pickle
1 teaspoon mustard
Potato chips, about 10
DINNER
Steak, 6 oz., no salt added

Green salad with 1 ounce
French Dressing
baked potato, salt added
Two pats margarine
bread, 2 slices or equivalent
900
420
300
120
130
930
60
200
80
450
240
100
300
TOTAL SODIUM........5,110
(Milligrams)
30
149
179
209
239
269
298
447
596
894
1,191
7.5
37
44
52
60
68
75
112
150
225
300
TABLE 2 - Sodium Intake from Softened Water

Compared to Total Sodium Intake
Initial
Water
Hardness/
Grains per
Gallons
Milligrams
Na+ Per
3 qts.
Softened
Water
Milligrams
Na+ from
Food
Water
Total Na+
Consumed
Milligrams
% of Total
from
Softened
1
5
10
15
20
30
40
23
112
223
335
447
670
893
5,000
5,000
5,000
5,000
5,000
5,000
5,000
5,023
5,112
5,223
5,335
5,447
5,670
5,893
0.4%
2.2%
4.3%
6.5%
8.2%
12.5%
15.2%
- 101 -
Water Data & Useful Information
TECHNICAL
To convert pressure (in pounds per square feet) to Feet of Head pressure, use the following formula: FT = 2.31 x psi
One U.S. gallon of water contains 231 cu inches and weighs about 8.333 pounds.
A cubic foot of water contains about 7.50 gallons and weighs about 62.5 pounds.
To find the pressure in psi of a column of water, multiply the height of the column in feet by .434.
One pound of water occupies 27.70 cubic inches.
One cubic foot of salt water weighs about 64.33 pounds.
One standard barrel of water contains 31.50 gallons.
barrels per day (42 gallons) x .02917 = gallons per minute
Friction of liquids in piping increases as the square of the velocity.
Doubling the diameter of a pipe increases its capacity four times.
A miners inch of water is approximately equal to a supply of 12 gpm (9 in some states).
The gallons per minute which a pipe will deliver equals .0408 times the square of the diameter in inches, multiplied by
the velocity of water in feet per minute.
To find the capacity of a pipe or cylinder in gallons, multiply the square of the diameter in inches by the length in inches
then multiply by .0034.
The weight of water (in pounds) in any length pipe is obtained by multiplying the length in feet by the square of the
diameter in inches then multiply by .340.
One common water pail will hold 2.27 U.S. gallons or about 19 pounds of water.
Sharp angles or sudden bends in pipes cause an increase in friction and, consequently, more power is necessary.
Where change of direction is desired, it should be made with long, easy curves or by using 45 degree elbows
whenever possible.
About 80% of the earths surface is covered by water.
Around 97% of the earths water is contained in the oceans, 2% is in glaciers and icecaps; the remaining 1% is found in
other surface waters, groundwater and living tissue.
Rainfall in the U.S. ranges from about 7-130 inches per year depending on geography, averaging out to about 30 inches.
About 52% of our fresh water is used for industrial processes; 40% for irrigation, and 8% for all other uses.
Man can survive for about 30 days without food but only about 7 days without sufficient water.
The average human contains about 10 gallons of water or around 65% of bodyweight.
bone is about 20% water, the brain about 80%.
An average man needs about 2.50 gallons of water per day for proper health (from foods and beverages).
It is currently estimated that per capita consumption of water in the U.S. is 70-100 gallons per day for all uses.
Water boils at 212F (100C) and freezes at 32F (0C).
Most things contract when they freeze. Water, however, is one of the very few things that expands (by about 10%).
To find the circumference of a circle, multiply the diameter by 3.1416.
To find the circumference of a circle, multiply the radius by 6.283185.
To find the diameter of a circle, multiply the circumference by .31831.
To find the diameter of a circle, multiply the square root of the area by 1.12838.
To find the radius of a circle, multiply the square root of the area by 0.56419.
To find the area of a circle, multiply the square of the diameter by .7854.
To find the area of a circle, multiply the square of the circumference by 0.07958.
To find the surface of a sphere, multiply the square of the diameter by 3.1416.
To find the cubic inches in a sphere, multiply the cube of the diameter by .5236.
To find the U.S. gallon capacity of any size tank with given dimensions of the cylinder in inches, multiply the square of
the diameter by the length then multiply by .0034.
Steam rising from water at its boiling point has a pressure equal to the atmosphere (14.7 psi).
The expansion of water from its freezing point to boiling is 1 gallon in each 23 or approximately 4.333%.
SOURCE: Water Well Handbook, Keith Anderson, pp. 39 & 254, 1989
- 102 -
environmental Hotlines
listed below are a number of agencies that may be of assistance to you in the event you have questions or
need to report an emergency situation. Information was determined correct at the time of printing, however,
for the most up to date information check with the ePA online at www.epa.gov
AgENCY
ADDRESS / TELEPhONE
U.S. e.P.A. (Safe Drinking Water Hotline)
(800) 426-4791
TECHNICAL
For information on standards and contaminants
e.P.A. Region I (Me,MA, NH, VT, RI&CT)
1 Congress St.
boston, MA 02114-2023
(888) 372-7341
(617) 918-1111
e.P.A. Region II (NY, NJ, PR & VI)
290 broadway
212-637-5000
New York, NY 10007-1866
e.P.A. Region III (VA, WV, PA, De, MD &

DC)
1650 Arch Street (3PM52) (800) 438-2474

Philadelphia, PA 19103-2029 (215)814-5000
e.P.A. Region IV (Fl, GA, NC, SC, KY, TN, 61 Forsyth Street, SW
MS & Al)
Atlanta, GA 30303-3104
800-241-1754
(404) 562-9900
e.P.A. Region V (Il, IN, MI, MN, OH& WI)
77 W. Jackson blvd.
Chicago, Il 60604
312-353-2000
800-621-8431
e.P.A. Region VI (TX, NM, OK, AR &lA)
1445 Ross Avenue Suite 1200

Dallas, Texas 75202
(214) 665-6444
e.P.A. Region VII (Ne, KS, IA & MO)
901 N. 5th Street

Kansas City, KS 66101
e.P.A. Region VIII(MT, WY, UT, CO, ND &

SD)
e.P.A. Region IX (CA, NV, HI, AZ)
e.P.A. Region X (AK, WA, OR & ID)
RCRA Superfund Hotline
800-223-0425
303-312-6312
800-227-8917
(415) 947-8021
(866)-ePA-WeST
1200 Sixth Avenue
Seattle, WA 98101
(800) 424-4ePA
(206) 553-1200
(800) 424-9346
For general information on sites and hazardous waste laws
National Institute for Occupational Safety Health
(800) 35-NIOSH
For questions about workplace health hazards
National Response Center Hotline
(800)424-8802
To report release of a spill or oil or hazardous waste
Consumer Products Safety Commission
(800) 638-2772
To report products with actual or potential Hazards
National Pesticide Hotline

For information on health risks of pesticides
(800) 858-7378
- 103 -
Drinking Water Regulations

National Primary Drinking Water Regulations
National Primary Drinking Water Regulations (NPDWRs or primary standards) are legally
enforceable standards that apply to public water systems. Primary standards protect public
health by limiting levels of contaminants in drinking water.
National Secondary Drinking Water Regulations
National Secondary Drinking Water Regulations (NSDWRs or secondary standards) are nonenforceable guidelines regulating contaminants that may cause cosmetic effects (such as skin
or tooth discoloration) or aesthetic effects (such as taste, odor, or color) in drinking water.
ePA recommends secondary standards to water systems, but does not require systems to
comply. However, states may choose to adopt them as enforceable standards.
Definitions
Maximum Contaminant Level (MCL) -- The highest level of a contaminant that is

allowed in drinking water. MCls are set as close to MClGs as feasible using the best
available treatment technology and taking cost into consideration. MCls are
enforceable standards.
TECHNICAL
Maximum Contaminant Level goal (MCLg) --The level of a contaminant in drinking

water below which there is no known or expected risk to health. MClGs allow for a
margin of safety and are non-enforceable public health goals.
Maximum Residual Disinfectant Level goal (MRDLg) -- The level of drinking water
disinfectant below which there is no known or expected risk to health. MRDlGs do not
reflect the benefits of the use of disinfectants to control microbal contaminants.
Maximum Residual Disinfectant Level (MRDL) -- The highest level of a disinfectant
allowed in drinking water. There is convincing evidence that addition of a disinfectant
is necessary for control of microbal contaminants.
Treatment Technique (TT) -- A required process intended to reduce the level of a
contaminant in drinking water.
*Note: This document addresses the United States Environmental Protection Agency Drinking
Water Regulations in effect at its time of publication. These regulations are continually being
reviewed and updated at the federal level. If there is any question as to validity of the current
data, simply contact a state EPA office in your area.
- 104 -
Drinking Water Regulations
EPA National Primary Drinking Water Standards

MICROORgANISMS
Contaminant
TECHNICAL
Cryptosporidium
Potential health Effects from

Exposure above the MCL
MCL(mg/L)
Note: 1-1
Treatment Methods
Gastrointestinal illness (e.g., diarrhea,

vomiting, cramps)
Absolute 1 micron filtration, Ultraviolet

disinfection, Ozone, Chlorine disinfection

vomiting, cramps)
Absolute 1 micron filtration, Ultraviolet

disinfection, Ozone, Chlorine disinfection
Giardia lamblia
99% Removal/
inactivation
Heterotrophic plate count

(HPC)
No more than 500

baterial colonies
per mililiter
No health effects; it is an analytic method used

to measure a variety of bacteria that are
common in water. The lower the concentration
of bacteria in drinking water, the better
maintained the water system is.
Legionella
Note: 1-2
legionnaires Disease, a type of pneumonia
Total Coliforms (including

fecal coliform and e. coli)
Note: 1-3
Not a health threat in itself; it is used to

indicate whether other potentially harmful
bacteria may be present
Ultraviolet disinfection, ozone, hydrogen

peroxide or chlorine disinfection
Turbidity
Note: 1-4
Turbidity is a measure of the cloudiness of

water. It is used to indicate water quality and
filtration effectiveness (e.g., whether disease
-causing organisms are present). These
organisms can cause symptoms such as
nausea, cramps, diarrhea, and headaches.
Coagulation/Filtration,
Submicron Filtration, Ultrafiltration,
Reverse Osmosis, Cartridge Filtration
matched to Turbidity Particle size, or
Distillation
Viruses (enteric)
99% Removal
inactivation

vomiting, cramps)


same as above
Notes:
1-1. Cryptosporidium (as of 1/1/02 for systems serving more than 10,000 and 1/14/05 for systems serving less than 10,000) 99% removal.
1-2. Legionella: No limit, but ePA believes that if Giardia and viruses are removed/inactivated, Legionella will also be controlled.
1-3. Fecal coliform and e. coli are bacteria whose presence indicates that the water may be contaminated with human or animal wastes.
Disease-causing microbes (pathogens) in these wastes can cause diarrhea, cramps, nausea, headaches, or other symptoms. These
pathogens may pose a special health risk for infants, young children, and people with severely compromised immune systems. No
more than 5.0% total coliform-positive in a month. every sample that has total coliform must be anlayzed for either fecal coliforms or
E. coli if two consecutive TC-positive samples, and one is also positive for E. coli fecal coliforms, system has an acute MCl violation.
1-4. Turbidity: At no time can turbidity (cloudiness of water) go above 5 nephelolometric turbidity units (NTU); systems that filter must
ensure that the turbidity go no higher than 1 NTU (0.5) for conventional or direct filtration in at least 95% of the daily samples in any
month. As of January 1, 2002, for systems servicing more than 10,000, and January 14, 2005, for systems servicing less than
10,000, turbidity may never exceed 1 NTU, and must not exceed 0.3 NTU in 95% of daily samples in any month.
RADIONUCLIDES
Contaminant
Alpha particles
beta particles & photon
emitters
Radium 226 & Radium
228 (combined)
Uranium
MCL(mg/L)
15 picocuries per liter
(pCi/l)
4 millirems
per year
5 pCi/l
30 ug/l as of
12/08/03

Treatment Methods
Increased Risk of Cancer
Ion exchange, Reverse Osmosis,

Distallation, & electrodialysis
Ion exchange, Reverse Osmosis,

Cation exchange, Reverse Osmosis,

Increased Risk of Cancer, kidney toxicity
Coagulation/Filtration, Submicron
Filtration, Anion exchange, Activated
Alumina, Reverse Osmosis,
Distillation, and electrodialysis
- 105 -
Inorganic Chemicals
Contaminant
Antimony
Arsenic
Asbestos (Fibers > 10

micrometers)
barium
beryllium
Cadmium
Chromium (total)

Treatment Methods
0.006
Increase in blood cholesterol; decrease in

blood sugar
Filtration, Reverse Osmosis,
Ultrafiltration, and Distillation
0.010 as of
1/23/06
Skin damage or problems with circulatory

systems, and may have increased risk of
getting cancer
Coagulation/Filtration, Submicron Filtration,

Anion exchange, Activated Alumina,
Reverse Osmosis, Distillation, electrodialysis, and granular ferric oxide media filt.
Increased Risk of developing benign intestinal

polyps
Filtration, Reverse Osmosis,
Ultrafiltration, and Distillation
Increase in blood pressure
Cation exchange, Reverse Osmosis

Intestinal lesions
Filtration/Activated Carbon, Activated
Alumina, Cation exchange, Reverse
Osmosis, Distillation, and
electrodialysis
Kidney Damage
Filtration, Cation exchange,Reverse
electrodialysis
Allergic dermatitis
Coagulation/Filtration, Cation
exchange, Reverse Osmosis,
Distillation, Anion exchange, and
electrodialysis
Short term exposure: Gastrointestinal distress.

long term exposure: liver or kidney damage.
Cation exchange (20%-90%),

Reverse Osmosis, Distillation, and
electrodialysis
7 million fibers
per liter (MFl)
2
0.004
0.005
0.1
Note: 2-1
1.3 action level
Cyanide (as free cyanide)
0.2
Nerve damage or thyroid problems
Chemical Oxidation/Disinfection at
pH > 10, Anion exchange, Reverse
electrodialysis
Flouride
4.0
bone disease (pain and tenderness of the

bones); Children may get mottled teeth
Activated Alumina, Activated Carbon,

Reverse Osmosis, Distillation, and
electrodialysis
Infants and Children: Delays in physical or

mental development; children could show
slight deficits in attention span and learning
abilities; Adults: Kidney problems, high blood
pressure

Filtration/Activated Carbon, Reverse
electrodialysis
Kidney damage
Submicron Filtration/Activated Carbon,

Reverse Osmosis, Distillation, Anion
exchange, and electrodialysis
Infants below the age of six months who drink

water containing nitrate or nitrite in excess of
the MCl could become seriously ill and, if
untreated, may die. Symptoms include
shortness of breath and blue-baby syndrome.
Anion exchange, Reverse Osmosis,

Distillation, and electroradialysis
lead
Mercury (inorganic)
Nitrate (measured as Nitrogen)

Nitrite (measured as Nitrogen)
Note: 2-1
0.015 action level
0.002
10
1
TECHNICAL
Copper
MCL(mg/L)
Chemical Oxidation/Disinfection,
Anion exchange, Reverse Osmosis,
Selenium
0.05
Hair or fingernail loss; numbness of fingers or

toes; circulatory problems
Filtration/Activated Carbon, Activated
Alumina, Anion exchange, Reverse
electrodialysis
Thallium
0.002
Hair loss; changes in blood; kidney, intestine

or liver problems
Cation exchange, Activated Alumina,

and Distillation
Note:
2-1. lead and Copper are regulated by a treatment technique that requires systems to control the corrosiveness of their water. If more than 10% of
tap water samples exceed action level, water systems must take additional steps.
- 106 -
Organic Chemicals
Contaminant
Acrylamide
Note: 3-1

Treatment Methods
Nervous systems or blood problems
Control of water treatment chemicals

and surfaces in contact with water
Alachlor
0.002
eye, liver, kidney or spleen problems; anemia;

increased risk of cancer
Activated Carbon, Aeration
Atrazine
0.003
Cardiovascular system or reproductive

problems
Activated Carbon
benzene
0.005
Anemia; decrease in blood platelets;

