MOPSlcd6

Technical Manual Rev. 4.0

Kontron Embedded Modules GmbH

Brunnwiesenstrae 16 94469 Deggendorf/ Germany
p588m140.doc Kontron Embedded Modules GmbH Page: 1 of 44

MOPSlcd6

Table of Contents

1. TABLE OF CONTENTS
1. 2. TABLE OF CONTENTS ......................................................................................................................................... 2 USER INFORMATION ........................................................................................................................................... 4 2.1 2.2 2.3 2.4 2.5 2.6 3. 4. 5. 6. 7. 8. About This Manual .................................................................................................................................. 4 Copyright Notice ..................................................................................................................................... 4 Trademarks.............................................................................................................................................. 4 Standards................................................................................................................................................. 4 Warranty................................................................................................................................................... 4 Technical Support................................................................................................................................... 5

INTRODUCTION ................................................................................................................................................... 6 FEATURES ......................................................................................................................................................... 7 I/O MAP ............................................................................................................................................................ 8 BLOCK DIAGRAM ................................................................................................................................................ 9 CONNECTOR ARRANGEMENT ............................................................................................................................ 10 BIOS-DESCRIPTION ......................................................................................................................................... 11 8.1 8.2 8.3 8.4 The Setup Guide.................................................................................................................................... 11 Boot Utilities .......................................................................................................................................... 21 BIOS Update with Phoenix Phlash ...................................................................................................... 22 Boot Block Support .............................................................................................................................. 23 ALI-Chipset Features............................................................................................................................ 24 Memory configuration .......................................................................................................................... 24 Interrupts ............................................................................................................................................... 24 ISA DMA ................................................................................................................................................. 25 Onboard VGA 69000 ............................................................................................................................. 26 Watchdog Extension ............................................................................................................................ 28

9.

HARDWARE DESCRIPTION................................................................................................................................. 24 9.1 9.2 9.3 9.4 9.5 9.6

10. THE JIDA STANDARD ....................................................................................................................................... 30 11. NETWORK OPERATION ..................................................................................................................................... 33 11.1 11.2 11.3 11.4 12.1 12.2 12.3 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 Overview ............................................................................................................................................ 33 Configuration 82551ER .................................................................................................................... 33 Software and driver setup................................................................................................................ 34 Ethernet Technical Support ............................................................................................................. 34 Mechanical Specifications ............................................................................................................... 35 Electrical Specifications................................................................................................................... 35 Environmental Specifications.......................................................................................................... 35 Keyboard, Reset, Battery, Speaker ................................................................................................. 36 Serial Port COM A, B RS232C.......................................................................................................... 37 Parallel Port LPT 1 ............................................................................................................................ 38 Floppy Connector ............................................................................................................................. 38 IDE Connector for 2,5" Hard Disk.................................................................................................... 39 Ethernet Connector .......................................................................................................................... 39 CRT Connector.................................................................................................................................. 39 USB Connector.................................................................................................................................. 40 Power Connector .............................................................................................................................. 40

12. SPECIFICATIONS............................................................................................................................................... 35

13. PERIPHERAL INTERFACE ................................................................................................................................... 36

14. LITERATURE, STANDARDS, LINKS ..................................................................................................................... 41

p588m140.doc Kontron Embedded Modules GmbH Page: 2 of 44

MOPSlcd6 14.1 14.2 14.3 14.4

Table of Contents Buses ................................................................................................................................................. 41 General PC Architecture .................................................................................................................. 42 Ports ................................................................................................................................................... 42 Programming..................................................................................................................................... 43

15. DOCUMENT REVISION HISTORY......................................................................................................................... 44

p588m140.doc

Kontron Embedded Modules GmbH

Page: 3 of 44

MOPSlcd6

User Information

2. USER INFORMATION
2.1 About This Manual

This document provides information about products from Kontron Embedded Computers AG and/or its subsidiaries. No warranty of suitability, purpose, or fitness is implied. While every attempt has been made to ensure that the information in this document is accurate, the information contained within is supplied as-is and is subject to change without notice. For the circuits, descriptions and tables indicated, Kontron assumes no responsibility as far as patents or other rights of third parties are concerned.

2.2

Copyright Notice

Copyright 2002 Kontron Embedded Computers AG. All rights reserved. No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron.

2.3

Trademarks

The following lists the trademarks of components used in this board. IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corp. Microsoft is a registered trademark of Microsoft Corp. Intel is a registered trademark of Intel Corp. All other products and trademarks mentioned in this manual are trademarks of their respective owners.

2.4

Standards

Kontron Embedded Modules is certified to ISO 9000 standards.

2.5

Warranty

This Kontron Embedded Modules product is warranted against defects in material and workmanship for the warranty period from the date of shipment. During the warranty period, Kontron Embedded Modules will at its discretion decide to repair or replace defective products. Within the warranty period, the repair of products is free of charge as long as warranty conditions are observed. You may receive a bill for test costs if Kontron Embedded Modules finds no fault with the product. You also may receive a bill for repairs if a products warranty has expired. For warranty service or repair, return the product to a Kontron Embedded Modules service facility listed in the Technical Support section of this document. The warranty does not apply to defects resulting from improper or inadequate maintenance or handling by the buyer, unauthorized modification or misuse, operation outside of the products environmental specifications or improper installation or maintenance. Kontron Embedded Modules will not be responsible for any defects or damages to other products not supplied by Kontron Embedded Modules that are caused by a faulty Kontron Embedded Modules product.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 4 of 44

MOPSlcd6

User Information

2.6

Technical Support

Technicians and engineers from Kontron Embedded Modules and/or its subsidiaries are available for technical support. We are committed to making our product easy to use and will help you use our products in your systems. Before contacting Kontron Embedded Modules technical support, please consult our Website www.pc104-mops.com for the latest product documentation, utilities, and drivers. If the information does not help solve the problem, contact your sales channel (your distributor or you Kontron Sales office where you order this board) by email or telephone.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 5 of 44

MOPSlcd6

Introduction

3. INTRODUCTION
The MOPSlcd6 integrates the complete functionality of a pentium motherboard with CPU, SystemBIOS, up to 64 MByte SDRAM, keyboard-controller, real time clock, onboard high-performance PCISVGA with LCD interface and additional peripheral functions like COM1, COM2, LPT1, Floppyinterface, EIDE-harddisk-interface, watchdog and Ethernet access. The system runs with CPU clock speed 166MHz and 266 MHz. This manual is describting the MOPSlcd6 new hardware revision 4. This revision isnt fully compatible to older hardware revision by using a different Ethernet Controller, a new revision of southbridge with integrated watchdog and some smaller changes. Changes are be blue.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 6 of 44

MOPSlcd6

Features

4. FEATURES
Processor Intel Pentium with 166 MHz internal Clock and 32 kByte write-back-Cache or Intel Pentium with 266 MHz internal Clock and 32 kByte write-back-Cache Chipset ALI M1543C B1/M1531 PCI Chipset; extended temperature Power Supply 5V only supply Memory 32 256 MB SDRAM-SODIMM-Module up to 28 mm length Ethernet 100BaseT (Twisted Pair) intel 82551ER Two serial ports, (COM1 and COM2) standard RS232C serial ports with FIFO, 16550 compatible Parallel port, LPT1 With ECP/EPP-support Floppy-interface EIDE-PCI-hard disk-interface PCI Bus Master IDE port (up to 2 IDE Devices) supports PIO Mode 3,4 IDE & ATAPI CD-ROM and UDMA33 supports Kontron CHIPdisk Watchdog 128 KByte FLASH-BIOS (Phoenix) Real Time Clock With external Battery-support Keyboard Controller Onboard Asiliant-VGA 69000 LCD-VGA-Controller with PCI-Bus interface incl. Burst Mode support VGA-CRT and LCD Controller with integral 2 MByte Video RAM Resolution up to 1280x1024 on panel and CRT Color depths up to 16 millions of colors Simultaneous display on CRT and panel True 64-Bit Graphics engine and accelerator Powerful drivers for Win3.11, Win95, NT3.51, NT4.0, OS/2.... plug and play panel interfacing on the upper SO-DIMM-Connector supports almost any type of LCD
p588m140.doc Kontron Embedded Modules GmbH Page: 7 of 44

