9.14.5. Recommended Partitioning Scheme 9.14.5.1.

x86, AMD64, and Intel 64 systems Unless you have a reason for doing otherwise, we recommend that you create the following partitions for x86, AMD64, and Intel 64 systems:

A swap partition A /boot partition A / partition A swap partition (at least 256 MB) swap partitions are used to support virtual memory. In other words, data is written to a swap partition when there is not enough RAM to store the data your system is processing. In years past, the recommended amount of swap space increased linearly with the amount of RAM in the system. But because the amount of memory in modern systems has increased into the hundreds of gigabytes, it is now recognized that the amount of swap space that a system needs is a function of the memory workload running on that system. Swap space is usually designated during installation, but determining the memory workload of a system at this point can be difficult. During a kickstart installation, you can request that the amount of swap space be set automatically (refer to Section 32.4, Kickstart Options. However, this setting is not precisely calibrated for your system, so use the following table if you require the amount of swap space to be set more precisely. Table 9.2. Recommended System Swap Space Amount of RAM in the System 4GB of RAM or less 4GB to 16GB of RAM 16GB to 64GB of RAM 64GB to 256GB of RAM Recommended Amount of Swap Space a minimum of 2GB of swap space a minimum of 4GB of swap space a minimum of 8GB of swap space a minimum of 16GB of swap space

Amount of RAM in the System Recommended Amount of Swap Space 256GB to 512GB of RAM a minimum of 32GB of swap space

Note that you can obtain better performance by distributing swap space over multiple storage devices, particularly on systems with fast drives, controllers, and interfaces.

A /boot/ partition (250 MB) The partition mounted on /boot/ contains the operating system kernel (which allows your system to boot Red Hat Enterprise Linux), along with files used during the bootstrap process. For most users, a 250 MB boot partition is sufficient. Important Supported file systems The GRUB bootloader in Red Hat Enterprise Linux 6 supports only the ext2, ext3, and ext4 (recommended) file systems. You cannot use any other file system for /boot, such as Btrfs, XFS, or VFAT. Note If your hard drive is more than 1024 cylinders (and your system was manufactured more than two years ago), you may need to create a /boot/ partition if you want the / (root) partition to use all of the remaining space on your hard drive. Note If you have a RAID card, be aware that some BIOSes do not support booting from the RAID card. In cases such as these, the /boot/ partition must be created on a partition outside of the RAID array, such as on a separate hard drive.

A root partition (3.0 GB - 5.0 GB) This is where "/" (the root directory) is located. In this setup, all files (except those stored in /boot) are on the root partition.

A 3.0 GB partition allows you to install a minimal installation, while a 5.0 GB root partition lets you perform a full installation, choosing all package groups. Root and /root The / (or root) partition is the top of the directory structure. The /root directory/root (sometimes pronounced "slash-root") directory is the home directory of the user account for system administration. Many systems have more partitions than the minimum listed above. Choose partitions based on your particular system needs. For example, consider creating a separate /home partition on systems that store user data. Refer to Section 9.14.5.1.1, Advice on Partitions for more information. If you create many partitions instead of one large / partition, upgrades become easier. Refer to the description of the Edit option in Section 9.14, Creating a Custom Layout or Modifying the Default Layout for more information. The following table summarizes minimum partition sizes for the partitions containing the listed directories. You do not have to make a separate partition for each of these directories. For instance, if the partition containing /foo must be at least 500 MB, and you do not make a separate /foo partition, then the / (root) partition must be at least 500 MB. Table 9.3. Minimum partition sizes Directory / /usr /tmp /var /home /boot Minimum size 250 MB 250 MB, but avoid placing this on a separate partition 50 MB 384 MB 100 MB 250 MB

Leave Excess Capacity Unallocated Only assign storage capacity to those partitions you require immediately. You may allocate free space at any time, to meet needs as they occur. To learn about a more

flexible method for storage management, refer to Appendix D, Understanding LVM. If you are not sure how best to configure the partitions for your computer, accept the default partition layout. 9.14.5.1.1. Advice on Partitions Optimal partition setup depends on the usage for the Linux system in question. The following tips may help you decide how to allocate your disk space.

If you expect that you or other users will store data on the system, create a separate partition for the /home directory within a volume group. With a separate /home partition, you may upgrade or reinstall Red Hat Enterprise Linux without erasing user data files. Consider encrypting any partitions that might contain sensitive data. Encryption prevents unauthorized people from accessing the data on the partitions, even if they have access to the physical storage device. In most cases, you should at least encrypt the /home partition. Each kernel installed on your system requires approximately 10 MB on the /boot partition. Unless you plan to install a great many kernels, the default partition size of 250 MB for /boot should suffice. Important Supported file systems The GRUB bootloader in Red Hat Enterprise Linux 6 supports only the ext2, ext3, and ext4 (recommended) file systems. You cannot use any other file system for /boot, such as Btrfs, XFS, or VFAT.

The /var directory holds content for a number of applications, including the Apache web server. It also is used to store downloaded update packages on a temporary basis. Ensure that the partition containing the /var directory has enough space to download pending updates and hold your other content. Warning The PackageKit update software downloads updated packages to /var/cache/yum/ by default. If you partition the system manually, and create a separate /var/ partition, be sure to create the partition large enough (3.0 GB or more) to download package updates.

The /usr directory holds the majority of software content on a Red Hat Enterprise Linux system. For an installation of the default set of software, allocate at least 4 GB of space. If you are a software developer or plan to use your Red Hat Enterprise Linux system to learn software development skills, you may want to at least double this allocation. Do not place /usr on a separate file system If /usr is on a separate file system from /, the boot process becomes much more complex because /usr contains boot-critical components. In some situations (like installations on iSCSI drives), the boot process might not work at all.

Consider leaving a portion of the space in an LVM volume group unallocated. This unallocated space gives you flexibility if your space requirements change but you do not wish to remove data from other partitions to reallocate storage. If you separate subdirectories into partitions, you can retain content in those subdirectories if you decide to install a new version of Red Hat Enterprise Linux over your current system. For instance, if you intend to run a MySQL database in /var/lib/mysql, make a separate partition for that directory in case you need to reinstall later.

The following table is a possible partition setup for a system with a single, new 80 GB hard disk and 1 GB of RAM. Note that approximately 10 GB of the volume group is unallocated to allow for future growth. Example Usage This setup is not optimal for all use cases. Example 9.1. Example partition setup Table 9.4. Example partition setup Partition /boot swap Size and type 250 MB ext3 partition

2 GB swap LVM physical volume Remaining space, as one LVM volume group

The physical volume is assigned to the default volume group and divided into the following logical volumes: Table 9.5. Example partition setup: LVM physical volume Partition / /var /home Size and type 13 GB ext4 4 GB ext4 50 GB ext4

Prev9.14.4. Create LVM Logical Volume Up Home