0.0002
Reproductive difficulties; increased risk of

cancer
Activated Carbon
0.04
Problems with blood, nervous system, or

reproductive system
Activated Carbon
Carbon tetrachloride
0.005
liver problems; increased risk of cancer
Chlordane
0.002
liver or nervous system problems; increased

risk of cancer
Activated Carbon
liver or kidney problems
Activated Carbon
Kidney, liver, or adrenal gland problems
Activated Carbon
Minor kidney changes
Activated Carbon

cancer
Activated Carbon
liver, kidney, or circulatory system problems
benzo(a)pyrene (PAHs)
Carbofuran
Chlorobenzene
2,4-D
Dalapon
TECHNICAL
MCL(mg/L)
1,2-Dibromo-3-chloropropane
(DbCP)
0.1
0.07
0.2
0.0002
o-Dichlorobenzene
0.6
p-Dichlorobenzene
0.075
Anemia; liver, kidney or spleen damage;

changes in blood
1,2-Dichloroethane
0.005
Increased risk of cancer
1,1-Dichloroethylene
0.007
liver problems
0.07
liver problems
0.1
liver problems
cis-1,2-Dichloroethylene
trans-1,2-Dichloroethylene
Dichloromethane
0.005
Aeration
1,2-Dichloropropane
0.005
0.4
Weight loss, liver problems, or possible

reproductive difficulties
Di(2-ethylhexyl) phthalate
0.006
Reproductive difficulties; liver problems;

Activated Carbon
Dinoseb
0.007
Reproductive difficulties
Activated Carbon

cancer
Activated Carbon
Cataracts
Activated Carbon
Stomach and intestinal problems
Activated Carbon
liver problems
Activated Carbon
Increased cancer risk, and over a long period

of time, stomach problems
Control of water treatment chemicals

and surfaces in contact with water
Di(2-ethylhexyl) adipate
Dioxin (2,3,7,8-TCDD)
Diquat
endothall
endrin
epichlorohydrin
0.00000003
0.02
0.1
0.002
Note: 3-1
Note:
3-1. each water system must certify, in writing, to the state (using third-party or manufacturers certification) that when it uses acrylamide and/or
epichlorohydrin to treat water, the combination (or product) of dose and monomer level does not exceed the levels specified as follows:
Acrylamide = 0.05% dosed at 1 mg/l (or equivalent); epichlorohydrin = 0.01% dosed at 20 mg/l (or equivalent).
- 107 -
Organic Chemicals Continued
Contaminant
ethylbenzene
ethylene dibromide
MCL(mg/L)
0.7
0.00005

Treatment Methods
Problems with liver, stomach, reproductive

system, or kidneys; increased risk of cancer
Kidney problems; reproductive difficulties
Activated Carbon
0.7
Heptachlor
0.0004
liver damage; increased risk of cancer
Activated Carbon
Heptachlor epoxide
0.0002
liver damage; increased risk of cancer
Activated Carbon
Hexachlorobenzene
0.001
liver or kidney problems; reproductive

difficulties; increased risk of cancer
Activated Carbon
Kidney or stomach problems
0.0002
Activated Carbon
0.04
Reproductive difficulties
Activated Carbon
Slight nervous system effects
Activated Carbon
liver or kidney problems; increased cancer

risk
Activated Carbon
liver problems
Activated Carbon
Hexachlorocyclopentadiene
lindane
Methoxychlor
Oxamyl (Vydate)
Pentachlorophenol
Picloram
0.05
0.2
0.001
0.5
Polychlorinated biphenyls
(PCbs)
0.0005
Skin changes; thymus gland problems;

immune deficiencies; reproductive or nervous
system difficulties; increased risk of cancer
Activated Carbon
Simazine
0.004
Problems with blood
Activated Carbon
liver, kidney, or circulatory system problems
liver problems, increased risk of cancer
Nervous system, kidney, or liver problems
Kidney, liver, or thyroid problems; increased

risk of cancer
Activated Carbon
Styrene
Tetrachloroethylene
Toluene
Toxaphene
0.1
0.005
1
0.003
2,4,5-TP (Silvex)
0.05
liver problems
Activated Carbon
1,2,4-Trichlorobenzene
0.07
Changes in adrenal glands
liver, nervous system, or circulatory problems
1,1,1-Trichloroethane
0.2
1,1,2-Trichloroethane
0.005
liver, kidney, or immune system problems
Trichloroethylene
0.005
Vinyl Chloride
0.002
Aeration
Xylenes (total)
10
Nervous system damage
TECHNICAL
Glyphosate
- 108 -
Disinfectants / byproducts
DISINFECTANT
Contaminant
MCL(mg/L)
Chloramines (as Cl2)
MRDl = 4.0

Treatment Methods
eye/nose irritation; stomach discomfort,

anemia
Activated Carbon
Chlorine (as Cl2)
MRDl = 4.0
eye/nose irritation; stomach discomfort
Activated Carbon
Chlorine Dioxide (as ClO2)
MRDl = 0.8
Anemia; infants & young children, nervous

system effects
Activated Carbon
DISINFECTANT BYPRODUCT
TECHNICAL
Contaminant
MCL(mg/L)
bromate
0.010
Chlorite

Treatment Methods
Call ePA for more info.
Anemia; infants & young children, nervous

system effects
Haloacetic acids (HAA5)
0.060
Total Trihalomethanes (TTHMs)
0.080
liver, kidney or central nervous system

problems; increased risk of cancer
Activated Carbon
- 109 -
Secondary Contaminants
EPA National Secondary Drinking Water Standards

Contaminant
Secondary
Standard
Aluminum
0.05 to 0.2 mg/l
Chloride
Color
Copper
Corrosivity
Fluoride
250 mg/l
15 (color units)
Note: 1
1.0 mg/l
Non-corrosive
2.0
Treatment Methods
Cation exchange, Reverse Osmosis, Distillation, electrodialysis
Reverse Osmosis, Distillation, Anion exchange, electrodialysis
Anion exchange, Reverse Osmosis, Activated, Carbon, Distillation, Filtration, Ozonation,
Chloronation, Activated Alumina
Reverse Osmosis, Distillation, Cation exchange (20%-90%), electrodialysis
Calcite or Calcite/Magnesium Oxide (Magnesia), (5 to 1) Filter to raise pH, Soda Ash
Chemical Feed, Sodium Silicate Feed, Reduce TDS via Reverse Osmosis (partial, split
stream treatment), Coatings, Insulating Unions
Activated Alumina, Activated Carbon, Reverse Osmosis, Distillation
0.5 mg/l
Chlorination, Reverse Osmosis, Activated Carbon, Distillation, Ozonation
Iron
0.3 mg/l
Note: 2
Filtration (oxidizing filters), Cation exchange, Reverse Osmosis, Pressure

Areation/Filtration, Chlorination - Precipitation/Filtration, Distillation, electrodialysis
Manganese
Odor
0.05 mg/l
Note: 3
3 threshold odor #
Note: 4
Filtration (oxidizing filters), Cation exchange, Reverse Osmosis, Distillation,

Chlorination - Precipitation/Filtration, Pressure Areation/Filtration, electrodialysis
Activated Carbon, Aeration, Oxidation
pH
6.5 - 8.5
pH may be increased by alkalies and may be decreased by acids, Ion exchange,

Neutralizing Filter (Calcite, Magnesia)
Silver
0.10 mg/l
Coagulation/Filtration, Submicron Filtration/Activated Carbon, Ion exchange (Anion or

Cation depending on complexed Ion Species)
Sulfate
250 mg/l
Reverse Osmosis, Distillation, Anion exchange, electrodialysis
Total Dissolved Solids (TDS)
500 mg/l
Reverse Osmosis, Distillation, Deionzation by Ion exchange (Cation/Anion in two bed

or mixed bed), electrodialysis
Zinc
5 mg/l
TECHNICAL
Foaming Agents
Reverse Osmosis, Distillation, Cation exchange, electrodialysis
Notes:
1. Color -
Color units are based on the APHA recommended standard of 1 color unit being equal to 1 mg/l of
platinum or chloroplatinate ion.
2. Iron Ferrous Iron (clear water iron) is readily converted to ferric iron (red water iron) in the presence of
any air or oxidizing material; precipitating ferric iron must be prevented to avoid fouling and
interference with effective reverse osmosis membrane rejection.
3. Manganese - Manganese must be maintained in the soluble manganous (Mn + 2) stated to avoid fouling and
interference with effective reverse osmosis membrane rejection.
4. Odor Chlorine and hydrogen sulfide are examples of odors that may be reduced by the treatment
methods suggested
- 110 -
- NOTeS -
- 111 -
Parts
PARTS
- 112 -
Valve Part Numbers - Signature Series Valve

Complete Control Valve Part No.
w / Plastic
w / Plastic
bypass & 3/4 bypass & 1
Stainless Steel Stainless Steel
Yoke
Yoke
20001X461
20001X462
20001X463
20001X464
20001X521
20001X466
20001X467
20001X468
20001X469
20001X531
Without
bypass or
Yoke
20001X471
20001X472
20001X473
20001X474
20001X541
w / Plastic
w / Plastic
w / Stainless
bypass & yoke bypass & yoke Steel bypass
3/4
1
3/4
20001X481
20001X482
20001X483
20001X484
20001X551
20001X486
20001X487
20001X488
20001X489
20001X561
20001X491
20001X492
20001X493
20001X494
20001X571
w / Stainless
Steel bypass
1
Drain
line
Flow
cntrl
20001X496
20001X497
20001X498
20001X499
20001X581
1.5
2.0
2.4
3.0
1.5
20001X522 20001X532 20001X542 20001X552 20001X562 20001X572 20001X582 2.0
PARTS
20001X523 20001X533 20001X543 20001X553 20001X563 20001X573 20001X583 2.4

20001X524
20001X526
20001X527
20001X528
20001X529
20001X530
20002X521
20002X523
20002X524
20002X525
20003X461
20003X462
20003X463
20003X464
20003X520
20003X521
20003X522
20003X523
20001X534
20001X536
20001X537
20001X538
20001X539
20001X540
20002X531
20002X533
20002X534
20002X535
20003X466
20003X467
20003X468
20003X469
20003X530
20003X531
20003X532
20003X533
20001X544
20001X546
20001X547
20001X548
20001X549
20001X550
20002X541
20002X543
20002X544
20002X545
20003X471
20003X472
20003X473
20003X474
20003X540
20003X541
20003X542
20003X543
20001X554
20001X556
20001X557
20001X558
20001X559
20001X560
20002X551
20002X553
20002X554
20002X555
20003X481
20003X482
20003X483
20003X484
20003X550
20003X551
20003X552
20003X553
20001X564
20001X566
20001X567
20001X568
20001X569
20001X570
20002X561
20002X563
20002X564
20002X565
20003X486
20003X487
20003X488
20003X489
20003X560
20003X561
20003X562
20003X563
20001X574
20001X576
20001X577
20001X578
20001X579
20001X580
20002X571
20002X573
20002X574
20002X575
20003X491
20003X492
20003X493
20003X494
20003X570
20003X571
20003X572
20003X573
20001X584
20001X586
20001X587
20001X588
20001X589
20001X590
20002X581
20002X583
20002X584
20002X585
20003X496
20003X497
20003X498
20003X499
20003X580
20003X581
20003X582
20003X583
3.0
4.0
5.0
5.0
1.2
7.0
5.0
7.0
10.0
15.0
1.5
2.0
2.4
3.0
1.2
1.5
2.0
2.4
20003X524
20003X526
20003X527
20003X528
20005X521
20003X534
20003X536
20003X537
20003X538
20005X531
20003X544
20003X546
20003X547
20003X548
20005X541
20003X554
20003X556
20003X557
20003X558
20005X551
20003X564
20003X566
20003X567
20003X568
20005X561
20003X574
20003X576
20003X577
20003X578
20005X571
20003X584
20003X586
20003X587
20003X588
20005X581
3.0
4.0
5.0
7.0
5.0
20005X523 20005X533 20005X543 20005X553 20005X563 20005X573 20005X583 7.0
Model Number Used On
CT24(V)
CT24T
CT32(V)
CT32T
TS24(V), TSI48,
TST48
TS24T, TS32(V),
TN25
TS32T, TS48(V),
TSI64, TST64
TS48T, TSI96
TS64(V)
TS64T, TS96(V)
IF10, IF15
TN15, TST32, TSI32
IF25, TS128(V)
WF10, WF15
WF25
WF30
WF40
CM24(V)
CM24T
CM32(V)
CM32T
MN15, MST32, MSI32
MS24(V), MST48, MSI48
MS24T, MS32(V)
MS32T, MS48(V),
MST64, MSI64
MS48T, MSI96
MS64(V)
MS96(V), MS64T
MS128(V)
RF10(VS), RF15(VS),
UT10, UT15, UTP15
RF25(VS), UT25,
UTP25
20005X524 20005X534 20005X544 20005X554 20005X564 20005X574 20005X584 10.0 RF30(VS), UT30, UTP30
20005X525 20005X535 20005X545 20005X555 20005X565 20005X575 20005X585 15.0 UT40, UTP40
- 113 -
Valve Part Numbers - 2510 Valve

w / Plastic
bypass & 3/4
Nickel Plate
Yoke
w / Plastic
bypass & 1
Nickel Plate
Yoke
Without
bypass or
Yoke
20251X461
20251X462
20251X463
20251X464
20251X521
20251X522
20251X466
20251X467
20251X468
20251X469
20251X531
20251X532
20251X471
20251X472
20251X473
20251X474
20251X541
20251X542
w / Plastic
w / Plastic
w / Nickel
w / Nickel
Drain
bypass & yoke bypass & yoke Plated bypass Plated bypass line
3/4
1
3/4
1
Flow
cntrl
20251X481
20251X482
20251X483
20251X484
20251X551
20251X552
20251X486
20251X487
20251X488
20251X489
20251X561
20251X562
20251X491
20251X492
20251X493
20251X494
20251X571
20251X572
20251X496
20251X497
20251X498
20251X499
20251X581
20251X582
1.5
2.0
2.4
3.0
1.5
2.0
20251X523 20251X533 20251X543 20251X553 20251X563 20251X573 20251X583 2.4

20251X524
20251X526
20251X527
20251X528
20251X529
20251X530
20252X521
20252X523
20252X524
20253X461
20253X462
20253X463
20253X464
20253X520
20253X521
20251X534
20251X536
20251X537
20251X538
20251X539
20251X540
20252X531
20252X533
20252X534
20253X466
20253X467
20253X468
20253X469
20253X530
20253X531
20251X544
20251X546
20251X547
20251X548
20251X549
20251X550
20252X541
20252X543
20252X544
20253X471
20253X472
20253X473
20253X474
20253X540
20253X541
20251X554
20251X556
20251X557
20251X558
20251X559
20251X560
20252X551
20252X553
20252X554
20253X481
20253X482
20253X483
20253X484
20253X550
20253X551
20251X564
20251X566
20251X567
20251X568
20251X569
20251X570
20252X561
20252X563
20252X564
20253X486
20253X487
20253X488
20253X489
20253X560
20253X561
20251X574
20251X576
20251X577
20251X578
20251X579
20251X580
20252X571
20252X573
20252X574
20253X491
20253X492
20253X493
20253X494
20253X570
20253X571
20251X584
20251X586
20251X587
20251X588
20251X589
20251X590
20252X581
20252X583
20252X584
20253X496
20253X497
20253X498
20253X499
20253X580
20253X581
3.0
4.0
5.0
5.0
1.2
7.0
5.0
7.0
10.0
1.5
2.0
2.4
3.0
1.2
1.5
20253X524
20253X526
20253X527
20255X521
20253X534
20253X536
20253X537
20255X531
20253X544
20253X546
20253X547
20255X541
20253X554
20253X556
20253X557
20255X551
20253X564
20253X566
20253X567
20255X561
20253X574
20253X576
20253X577
20255X571
20253X584
20253X586
20253X587
20255X581
3.0
4.0
5.0
5.0
20255X523 20255X533 20255X543 20255X553 20255X562 20255X573 20255X583 7.0