MOPSlcd6

I/O Map

5. I/O MAP
The I/O-port addresses of the processor module MOPSlcd6 are functionally identical with a standard PC/AT.

I/O Addresses 0000 - 001F 0020 - 003F 0040 0043 0050 - 005F 0060 0064 0061 0070 0070 0071 0080 - 008F 0092 00A0 - 00BF 00C0 - 00DF 00F0 - 00FF 0100 10F 01F0 - 01F8 0200 0207 020C-020D 021F 0274 0275 0278 027F 02B0 - 02DF 02E1 02E2 - 02E3 02E8 - 02EF 02F8 - 02FF 0300 030F 0310 031F 0360 0363 0364 0367 0368 036B 036C 036F 0370 0377 0378 037F 0380 038F 0390 0393 03A0 - 03AF 03B0 - 03BF 03C0 - 03CF 03D0 - 03DF 03E8 - 03EF 03F0 - 03F7 03F8 - 03FF

MOPSlcd6 - onboard X X X X X X X X X X X X X X

X X

X X X X X

Function DMA-Controller 1 Interrupt-Controller 1 Timer Onboard Control Registers Keyboard-controller Port B Register NMI Enable Register Real Time Clock DMA Page Register 74LS612 Port A Register (Fast A20 Gate) Interrupt-Controller 2 DMA-Controller 2 Math-Coprocessor Onboard Control Registers Fixed Disk Game I/O Reserved Reserved Control Register 1 External SSD (Board 0 3) Control Register 1 External SSD (Board 4 7) Parallel Port 2 Alternate Enhanced Graphics Adapter GPIB (adapter 0) Data acquisition (Adapter 0) Serial Port 4 Serial Port 2 Onboard Network (default configuration) Prototype Card PC Network (low Address) Reserved PC Network (high Address) Reserved Config. Space for second SMC Controller Parallel Port 1 SDLC, Bisynchronous 2 Cluster Bisynchronous 1 Monochrom Disp. and Printer Adap. Enhanced Graphic Adapter Color/Graphic Monitor Adapter Serial Port 3 Diskette Controller Serial Port 1

p588m140.doc

Kontron Embedded Modules GmbH

Page: 8 of 44

MOPSlcd6

Block Diagram

6. BLOCK DIAGRAM

C&T PCI VGA

BIOS

RTC LPT1 IO-Controller COM1 COM2

EIDE SDRAM

ALI Chipset

CPU

EthernetController

100/10baseT

PC/104plus -Con.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 9 of 44

MOPSlcd6

Connector Arrangement

7. CONNECTOR ARRANGEMENT

p588m140.doc

Kontron Embedded Modules GmbH

Page: 10 of 44

MOPSlcd6

BIOS-Description

8. BIOS-DESCRIPTION
The MOPS/lcd6 is equipped with a Phoenix BIOS which is located in a Flash EPROM onboard. This device has 8bit wide access. Faster access (16bit) is provided by the shadow RAM feature (default).

8.1

The Setup Guide

With the PhoenixBIOS Setup programm, you can modify BIOS settings and control the special features of the computer. The setup programm uses a number of menus for making changes and turning the special features on or off.

General Information
To start the PhoenixBIOS setup utility press <F2> when the string Press <F2> to enter Setup is displayed during bootup. The Main Menu will be displayed.

The Menu Bar

The Menu Bar at the top of the window lists all the different menus. Use the left/right arrows to make a selection.

The Legend Bar

Use the keys listed in the legend bar on the bottom to make your selection or exit the current menu. The table below describes the legend keys and their alternates: Key <F1> or <Alt-H> <Esc> or Arrow key or Arrow key <Tap> or <Shift-Tap> <Home> or <End> <PgUp> or <PgDn> <F5> or <-> <F6> or <+> or <Space> <F9> <F10> <Enter> <Alt-R> Function General help window Exit this menu Select a different menu Move cursor up and down Cycle cursor up and down Move cursor to top or bottom of current window Move cursor to next or previous page Select the previous value for the current field Select the next value for the current field Load default configuration values for this menu Save and Exit Execute command or select submenu Refresh screen

To select an item, simply use the arrow key to move the cursor to the field you want. Then use the plus and minus keys to select a value for that field. The Save Value commands in the Exit Menu save the values currently displayed in all the menus. To display a sup menu, use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A pointer ( ) marks all sub menus.

The Field Help Window

The help window on the right side of each menu displays the help text for the currntly selected field. It updates as you move the cursor to each field.

The General Help Window

Pressing <F1> or <Alt-F1> on any menu brings up the General Help Window that describes the legend keys and their alternates. Press <Esc> to exit the General Help Window.
p588m140.doc Kontron Embedded Modules GmbH Page: 11 of 44

MOPSlcd6

BIOS-Description

The Main Menu

You can make the following selections on the Main Menu itself. Use the sub menus for other selections. Feature System Time System Date Legacy Diskette A Option HH:MM:SS MM/DD/YYYY 360 kB, 5 1.2 MB, 5 720 kB, 3 1.44/1.25 MB, 3 2.88 MB, 3 Not Installed Disabled See above Disabled autodetected drive autodetected drive sub menu sub menu N/A N/A Description Set the system time. Use <Enter to move to MM or SS. Set the system date. . Use <Enter to move to DD or YYYY. Select the type of floppy disk drive installed in the system.

Legacy Diskette B 8Primary Master 8Primary Slave 8Memory Shadow 8Memory Cache System Memory Extended Memory

See above Displays result of PM autotyping. Displays result of PS autotyping. Opens Memory Shadow Menu Opens Memory Cache Menu Displays amount of conventional memory detected during bootup. Displays amount of extendedmemory detected during bootup.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 12 of 44

MOPSlcd6

BIOS-Description

Selecting one of the Master or Slave sub menus displays a menu like this: Feature Type Option None User Auto CD-ROM Description None = Autotyping is not able to supply the drive type or end user has selected None, disabling any drive that may be installed. User = End user supplies the hdd information. Auto = Autotyping, the drive itself supplies the information. CD-RO = CD-ROM drive. Number of cylinders. Number of read/write heads. Number of sectors per track. Displays the calculated size of the drive in CHS Total number of sectors in LBA mode Displays the calculated size of the drive in LBA Any selection except Disabled determines the number of sectors transferred per block. Standard is 1 sector per block. Enabling LBA causes Logical Block Addressing to be used in place of CHS. Enables 32-bit communication between CPU and IDE card. Requires PCI or Local Bus. Selects the method for transferring the data between the hard disk and system memory.