20255X524 20255X534 20255X544 20255X554 20255X563 20255X574 20255X584 10.0
CT24(V)
CT24T
CT32(V)
CT32T
TS24(V), TSI48, TST48
TS24T, TS32(V),
TST48, TN15
TS32T, TS48(V), TSI64,
TST64, TN25
TS48T
TS64(V)
TS96(V), TS64T
IF10, IF15
TN15, TST32, TSI32
IF25, TS128(V)
WF10 WF15
WF25
WF30
CM24(V)
CM24T
CM32(V)
CM32T
MN15, MSI32, MST32
MS24(V), MST48,
MSI48
MS24T, MS32, MSI64
MS32T, MS48(V),
MSI64, MST64, MN25
MS48T, MSI96
MS64(V)
MS96(V), MS64T
RF10, RF15, UT10
UT15, UTP15
RF25, UT25, UTP25
RF30, UT30, UTP30
PARTS
20253X522 20253X532 20253X542 20253X552 20253X562 20253X572 20253X582 2.0

20253X523 20253X533 20253X543 20253X553 20253X563 20253X573 20253X583 2.4
- 114 -
Valve Part Numbers - 5600 Valve

w / Plastic
bypass & 3/4
Nickel Plate
Yoke
w / Plastic
bypass & 1
Nickel Plate
Yoke
Without
bypass or
Yoke
20561X461
20561X462
20561X463
20561X464
20561X501
20561X502
20561X466
20561X467
20561X468
20561X469
20561X511
20561X512
20561X471
20561X472
20561X473
20561X474
20561X521
20561X522
w / Plastic
w / Plastic
w / Nickel
w / Nickel
Drain
3/4
1
3/4
1
Flow
cntrl
20561X481
20561X482
20561X483
20561X484
20561X531
20561X532
20561X486
20561X487
20561X488
20561X489
20561X541
20561X542
20561X491
20561X492
20561X493
20561X494
20561X551
20561X552
20561X496
20561X497
20561X498
20561X499
20561X561
20561X562
1.5
2.0
2.4
3.0
1.5
2.0
PARTS
20561X503 20561X513 20561X523 20561X533 20561X543 20561X553 20561X563 2.4

20561X504
20561X506
20561X507
20561X500
20563X461
20563X462
20563X463
20563X464
20563X501
20563X502
20563X503
20563X504
20563X506
20563X507
20563X500
20563X501
20563X503
20561X514
20561X516
20561X517
20561X510
20563X466
20563X467
20563X468
20563X469
20563X511
20563X512
20563X513
20563X514
20563X516
20563X517
20563X510
20563X511
20563X513
20561X524
20561X526
20561X527
20561X520
20563X471
20563X472
20563X473
20563X474
20563X521
20563X522
20563X523
20563X524
20563X526
20563X527
20563X520
20563X521
20563X523
20561X534
20561X536
20561X537
20561X530
20563X481
20563X482
20563X483
20563X484
20563X531
20563X532
20563X533
20563X534
20563X536
20563X537
20563X530
20563X531
20563X533
20561X544
20561X546
20561X547
20561X540
20563X486
20563X487
20563X488
20563X489
20563X541
20563X542
20563X543
20563X544
20563X546
20563X547
20563X540
20563X541
20563X543
20561X554
20561X556
20561X557
20561X550
20563X491
20563X492
20563X493
20563X494
20563X551
20563X552
20563X553
20563X554
20563X556
20563X557
20563X550
20563X551
20563X553
20561X564
20561X566
20561X567
20561X560
20563X496
20563X497
20563X498
20563X499
20563X561
20563X562
20563X563
20563X564
20563X566
20563X567
20563X560
20563X561
20563X563
3.0
4.0
5.0
1.2
1.5
2.0
2.4
3.0
1.5
2.0
2.4
3.0
4.0
5.0
1.2
1.5
2.4
CT24(V)
CT24T
CT32(V)
CT32T
TS24(V), TSI32, TST32
TST48, TN15
TST64, TN25
TS48T
TS64(V)
TS96
TSI32, TST32, TN15
CM24(V)
CM24T
CM32(V), MN25
CM32T
MS24(V)
MS24T, MS32(V)
MS32T, MS48(V)
MS48T
MS64(V)
MS96(V), MS64T
MSI32, MST32, MN15
MSI48, MST48
MSI64, MST64, MN25
- 115 -
Valve Part Numbers - SXT Valve

w / Plastic
bypass & 3/4
Nickel Plate
Yoke
w / Plastic
bypass & 1
Nickel Plate
Yoke
20564X461
20564X462
20564X463
20564X464
20564X501
20564X502
20564X503
20564X504
20564X506
20564X507
20564X500
20564X501
20564X503
20564X466
20564X467
20564X468
20564X469
20564X511
20564X512
20564X513
20564X514
20564X516
20564X517
20564X510
20564X511
20564X513
Without
bypass or
Yoke
20564X471
20564X472
20564X473
20564X474
20564X521
20564X522
20564X523
20564X524
20564X526
20564X527
20564X520
20564X521
20564X523
w / Plastic
w / Plastic
w / Nickel
w / Nickel
Drain
3/4
1
3/4
1
Flow
cntrl
20564X481
20564X482
20564X483
20564X484
20564X531
20564X532
20564X533
20564X534
20564X536
20564X537
20564X530
20564X531
20564X533
CM24(V)
CM24T
CM32(V)
CM32T
MS24(V)
MS24T, MS32(V)
MS32T, MS48
MS48T
MS64(V)
MS96(V), MS64T
MSI32, MST32, MN15
MSI48, MST48
MSI64, MST64, MN25
20564X486
20564X487
20564X488
20564X489
20564X541
20564X542
20564X543
20564X544
20564X546
20564X547
20564X540
20564X541
20564X543
20564X491
20564X492
20564X493
20564X494
20564X551
20564X552
20564X553
20564X554
20564X556
20564X557
20564X550
20564X551
20564X553
20564X496
20564X497
20564X498
20564X499
20564X561
20564X562
20564X563
20564X564
20564X566
20564X567
20564X560
20564X561
20564X563
1.5
2.0
2.4
3.0
1.5
2.0
2.4
3.0
4.0
5.0
1.2
1.5
2.4
PARTS
- 116 -
PARTS
Parts Diagram - CT & CM Series Softeners
ReF.
NO.
PART
NO.
1
2
3
4
5
6
7
8
40450X100
40450X101
40450X102
40450X103
40450X105
40450X104
-------
9
10
11
12
13
14
15
------40330X105
40330X107
40330X104
40330X106
40330X103
DeSCRIPTION
CAbINeT, lID & COVeR ASSeMblY
CAbINeT ONlY
lID ONlY
COVeR ONlY
GRID PlATe 10" TANK
GRID PlATe 8" TANK
ReSIN TANK See CHART NeXT PAGe
DISTRIbUTOR & TUbe ASSY.
See CHART NeXT PAGe
CATION ReSIN See CHART NeXT PAGe
CONTROl VAlVe See CHART NeXT PAGe
bRINe Well
SAFeTY bRINe & FlOAT ASSY.
4" bRINe Well CAP
OVeRFlOW FITTING & NUT
bRINe TUbING - 3/8" OD X 48" lG
- 117 -
Parts list - CT & CM Series Softeners
CT Series Softeners
ReF.
NO.
7
DeSCRIPTION
CT24(V)
CT24T
CT32(V)
CT32T
ReSIN TANK
8
9
10
PART NO.
30835X100 30835X100 31035X100 31035X100
SIZe
8" X 35"
8" X 35"
10" X 35"
10 X 35"
VORTeCH TANK
PART NO.
30935V100
NA
31035V100
NA
SIZe
9" X 35"
10" X 35"
330035X11
N/A
330035X11
N/A
TURbUlATOR & TUbe ASSY.
N/A
340035X11
N/A
340035X11
CATION ReSIN
(1) SR75
(1) SR75
(1) SR10
(1) SR10
SR75 3/4 CU. FT.
SR10 1 CU. FT.
CONTROl VAlVe W/ DlFC
1.5
2.0
2.4
3.0
SIGNATURe VAlVe W/ bYPASS & S.S. YOKe 3/4"
20001X461 20001X462 20001X463 20001X464
SIGNATURe VAlVe W/ bYPASS & S.S. YOKe 1"
20001X466 20001X467 20001X468 20001X469
SIGNATURe VAlVe W/O bYPASS & YOKe
20001X471 20001X472 20001X473 20001X474
SIGNATURe VAlVe W/ bYPASS & 1" YOKe
20001X481 20001X482 20001X483 20001X484
SIGNATURe VAlVe W/ PlASTIC bYPASS & YOKe 3/4"
20001X486 20001X487 20001X488 20001X489
SIGNATURe VAlVe W/ STAINleSS STeel bYPASS 3/4" 20001X491 20001X492 20001X493 20001X494
SIGNATURe VAlVe W/ STAINleSS STeel bYPASS 1"
20001X496 20001X497 20001X498 20001X499
CM Series Softeners
ReF.
DeSCRIPTION
NO
7 ReSIN TANK
10
CM24T
CM32(V)
CM32T
PART NO.
30835X100 30835X100 31035X100 31035X100
SIZe
8" X 35"
8" X 35"
10" X 35"
10 X 35"
VORTeCH TANK
PART NO.
30935V100
NA
31035V100
NA
SIZe
9" X 35"
10" X 35"
330035X11
N/A
330035X11
N/A
N/A
340035X11
N/A
340035X11
CATION ReSIN
(1) SR75
(1) SR75
(1) SR10
(1) SR10
SR75 3/4 CU. FT.
SR10 1 CU. FT.
1.5
2.0
2.4
3.0
SIGNATURe VAlVe W/ bYPASS & S.S. YOKe 3/4"
20003X461 20003X462 20003X463 20003X464
SIGNATURe VAlVe W/ bYPASS & S.S. YOKe 1"
20003X466 20003X467 20003X468 20003X469
SIGNATURe VAlVe W/O bYPASS & YOKe
20003X471 20003X472 20003X473 20003X474
SIGNATURe VAlVe W/ bYPASS & 1" YOKe
20003X481 20003X482 20003X483 20003X484
SIGNATURe VAlVe W/ PlASTIC bYPASS & YOKe 3/4"
20003X486 20003X487 20003X488 20003X489
SIGNATURe VAlVe W/ STAINleSS STeel bYPASS 3/4" 20003X491 20003X492 20003X493 20003X494
SIGNATURe VAlVe W/ STAINleSS STeel bYPASS 1"
20003X496 20003X497 20003X498 20003X499
PARTS
CM24(V)
- 118 -
Parts Diagram - TS Series Softeners
DeSCRIPTION
ReF
NO.
2
3
PARTS
4
5
TS24(V)
TS24T
TS32(V)
TS32T
TS48(V)
TS48T
TS64(V)
TS64T
TS96V
TS128V
ReSIN TANK PART NO. 30844X100 30844X100 30948X100 30948X100 31054X100 31054X100 31348X100 31348X100 31465X100 31665X100
W/ bASe
SIZe
8" X 44"
8" X 44" 9" X 48" 9" X 48" 10" X 54" 10" X 54" 13" X 48" 13" X 48" 14" X 65" 16 X 65
VORTeCH TANK PART NO. 30942V100
NA
30948V100
NA
31054V100
NA
31348V100
NA
31465V100 31665V100
W/ bASe
SIZe
9" X 42"
9" X 48"
10" X 54"
13" X 48"
14" X 65" 16" X 65"
DISTRIbUTOR & TUbe ASSY. 330044X11
N/A
330048X11
N/A
330054X11
N/A
330048X11
N/A
330065X11 330065X11
N/A
340044X11
N/A
340048X11
N/A
340054X11
N/A
340048X11
N/A
N/A
CATION ReSIN
(1) SR75 (1) SR75 (1) SR10 (1) SR10 (2) SR75 (2) SR75 (2) SR10 (2) SR10 (3) SR10
(4) SR10
SR75 = 3/4 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
50 lbS. 70 lbS.
1.5
2.0
2.0
2.4
2.4
3.0
4.0
5.0
5.0
7.0
SIGNATURe VAlVe
20001X521 20001X522 20001X522 20001X523 20001X523 20001X524 20001X525 20001X526 20001X527 CONSUlT
W/ PlASTIC bYPASS
FACTORY
& 3/4" S.S. YOKe
SIGNATURe VAlVe
20001X531 20001X532 20001X532 20001X533 20001X533 20001X534 20001X535 20001X536 20001X537
W/ PlASTIC bYPASS
& 1" S.S. YOKe
SIGNATURe VAlVe
20001X541 20001X542 20001X542 20001X543 20001X543 20001X544 20001X545 20001X547 20001X548
W/O bYPASS & YOKe
SIGNATURe VAlVe
20001X551 20001X552 20001X552 20001X553 20001X553 20001X554 20001X555 20001X556 20001X557
W/ bYPASS & 3/4"
YOKe
SIGNATURe VAlVe
20001X561 20001X562 20001X562 20001X563 20001X563 20001X564 20001X565 20001X566 20001X567
W/ PlASTIC bYPASS
& 1" YOKe
SIGNATURe VAlVe
20001X57120001X572 20001X572 20001X573 20001X573 20001X574 20001X575 20001X576 20001X577
W/ STAINleSS STeel
bYPASS 3/4"
SIGNATURe VAlVe
20001X581 20001X582 20001X582 20001X583 20001X583 20001X584 20001X585 20001X586 20001X587
W/ STAINleSS STeel
bYPASS 1"
40440X000 40500X000
40330X000
bRINe TANK ASSeMblY
18 X 33
18 X 40 24 X 50
- 119 -
Parts Diagram - MS Series Softeners
ReF
NO.
2
3
4
5
MS24(V)
MS24T
MS32(V)
MS32T
MS48(V)
MS48T
MS64(V)
MS64T
MS96V
MS128V
ReSIN TANK PART NO. 30844X100 30844X100 30948X100 30948X100 31054X100 31054X100 31348X100 31348X100 31465X100 31665X100
W/ bASe
SIZe
8" X 44"
8" X 44" 9" X 48" 9" X 48" 10" X 54" 10" X 54" 13" X 48" 13" X 48" 14" X 65" 16 X 65
NA
30948V100
NA
31054V100
NA
31348V100
NA
31465X100 31665X100
W/ bASe
SIZe
9" X 42"
9" X 48"
10" X 54"
13" X 48"
14" X 65" 16" X 65"
DISTRIbUTOR & TUbe ASSY. 330044X11
N/A
330048X11
N/A
330054X11
N/A
330048X11
N/A
330065X11 330065X11
N/A
340044X11
N/A
340048X11
N/A
340054X11
N/A
340048X11
N/A
N/A
CATION ReSIN
(1) SR75 (1) SR75 (1) SR10 (1) SR10 (2) SR75 (2) SR75 (2) SR10 (2) SR10 (3) SR10 (4) SR10
SR75 = 3/4 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
50 lbS. 70 lbS.
1.5
2.0
2.0
2.4
2.4
3.0
3.5
4.0
5.0
7.0
SIGNATURe VAlVe
20003X521 20003X522 20003X522 20003X523 20003X523 20003X524 20003X525 20003X526 20003X527 CONSUlT
W/ PlASTIC bYPASS
FACTORY
& 3/4" S.S. YOKe
SIGNATURe VAlVe
20003X531 20003X532 20003X532 20003X533 20003X533 20003X534 20003X535 20003X536 20003X537
W/ PlASTIC bYPASS
& 1" S.S. YOKe
SIGNATURe VAlVe
20003X541 20003X542 20003X542 20003X543 20003X543 20003X524 20003X525 20003X526 20003X527
W/O bYPASS & YOKe
SIGNATURe VAlVe
20003X551 20003X552 20003X552 20003X533 20003X533 20003X534 20003X535 20003X536 20003X537
W/ bYPASS & 3/4" YOKe
PARTS
DeSCRIPTION
SIGNATURe VAlVe
20003X561 20003X562 20003X562 20003X563 20003X563 20003X564 20003X565 20003X566 20003X567
W/ PlASTIC bYPASS
& 1" YOKe
SIGNATURe VAlVe
20003X571 20003X572 20003X572 20003X573 20003X573 20003X574 20003X575 20003X576 20003X557
W/ STAINleSS STeel
bYPASS 3/4"
SIGNATURe VAlVe
20003X581 20003X582 20003X582 20003X583 20003X583 20003X584 20003X585 20003X586 20003X587
W/ STAINleSS STeel
bYPASS 1"
bRINe TANK ASSeMblY
40330X000
40440X000 40500X000
18 X 33
18 X 40 24 X 50
- 120 -
Parts Diagram - AT Series Softeners
ReF
NO.
PARTS
4
5
6
7
DeSCRIPTION
AT24(V)
AT24T
AT32(V)
AT32T
AT48(V)
AT48T
AT64(V)
AT64T
AT96V
ReSIN TANK PART NO. 30844X100 30844X100 30948X100 30948X100 31054X100 31054X100 31348X100 31348X100 31465X100
W/ bASe (2)
SIZe
8" X 44"
8" X 44" 9" X 48" 9" X 48" 10" X 54" 10" X 54" 13" X 48" 13" X 48" 14" X 65"
NA
30948V100
NA
31054V100
NA
31348V100
NA
31465V100
W/ bASe (2)
SIZe
9" X 42"
9" X 48"
10" X 54"
13" X 48"
14" X 65"
DISTRIbUTOR & TUbe
330044X11
N/A
330048X11
N/A
330054X11
N/A
330048X11
N/A
330065X11
ASSY. - (2) ReQUIReD
TURbUlATOR & TUbe
N/A
340044X11
N/A
340048X11
N/A
340054X11
N/A
340048X11
N/A
CATION ReSIN
(2) SR75 (2) SR75 (2) SR10 (2) SR10 (4) SR75 (4) SR75 (4) SR10 (4) SR10 (6) SR10
SR75 = 3/4 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
(2) DG50
CONTROl VAlVe W/ DlFC,
1.5
2.0
2.0
2.4
2.4
3.0
3.5
4.0
5.0
2nd TANK ADPT. & MeTeR
W/ PlASTIC bYPASS
20908X501 20908X502 20908X502 20908X503 20908X503 20908X504 20908X505 20908X506 20908X507
& 3/4" S.S. YOKe
-1Y MODelS - W/ PlASTIC 20908X511 20908X512 20908X512 20908X513 20908X513 20908X514 20908X515 20908X516 20908X517
bYPASS & 1" S.S. YOKe
-WO MODelS 20908X531 20908X532 20908X532 20908X533 20908X533 20908X534 20908X535 20908X536 20908X537
W/O bYPASS & YOKe
-P MODelS W/PlASTIC 20908X541 20908X542 20908X542 20908X543 20908X543 20908X544 20908X545 20908X546 20908X547
bYPASS & 3/4" YOKe
-1P MODelS -W/ PlASTIC 20908X551 20908X552 20908X552 20908X553 20908X553 20908X554 20908X555 20908X556 20908X557
bYPASS & 1" YOKe
-b MODelS W/STAINleSS 20908X561 20908X562 20908X562 20908X563 20908X563 20908X564 20908X565 20908X566 20908X567
STeel bYPASS 3/4"
-1b MODelS W/STAINleSS 20908X571 20908X572 20908X572 20908X573 20908X573 20908X574 20908X575 20908X576 20908X577
STeel bYPASS 1"
40330X000
40440X000
bRINe TANK ASSeMblY
18 X 33
18 X 40
INTeRCONNeCT PIPeS
20908X218
- 121 -
Parts Diagram - AT - 91 Twin Flow Series Softeners
ReF
NO.
DeSCRIPTION
INTeRCONNeCT PIPeS
3
4
5
AT96-91V
30844X100 30844X100 30948X100 30948X100 31054X100 31054X100 31348X100 31348X100 31465X100