Cylinders Heads Sectors Maximum Capacity (CHS) Total Sectors* Maximum Capacity (LBA)* Multi-Sector Transfer

1 to 65,536 1 to 256 1 to 63 N/A N/A N/A Disabled Standard 2 sectors 4 sectors 8 sectors 16 sectors Disabled Enabled Disabled Enabled Standard Fast PIO 1 Fast PIO 2 Fast PIO 3 Fast PIO 4 Disabled Enabled

LBA Mode Control 32-Bit I/O Transfer Mode

Ultra DMA Mode

SMART Device Monitoring

Disabled Enabled

Enables UDMA Mode if your drive support this. Please be shure to use a short cable in very good quality; non additional connectors or adapters from the board connector to the hardisk allowed. Enables SMART warnings of imminent failure of drive.

Memory Shadow sub menu: Feature C800 - CBFF Option Disabled Enabled Description Accesses to this upper memory region go to the ISA bus if Disabled or to local memory if Enabled. NOTE: This option is not displayed if VGA BIOS exceeds 32kB! In that case this region is shadowed automatically. Accesses to this upper memory region go to the ISA bus if Disabled or to local memory if Enabled. see above. see above. see above.

CC00 - CFFF D000 D3FF D400 D7FF D800 - DBFF

Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled

p588m140.doc

Kontron Embedded Modules GmbH

Page: 13 of 44

MOPSlcd6 DC00 - DFFF Disabled Enabled

BIOS-Description see above.

Memory Cache sub menu: Feature System BIOS Video BIOS C800 - CBFF Option Disabled Enabled Disabled Enabled Disabled Enabled Description Caches the system BIOS to improve performance. Caches the video BIOS to improve performance. Controls caching of accesses to this upper memory region. NOTE: this option is not displayed if VGA BIOS exceeds 32k! In that case this region is handled by the option video BIOS. Controls caching of accesses to this upper memory region. see above. see above. see above. see above.

CC00 - CFFF D000 D3FF D400 D7FF D800 - DBFF DC00 - DFFF

Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled

The Advanced Menu

Selecting Advanced from the menu bar displays this menu: Feature Option 8Advanced Chipset Control sub menu Plug & Play OS Yes No No Yes Yes No sub menu sub menu sub menu DOS Other Description Opens Advanced Chipset Control sub menu. If your system has a PNP OS (e.g. Win95) select Yes to let the OS configure PNP devices not required for boot. No makes the BIOS configure them. Yes erases all configuration data in ESCD, which stores the configuration settings for plug-in devices. Select Yes when required to restore the manufacturers defaults. Yes prevents a Plug and Play OS from changing system settings. Opens PCI Advanced sub menu. Opens Keyboard Features sub menu. Opens I/O Device Configuration sub menu. Select DOS if you have DOS. Select Other if you have another OS such as UNIX. A large disk is one that has more than 1024 cylinders, more than 16 heads or more than 63 sectors per track. Determines if post errors cause the system to halt.

Reset Configuration Data

Secured Setup Configuration** 8PCI Configuration 8Keyboard Features 8I/O Device Configuration Large Disk Access Mode

Halt On Errors*

Yes No

*) P588R113 upwards, **) P588R116 upwards

p588m140.doc

Kontron Embedded Modules GmbH

Page: 14 of 44

MOPSlcd6 Advanced Chipset Control sub menu: Feature AT bus clock frequency Option 7.16 MHZ PCICLK/4 PCICLK/3 Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled 0, 1, 2, 3

BIOS-Description

Passive Release Delayed Transaction ISA Master Line Buffer DMA Line Buffer PCI to ISA Posted Write Buffer 16-bit ISA Memory Waitstates* 16-bit ISA I/O Waitstates* Enable Memory Gap ** CAS Latency SDRAM Timing

Description Allows to select ISA bus clock frequency. NOTE: Some ISA devices might not work at PCICLK/3 (11 MHz)! The max. ISA Clock in Spec IEEE P996 is 8.33 MHz Enables more efficient ISA Bus master cycles to PCI. Latches PCI-to-ISA cycles into buffer to free the PCI bus. Enables ISA master line buffer to enhance performance. Enables DMA line buffer to enhance performance. Enables PCI to ISA posted write buffer. Inserts wait state for 16-bit memory command Inserts wait state for 16-bit i/o command Turns system RAM of and frees address space (512kB-640kB or 15MB-16MB) for use with an option card. Select CAS Latency time. Controls RAS pre-charge timing in HCLKINs. tRP tRAS tRC Enables the asserting of NA (Next Address) when the cycle is a L2 or DRAM access cycle. Select the size of the primary frame buffer and enables Host to PCI write buffer Enables burst PCI cycles for VGA fixed frame buffer at A0000h BFFFFh. If enabled, only the words which address are consecutive linear can be merged into one line. Enables the byte-merge feature for frame buffer cycles Enables PCI fast back to back capability. Enables PCI write burst capability. If enabled, south bridge issues NMI to CPU when it detects the SERR assertion, IOCHK assertion and PCI bus parity error.

Pipe Function Primary Frame Buffer VGA Frame Buffer Data Merge Byte Merge Fast Back to Back PCI Write Burst Parity Check

0, 1, 2, 3 Disabled Conventional Extended 2 3 3-6-9 3-5-8 3-4-7 2-5-7 Disabled Enabled Disable, 1 MB, 2 MB, 4 MB, 8 MB, 16 MB Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled

p588m140.doc

Kontron Embedded Modules GmbH

Page: 15 of 44

MOPSlcd6 PCI Configuration sub menu: Feature PCI IRQ line 1

BIOS-Description

PCI IRQ line 2 PCI IRQ line 3 PCI IRQ line 4 USB IRQ line 8PCI/PNP ISA UMB Region Exclusion 8PCI/PNP ISA IRQ Resource Exclusion ISA graphics device installed

Option Disabled Auto IRQ3, 4, 5, 7, 9, 10, 11, 12, 14,15 see above see above see above see above sub menu sub menu No Yes

Description Select IRQ for PIC interrupt INTA. Select Auto to let the BIOS assign the IRQ. Select IRQ for PIC interrupt INTB. Select Auto to let the BIOS assign the IRQ. Select IRQ for PIC interrupt INTC. Select Auto to let the BIOS assign the IRQ. Select IRQ for PIC interrupt INTD. Select Auto to let the BIOS assign the IRQ. Select IRQ for embedded USB device. Select Auto to let the BIOS assign the IRQ. Opens UMB Region Exclusion sub menu. Opens IRQ Exclusion sub menu.

PCI devices may need to know if an ISA graphics device is installed in the system in order to enable that card to function correctly Yes Assign IRQ to PCI VGA Actually the onboard vga does not need an IRQ assigned, but Win98 2nd Edition doesnt No work correctly if no IRQ is assigned NOTE: Use IRQ Miniport driver for ALI M1543C south bridge (download from www.ali.com.tw) on Sytems running Win95!

p588m140.doc

Kontron Embedded Modules GmbH

Page: 16 of 44

MOPSlcd6

BIOS-Description

PCI/PNP ISA UMB Region Exclusion sub menu: Feature C800 - CBFF CC00 - CFFF D000 D3FF D400 D7FF D800 - DBFF DC00 - DFFF Option Available Reserved see above see above see above see above see above Description Reserves the specified block of upper memory for use by legacy ISA devices. see above see above see above see above see above

PCI/PNP ISA IRQ Exclusion sub menu: Feature IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 Keyboard Features sub menu: Feature Numlock Key Click Keyboard auto-repeat rate Keyboard auto-repeat delay Option Auto On Off Disabled Enabled 30/sec, 26.7/sec, 21.8/sec, 13.3/sec, 10/sec, 6/sec, 2/sec sec, sec, sec, 1 sec Description On or Off turns NumLock on or off at bootup. Auto turns NumLock on if it finds a numeric key pad. Turns audible key click on. Sets the number of times to repeat a keystroke per second if you hold the key down. Sets the delay time after the key is held down before it begins to repeat the keystroke. Option Available Reserved see above see above see above see above see above see above see above see above see above Description Reserves the specified IRQ for use by legacy ISA devices. see above see above see above see above see above see above see above see above see above

(only visible if IDE disabled)

p588m140.doc

Kontron Embedded Modules GmbH

Page: 17 of 44

MOPSlcd6 I/O Device Configuration sub menu: Feature Local Bus IDE adapter Floppy disk controller Base I/O address Floppy Drive Swap Serial port A Serial port B

BIOS-Description

Option Disabled Enabled Disabled Enabled Primary Secondary Disabled Enabled Disabled Enabled Auto OS Controlled Disabled Enabled Auto 3F8h, 2F8h, 3E8h, 2E8h IRQ 3, IRQ 4 IRQ 10, IRQ 11 Normal IrDA Ask-IR Standard Alternate Disabled Enabled Auto OS Controlled Output only Bi-directional ECP EPP 378h, 278h, 3BCh IRQ 5, IRQ 7 DMA0, 1, 2, 3 Disabled Enabled Disabled Enabled sub menu

Description Enables onboard PCI IDE device. Enables onboard FDC controller. Selects base address of onboard FDC conroller. (Primary = 3F0h, Secondary = 370) Swap drive A and B Disabled turns off the port. Enabled requires end user to enter the base I/O address and the IRQ. Auto makes the BIOS configure the port. OS Controlled lets the PNP OS configure the port after bootup. Disabled turns off the port. Enabled requires end user to enter the base I/O address and the IRQ. Auto makes the BIOS configure the port. Select I/O base of port. Select IRQ of port A and B Select IRQ of port C and D Selects mode of serial port D. Selects which pins of the SMC669 to use for the IrDA interface. Disabled turns off the port. Enabled requires end user to enter the base I/O address and the IRQ. Auto makes the BIOS configure the port. OS Controlled lets the PNP OS configure the port after bootup. Set the mode for the parallel port.

Serial port C Serial port D Base I/O address IRQ (port A and B) IRQ (port C and D) Mode ** Irda Pins ** Parallel Port

Mode

Base I/O address IRQ DMA USB Host Controller USB BIOS Legacy Support*

Select I/O base of port. Select IRQ of parallel port. Select DMA channel of port if in ECP mode. Enable or Disable onboard USB controller. Enable or Disable support for USB keyboard and mice. Please enable only for use with non-USB aware OSes such as UNIX and DOS. Opens Watchdog Settings sub menu

8Watchdog Settings

Notes: The italic printed options are only visible if an additional I/O controller (SMSC669) is on the OEM backplane! **) IrDA on ComD is supported. *) If USB legacy support is enabled, IRQ12 is used by the usb ohci controller. If you run a system with win9x and without a mouse attached, set irq12 to reserved in the PCI/PNP ISA IRQ Exclusion sub menu to prevent win9x from allocating irq12 for pci devices! Watchdog Settings sub menu: Feature Mode
p588m140.doc

Option Disabled

Description Select watchdog operation mode.

Page: 18 of 44

Kontron Embedded Modules GmbH

MOPSlcd6

BIOS-Description Reset NMI 1s, 5s, 10s, 30s, 1min, 5min, The time until the watchdog counter starts counting. Useful to handle longer boot 10min, 30min times. 0.4s, 1s, 5s, 10s, 30s, 1min, Max. trigger periode. 5min, 10min

Delay Timeout

The Security Menu

Selecting Security from the menu bar displays this menu: Feature Set Supervisor Passord Option Up to seven alphanumeric characters Up to seven alphanumeric characters Disabled Enabled Description Pressing <Enter> displays the dialog box for entering the user password. In related systems, this password gives full access to setup. Pressing <Enter> displays the dialog box for entering the user password. In related systems, this password gives restricted access to setup. Enabled requires a password on boot. Requires prior setting of the supervisor password. If supervisor password is set and this option is disabed, BIOS assumes user is booting. Write protect the boot sector on the hard disk for virus protection. Requires a password to format or Fdisk the hard disk. Enabled requires supervisor password to access floppy disk.

Set User Password

Password on boot

Fixed disk boot sector Diskette access

Normal Write protected User Supervisor

Enabling Supervisor Password requires a password for entering Setup. The passwords are not case sensitive! Note: User and Supervisor passwords are related! You cannot have a User password without first creating a Supervisor password.

The Power Menu

A power managment system reduces the amount of energy used after specified periods of inactivity. The setup menu supports a Full On state, a Standby state with partial power reduction, and a Suspend state with full power reduction. Use the Advanced Options sub menu to specify whether or not an activity can terminate a Standby or Suspend state and restore Full On. Selecting Power from the menu bar displays this menu: Feature Power Savings Option Disabled Customized Maximum Power Saving Maximum Performance Off, 1min, 2min, 4min, 6min, 8min, 12min, 16min Off, 5min, 10min, 15min, 20min, 30min, 40min, 60min Description Maximum options select predifined values. Select Customized to make your own selections from the following fields. Disabled turns off all power managment. Inactivity period required to put system in Standby mode (partial power shutdown). Inactivity period required after Standby to Suspend mode (maximum power shutdown).
Page: 19 of 44

Standby Timeout Auto Suspend Timeout

p588m140.doc

Kontron Embedded Modules GmbH

MOPSlcd6 Hard Disk Timeout 8Advanced Options LCD Backlight Off Timer

BIOS-Description Disabled, 10 sec 15 min sub menu Disabled, 28 sec 14 min Inactivity period of hard disk required before standby (motor off). Opens advanced options sub menu If enabled, backlight is switched off after the selected period of time without video activity

Advanced Options sub menu: Feature Video IO Primary HDD Floppy Disk Drive Serial I/O Parallel I/O Keyboard RTC monitored events: Video IO Primary HDD Secondary HDD FDD Serial I/O Parallel I/O Keyboard 3B0h 3DF I/O and A/B segment memory 1F0h 1F7h and 3F6h I/O access, primary IDE channel DMA request 170h 177h and 376h I/O access, secondary IDE channel DMA request 3F0h 3F7h I/O access 3F8h 3FFh, 2F8h 2FFh, 3E8h 3EFh, 2E8h 2EFh, 338h 33Fh, 238h 23Fh 378h 37Fh, 278h 27Fh, 3BCh 3BEh 60h and 64h I/O access Option Yes No Yes No Yes No Yes No Yes No Yes No Yes No Description Wakes up system on video event Wakes up system on primary HDD event. Wakes up system on FDD event. Wakes up system on serial I/O event. Wakes up system on parallel I/O event. Wakes up system on keyboard event. Wakes up system on RTC alarm.

Besides the events explained above the following events will wake the system from suspend state: IRQ[1-7], IRQ[9-15], NMI, SMI, INIT RTC IRQ 8

The Boot Menu

See chapter Boot Utilities below

The Exit Menu

The following sections describe the five possible options of the Exit Menu. Note that <Esc> does not exit this menu. You must select one of the items from the menu to exit.

Exit Saving Changes

Saves all the selections and exits setup. The next time you boots, the BIOS configures the system according to the Setup selection stored in CMOS.

Exit Discarding Changes

Use this option to exit Setup without storing in CMOS any new selections you may have made. The selections previously in effect remain in effect.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 20 of 44

MOPSlcd6

BIOS-Description

Load Setup Defaults

Select to display the default values for all the Setup menus.