8" X 44"
8" X 44" 9" X 48" 9" X 48"
10" X 54" 10" X 54" 13" X 48" 13" X 48" 14" X 65"
30942V100
NA
30948V100
NA
31054V100
NA
31348V100
NA
31465V100
9" X 42"
9" X 48"
10" X 54"
13" X 48"
14" X 65"
330044X11
N/A
330048X11
N/A
330054X11
N/A
330048X11
N/A
330065X11
N/A
340044X11
N/A
340048X11
N/A
340054X11
N/A
340048X11
N/A
(2) SR75
(2) SR75
(2) SR10
(2) SR10
(4) SR75
(4) SR75
(4) SR10
(4) SR10
(6) SR10
N/A
1.5
N/A
2.0
N/A
2.0
N/A
2.4
N/A
2.4
N/A
3.0
N/A
3.5
N/A
4.0
(2) DG50
5.0
20909X501 20909X502 20909X502 20909X503 20909X503 20909X504 20909X505 20909X506 20909X507

20909X511 20909X512 20909X512 20909X513 20909X513 20909X514 20909X515 20909X516 20909X517
PARTS
ReSIN TANK PART NO.

W/ bASe (2)
SIZe
VORTeCH TANK PART NO.
W/ bASe (2)
SIZe
DISTRIbUTOR & TUbe
TURbUlATOR & TUbe
CATION ReSIN
SR75 = 3/4 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
CONTROl VAlVe W/ DlFC,
2nd TANK ADPT. & MeTeR
W/ PlASTIC bYPASS
& 3/4" S.S. YOKe
-1Y MODelS - W/ PlASTIC
bYPASS & 1" S.S. YOKe
-WO MODelS W/O bYPASS & YOKe
-P MODelS W/PlASTIC
bYPASS & 3/4" YOKe
-1P MODelS -W/ PlASTIC
bYPASS & 1" YOKe
-b MODelS W/STAINleSS
STeel bYPASS 3/4"
-1b MODelS W/STAINleSS
STeel bYPASS 1"
bRINe TANK ASSeMblY
AT24(V)-91 AT24T-91 AT32(V)-91 AT32T-91 AT48(V)-91 AT48T-91 AT64(V)-91 AT64T-91
20909X521 20909X532 20909X532 20909X533 20909X533 20909X534 20909X535 20909X536 20909X537

20909X531 20909X542 20909X542 20909X543 20909X543 20909X544 20909X545 20909X546 20909X547
20909X541 20909X552 20909X552 20909X553 20909X553 20909X554 20909X555 20909X556 20909X557
20909X551 20909X562 20909X562 20909X563 20909X563 20909X564 20909X565 20909X566 20909X567
20909X561 20909X572 20909X572 20909X573 20909X573 20909X574 20909X575 20909X576 20909X577
40330X000
18 X 33
20908X218
40440X000
18 X 40
- 122 -
Parts Diagram - WF Series Filters
PARTS
ReF
NO.
DeSCRIPTION
1 MINeRAl TANK PART NO.

W/ bASe
SIZe
VORTeCH TANK PART NO.
W/ bASe
SIZe
2 DISTRIbUTOR & TUbe ASSY.
3 CONTROl VAlVe W/ DlFC
SIGNATURe VAlVe W/
PlASTIC bYPASS & S.S.
YOKe 3/4"
SIGNATURe VAlVe W/
PlASTIC bYPASS & S.S.
YOKe 1"
SIGNATURe VAlVe W/O
bYPASS & YOKe
SIGNATURe VAlVe W/
PlASTIC bYPASS & YOKe
3/4"
SIGNATURe VAlVe W/
PlASTIC bYPASS & YOKe 1"
WF10
30948X100
9" X 48"
30948V100
9" X 48"
330048X11
5.0
20002X521
WF15
WF20
31054X100 31348X100
10" X 54"
13 X 48
31054V100 31348V100
10" X 54"
13 X 48
330054X11 330048X11
5.0
7.0
20002X521 20002X523
WF25
31354X100
13" X 54"
31354V100
13" X 54"
330054X11
7.0
20002X523
WF30
31465X100
14" X 65"
31465V100
14" X 65"
330065X11
10.0
20002X524
WF40
31665X100
16 X 65
31665V100
16 X 65
330065X11
15.0
N/A
20002X531 20002X531 20002X533 20002X533 20002X534 CONSUlT

FACTORY
20002X541 20002X541 20002X543 20002X543 20002X544 CONSUlT
FACTORY
20002X551 20002X551 20002X553 20002X553 20002X554
N/A
20002X561 20002X561 20002X563 20002X563 20002X564 CONSUlT

FACTORY
20002X571 20002X571 20002X573 20002X573 20002X574
N/A
SIGNATURe VAlVe W/
S.S. bYPASS 3/4"
SIGNATURe VAlVe W/
20002X581 20002X581 20002X583 20002X583 20002X584 CONSUlT
S.S. bYPASS 1"
FACTORY
GRAVel UNDeRbeD ReQ. DG20
DG20
DG50
DG50
DG50
DG70
FIlTeR MeDIA CAPACITY 1.0 CU. FT. 1.5 CU. FT. 2.0 CU. FT. 2.5 CU. FT. 3.0 CU. FT. 4.0 CU. FT
OPTION - POlYGlASS TANK 30948X104 31054X104 31348X104 31354X104
N/A
N/A
W/ DOMe FIll PlUG - GRAY
OPTION - POlYGlASS TANK 30948X105 31054X105 31348X105 31354X105
W/ DOMe FIll PlUG - NATURAl
DOMe HOle PlUG USeD W/
35100X105
N/A
35100X105
POlYGlASS TANKS AbOVe
N/A
N/A
N/A
N/A
- 123 -
Parts Diagram - IF Series MTM Filters
ReF
NO.
DeSCRIPTION
IF15
IF20
IF25
30948X100
9" X 48"
30948X100
9" X 48"
330048X11
(1) MT10
31054X100
10" X 54"
31054X100
10" X 54"
330054X11
(2) MT75
31348X100
13 X 48
31348X100
13 X 48
330048X11
(2) MT10
31354X100
13" X 54"
31354X100
13" X 54"
330054X11
(1) MT10
(2) MT75
(1) DG20
(1) DG20
(1) DG50
(1) DG50
5.0
5.0
7.0
7.0
20001X528 20001X528 20001X530 20001X530
20001X538 20001X538 20001X540 20001X540
20001X548 20001X548 20001X550 20001X550
PARTS
1 MINeRAl TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
3 MTM
MT75 = 3/4 CU. FT.
MT10 = 1 CU. FT.
4 "D" GRAVel UNDeRbeD
DG20 20 lbS. "D" GRAVel
DG50 50 lbS. "D" GRAVel
SIGNATURe VAlVe W/ PlASTIC
bYPASS & S.S. YOKe 3/4"
bYPASS & S.S. YOKe 1"
SIGNATURe VAlVe W/O bYPASS
& YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
6 FeeDeR TANK
PART NO.
ASSeMblY
SIZe
IF10
20001X558 20001X558 20001X560 20001X560

20001X568 20001X568 20001X570 20001X570
20001X578 20001X578 20001X580 20001X580
20001X588 20001X588 20001X590 20001X590
40461X000
10" X 16"
- 124 -
Parts Diagram - U Series Filters
ReF
NO.
PARTS
2
3
DeSCRIPTION
MINeRAl TANK
PART NO.
W/ bASe
SIZe
VORTeCH
PART NO.
TANK W/ bASe
SIZe
MANIFOlD W/ DIFFUSeR &
O-RING 1" IN / OUT
GRAVel UNDeRbeD ReQUIReD
FIlTeR MeDIA CAPACITY
OPTION - POlYGlASS TANK
W/ DOMe FIll PlUG - GRAY
OPTION - POlYGlASS TANK W/
DOMe FIll PlUG - NATURAl
DOMe HOle PlUG USeD W/
POlYGlASS TANKS AbOVe
U10
U15
U20
30948X100
9" X 48"
30948V100
9" X 48"
330048X14
62128X109
31054X100
10" X 54"
31054V100
10" X 54"
330054X14
62128X109
31348X100
13 X 48
31348V100
13 X 48
330048X14
62128X109
U25
31354X100
13" X 54"
31354V100
13" X 54"
330054X14
62128X109
DG20
DG20
DG50
DG50
1.0 CU. FT. 1.5 CU. FT. 2.0 CU. FT. 2.5 CU. FT.
N/A
31054X104 31348X104 31354X104
N/A
31054X105 31348X105 31354X105
35100X105
N/A
35100X105
- 125 -
Parts Diagram - ATI Series eliminatr
ReF
NO.
DeSCRIPTION
ATI24
1 MINeRAl TANK PART NO. 30942X100

W/ bASe (2)
SIZe
9" X 42"
VORTeCH
PART NO. 30942V100
TANK W/bASe (2) SIZe
9" X 42"
2 DISTRIbUTOR & TUbe
330044X15
ASSY. - 2 ReQ'D.
TURbUlATOR & TUbe
N/A
ASSY. - 2 ReQ'D.
3 FINe MeSH CATION ReSIN (2) FR75
FR75 = 3/4 CU. FT.
FR10 = 1 CU. FT.
4 GARNeT SAND 8 X 12
(2) GS20
GS30 - 30 lbS.
GS70 - 70 lbS.
1.0
5 CONTROl VAlVe W/ DlFC,
ATI32
ATI48
ATI64
ATI96
30948X100
9" X 48"
30948V100
9" X 48"
330048X15
31054X100
10" X 54"
31054V100
10" X 54"
330054X15
31348X100
13" X 48"
31348V100
13" X 48"
330048X15
31465X100
14 X 65
31465V100
14 X 65
330065X15
N/A
N/A
N/A
N/A
(2) FR10
(4) FR75
(4) FR10
(6)FR10
(2) GS30
(2) GS30
(2) GS70
(2) GS70
1.2
1.5
2.4
3.0
W/ PlASTIC bYPASS &

S.S. YOKe 3/4"
-1Y MODelS - W/ PlASTIC
bYPASS & S.S. YOKe
W/O bYPASS & YOKe
-P MODelS - W/ PlASTIC
bYPASS & YOKe 3/4"
-1P MODelS - W/ PlASTIC
bYPASS & YOKe 1"
-b MODelS - W/ STAINleSS
STeel bYPASS 3/4"
-1b MODelS - W/ STAINleSS
STeel bYPASS 1"
6 bRINe TANK ASSY.
7 INTeRCONNeCT PIPeS
20908X500 20908X501 20908X502 20908X503
N/A
20908X510 20908X511 20908X512 20908X513 20908X514
PARTS
2ND TANK ADAPTOR & MeTeR
20908X530 20908X531 20908X532 20908X533 20908X534

20908X540 20908X541 20908X542 20908X543
N/A
20908X550 20908X551 20908X552 20908X553 20908X554
20908X560 20908X561 20809X562 20908X563
N/A
20908X570 20908X571 20908X572 20908X573 20908X574

40330X000
18" X 33"
20908X218
40440X000
18 X 40
Consult CSI
- 126 -
Parts Diagram - TSI Series eliminatr Systems
ReF
NO.
TSI24
TSI32
ReSIN TANK
PART NO. 30942X100 30948X100
W/ bASe
SIZe
9" X 42"
9" X 48"
VORTeCH
PART NO. 30942V100 30948V100
TANK W/ bASe
SIZe
9" X 42"
9" X 48"
DISTRIbUTOR & TUbe ASSY. 330044X15 330048X15

N/A
FINe MeSH CATION ReSIN (1) FR75
FR75 = 3/4 CU. FT.
FR10 = 1 CU. FT.
GS20
GS30 - 30 lbS. Standard
GS70 - 70 lbS. Tank Only
1.0
SIGNATURe VAlVe W/ PlASTIC 20001X529
SIGNATURe VAlVe W/O
20001X549
bYPASS & YOKe
bYPASS & 3/4" YOKe
bYPASS & 1" YOKe
SIGNATURe VAlVe W/
20001X579
STAINleSS STeel bYPASS 3/4"
SIGNATURe VAlVe W/
20001X589
STAINleSS STeel bYPASS 1"
6 bRINe TANK ASSY.
PARTS
DeSCRIPTION
TSI48
TSI64
TSI96
31054X100 31348X100 31465X100

10" X 54"
13" X 48"
14 X 65
31054V100 31348V100 31465V100
10" X 54"
13" X 48"
14 X 65
330054X15 330048X15 330065X15
N/A
(1) FR10
N/A
(2) FR75
N/A
(2) FR10
N/A
(3) FR10
GS30
GS30
GS70
GS70
1.2
20001X521
1.5
2.4
3.0
20001X522 20001X523 20001X524
20001X531
20001X532 20001X533 20001X534
20001X541
20001X542 20001X543 20001X544
20001X551 20001X552 20001X553 20001X554