Discard Changes
If, during a Setup session, you changeyour mind about changes you have made and have not yet saved the values to CMOS, you can restore the values you previously saved to CMOS.

Save Changes
Saves all the selection without exiting Setup. You can return to the other menus if you want to review and change your selection.

8.2

Boot Utilities

QuietBoot
Rigth after you turn on or reset the computer, Quietboot displays a graphical logo instead of the text based POST screen, which displays a number of PC diagnostic messages. The graphical logo stays up until just before the OS loads unless: You press <Esc> to display the POST screen You press <F2> to enter Setup POST issues an error message The BIOS or an option ROM requests keyboard input

MultiBoot
MultiBoot expands your boot options by letting you choose your boot device, which could be a hard disk, floppy disk, CD-ROM or network card. You can select your boot device in Setup, or you can choose a different device each time you boot by selecting your boot device in The Boot First Menu. MultiBoot consists of 4 menus:

The Setup Boot Menu

Feature Floppy Check Summary Screen QuickBoot Mode Dark Boot 8Boot Device Priority Onboard LAN RPL ROM * Option Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled sub menu Disabled Enabled Description Enabled verifies floppy type on boot; disabled speeds boot. If enabled, a summary screen is displayed just before booting the OS to let the end user see the system configuration. Allows the system to skip certain tests while booting. This will decrease the time needed to boot the system. If enabled, system comes up with a blank screen instead of the diagnostic screen during bootup. Opens boot device priority sub menu Enables Remote Program Load ROM of the onboard LAN controller. Supportes Intel PXE. Search for boot agent on intel website to find more informations.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 21 of 44

MOPSlcd6

BIOS-Description

The Boot Device Priority Menu

This menu allows to select the order of the devices from which the BIOS attempts to boot the OS. During POST, if BIOS is unsuccessful at booting from one device, it will try the next one on the list. The items on this menu each may represent the first of a class of items. For example, if you have more than one hard disk drive, Hard Drive represents the first of such drives as specified in the Hard Drive menu described below. To change the order select the device you want to change and press <-> to decrease or <+> to increase priority. Feature 8Removable Devices 8Hard Drives ATAPI CD-ROM Drive 8Network Boot Option boot priority & sub menu boot priority & sub menu boot priority boot priority & sub menu Description Sets boot priority of Removable Devices as described in the respective sub menu. Sets boot priority of Hard Disks as described in the respective sub menu. Sets boot priority of ATAPI CD:ROM Drives. Sets boot priority of Network Adapters as described in the respective sub menu.

The Removable Devices Menu

If you have more than one Removable Media drive, select Removable Devices and press <Enter> to display the Removable Media menu and choose which drive is represented in bootorder menu. Note: The standard 1.44MB floppy drive is referenced as Legacy Floppy Drives.

The Hard Drive Priority Menu

If you have more than one bootable hard drive, select Hard Drive and press <Enter> to display the Fixed Disk Menu and choose the boot priority.

The Network Boot Priority Menu

If you have more than one bootable network adapter in the system, select Network Boot and press <Enter> to display the available network adapters and choose the boot priority.

The Boot First Menu

Display the Boot First Menu by pressing <Esc> during POST. In response, the BIOS first displays the message Entering Boot Menu... and then displays the Boot Menu at the end of POST. Use the menu to select any of these options: Override the existing boot sequence (for this boot only) by selecting another boot device. If the specified device does not load the OS, the BIOS reverts to the previous boot sequence. Enter Setup Press <Esc> to continue with the existing boot sequence.

8.3

BIOS Update with Phoenix Phlash

Phoenix Phlash gives you the ability to update your BIOS from a floppy disk without having to install a new ROM chip. Phoenix Phlash is a utility for flashing a BIOS to the Flash ROM installed on the MOPS/lcd6. Use Phoenix Phlash for the following tasks only: Update the current BIOS with a newer version Restore a BIOS when it has become corrupted (see below) Phoenix Plash can be downloaded as a compressed file called CRISP588.ZIP from the Kontron wep page and contains the following files: MAKEBOOT.EXE CRISBOOT.BIN
p588m140.doc

Creates the custom boot sector on the Crisis Recovery Diskette The Crisis Recovery boot sector code
Kontron Embedded Modules GmbH Page: 22 of 44

MOPSlcd6 MINIDOS.SYS PHLASH.EXE WINCRISIS.EXE WINCRISIS.HLP PLATFORM.BIN BIOS.ROM

BIOS-Description Allows the system to boot in Crisis Recovery Mode Programs the flash ROM Executable file for creating the Crisis Recovery Diskette from Windows The help file of WINCRISES.EXE Performs platform-dependent functions Actual BIOS image to be programmed into flash ROM

To install Phoenix Phlash on your hard disk, unzip the content of CRISP588.ZIP into a local directory, presumable C:\PHLASH. To create the Crisis Recovery Diskette insert a clean diskette into drive A: or B: and execute WINCRISIS.EXE. This copies four files onto the Crisis Recovery Diskette: MINIDOS.SYS PHLASH.EXE PLATFORM.BIN BIOS.ROM Allows the system to boot in Crisis Recovery Mode Programs the flash ROM Performs platform-dependent functions Actual BIOS image to be programmed into flash ROM

If the BIOS image (BIOS.ROM) changes due to an update or bug fix, you can easily update the Crisis Recovery Disk. Simply copy the new BIOS.ROM image onto the diskette. You can run Phoenix Phlash in one of two modes: Command Line Mode Crisis Recovery Mode

Use the Command Line mode to update or replace your current BIOS. To execute Phlash in this mode, move to the Crisis Recovery Disk and type PHLASH. Phoenix Phlash will automatically update the BIOS. Phlash may fail if your system is using memory managers, in which case the utility will display the following message: Cannot flash when memory manager are present. If you see this message after you execute Phlash, you must disable the memory manager on your system!

8.4

Boot Block Support

Updating the BIOS may create a possible hazard: power failures or fluctuations that occur during updating the Flash ROM can damage the BIOS code, making the system unbootable. To prevent this possible hazzard the MOPS/lcd6 is equiped with a boot block Flash ROM. The boot block region contains a fail-safe recovery routine. If the boot block code finds a corrupted BIOS (checksum fails), it boots into the crisis recovery mode and loads a BIOS image from a special crisis diskette (see above). Additionally the end user can insert an update key into the parallel port to force initiating the boot block recovery routine. For further information on the update key and the crisis diskette check the Kontron web page.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 23 of 44

MOPSlcd6

Hardware Description

9. HARDWARE DESCRIPTION
9.1 ALI-Chipset Features

The MOPSlcd6 Board operates with the chipset ALI Aladdin IVPlus, which provides following features: North bridge M1531: Supports SDRAM DRAMs Fully synchronous 33Mhz 3.3V/5V tolerance PCI interface Enhanced power management South bridge M1543C B1: PCI 3.3V/5V tolerance interface Buffers control Provides steerable PCI interrupts for PCI device Plug-and-Play Enhanced UDMA controller Interrupt controller Counters/timers Distributed DMA supported Serialized IRQ supported Plug-and-Play supported Built-in keyboard controller Supports positive/subtractive decode for ISA device PMU features Built-in PCI IDE controller USB interface Super I/O interface

9.2

Memory configuration

The MOPSlcd6 uses only small outline Dual Inline Memory Modules (SO-DIMMs). One socket is available for 3.3 Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of either 32 or 64MB.

9.3
IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 Notes:

Interrupts
System Timer Keyboard Cascade COM 2 note (1) COM 1 note (1) Available Floppy LPT 1 Clock/Calendar Available Available Available Available Numeric-processor EIDE Channel 1 Available

p588m140.doc

Kontron Embedded Modules GmbH

Page: 24 of 44

MOPSlcd6 (1)

Hardware Description

if serial ports are disabled via system bios, these interrupts are available for other devices.

9.4
DMA 0 DMA 1 DMA 2 DMA 3 DMA 4 DMA 5 DMA 6 DMA 7

ISA DMA
Available Available Floppy Available Cascade Available Available Available

p588m140.doc

Kontron Embedded Modules GmbH

Page: 25 of 44

MOPSlcd6

Hardware Description

9.5

Onboard VGA 69000

Block Diagram

Intern PCIBUS

CRT

HiQV64
with 2 MB RAM

internal panel connector plug-and-play

Driver
The latest drivers for the 69000 are available on http://www.asiliant.com/driver.htm

Supported Display Types

The MOPSlcd6 supports a vast variety of panels all configured by a dedicated cable for each panel. There is no jumper setting or software setup required. Since practically all LCDs have different connectors, pinout or LCD voltages, this is the easiest and safest way to configure different panels. The MOPSlcd6 BIOS supports different panel types, which are identified via the video BIOS by reading the configuration on internal panel connector.

Power Supply
The on board 3.3V-circuitry and low-voltage panels are powered by their own separated voltage regulators, the one for the LCD is mounted on the adapter cable. If the used backlight converter needs +12V, supply system also with +12V.

The LC-Display Interface Connecting a Display

Many different panel adapters for a wide spread variety of displays are available through Kontron. If you use one of those adapters supplied by Kontron, configuration is very easy: 1. Check, whether you have the correct adapter and cable for the panel you plan to use. Inspect the cable for damages. 2. Disconnect power from your System. 3. Connect the panel adapter to the internal LCD connector on MOPSlcd6. 4. Connect the other end of the cable to your display. 5. Connect the backlight converter. 6. Supply power to your system

p588m140.doc

Kontron Embedded Modules GmbH

Page: 26 of 44

MOPSlcd6

Hardware Description

7. If no picture appears on your display, you should connect a CRT monitor to the CRTconnector. If you still dont see any improvement, you may consider contacting the dealer for technical support.

Current panel information from the Kontron-Website

To find out whether your panel is supported, you should check the Kontron support pages on the Internet for actual panel lists. We regularly update the list of panels that have been tested with the MOPSlcd6.

Available Video Modes

Video Mode 00h/01h 02h/03h 04h/05h 06h 07h 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h 22h 24h 28h 30h 31h 32h 34h 38h 40h 41h 42h 43h 44h 45h 50h 52h 62h 63h 64h 68h 6Ah 70h 71 72
p588m140.doc

Display Mode Text Text Graphics Graphics Text Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics Graphics

Characters/Pixels 40x25 80x25 320x200 640x200 80x25 320x200 640x200 640x350 640x350 640x480 640x480 320x200 320x200 320x200 320x200 320x240 320x240 320x240 400x300 400x300 400x300 512x384 512x384 512x384 640x480 800x600 1024x768 1280x1024 640x480 640x400 800x600 1024x768 1280x1024 640x480 640x480 800x600 800x600 1024x768 1024x768 640x480 800x600 640x400 640x400 1024x768 1280x1024 800x600 640x480 640x400 800x600

Colors/Gray val. 16 16 4 2 Mono 16 16 Mono 16 2 16 256 256 64k 16M 256 64k 16M 256 64k 16M 256 64k 16M 16 16 16 16 256 256 256 256 256 32k 64k 32k 64k 32k 64k 16M 16M 64k 16M 16 16 16 256 256 256

Refresh Rate 70 70 70 70 70 70 70 70 70 60 60 70 70 70 70 60 60 60 60 60 60 60 60 60 85 85 85 60 85 70 85 85 60 85 85 85 85 85 85 85 85 70 70 85 60 85 85 70 85
Page: 27 of 44

Kontron Embedded Modules GmbH

MOPSlcd6
74 78 Graphics Graphics

Hardware Description
1024x768 1280x1024 256 256 85 60

9.6

Watchdog Extension

With the aid of a special Interrupt 15h function, the watchdog on a Kontron board can be controlled very easily. The respective functions have the following calling conventions: Watchdog init Input: Int 15h 00h AH = E0h AL = 00h BX = timeout in 0.2sec increments CX = delay in 0.2sec increments DX = watchdog action (0 = reset, 1 = NMI) None This funcion is a public Kontron INT15h extension used to init the watchdog on Kontron boards.

Output: Description:

Watchdog trigger Input: Output: Description:

Int 15h 01h AH = E0h AL = 01h None This funcion is a public Kontron INT15h extension used to trigger the watchdog on Kontron boards.

Detailed description of the watchdog function:

Programming: The function Init watchdog must be called only once. The three parameters delay time, timeout time an trigger event must be set. After initialisation the watchdog will be active only after the delay time has expired. The watchdog must be reset during the timeout time with the trigger watchdog function. Otherwise a RESET or NMI will occur depending on trigger event. The trigger- and the delay time can be set in steps of 0.2 sec. The maximum values are: timeout time 65535*0.2sec. = 13107s 3h 38min delay time 32767*0.2sec. = 6553s 1h 49min The system BIOS makes it very easy to use the watchdog via software interrupt 15h. Two ways are possible to access the watchdog: The simplest way is to use AH=0E0h to init or trigger the watchdog. The second way is to use the functions Write I2C and Read I2C with AH=0E1h and handling the I2C bus protocol. A) Simple with AH = E0h Init Watchdog (Int 15h, AH=E0h) Called with AX BX CX DX Returns Example mov mov mov
p588m140.doc

E000h timeout time BX = 0 watchdog off. BXmax = 0FFFFh delay time CX = 0 no delay. CXmax = 07FFFh trigger event DX = 0 RESET, DX = 1 IOCHCHK

no ax,0E000h bx,5 cx,5 ; Watchdog set ; 5*0,2s = 1s Timeout ; 5*0,2s = 1s Delay

Page: 28 of 44

Kontron Embedded Modules GmbH

MOPSlcd6 mov int dx,0 15h

Hardware Description ; after Timeout and Delay generate RESET

p588m140.doc

Kontron Embedded Modules GmbH

Page: 29 of 44

MOPSlcd6

The JIDA Standard

10. THE JIDA STANDARD

JIDA is the abbreviation for JUMPtec Intelligent Device Architecture. Every board with onboard BIOS extension shall support the following function calls, which supply information about the board. JIDA functions are called via Interrupt 15h with AH=EAh, AL=function number, DX=4648h (security word), CL=board number (starting with 1). The interrupt will return with CL#0, if a board with the number specified in CL does not exist. CL will be equal to 0 if the board number exists. In this case, the content of DX is used to determine, if operation was successful. DX=6B6Fh indicates successful operation, any other value indicates an error. To get information about the installed boards following the JIDA standard, the following procedure is recommended: Call Get Device ID with CL=1. The name of the first device installed will be returned. If result was Board exists (CL=0), increment CL and call Get Device ID again. Repeat until result is Board not present (CL#0). You now know the names of all boards within your systen that follow the JIDA standard. More information about a specific board may then be obtained by calling the appropriate inquiry function with the boards number in CL. WARNING: Association between board and board number may change due to configuration changes. Do not rely on any association between board and board number. Instead, always use the procedure described in the preceding paragraph first, to determine the association between board and board number. The source of a Turbo-Pascal unit called JIDA_ACC.PAS showing JIDA access is available from our webpage at www.pc104-mops.com. Get Manufacturer ID Input: Int 15h AX = EA00h DX = 4648h CL = Board number (1=first board a.s.o.) ES:BX = Pointer to destination data area CL=0: Board present CL0: Board not present DX=6B6Fh: Function successful DX6B6Fh: Error