20001X561 20001X562 20001X563 20001X564
20001X571
20001X572 20001X573 20001X574
20001X581
20001X582 20001X583 20001X584
40330X000
18 X 33
40440X000
18 X 40
- 127 -
Parts Diagram - MSI Series eliminatrSystems
ReF
NO.
DeSCRIPTION
MSI24
ReSIN TANK
PART NO. 30942X100 30948X100
W/ bASe
SIZe
9" X 42"
9" X 48"
VORTeCH
PART NO.
30942V100 30948V100
TANK W/ bASe
SIZe
9" X 42"
9" X 48"
DISTRIbUTOR & TUbe ASSY. 330044X15 330048X15
MSI48
MSI64
MSI96
31054X100 31348X100 31465X100

10" X 54"
13" X 48"
14 X 65
31054V100 31348V100 31465V100
10" X 54"
13" X 48"
14 X 65
330054X15 330048X15 330065X15
N/A
(1) FR10
N/A
(2) FR75
N/A
(2) FR10
N/A
(3) FR10
GS30
GS30
GS70
GS70
1.2
20003X521
1.5
2.4
3.0
20003X522 20003X523 20003X524
20003X531
20003X532 20003X533 20003X534
20003X541
20003X542 20003X543 20003X544
PARTS

N/A
FINe MeSH CATION ReSIN (1) FR75
FR75 = 3/4 CU. FT.
FR10 = 1 CU. FT.
GS20
GS30 - 30 lbS. Standard
GS70 - 70 lbS. Tank Only
1.0
SIGNATURe VAlVe W/O
20003X540
bYPASS & YOKe
bYPASS & 3/4" YOKe
bYPASS & 1" YOKe
SIGNATURe VAlVe W/
20003X570
STAINleSS STeel bYPASS 3/4"
SIGNATURe VAlVe W/
20003X580
STAINleSS STeel bYPASS 1"
6 bRINe TANK ASSY.
MSI32
20003X551 20003X552 20003X553 20003X554

20003X561 20003X562 20003X563 20003X564
20003X571
20003X572 20003X573 20003X574
20003X581
20003X582 20003X583 20003X584
40330X000
18 X 33
40440X000
18 X 40
- 128 -
Parts Diagram - TST Series Tannin Hardness System
ReF
NO.
2
3
PARTS
4
5
DeSCRIPTION
ReSIN TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
CATION ReSIN
TANNIN ReSIN
SR50 = 1/2 CU. FT. TR25 = 1/4 CU. FT.
SR75 = 3/4 CU. FT. TR50 = 1/2 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
& YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
SIGNATURe VAlVe W/ STAINleSS
STeel bYPASS 3/4"
STeel bYPASS 1"
bRINe TANK ASSeMblY 40330X000
TST24
TST32
TST48
TST64
30942X100
9" X 42"
30942X100
9" X 42"
330044X11
N/A
(1) SR50
(1) TR25
30948X100 31054X100 31348X100

9" X 48"
10" X 54"
13" X 48"
30948X100 31054X100 31348X100
9" X 48"
10" X 54"
13" X 48"
330048X11 330054X11 330048X11
N/A
N/A
N/A
(1) SR75
(1) SR10
(2) SR75
(1) TR25
(1) TR50
(1) TR50
N/A
1.0
20001X529
N/A
N/A
N/A
1.2
1.5
2.4
20001X521 20001X522 20001X523
20001X539
20001X531 20001X532 20001X533
20001X549 20001X541 20001X542 20001X543

20001X559
20001X551 20001X552 20001X553
20001X569
20001X561 20001X562 20001X563
20001X579
20001X571 20001X572 20001X573
20001X589
20001X581 20001X582 20001X583

40330X000
18 X 33
- 129 -
Parts Diagram - MST Series Tannin Hardness System
ReF
NO.
2
3
4
5
ReSIN TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
CATION ReSIN
TANNIN ReSIN
SR50 = 1/2 CU. FT. TR25 = 1/4 CU. FT.
SR75 = 3/4 CU. FT. TR50 = 1/2 CU. FT.
SR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
& YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
STeel bYPASS 3/4"
STeel bYPASS 1"
bRINe TANK ASSeMblY
MST24
MST32
MST48
MST64
30942X100 30948X100 31054X100 31348X100

9" X 42"
9" X 48"
10" X 54"
13" X 48"
30942X100 30948X100 31054X100 31348X100
9" X 42"
9" X 48"
10" X 54"
13" X 48"
330044X11 330048X11 330054X11 330048X11
N/A
N/A
N/A
N/A
(1) SR50
(1) SR75
(1) SR10
(2) SR75
(1) RF25
(1) TR25
(1) TR50
(1) TR50
N/A
1.0
20003X520
N/A
N/A
N/A
1.2
1.5
2.4
20003X521 20003X522 20003X523
20003X530
20003X531 20003X532 20003X533
20003X540 20003X541 20003X542 20003X543

20003X550
20003X551 20003X552 20003X553
20003X560
20003X561 20003X562 20003X563
20003X570
20003X571 20003X572 20003X573
20003X580
20003X581 20003X582 20003X583
PARTS
DeSCRIPTION
40330X000
18 X 33
- 130 -
Parts Diagram - TN Nitrate / Sulfate System
ReF
NO.
2
3
PARTS
4
5
DeSCRIPTION
ReSIN TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
NITRATe ReSIN
NR75 = 3/4 CU. FT.
NR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
& YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
STeel bYPASS 3/4"
STeel bYPASS 1"
bRINe TANK ASSY.
TN15
TN25
31054X100 31354X100
10" X 54"
13" X 54"
31054X100 31354X100
10" X 54"
13" X 54"
330054X11 330054X11
N/A
N/A
(2) NR75
(2) NR75
(1) NR10
N/A
N/A
1.2
2.4
20001X522 20001X525
20001X532 20001X535
20001X542 20001X545
20001X552 20001X555
20001X562 20001X565
20001X572 20001X575
20001X582 20001X585
40330X000
18 X 33
- 131 -
Parts Diagram - MN Nitrate / Sulfate System
ReF
NO.
2
3
4
5
ReSIN TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
NITRATe ReSIN
NR75 = 3/4 CU. FT.
NR10 = 1 CU. FT.
"D" GRAVel UNDeRbeD
& YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
STeel bYPASS 3/4"
STeel bYPASS 1"
bRINe TANK ASSY.
TN15
TN25
31054X100 31354X100
10" X 54"
13" X 54"
31054X100 31354X100
10" X 54"
13" X 54"
330054X11 330054X11
N/A
N/A
(2) NR75
(2) NR75
(1) NR10
N/A
N/A
1.2
2.4
20001X522 20001X525
20001X532 20001X535
20001X542 20001X545
20001X552 20001X555
PARTS
DeSCRIPTION
20001X562 20001X565
20001X572 20001X575
20001X582 20001X585
40330X000
18 X 33
- 132 -
Parts Diagram - Ultra Violet Systems

Trojan - UVMAX
General
Specifications
UVMAX C4 UVMAX D4 UVMAX e4 UVMAX F4
PRO10
PRO20
PRO30
lamp
602805
602805
602806
602807
602854
602855
602856
Sleeve
602732
602732
602733
602734
602974
602975
602976
21.4 x 4in.
31 x 4in.
41 x 4in.
Chamber
19.5 x 3.5in. 19.5 x 3.5in.
29 x 3.5in. 43.5 x 3.5in.
PARTS
WEDECO - DLR
ReF.
NO.
PART
NO.
1
2
3
4
5
6
7
8
9
10
10A
11
12
13
14**
15**
16**
*
*
DQ36648
AQ37086
AQ35492
AQ36538
AQ36617
AQ36799
AQ702576
AQ36942
AQ36992
*
*
*
*
*
AQ36944
DeSCRIPTION
eleCTRICAl CONTROl bOX
DISINFeCTION CHAMbeR
QUARTZ SleeVe
UlTRAVIOleT lAMP
HeAD PIeCe O-RING
HeAD PIeCe
GlO-CAP O-RING
GlO-CAP
SeNSOR ASSeMblY(eXClUDeS APMODel)
eleCTRICAl CONTROl bOX STRAP
STRAP bUCKle
WAll MOUNT bRACKeT
WAll MOUNT bRACKeT STRAP
WAll MOUNT bRACKeT STRAP SCReW
FlOW CONTROl
SOleNOID VAlVe (OPTIONAl)
POWeR CORD
QTY.
1
1
1
1
1
1
1
1
1
2
2
2
2
4
1
1
1
* Determined by serial number

** Not Shown
- 133 -
Parts Diagram - Reactr RF Series Tanks
ReF PART NO.

NO.
1
65555X330
65555X000
"RF" SeRIeS
3
4
5
6
30948X000
32009X103
65555X214
65555X229
DeSCRIPTION
ReACTR MANIFOlD ASSeMblY - 5.0 GPM
INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS,
DIFFUSeR, AIR INleT VAlVe CHeCK, FlOAT ASSeMblY,
CHlORINe PORT PlUG, eXHAUST VeNT HOSe bARb
AND TUbING
ReACTR TANK & MANIFOlD ASSeMblY COMPleTe
INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS,
DIFFUSeR, AIR INleT VAlVe CHeCK, FlOAT ASSeMblY,
CHlORINe PORT PlUG, eXHAUST VeNT HOSe bARb,
TUbING, 9" X 48" POlYGlASS TANK, AeRATION bAllS,
bOTTOM elbOW ASSeMblY
9" X 48" TANK W/ bASe
9" TANK bASe
AeRATION bAllS - 50 PeR PKG. - 1 ReQ'D.
FITTING PACKAGe - ReACTR TANK bOTTOM
PARTS
- 134 -
PARTS
Parts Diagram - Reactr UT & RF Filter Tanks
ReF
DeSCRIPTION
NO.
1
TANK
PART NO.
W/ bASe
SIZe
VORTeCH TANK
PART NO.
W/ bASe
SIZe
3 "D" GRAVel UNDeRbeD
DG20 = 20 lbS.
DG50 = 50 lbS.
4 ReACTR bleND MeDIA
Rb75 = 3/4 CU. FT.
Rb10 = 1 CU. FT.
SIGNATURe VAlVe W/O
bYPASS & YOKe
bYPASS & YOKe 3/4"
bYPASS & YOKe 1"
STeel bYPASS 3/4"
STeel bYPASS 1"
RF10
RF15
RF20
RF25
RF30
UT40
UT10
UT15
UT20
UT25
UT30
30948X100 31054X100 31348X100 31354X100 31465X100 31665X100
9" X 48"
10" X 54"
13 X 48
13" X 54"
14" X 65"
16" X 65"
30948V100 31054V100 31348V100 31354V100 31465V100 31665V100
9" X 48"
10" X 54"
13 X 48
13" X 54"
14" X 65"
16" X 65"
330048X11 330054X11 330048X11 330054X11 330065X11 330065X11
(1) DG20
(1) DG20
(1) DG50
(1) DG50
(1) DG50
(1) DG70
(1) Rb10
(2) Rb75
(2) Rb10
(2) Rb75
(1) Rb10
(3) Rb10
(4) Rb10
5.0
20005X521
5.0
7.0
7.0
10.0
15.0
20005X521 20005X523 20005X523 20005X524 20005X525
20005X531
20005X531 20005X533 20005X533 20005X534 20005X535
20005X541
20005X541 20005X543 20005X543 20005X544 20005X545
20005X551
20005X551 20005X553 20005X553 20005X554 20005X555
20005X561
20005X561 20005X563 20005X563 20005X564 20005X565
20005X571
20005X571 20005X573 20005X573 20005X574 20005X575
20005X581
20005X581 20005X583 20005X583 20005X584 20005X585
- 135 -
Parts Diagram - Reactr UT Series Tanks

ReF
NO.
PART NO.
65555X340
3
4
DeSCRIPTION
ReACTR MANIFOlD ASSeMblY - 5.0 GPM

INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS, DIFFUSeR,
AIR INleT VAlVe CHeCK, FlOAT ASSeMblY, CHlORINe PORT
PlUG, eXHAUST VeNT HOSe bARb AND TUbING
65555X010
"UT30" ReACTR TANK & MANIFOlD ASSY. COMPleTe
"UT30" SeRIeS INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS, DIFFUSeR,
PlUG, eXHAUST VeNT HOSe bARb, 16" X 44" "UT" TANK, AIR
VeNT TUbING AND AeRATION bAllS
65555X020
"UT40" ReACTR TANK & MANIFOlD ASSY. COMPleTe
" "UT40" SeRIeS INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS, DIFFUSeR,
65555X030
"UT40S" ReACTR TANK & MANIFOlD ASSY. COMPleTe
"UT40S" SeRIeS INClUDeS : MANIFOlD, ReACTR bODY, DIAPHRAGMS, DIFFUSeR,
30030X100
16" X 44" "UT" TANK ONlY
30040X100
16" X 56" "UT40" TANK ONlY
30040X101
21" X 35" "UT40S" TANK ONlY
65555X214
AeRATION bAllS - 50 PeR PKG. - 2 ReQ'D.
PARTS
- 136 -
PARTS
Parts Diagram - Reactr body & Manifold Assembly
ReF
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
65555X221
65555X205
65555X217
65555X215
65555X236
65555X237
65555X238
65555X219
65555X208
65555X220
65555X212
65555X213
65555X210
65555X209
65555X216
65555X230
DeSCRIPTION
SCReW 1/4-20 X 3.5" S.S. PHIllIPS
ReACTR bODY W/ NOZZle & THROAT ONlY - 5.0 GPM
HOSe bARb - 1/4" X 1/4" NPT-M
AIR INTAKe VAlVe CHeCK ASSeMblY
AIR INTAKe VAlVe CHeCK VITON O-RING - 2 ReQ'D.
AIR INTAKe VAlVe CHeCK bODY ASSeMblY ONlY
AIR INTAKe VAlVe CHeCK ONlY
DIAPHRAGMS - 2 ReQ'D.
MANIFOlD - ReACTR ONlY
O-RING - MANIFOlD TO TANK SeAl
DIFFUSeR W/ SCReWS
1/8" NPT PlASTIC PIPe PlUG
FlOAT ASSeMblY FOR "RF" SeRIeS
FlOAT ASSeMblY FOR "UT" SeRIeS / HYDROXR
3/8" OD X 1/4" ID X 12 FT. VeNT TUbING
1/4 NPT PlASTIC PIPe PlUG
- 137 -
Parts Diagram - Reactr Oxyclean Option
PART NO.
OXY-08
DeSCRIPTION
COMPleTe "OXYCleAN" OPTION - INCl. ReF. NO. 1,

5, 8, 13 & (2) ClAMPS
1
66555X100
OXYCleAN PUMP ASSY. INCl. PUMP, HOSe & eNClOSURe
2
66555X101
OXYCleAN PUMP TUbING - (82" lONG)
3
66555X102
HOSe bARb TYPe CHeCK VAlVe
4
66555X112
HIGH PReSSURe TUbING, SAFeTY CHeCK, & ClAMPS
5
66555X115
COMPleTe ASSeMblY - INCl. ReF. NO. 3 & 4
6
66555X116
HIGH PReSSURe TUbING
7
66555X104
5 GAl. SOlUTION TANK ONlY
8
66555X103
5 GAl. SOlUTION TANK W/ bUlKHeAD FITTING
9
66555X105
SOlUTION TANK bUlKHeAD FITTING ONlY
10
65555X217
HOSe bARb - 1/4" X 1/4" NPT-M
Not
66555X106
OXYCleAN TUbING ClAMP ONlY - 2 ReQ'D.
Shown
11
65555X107
OXYCleAN PUMP ONlY
12
65555X108
OXYCleAN PUMP eNClOSURe ASSY. ONlY
13
SSRbO1
RelAY bOX FOR ReACTR OXYCleAN
NOTe : OXYCleAN OPTION ReQUIReS SIGNATURe OR 2510 ReACTR VAlVe
FOR POWeR SUPPlY AND CYClING.
PARTS
ReF
NO.
- 138 -
Parts Diagram - 40330X000 brine System
PARTS
15
ReF
NO.
PART NO.
40330X000
40330X010
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
40330X020
40330X100
40330X101
40330X102
40330X103
40330X104
40330X105
40330X106
40330X107
40330X108
40330X109
40330X112
40330X117
40330X118
40330X119
40330X110
DeSCRIPTION
18 X 33 bRINe TANK ASSY. COMPleTe
INJeCTION MOlDeD CSI lID
18 X 33 bRINe TANK ASSY. COMPleTe
blOW MOlDeD lID
bRINe TANK & lID ONlY - blOW MOlDeD
TANK bOTTOM ONlY
lID ONlY - INJeCTION MOlDeD CIS
lID ONlY - blOW MOlDeD
3/8" OD X 1/4" ID X 4' bRINe TUbING
4" bRINe Well CAP
4" X 28" bRINe Well
OVeRFlOW FITTING & NUT
SAFeTY bRINe VAlVe, FlOAT & AIR CHeCK
18" POlY GRID PlATe
GROMMeT
FlOAT ASSY.
# 500 AIR CHeCK - 48 lONG
SAFeTY bRINe, VAlVe ONlY
GROMMeT ReTAINeR
NUT & FeRRUle KIT
- 139 -
Parts Diagram - 3/4 Plastic bodied Meter Parts
ReF. PART
NO. NO.
0 20563X200
1 20561X134
2 20563X202
20563X211
2b 20253X202
20253X203
3 20563X203
4 20563X204
5 20561X217
6 20561X201
7 20563X207
8 20561X216
9 20563X209
DeSCRIPTION
MeTeR MODUle COMPleTe - STD. RANGe
MeTeR COVeR ASSY. SCReW
MeTeR COVeR ASSY. - STD. RANGe
MeTeR COVeR ASSY. - eXT. RANGe
MeTeR COVeR - RIGHT ANGle - STD. RANGe
MeTeR COVeR - RIGHT ANGle - eXT. RANGe
MeTeR COVeR ASSY. O-RING
IMPelleR
ADAPTeR ClIP SCReW
ADAPTeR ClIP
MeTeR bODY
MeTeR bODY O-RING
FlOW STRAIGHTeNeR
QTY.
1
4
1
1
1
1
1
1
4
4
1
4
1
Shaded ReF. No. Indicates Assembly or Kit
PARTS
- 140 -
PARTS
Parts Diagram - Signature Valve Powerhead Assembly
- 141 -
Parts list - Signature Valve Powerhead Assembly
ReF. PART
NO. NO.
0
20001X100
20002X100
20003X100
20003X101
20005X100
1A 20001X101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
N/S
N/S
N/S
20001X106
20001X109
20001X110
20001X111
20001X112
20001X113
20001X114
20001X116
20001X118
20001X119
20001X120
20001X121
20001X122
20001X124
20001X125
DeSCRIPTION
Timeclock Softener Powerhead Assembly Complete
Filter Powerhead Assembly Complete
Metered Softener Powerhead Assembly w/ Meter
Metered Softener Powerhead Assembly w/o Meter
Reactr Powerhead Assembly Complete
Circuit board Assembly Includes (1) Ref.
#1, (5) Ref. #2 & (1) Ref. #3
Circuit board
Screw
Front Cover and label
Rear Cover
Indicator Dial
Hayco Fitting
Screw
Washer
Drive Motor 12 VDC
Screw
Screw
back Plate
Front Plate
Main Gear
encoder Wheel
brine Cam
encoder
Power Supply (not pictured)
QTY.
1
1
1
1
1
1
1
5
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
N/S = Non Stocked Item

PARTS
- 142 -
PARTS
Parts Diagram - Signature Series Control Valve Assembly
- 143 -
Parts list - Signature Series Control Valve Assembly
ReF.
NO.
PART
NO.
0
1
2
3
4
20001X200
20001X201
N/S
N/S
N/S
20001X232
4A
5
6
7
8
9A
10
11
12
13
14
15
16
17
18
18A
19
20
21
21A
Valve body Complete

Valve body Only
end Spacer
Spacer
Seal
Seal & Spacer Kit Includes (1) Ref. #2,
(4) Ref. #3 & (5) Ref. #4
N/S
DownFlow Piston
N/S
Piston Rod Retainer
N/S
end Plug Assembly
N/S
Hex Washer HD. 10-24 X 13/16 Screw
20001X231 Piston Assembly Includes (1) Ref. #5,
(1) Ref. #6, (1) Ref. #7, & (1) Ref. #9
N/S
brine Valve Stem
N/S
brine Valve Seat
N/S
brine Valve Spacer
N/S
Quad Ring
N/S
O-Ring
N/S
brine Valve Cap
N/S
brine Valve Spring
N/S
Plain Nylon Washer
N/S
Retaining Ring
20561X225 brine Assembly Includes Ref. #10 Thru 18
20251X254 O-Ring
20251X266 Flow Control button 1.5 GPM
N/S
Plastic Flow Control Housing
Flow Control Assembly - Specify GPM on Order.
Includes (1) #19, (1) #20, (1) #21, & (1) #39
20251X256 Flow Control Assembly 1.5 GPM - PVC
20001X214 Drain Retainer
20561X204 O-Ring
20001X215 O-Ring
N/S
O-Ring
N/S
Injector Plug
N/S
O-Ring
QTY.
1
1
1
4
5
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ReF.
NO.
PART
NO.
DeSCRIPTION
20001X217 Injector Plug & O-Ring Assembly Includes

(1) #25, (1) #26, & (1) #27
28
N/S
Injector Throat
29
N/S
Injector Nozzle
30
N/S
Vortex Generator
20001X219 Injector Assembly - Specify Size. Includes
30A
1 each of Ref. #25, 27, 28, 29, & 30
31 20001X222 Injector Screen
32 20001X224 Injector Seal
33 20001X223 Injector Cap
34 20001X226 10-24 X 1 Hex Washer HD Screw
20001X220 Injector Kit - Specify Size. Includes 1 each
34A
of Ref. #30A, 31, 32, 33, & (2) of Ref. #34
35 20561X239 O-Ring
36 20561X240 blFC button Retainer
37 20251X318 5 GPM blFC button
38 20561X241 blFC Adapter
38A 20001X228 blFC Assembly .5 GPM. Includes 1
each of Ref. #35, 36, 37, & 38
39 20251X255 Drain line Fitting 90 Degree elbow
1/2 NPT X 1/2 Tubing
27A
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
Items 45 Thru 48 Used Only With Clock Regen.

45
46
N/S
Adapter Coupling
20561X216 O-Ring
20561X215 Adapter Coupling & O-Ring Assembly.
46A
Includes Ref. (1) #45 & (2) #46
47 20561X201 Mounting Clip
48 20561X217 8-18 X 5/8 Hex Washer HD Screw
2
4
1
2
2

PARTS
22
23
24
25
26
27
DeSCRIPTION
1
1
1
2
1
2
- 144 -
PARTS
Parts Diagram - Signature Series Control Valve Assembly (Filter)
- 145 -
Parts list - Signature Series Control Valve Assembly (Filter)
ReF.
NO.
PART
NO.
0
1
2
3
4
20001X200
20001X201
N/S
N/S
N/S
20001X232
4A
5
6
7
8
9A
14
15
15A
19
20
21
21A
Valve body Complete

Valve body Only
end Spacer
Spacer
Seal
Seal & Spacer Kit Includes (1) Ref. #2,
(4) Ref. #3 & (5) Ref. #4
N/S
DownFlow Piston
N/S
Piston Rod Retainer
N/S
end Plug Assembly
N/S
Hex Washer HD. 10-24 X 13/16 Screw
20001X231 Piston Assembly Includes (1) Ref. #5,
(1) Ref. #6, (1) Ref. #7, & (1) Ref. #9
N/S
O-Ring
N/S
brine Valve Cap
20001X230 O-Ring & brine Valve Plug Assembly
20251X254 O-Ring
N/S
Plastic Flow Control Housing
Flow Control Assembly - Specify GPM on Order.
Includes (1) #19, (1) #20, (1) #21, & (1) #39
20001X214 Drain Retainer
20561X204 O-Ring
20001X215 O-Ring
N/S
O-Ring
N/S
Injector Plug
N/S
O-Ring
QTY.
1
1
1
4
5
1
1
1
1
3
1
1
1
1
1
1
ReF.
NO.
PART
NO.
DeSCRIPTION
20001X217 Injector Plug & O-Ring Assembly Includes

(1) #25, (1) #26, & (1) #27
32 20001X224 Injector Seal
33 20001X223 Injector Cap
34 20001X226 10-24 X 1 Hex Washer HD Screw
35
N/S
O-Ring
38
N/S
Filter Plug
1
38A 20001X229 O-Ring & Filter Plug Assembly. Includes
1 each of Ref. #35 & #38
39 20251X255 Drain line Fitting 90 Degree elbow
1/2 NPT X 1/2 Tubing
27A
QTY.
1
1
1
2
1
1
1
Items 45 Thru 48 Used Only With Clock Regen.

45
46
N/S
Adapter Coupling
20561X216 O-Ring
20561X215 Adapter Coupling & O-Ring Assembly.
46A
Includes Ref. (1) #45 & (2) #46
47 20561X201 Mounting Clip
48 20561X217 8-18 X 5/8 Hex Washer HD Screw
2
4
1
2
2
Filter Components Not Shown

34A 20001X221 Filter Conversion Kit. Includes 1 each of
Ref. #15A, 27A, 38A, 32, 33, & (2) # 34s
1
1

1
1
1
2
1
2
PARTS
22
23
24
25
26
27
DeSCRIPTION
- 146 -
Parts Diagram - 2510 Series Valve
PARTS
FILTER
- 147 -
Parts list - 2510 Series Valve Parts
ReF.
NO.
PART
NO.
1
2
3
4
20251X450
20251X210
20251X211
20251X212
20251X232
4A
5
6
7
8
9
10
20251X215
20251X218
20251X216
20251X221
20251X219
20251X222
10A 20251X231
11
12
13
14
24
25
26
27
28
29
30
20251X451
20251X452
20251X453
20001X215
20561X204
20251X454
20251X455
15
16
17
18
19
20
VAlVe bODY
eND SPACeR
SeAl RING
SPACeR
SeAl & SPACeR KIT INCl. (1)
NO. 2, (6) NO. 3 & (5) NO. 4
PISTON
PISTON ROD ReTAINeR
PISTON ROD
QUAD RING SeAl
eND PlUG O-RING SeAl
eND PlUG ASSeMblY
PISTON ASSeMblY INCl. (1)
eA. NO 5, 6, 7, 8 9 & 10
INJeCTOR bODY GASKeT
INJeCTOR bODY - PlASTIC
INJeCTOR SCReeN
INJeCTOR THROAT, # 1 WHITe
INJeCTOR THROAT, # 2 blUe
INJeCTOR THROAT, # 2 PVC
INJeCTOR NOZZle, # 1 WHITe
INJeCTOR NOZZle, # 2 blUe
INJeCTOR NOZZle, # 2 PVC
INJeCTOR COVeR GASKeT
INJeCTOR COVeR (PlASTIC bODY)
INJeCTOR bODY SCReW
DRAIN ReTAINeR
FlOW CONTROl bUTTON 1.5 GPM
FlOW CONTROl O-RING SeAl
FlOW CONTROl HOUSING - PlASTIC
1/2" PIPe X 1/2" HOS X 90
DRAIN FITTING
bASe SeAl
ADAPTeR bASe (2.5 - 8 THReAD)
SlIP RING
TANK O-RING
DISTRIbUTOR O-RING
DISTRIbUTOR TUbe O-RING ReTAINeR
ClAMP ASSeMblY
QTY.
ReF.
NO.
1
1
6
5
1
31
32
33
34
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Not
Shown
PART
NO.
DeSCRIPTION
20251X456 ClAMP PIVOT

20251X457 ClAMP SCReW
20252X202 CAP - FIlTeR ONlY
20252X201 CAP SeCURING SCReWS - FIlTeR ONlY
FlOW CONTROl ASSeMblY INCl. 20, 21 & 22
20251X256 FlOW CONTROl ASSY. 1.5 GPM - PVC
QTY.
1
1
1
2
1
1
1
1
1
1
1
1

PARTS
21
22
23
20251X208
20251X207
20251X204
20251X206
20251X242
20251X236
20251X205
20251X241
20251X235
20251X203
20251X202
20251X201
20001X214
20251X266
20251X267
20251X268
20251X269
20251X270
20251X271
20251X272
20251X274
20251X254
N/S
20251X255
DeSCRIPTION
1
1
1
1
1
1
1
- 148 -
PARTS
Parts Diagram - 2510 Series Valve 3200 Day Regeneration Timer
- 149 -
Parts list - 2510 Series Valve 3200 Day Regeneration Timer
ReF.
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
NOT
SHOWN
NOT
SHOWN
35
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
DeSCRIPTION
20251X104 3200 TIMeR ASSeMblY - 12 DAY

20251X105 3200 TIMeR ASSeMblY - 7 DAY
20251X401 TIMeR HOUSING
20251X402 CYCle ACTUATOR ARM
20251X403 24 HOUR GeAR
20251X405 KNOb
20251X406 SCReW - TIMeR KNOb & MOTOR MOUNT
20251X407 bUTTON DeCAl
20251X408 SKIPPeR WHeel ASSeMblY - 12 DAY
20251X410 ReGeNeRATION POINTeR
20251X411 SPRING ClIP
20251X412 SPRING - SKIPPeR WHeel DeTeNT
20251X413 bAll - 1/4" DIAMeTeR
20251X414 SPRING - MAIN GeAR DeTeNT
20251X415 MAIN DRIVe GeAR
20251X416 PROGRAM WHeel
20251X417 ROll PIN
20251X419 I IDleR SHAFT
20251X420 IDleR SPRING
20251X421 IDleR GeAR
20251X422 DRIVe GeAR
20251X423 CURVeD WASHeR
20251X424 MOTOR MOUNTING PlATe
20251X425 MOTOR - 110 V / 60 HZ
20251X426 SCReW - MOTOR MOUNTING
20251X427 SCReW - TIMeR HINGe
20251X428 HINGe bRACKeT
20251X429 INSUlATOR
20251X430 SWITCH
20251X431 SWITCH
20251X432 SCReW - SWITCH MOUNTING
20251X433 DeCAl - TIMe OF DAY
20251X434 DeCAl - INSTRUCTIONS
20251X435 SKIPPeR WHeel RING
N/S
HARNeSS (NOT SHOWN)
20251X438 1/4" DIAMeTeR DelRIN bAll
20251X441 GROUND WIRe (NOT SHOWN)
20251X404 24 HOUR lAbel - SIlVeR
N/S
SKIPPeR WHeel lAbel
N/S
PROGRAM WHeel DeCAl
QTY.
1
1
1
1
1
1
5
1
1
1
1
2
2
1
1
1
21
1
1
1
1
1
1
1
2
3
1
3
1
1
2
1
1
1
1
1
1
1
1
1
PARTS
21
22
23
24
25
26
27
28
29
30
31
32
PART
NO.

- 150 -
PARTS
Parts Diagram - 2510 Valve 3210 econominder Meter Regeneration Timer
- 151 -
Parts list - 2510 Valve 3210 econominder Meter Regeneration Timer
ReF.
NO.
0
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
DeSCRIPTION
20253X100 3210 MeTeR VAlVe TIMeR, 3/4" STD

RANGe W/ CAble - SPeCIFY "K"
20253X109 TIMeR HOUSING
20251X405 KNOb
20251X406 SCReW - TIMeR KNOb & MOTOR MOUNT
20251X407 bUTTON DeCAl
20253X113 PROGRAM WHeel ASSeMblY - SPeCIFY "K"
20253X111 PROGRAM WHeel ReTAINeR
20253X108 PROGRAM WHeel SCReW
20251X411 SPRING ClIP
20251X414 SPRING - MAIN GeAR DeTeNT
20251X438 bAll - 1/4" DIAMeTeR DelRIN
20251X415 MAIN DRIVe GeAR
20251X416 PROGRAM WHeel
20251X417 ROll PIN
20251X419 IDleR SHAFT
20251X425 MOTOR - 110 V / 60 HZ
20251X426 SCReW - MOTOR MOUNTING
20563X137 DRIVe PINION - PROGRAM WHeel
20563X138 ClUTCH - DRIVe PINION
20563X140 SPRING
20563X139 SPRING ReTAINeR
20251X427 SCReW - TIMeR HINGe
20251X428 HINGe bRACKeT
20251X429 INSUlATOR
20251X430 SWITCH
20251X431 SWITCH
20251X432 SCReW - SWITCH MOUNTING
20251X433 DeCAl - TIMe OF DAY
20251X434 DeCAl - INSTRUCTIONS
20501X122 WIRe CONNeCTOR (NOT SHOWN)
20251X441 GROUND WIRe (NOT SHOWN)
QTY.
1
1
1
1
1
5
1
1
1
1
1
2
2
1
1
21
1
1
1
1
1
1
1
2
1
1
1
1
3
1
3
1
1
2
1
1
2
1
PARTS
23
24
25
26
27
28
29
31
32
33
34
35
36
37
38
PART
NO.