Output: Description:

If CL=0 and DX=6B6Fh, then 4 Byte manufacturer ID were copied to the area pointed to by ES:BX By default, the result will be JUMP. Note: There is no ending zero byte. Function must be implemented on every device supporting the JIDA. Int 15h AX = EA01h DX = 4648h CL = Board number ES:BX = Pointer to destination data area CL=0: Board present CL0: Board not present DX=6B6Fh: Function successful DX6B6Fh: Error

Get Device ID Input:

Output: Description:

If CL=0 and DX=6B6Fh, then 7 Byte device ID were copied to area pointed to by ES:BX By default, the result will be Note: There is no ending zero byte. Function must be implemented on every device supporting the JIDA.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 30 of 44

MOPSlcd6 Get Manufacturing Date Input: Output:

The JIDA Standard Int 15h AX = EA02h CL = Board number CL=0: Board present CL0: Board not present BX = Manufacturing date DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Description

If CL=0 and DX=6B6Fh, then BX=Manufacturing date. Date format is the same as used for DOS files: Bit0..4: Day Bit5..8: Month Bit9..15: Years since 1980 Int 15h AX = EA03h DX = 4648h CL = Board number ES:BX = Pointer to destination data area CL=0: Board present CL0: Board not present DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Get Serial Number Input:

Output: Description:

If CL=0 and DX=6B6Fh, then 10 Byte serial number were copied to area pointed to by ES:BX The result is different for each single P588. Note: There is no ending zero byte. Int 15h AX = EA04h CL = Board number CL=0: Board present CL0: Board not present BH=Major revision number BL=Minor revision number Int 15h AX = EA05h CL = Board number CL=0: Board present CL0: Board not present BH=Major revision number BL=Minor revision number Int 15h AX = EA06h CL = Board number CL=0: Board present CL0: Board not present BX = Last repair date.

Get Hardware Revision Input: Output:

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Get Firmware Revision Input: Output:

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Get Last Repair Date Input: Output:

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Description:

If CL=0 and DX=6B6Fh, then BX=Last repair date. For date format see function Get Manufacturing Date. If board was never repaired, result will be equal to manufacturing date.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 31 of 44

MOPSlcd6 Read Running Time Meter Input: Output:

The JIDA Standard Int 15h AX = EA07h CL = Board number CL=0: Board present CL0: Board not present BX=Running time (hours) CH=Overflow counter Int 15h AX = EA08h CL = Board number CL=0: Board present CL0: Board not present BX = Boot counter Int 15h = EA09h = Board number DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

ReadBoot Counter Input: Output:

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Get JIDA Revision Level Input: Output:

AX CL

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn. not implemented

CL=0: Board present CL0: Board not present BH = Major revision number BL = Minor revision number Int 15h AX CL BH

Read User Byte from EEPROM Input:

= EA40h DX = 4648h = Board number = Number of byte to read (0..15 allowed) DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Output:

CL=0: Board present CL0: Board not present BL = Value read Int 15h AX CL BH BL

Write User Byte to EEPROM Input:

= EA41h DX = 4648h = Board number = Number of byte to write (0..15 allowed) = Value to write DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

Output:

CL=0: Board present CL0: Board not present Int 15h AX CL = EA42h = Board number

Get Number of User Bytes available in EEPROM Input: Output:

DX = 4648h DX=6B6Fh: Function successful DX6B6Fh: Fn.not implemented

CL=0: Board present CL0: Board not present BL=Number of Bytes available Note: BL=0 means 256 Bytes

p588m140.doc

Kontron Embedded Modules GmbH

Page: 32 of 44

MOPSlcd6

Network Operation

11. NETWORK OPERATION

11.1 Overview
The Ethernet interface on MOPSlcd6 is realized with the 82551ER from Intel, a fully integrated 10BASE-T/100BASE-TX LAN solution. The 82551ER consists of both the Media Access Controller (MAC) and the physical layer (PHY) interface combined into a single component solution. The 32-bit PCI controller provides enhanced scatter-gather bus mastering capabilities and enables the 82551ER to perform high speed data transfers over the PCI bus. Two large transmit and receive FIFOs of 3 Kbyte each help prevent data underruns and overruns while waiting for bus accesses. The 82551ER can operate in either full duplex or half duplex mode. In full duplex mode the 82551ER adheres with the IEEE 802.3x Flow Control specification. Half duplex performance is enhanced by a proprietary collision reduction mechanism. The 82551ER also includes an interface to a serial (4-pin) EEPROM. The EEPROM provides power-on initialization for hardware and software configuration parameters. The 82551ER provides following features: Integrated IEEE 802.3 10BASE-T and 100BASE-TX compatible PHY Glueless 32-bit PCI master interface Improved dynamic transmit chaining with multiple priorities transmit queues Backward compatible software to the 82558 and 82557 Full Duplex support at both 10 and 100Mbps IEEE 802.3u Auto-Negotiation support 3 Kbyte transmit and 3 Kbyte receive FIFOs Fast back-to-back transmission support with minimum interframe spacing IEEE 802.3x 100BASE-TX Flow Control support Adaptive Technology TCP/UDP checksum offload capabilities Low power 3.3 V device Clockrun protocol support

11.2 Configuration 82551ER

Perform the following steps to configure your 82551ER PCI Ethernet Adapter: 1. Connect your network cable The cable must be connected before loading the setup tool. To check the adapter's configuration run the 82551ER DOS setup utility, named setup.exe, included in the driver archive. The setup utility shows the adapters configuration: Adaper type: Adapter part number: Network address: Interrupt: Bus: Slot: Device: Network speed: Physical layer device: Duplex: Adapter capabilities: Currently selected adapter. Part number of the adapter. Node (MAC) address of adapter in hexadecimal. The interrupt the PCI BIOS assigned to the adapter. PCI bus number slot ID of the adapter. Slot number used for the adapter drivers. Device number assigned by the PCI BIOS. Speed of the current network link. Actice physical layer device. Current duplex setting. Link type supported by this adapter.

2. Perform diagnostic tests Test adapter in main menu if needed.

p588m140.doc Kontron Embedded Modules GmbH Page: 33 of 44

MOPSlcd6

Network Operation

11.3 Software and driver setup

Please refer to the corresponding readme and setup/install files.