- 152 -
PARTS
Parts Diagram - brine System for 2510 Valve
ReF. PART
NO. NO.
0 20251X300
1 20251X301
2 20251X302
3 20251X303
4 20251X305
5 20251X304
6 20251X306
7&11 20251X318
8 20251X316
9 20251X315
10 20251X314
12 20251X308
13 20251X307
14 20251X311
15 20251X313
16
17 20251X312
19 20251X317
DeSCRIPTION
.5 GPM bRINe VAlVe SYSTeM COMPleTe
1/4" NPT X 3/8" NPS 90 elbOW
bRINe lINe SCReeN
INSeRT SleeVe (3/8" TUbe)
DelRIN SleeVe (3/8" TUbe)
TUbe FITTING NUT 3/8" bRINe
bRINe VAlVe TUbe
ASSeMblY GFN NUT
O-RING
SeAT, bRINe VAlVe
bRINe VAlVe STeM 1600
GUIDe, bRINe VAlVe STeM
ReTAINING RING
bRINe VAlVe SPRING
bRINe VAlVe bODY PlASTIC
3/8" TUbING
elbOW, 3/8 TUbe POlY, WHITe
bRINe lINe FlOW CONTROl ASSY. - .5 blFC
QTY.
1
1
1
3
1
1
1
2
1
1
1
1
1
1
1
1
1
1
- 153 -
Parts Diagram - 2510 Series Valve Timer

ReF.
NO.
1
2
Not
Shown
Not
Shown
3
4
5
7
10
11
12
13
14
15
16
PART
NO.
DeSCRIPTION
20251X130 bACKPlATe FOR 2500 DeSIGNeR

20253X100 3210 MeTeR VAlVe TIMeR W/ CAble
3/4" STD MeTeR - SPeCIFY "K" lAbel
20251X104 3200 TIMeR ASSY. 12 DAY
20251X105 3200 TIMeR ASSY. 7 DAY
20251X101 POWeR CORD
20251X102 STRAIN RelIeF
20251X132 WIRING HARNeSS
20251X128 DRIVe MOTOR MOUNTING SCReW
20251X124 MOTOR MOUNTING bRACKeT
20251X123 SCReW 1/4"-20 X 1/2"
20251X114 INSUlATOR
20251X113 MICROSWITCH
20251X115 CONNeCTING lINK PIN
20251X307 ReTAINING RING
N/S
CONNeCTING lINK
QTY.
ReF.
NO.
PART
NO.
1
1
17
18
19
20
21
22
23
20251X118
20251X119
N/S
20251X125
20251X126
20251X127
20251X309
20251X310
20253X104
20253X105
20251X103
20251X135
N/S
20251X425
1
1
1
1
1
5
1
2
2
2
1
1
1
24
25
Not
Shown
Not
Shown
Not
Shown
Not
Shown
DeSCRIPTION
DRIVe CAM ASSeMblY (WHITe)
ROll PIN
DRIVe beARING
SCReW 4-40 X 1"
DRIVe MOTOR
bRINe VAlVe SIDe bRACKeT
bRINe CAM WHITe
bRINe CAM blACK
MeTeR CAble GUIDe
10.5" MeTeR CAble
TIMeR MOUNTING SCReW
DeSIGNeR COVeR (blACK PlASTIC)
SlANT COVeR
3200 OR 3210 TIMeR MOTOR 110 V / 60 Hz
QTY.
1
2
1
2
1
1
1
1
1
1
2
1
1
1
PARTS
- 154 -
PARTS
Parts Diagram - 5600 Series Valve Softener & Filter
- 155 -
Parts list - 5600 Series Valve Softener & Filter
ReF.
NO.
PART
NO.
0
1
2
3
4
5
7
7A
8
20561X200
20561X201
20561X202
20561X203
20561X204
20561X205
20561X207
20561X253
20561X208
8A 20561X254
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
VAlVe bODY COMPleTe

ADAPTeR ClIP
SeAl
VAlVe bODY ONlY 1.05" DIST.
DIST. TUbe O-RING 1.05" O.D.
VAlVe TO TANK O-RING
SPACeR
SeAl & SPACeR KIT INCl. 5 - #2 & 4 - #7
PISTON ONlY
PISTON & eND PlUG ASSY. INCl. #8,
9, 10, 11 & 12
PISTON PIN
PISTON ROD ASSeMblY
PISTON ReTAINeR
eND PlUG ASSeMblY
INJeCTOR MOUNTING SCReW
bYPASS ADAPTeR (AUTOMATICS ONlY)
bYPASS ADAPTeR O-RING

ADAPTeR ClIP SCReW 8-18 X 5/8"
DRAIN O-RING
INJeCTOR O-RING
bRINe SPACeR O-RING
INJeCTOR COVeR O-RING
INJeCTOR bODY
INJeCTOR SCReeN
INJeCTOR COVeR
bRINe VAlVe STeM ONlY
bRINe VAlVe ASSY. - INCl. 27 TO 34
bRINe VAlVe SeAT
bRINe VAlVe CAP
bRINe VAlVe SPACeR
QUAD RING
bRINe VAlVe SPRING
bRINe VAlVe WASHeR
ReTAINING RING
bRINe lINe COMPReSSION NUT
bRINe lINe FeRRUle
bRINe lINe bRASS INSeRT
blFC bUTTON .5 GPM
bRINe lINe O-RING
blFC bUTTON ReTAINeR
blFC bRASS FITTING
QTY.
1
2
5
1
1
1
4
1
1
1
1
1
1
1
2
2
4
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ReF.
NO.
PART
NO.
42 20251X266
20251X267
20251X268
20251X269
20251X270
20251X271
20251X272
20251X274
43 20561X246
46 20561X248
47 20561X249
48 20561X250
49 20561X251
50 20251X406
51 20561X260
DeSCRIPTION
FlOW CONTROl bUTTON 3.0 PM
DlFC bUTTON ReTAINeR
AIR DISPeRSeR
eND PlUG ReTAINeR
10-24 X 1/2" SCReW
WASHeR
6-32 X 1/2" SCReW
INJeCTOR MODel ASSY. # 1 INJ, .5
blFC, SPeCIFY DlFC. INCl. (2) #14,
(1) #18, (2) #19 & #20, (1) eA. #21 THRU
#27, (1) eA. #28 THRU #43
QTY.
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
FIlTeR COMPONeNTS NOT SHOWN

Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
20562X263 FIlTeR MODUle ASSY. SPeCIFY DlFC

20561X256 DRAIN lINe FITTING STRAIGHT 1/2"
NPT X 1/2" TUbING
20251X255 DRAIN lINe FITTING 90 elbOW
1/2" NPT X 1/2" TUbING
20562X102 bRINe VAlVe PlUG - FIlTeR ONlY
20561X220 bRINe VAlVe PlUG O-RING
20562X103 blFC PlUG - FIlTeR ONlY
20561X239 blFC PlUG O-RING
20562X254 PISTON ASSY. - FIlTeR ONlY
INJeCTOR NOZZle UNDRIlleD

1
1
1
1
1
1
1
1
1
PARTS
25
26
27
27A
28
29
30
31
32
33
34
35
36
37
38
39
40
41
20561X209
20561X210
20561X211
20561X212
20561X214
20561X215
20561X216
20561X217
20561X218
20561X219
20561X220
20561X221
20561X222
20251X205
20251X241
20251X235
20251X206
20251X242
20251X236
20251X204
20561X226
N/S
20561X225
20251X315
N/S
N/S
20251X312
N/S
N/S
N/S
20251X304
20251X305
20251X303
20251X318
20561X239
20561X240
20561X241
DeSCRIPTION
- 156 -
PARTS
Parts Diagram - 5600 Clock Regeneration Powerhead
- 157 -
Parts list - 5600 Clock Regeneration Powerhead
ReF.
NO.
0
1
2
3
4
5
6
7
8
9
NOT
SHOWN
11
12
13
14
15
16
NOT
SHOWN
NOT
SHOWN
19
20
21
22
23
25
26
27
28
29
30
34
35
NOT
SHOWN
37
38
39
DeSCRIPTION
20561X100 5600 12 DAY SOFTeNeR POWeRHeAD

ASSY. COMPleTe
20561X101 DRIVe HOUSING
20251X425 MOTOR, 110 V / 60 HZ
20251X427 MOTOR MOUNT AND GROUND SCReW
20251X406 COMPONeNT MOUNTING SCReW
20251X419 IDleR PINION
20561X111 MAIN GeAR AND SHAFT
20561X114 MANUAl ReGeNeRATION KNOb
20251X413 bAll, 1/4" DIA. SST
20251X412 SKIPPeR WHeel DeTeNT SPRING
20251X404 24 HOUR lAbel
N/S
SKIPPeR WHeel lAbel
20251X408 SKIPPeR WHeel ASSY. - 12 DAY
20251X435 SKIPPeR WHeel RING
20251X414 MAIN GeAR DeTeNT SPRING
20251X410 ReGeN POINTeR
20561X126 bACK COVeR
20561X127 FRONT lAbel - blUe / SIlVeR
N/S
ReAR lAbel
20561X129 blUe TAPe STRIPe
20561X130 bRINe CAM ASSY. 6-36
N/S
TIMe FIll CAM SCReW
N/S
TIMe FIll CAM NUT
N/S
TIMe FIll CAM
20561X134 DRIVe MOUNTING SCReW
20561X135 WASHeR
N/S
"lbS. OF SAlT" lAbel
20561X137 KNOb SCReW
20561X138 VAlVe POSITION DIAl
N/S
VAlVe POSITION DIAl - FIlTeR ONlY
20561X139 SIlVeR KNOb lAbel
20561X125 DeSIGNeR COVeR - 5600
QTY.
1
1
1
1
3
6
1
1
1
1
1
1
1
1
1
4
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
PARTS
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
PART
NO.

- 158 -
PARTS
Parts Diagram-5600 econominder Meter Regeneration Powerhead
- 159 -
Parts list - 5600 econominder Meter Regeneration Powerhead
ReF.
NO.
0
1
2
3
4
5
6
7
8
9
NOT
SHOWN
11
12
13
14
15
16
NOT
SHOWN
18
19
20
21
22
24
25
27
28
29
30
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
NOT
SHOWN
37
38
39
40
41
42
43
44
NOT
SHOWN
DeSCRIPTION
20563X100 5600 MeTeR SOFTeNeR POWeRHeAD

ASSY. COMPleTe
20563X101 DRIVe HOUSING
20251X425 MOTOR, 110 V / 60 HZ
20251X427 MOTOR MOUNT AND GROUND SCReW
20251X406 COMPONeNT MOUNTING SCReW
20251X419 IDleR PINION
20561X111 MAIN GeAR AND SHAFT
20561X114 MANUAl ReGeNeRATION KNOb
20251X413 bAll, 1/4" DIA. SST
20251X414 SPRING DeTeNT
20251X404 24 HOUR lAbel
20253X108 PROGRAM WHeel SCReW
20563X119 PROGRAM WHeel ASSY - SPeCIFY K
20253X111 PROGRAM WHeel ReTAINeR
20563X121 PROGRAM WHeel COVeR lAbel
20561X126 bACK COVeR
20563X127 SIlVeR FRONT lAbel
N/S
ReAR lAbel
20561X129 SIlVeR TAPe STRIPe
20561X130 bRINe CAM ASSeMblY 6-36
N/S
TIMe FIll CAM SCReW
N/S
TIMe FIll CAM NUT
N/S
TIMe FIll CAM
20561X134 DRIVe MOUNTING SCReW
20561X135 WASHeR
N/S
"lbS. OF SAlT" lAbel
20563X137 PROGRAM WHeel DRIVe PINION
20563X138 DRIVe PINION ClUTCH
20563X139 SPRING ReTAINeR
20563X140 SPRING
20563X141 CAble ASSY. STANDARD 8.25"
20563X142 CAble ASSY. eXT. 6.75"
20561X138 VAlVe POSITION DIAl STANDARD
20561X139 SIlVeR KNOb lAbel
20561X137 KNOb SCReW
20561X125 DeSIGNeR COVeR - 5600
QTY.
1
1
1
1
3
5
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
PARTS
34
35
PART
NO.

- 160 -
PARTS
Parts Diagram - 5600SXT Control Valve Assembly
- 161 -
Parts list - 5600SXT Control Valve Assembly
ReF.
NO.
PART
NO.
0
1
2
3
4
5
7
7A
8
20564X000
20561X201
20561X202
20561X203
20561X204
20561X205
20561X207
20561X253
20564X208
8A 20564X254
9
10
11
12
14
15
16
17
18
19
20
21
22
23
24
VAlVe bODY COMPleTe

ADAPTeR ClIP
SeAl
VAlVe bODY ONlY 1.05" DIST.
DIST. TUbe O-RING 1.05" O.D.
VAlVe TO TANK O-RING
SPACeR
SeAl & SPACeR KIT INCl. 5 - #2 & 4 - #7
PISTON ONlY
PISTON & eND PlUG ASSY. INCl. #8,
9, 10, 11 & 12
PISTON PIN
PISTON ROD ASSeMblY
PISTON ReTAINeR
eND PlUG ASSeMblY
INJeCTOR MOUNTING SCReW
bYPASS ADAPTeR (AUTOMATICS ONlY)
bYPASS ADAPTeR O-RING

ADAPTeR ClIP SCReW 8-18 X 5/8"
DRAIN O-RING
INJeCTOR O-RING
bRINe SPACeR O-RING
INJeCTOR COVeR O-RING
INJeCTOR bODY
INJeCTOR SCReeN
INJeCTOR COVeR
bRINe VAlVe STeM ONlY
bRINe VAlVe ASSY. - INCl. 27 TO 34
bRINe VAlVe SeAT
bRINe VAlVe CAP
bRINe VAlVe SPACeR
QUAD RING
bRINe VAlVe SPRING
bRINe VAlVe WASHeR
ReTAINING RING
bRINe lINe COMPReSSION NUT
bRINe lINe FeRRUle
bRINe lINe bRASS INSeRT
blFC bUTTON .5 GPM
bRINe lINe O-RING
blFC bRASS FITTING
QTY.
1
2
5
1
1
1
4
1
1
1
1
1
1
1
2
2
4
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ReF.
NO.
PART
NO.
42 20251X266
20251X267
20251X268
20251X269
20251X270
20251X271
20251X272
20251X274
43 20561X246
46 20561X248
47 20561X249
48 20561X250
49 20561X251
50 20251X406
51 20561X260
DeSCRIPTION
FlOW CONTROl bUTTON 3.0 PM
AIR DISPeRSeR
eND PlUG ReTAINeR
10-24 X 1/2" SCReW
WASHeR
6-32 X 1/2" SCReW
INJeCTOR MODel ASSY. # 1 INJ, .5
blFC, SPeCIFY DlFC. INCl. (2) #14,
(1) #18, (2) #19 & #20, (1) eA. #21 THRU
#27, (1) eA. #28 THRU #43
QTY.
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1

PARTS
25
26
27
27A
28
29
30
31
32
33
34
35
36
37
38
39
40
41
20564X209
20564X210
20561X211
20564X212
20561X214
20251X215
20561X216
20561X217
20561X218
20561X219
20561X220
20561X221
20561X222
20251X205
20251X241
20251X235
20251X206
20251X242
20251X236
20251X204
20561X226
N/S
20561X225
20251X315
N/S
N/S
20251X312
N/S
N/S
N/S
20251X304
20251X305
20251X303
20251X318
20561X239
20561X240
20561X241
DeSCRIPTION
- 162 -
PARTS
Parts Diagram - 5600SXT Valve Powerhead Assembly
- 163 -
Parts Diagram - 5600SXT Valve Powerhead Assembly
ReF.
NO.
PART
NO.
DeSCRIPTION
20564X100 5600Se POWeRHeAD ASSY.

COMPleTe
1 20564X101 DRIVe HOUSING
2 20561X134 DRIVe MOUNT SCReW
3 20564X103 POWeR WIRe HARNeSS
4 20251X423 SPRING WASHeR
5 20251X421 IDleR GeAR
6 20564X106 DeTeNT SPRING
7 20561X102 MOTOR MOUNTING PlATe
8 20251X406 COMPONeNT SCReW
9 20564X107 DRIVe MOTOR 2 RPM 24 V 50 / 60 HZ
10 20251X427 MOTOR SCReW
11 20564X116 bRINe VAlVe CAM
12 20251X135 WASHeR
13 20564X128 SCReW
14 20564X109 DRIVe GeAR
15 20251X413 DeTeNT bAll
16 20564X108 Main Drive Gear & Shaft-Downflow-black
17 20251X102 STRAIN RelIeF
18 20564X117 24 V 9.6 VA TRANSFORMeR (OPTIONAl)
19 20561X126 bACK PlATe
20 20564X119 FRICTION WASHeR
21 20564X110 CYCle CAM (DOWNFlOW bRINe - blACK)
22 20561X137 CYCle CAM SCReW
23 20251X113 MICROSWITCH
24 20251X114 INSUlATOR
25 20564X122 MICROSWITCH SCReW
26A 20564X104 FRONT PANel ASSY. (b/W FIRST lAbel)
26b 20564X105 FRONT PANel ASSY. (b/W FIRST lAbel)
27 20564X124 FRONT PANel SCReW
QTY.
1
1
2
1
1
1
2
1
4
1
3
1
1
2
1
2
1
1
1
1
1
1
1
2
1
2
1
1
2
PARTS

- 164 -
Parts Diagram - 3/4 Turbine Meter Assembly
PARTS
1A
ReF.
NO.
1A
PART
NO.
DeSCRIPTION
20564X200 Meter Assembly, Turbine Complete
QTY.
1
- 165 -
Parts Diagram - Plastic bypass Valve
3
2
1
2
PART
NO.
20561X292
20561X290
20561X291
3 20561X288
20561X289
4 20561X296
DeSCRIPTION
Plastic bypass Valve Assembly
3/4 Yoke - Stainless Steel
1 Yoke - Stainless Steel
3/4 Yoke - Plastic
1 Yoke - Plastic
Adapter Coupling Assembly 90
QTY.
PARTS
ReF.
NO.
1
1
1
1
1
1
- 166 -
Parts Diagram - brass bypass Valve Assembly
PARTS
Parts List
Ref. No.
1
Quantity
1
1
Part No.
20561X270
20561X283
Description
bypass Valve 3/4 Stainless Steel
bypass Valve 1 Stainless Steel
- 167 -
Parts Diagram - 9000 econominder Second Tank Adapter
ReF. PART
NO. NO.
1
N/S
2 20561X216
3 20908X115
4 20561X205
5
N/S
6 20561X201
7
N/S
8 20908X215
9 20908X218
DeSCRIPTION
SeCOND TANK ADAPTeR
O-RING
O-RING
O-RING
YOKe
HOlD DOWN ClIP
8-32 X 3/8" HeX WSHR HD SCReW
COUPlING
INTeRCONNeCT PIPeS - SPeCIFY TANK SIZe
QTY.
1
8
1
1
2
4
4
4
2
PARTS
- 168 -
PARTS
Parts Diagram - 9000 econominder Timer Assembly
- 169 -
Parts list - 9000 econominder Timer Assembly

PART
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
36
37
38
39
40
41
N/S
N/S
N/S
N/S
N/S
N/S
20908X114
N/S
20908X113
N/S
N/S
N/S
N/S
N/S
20253X111
20253X108
20251X407
N/S
20251X405
20251X406
N/S
N/S
N/S
20563X140
20563X139
20251X429
20908X201
20251X431
20251X432
20251X419
N/S
20251X421
20251X422
20251X424
20251X425
20251X426
20251X411
N/S
N/S
20251X417
N/S
NOT
SHOWN
DeSCRIPTION
TIMeR HOUSING ASSY.
CAPACITY GAllONS lAbel
CAUTION lAbel
INSTRUCTION lAbel
ACTUATOR PlATe
# 8 HeX WASHeR HD SCReW
SPRING ClIP
# 4 PlAIN WASHeR
SPRING
PROGRAM WHeel DRIVe GeAR
3/4" MeTeR GAllON lAbel
ADJUSTING DISC
PROGRAM WHeel COVeR
4 - 40 FIll HD SCReW STNlS SCReW
PROGRAM WHeel ReTAINeR
6-20 X 1/2" FlT HD ST SCReW
bUTTON DeCAl
CYCle ACTUATOR GeAR
KNOb
6-20 X 1/2" HeX WASHeR HD SCReW
5-20 X 3/8" SlT RD HD MACH SCReW
DRIVe PINION
DRIVe PINION ClUTCH
MeTeR ClUTCH SPRING
ReTAINeR
INSUlATOR
SWITCH
SWITCH
4-40 X 1/8" PAN HD MACH SCReW
IDleR SHAFT
IDleR SHAFT SPRING
IDleR GeAR
DRIVe GeAR
MOTOR MOUNTING PlATe
MOTOR - 120 V 60 Hz - 1/30 RPM
6-32 X 1/8" FIl HD MACH SCReW
SPRING ClIP
MAIN DRIVe GeAR
PROGRAM WHeel ASSY.
ROll PIN
6 X 1/4" HeX WASHeR HD SCReW
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
4
2
1
1
1
1
3
1
1
2
1
1
1
1
1
1
2
1
1
1
20
1
PARTS
ReF.
NO.
- 170 -
PARTS
Parts Diagram - 9000 econominder Drive Assembly
- 171 -
Parts list - 9000 econominder Drive Assembly

PART
NO.
0
1
2
3
4
5
6
7
8
9
10
11
12
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
20908X200
N/S
N/S
20561X251
N/S
N/S
N/S
N/S
20251X101
N/S
20908X203
20908X204
20908X205
N/S
N/S
N/S
N/S
N/S
20251X426
20908X206
N/S
N/S
N/S
20251X113
N/S
N/S
20908X207
N/S
20251X102
N/S
N/S
N/S
N/S
20908X209
20908X208
N/S
20251X114
20908X210
N/S
N/S
NOT
SHOWN
32
33
34
35
36
NOT
SHOWN
39
NOT
SHOWN
NOT
SHOWN
DeSCRIPTION
9000 TIMeR ASSY. 1/30 RPM
4-40 X 3/16 SCReW
6-20 HeX WASHeR HD SCReW
WASHeR
UPPeR PISTON ROD lINK
lOWeR PISTON ROD lINK
8-32 "U" TYPe NUT ClIP
TIMeR WIRING HARNeSS
POWeR CORD
DRIVe WIRING HARNeSS
lOWeR DRIVe GeAR ASSY.
DRIVe GeAR
GeNeVA WHeel
COVeR SCReW ASSY.
POSITION DeCAl
ReTAINING RING
GROUND PlATe
6 X 1/4" HeX WASHeR SCReW
6-32 X 1/4 RD HD SCReW
DRIVe MOTOR KIT 110 V - 60 Hz
CONTROl PANel
4-40 X 1-3/8" F H MACH SCReW
# 4 lOCK WASHeR
MICRO SWITCH
4-40 HeX NUT
10-24 X 3/4 HeX WASHeR HeAD SCReW
UPPeR DRIVe GeAR ASSY.
TRIPle CAM
STRAIN RelIeF
DRIVe GeAR ReTAINING RING
UPPeR PISTON ROD lINK GUIDe PIN
CAble GUIDe
THRUST WASHeR
MeTeR CAble ASSY. 1" MeTeR
MeTeR CAble ASSY. 3/4" MeTeR
SPACeR
INSUlATOR
PROGRAM MICRO SWITCH
TOP COVeR
bOTTOM COVeR
QTY.
1
2
2
2
1
1
2
1
1
1
1
1
1
2
1
1
1
1
2
1
1
2
2
1
2
7
1
1
1
1
1
1
2
1
1
2
1
1
1
1
PARTS
ReF.
NO.

- 172 -
PARTS
Parts Diagram - 9000 econominder Valve Assembly
- 173 -
Parts list - 9000 econominder Valve Assembly
ReF.
NO.
PART
NO.
1
2
3
4
5
N/S
N/S
20251X218
N/S
20561X212
20908X212
5A
6
7
20561X207
20561X202
7A 20561X253
8
9
N/S
N/S
20908X213
9A
9b
20908X211
10
11
12
13
14
15
16
17
18
19
20
20908X115
20561X205
N/S
N/S
N/S
N/S
20561X220
20251X312
N/S
N/S
20251X315
20A 20908X116
21
22
23
VAlVe bODY ONlY

UPPeR PISTON
PISTON ROD ReTAINeR
UPPeR PISTON ROD
eND PlUG ASSY.
UPPeR PISTON ASSY. INCl. (1) eA. # 2
THRU # 5 PlUS SCReW & lINK
SPACeR
SeAl
SeAl & SPACeR KIT UPPeR INCl.
(5) # 7 AND (4) # 6
lOWeR PISTON ROD
lOWeR PISTON
lOWeR PISTON ASSY. INCl. (1) each
# 3, 5, 8 & 9 PlUS SCReW & lINK
lOWeR SeAl & SPACeR KIT INCl.
(11) # 7, (8) # 6 & (1) # 26
O RING
O-RING
ReTAINING RING
NYlON bRINe VAlVe WASHeR
bRINe VAlVe SPRING
bRINe VAlVe CAP
O-RING
QUAD RING
bRINe VAlVe SPACeR
bRINe VAlVe STeM
bRINe VAlVe SeAT
bRINe ASSY. INCl. (1) eA. # 12 THRU
# 15, (2) eA. # 16, (1) eA. # 17 THRU # 20
INJeCTOR bODY
O-RING
INJeCTOR COVeR
SPACeR
10-24 X 1-3/4 HeX HD MACH SCReW
INJeCTOR SPACeR
O-RING
AIR DISPeRSeR
O-RING
INJeCTOR SCReeN
blFC FITTING
.5 GPM blFC bUTTON
O-RING
QTY.
1
1
2
1
2
1
12
16
1
1
1
1
ReF.
NO.
DeSCRIPTION
38 20251X266
20251X267
20251X268
20251X269
20251X270
20251X271
20251X272
39 20561X246
40 20251X303
41 20251X305
42 20251X304
20908X214
42A
1
1
1
1
1
1
1
3
1
1
1
1
1
PART
NO.
43
44
45
47
48

3/8" TUbe INSeRT
3/8" FeRRUle
3/8" TUbe NUT
INJeCTOR/DRAIN ASSY. INCl. (1) each
# 20A, # 21 THRU # 27, (2) # 29 & (1)
each # 30 THRU # 42 - .5 blFC & NO. 1
INJeCTOR/THROAT FURNISHeD
SPeCIFY DlFC ReQUIReD
N/S
STUb eND PlUG
N/S
eND PlATe
N/S
10-24 X 3/8" HeX WASHeR HD SCReW
N/S
bRINe VAlVe STAND OFF
20561X214 10-24 X 1-3/16" HeX WSHR HD SCReW
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1

1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
PARTS
24
25
26
27
28
29
30
31
32
34
35
36
37
N/S
20251X206
20251X242
20251X205
20251X241
20561X221
20561X226
N/S
N/S
N/S
20561X219
20561X248
N/S
20561X204
20561X241
20251X318
20561X240
20561X239
DeSCRIPTION
- 174 -
Parts Diagram - R/O

ReF.
NO.
1
2
3
4A
4
5
6
7
8
9
10
11
PART
NO.
57100X096
57100X097
57100X098
57100X100
N/S
N/S
N/S
N/S
57100X106
57100X104
57100X105
PRe - GAC
PRe - SeD
12 MM -TFC
MM - CTA
13 57100X111
14 57100X108
15
N/S
16 57100X107
17 57100X103
18
N/S
19 PST - GAC
21 57100X102
22
N/S
DeSCRIPTION
Auto. Shut Off Screws
Auto. Shut Off Cap
Auto. Shut Off Cap O-Ring
Auto. Shut Off Repair Kit (Includes: 4 - 7)
Auto. Shut Off Diaphragm - large
Auto. Shut Off Piston
Auto. Shut Off Piston Ring
Auto. Shut Off Diaphragm - Small
Manifold Plate
Duckbill Check Valve 1/8
Duckbill Check Valve Retainer
Sediment/Carbon Cartridge -TFC Models
Sediment Filter Cartridge - CTA Models
T.F.C. R.O. Membrane (50 GPD)
C.T.A. R.O. Membrane (14 GPD)
Sump O-Ring
Sump
1/4 Plug
3/8 Union elbow
Drain Restrictor (Specify CTA or TFC)
Cover
Activated Carbon Post Filter Cartridge
Wrench for Sumps
1/4 - 3/8 Fitting Wrench
QTY.
ReF.
NO.
PART
NO.
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
Not
Shown
57100X112
57100X113
57011X102
57100X115
57005X100
57005X101
RO-100-C
DeSCRIPTION
Drain Clamp 3/8
Self Piercing Saddle Valve Tap 1/4
Tank Shut Off 3/8
Tank R/O - 3.0 Gallon Capacity
R/O Faucet 3/8 long Reach Non Air Gap
R/O Faucet 3/8 long Reach Air Gap
1/4 R.O. Tubing - Clear 100 Rolls
PARTS

- 175 -
QTY.
1
1
1
1
1
1
1

CSI Water Catalog 2013

Uploaded by

Copyright:

Available Formats

CSI Water Catalog 2013

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CSI Water Catalog 2013

Uploaded by

Copyright:

Available Formats

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.

qxd 6/17/13 4:19 PM Page i

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page ii

II. PRODUCTS SECTION

Project Data Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page iii

V. PARTS LISTS & DIAgRAMS

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 1

CONTACTING CSI WATeR TReATMeNT

Telephone & Fax Numbers

Internet Web Address

general Email Address

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 2

VISITING OUR FACIlITY

If your plans require an overnight in Ashland, we have a few different options.

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 3

CSI WATeR TReATMeNT COMPANY PROFIle

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 4

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 5

Cabinet & Two Tank Water Softeners - Signature Valve

Save Soap, Appliances,

rock! Calcium and Magnesium can

water tanks, and cause laundry to come

Water Heater Fuel Savings

Personal Care Items 25%

ucts compared to soft water.

Appliance Savings 25%

can use twice the amount of soaps,

and can give skin and hair a silky look

and cost to heat hard water, plus you

Soap / Chemical Savings 70%

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:19 PM Page 6

Cabinet & Two Tank Water Softeners - Signature Valve

Maximum Raw Water

Maximum Clear Iron /

exchange Resin (cu ft.)

Mineral Tank (polyglass)

brine Tank (polyethylene

Service Flow Rate (gpm)*

backwash Flow Rate (gpm)

Backwash Flow Rate (gpm)

18x26x53 18x27x56 18x28x62 18x30x60 18x32x74 24x40x74

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:20 PM Page 7

Signature Series Duplex Softeners

Maximum Raw Water Hardness (grains)

Maximum Clear Iron/Manganese (ppm)

exchange Resin (cu. ft.) (per tank)

Gravel Underbedding (per tank)

Mineral Tanks (polyglass)

brine Tank (polyethylene with grid & safety)

Service Flow Rate (gpm per active tank)*

backwash Flow Rate (gpm)

Backwash Flow Rate (gpm) Vortech (V) Units

gallons Used/Regeneration Vortech (V) Units

Approximate Shipping Weight (pounds)

CSI_WaterTreatmentCatalog_2013_REV_CSIWaterTreatment#132FF.qxd 6/17/13 4:20 PM Page 8

The TerminatR Water Treatment System - Signature Valve

Save Soap, Appliances,

water, plus you can use twice the amount

ed products compared to soft water.