11.4 Ethernet Technical Support

Many problems can be solved with the latest drivers for the 82551ER controller. In our system the 82551ER is working in 82559ER compatibility mode; so no additional changes on the drivers in your system are necessary ! Please use the 82559ER drivers. Kontron provides you with the latest tested drivers, which might be quite different from the newest ones. Therefore feel free to contact the Intel web page for driver updates. For further technical support, contact either Kontron or get support information and download software updates from Intel's World Wide Web server. Intel World Wide Web server Support: Corporate: http://support.intel.com http://www.intel.com

Before contacting Kontron for technical support, be prepared to provide as much of the following information as possible. 1) Adapter type 2) Adapter configuration 3) - I/O Base, Memory Base, I/O or memory mode enabled, IRQ, and DMA channel - Configured for media auto-detect or specific media type (which type). (Record this information from the driver's sign-on message if possible.) 4) Computer System's Configuration - BIOS (make and version) - System make and model - CPU (type and speed) - System RAM 5) Software - 82551ER or 82559ER driver and version - Your network operating system and version - Your system's OS make/version (MS-DOS, Novell's DOS, Win95, WFWG, etc.) - Version of all protocol support files - Frame types supported by you server 6) Contents of your configuration files - CONFIG.SYS - AUTOEXEC.BAT - PROTOCOL.INI - NET.CFG FILE - WINDOW'S SYSTEM.INI (if using Windows client) - AUTOEXEC.NCF file - or similar 7) Any Error Message displayed.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 34 of 44

MOPSlcd6

Specifications

12. SPECIFICATIONS
12.1 Mechanical Specifications
PC/104 Bus connector: connector PC/104plus connector 2 pieces of 2*32 pin male and 2*20 pin male 4*30 pin 2mm connector

REMEMBER: The PC/104plus connector is without connector shroud. Its not possible to use a PC/104plus board with connector shroud at top at MOPSlcd6 and MOPS/686+. This is only a mechanical limitation and does not reduce the functionality of MOPSlcd6 and MOPS/686+. Please order a module without connector shroud or place MOPSlcd6/ MOPS/686+ at top at the stack. Module-dimensions: length * width 95 mm * 90 mm (3,7" * 3,5 ")

12.2 Electrical Specifications

Supply voltage: Supply voltage ripple: Supply current (maximal): ( max. current all Parts) 5V DC +/- 5% 100 mV peak to peak 0 - 20 MHz 1,8 A + current DRAM + current Prozessor

Supply current (typical, DOS-Prompt): with 166 MHz CPU and 64 MB SDRAM with 266 MHz CPU, Fan and 64 MB SDRAM external RTC battery voltage external RTC battery quiescent current

1,60 A 1,85 A 2,4 4,0 V max. 2 uA

The MOPSlcd6 is not a replacement for a backplane! Its strictly recommended to use all Power Pins on the PC/104 connector for power supply of the MOPSlcd6 and additional I/O cards. The MOPSlcd6 is not a replacement for a backplane! Its not acceptabel to use only the power pins of the PC/104plus PCI connector for power supply of the full PC/104 stack. The MOPSlcd6 is not a replacement for a backplane! Please refer the PC/104plus specification for the power supply of the MOPSlcd6 and all additional PC/104 I/O-cards.

12.3 Environmental Specifications

Temperature: operating 0 to +60 C ((*)with appropriate airflow)) except CPU and chipset (see below) non operating: -10 to +85 C

The Intel Pentium Processor with MMX Technology on 0.25 Micron is specified for proper operation when case temperature is within the specified range of 0C to 95C. The chipset M1531 and M1543C on the back side are specified for extended temperature range of 0C to 85C. Humidity: operating: 10% to 90% (non-condensing) non operating: 5% to 95% (non-condensing)

(*) The maximum operating temperature is the maximum measurable temperature on any spot on the moduless surface. It is the users responsibility to maintain this temperature within the specification, which is set by the IC manufacturer.
p588m140.doc Kontron Embedded Modules GmbH Page: 35 of 44

MOPSlcd6

Peripheral Interface

13. PERIPHERAL INTERFACE

13.1 Keyboard, Reset, Battery, Speaker
Signal name SPKR GND POWERGOOD /KLOCK KDATA KCLK GND +5V )*1 VBAT POWERGOOD Function speaker output Ground reset input keyboard lock keyboard data keyboard clock Ground +5V VBAT input (3,6V) reset input 5-pin diode keyboard adapter 6-pin minidin keyboard adapter (PS2)

2 1 4 5

1 5 3 4

/KLOCK (keyboard lock)

input on CPU modules output on any other module input to the keyboard controller input port 1 bit 7 .

POWERGOOD (reset input)

input on CPU modules open collector output on all other module When power good goes high, it starts the reset generator on the CPU module to pull the onboard reset line high after a valid reset period. This pin can also be used as a low active hardware reset for modules.

SPKR (speaker output)

open collector output on modules which can drive a loudspeaker. input on modules which connect a 8 Ohm loudspeaker to this pin An 8 Ohm loudspeaker is connected between SPEAKER and GND. Only one loudspeaker should be connected to this pin. Usually only the CPU drives this pin, however other modules can also use this signal to drive the system loudspeaker.

KDATA (keyboard data)

bi-directional I/O pin on CPU modules Keyboard data signal.

KCLK (keyboard clock)

bi-directional I/O pin on CPU modules Keyboard clock signal.

VBAT (system battery connection)

This pin connects a system battery to all modules. The battery voltage has to be higher than 3.0V and lower than 4.0V. Either a 3V or 3.6V battery is recommended. Note, that there is no battery needed to hold the CMOS-setup data. Your configuration concerning hard disks, floppy drives etc. is automatically saved in an onboard FRAM. Nevertheless the battery is necessary to serve the CMOS date and time while power consumption is turned off.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 36 of 44

MOPSlcd6

Peripheral Interface

1 (Speaker)

2 (GND)

3,10 (PowerGood)

4 (/KLOCK)

5 (KDATA)

6 (KCLK) 5 7 (GND) 2 4 8 (+ 5V) 1 3

9 (VBAT)

13.2 Serial Port COM A, B RS232C

Pin 1 2 3 4 5 6 7 8 9 10 Signalname In / Out DCD DSR RxD RTS TxD CTS DTR RI GND +5V )*1 In In In Out Out In Out In --DSUB-25 (need Adapter) 8 6 3 4 2 5 20 22 7 -DSUB-9 (need Adapter) 1 6 2 7 3 8 4 9 5 --

For signal description please refer to additional literature. The four serial input/output interfaces can be set to any I/O-address on the periphal setup. The serial ports are completely compatible with the serial port implementation used on the IBM Serial Adapter. Their default interrupts are mapped to IRQ4 and IRQ3.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 37 of 44

MOPSlcd6

Peripheral Interface

13.3 Parallel Port LPT 1

Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 2 4 6 8 26 10,12 14,16 18,20 22,24 Signalname /Strobe Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 /ACK BUSY PAPER out SEL out /AUTOFD /ERROR /INIT SEL in +5V )*1 GND GND GND GND Function In / Out Out I/O I/O I/O I/O I/O I/O I/O I/O in in in in out in out out -----DSUB-25 (need Adapter) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 NC 18 - 25 18 - 25 18 - 25 18 - 25

+5V Signal Ground Signal Ground Signal Ground Signal Ground

For signal description please refer to additional literature. The Centronics printer interface can be programmed via the system setup menu.Refer to the periphal setup for more informations. The parallel port is completely compatible with the parallel port implementation used in the IBM PS-II-Parallel Adapter.

13.4 Floppy Connector

Signal P i n 1 3 5 7 9 1 1 13 15 17 19 21 23 25 NC GND GND GND GND GND GND Ground Ground Ground Ground Ground Ground 14 16 18 20 22 24 26 STEP WD WG TR00 WP RD SIDE step write data write gate track 00 write protect read data side one select +5V )*1 +5V )*1 +5V )*1 NC NC NC + 5V + 5V + 5V 2 4 6 8 10 12 IDX DS0 /DCHNG NC Mo0 DIR index drive select 0 disk change motor on direction select Function Pin Signal Function

For signal description please refer to additional literature.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 38 of 44

13.5 IDE Connector for 2,5" Hard Disk

Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Signal /RESET D7 D6 D5 D4 D3 D2 D1 D0 GND NC /IOW /IOR NC NC IRQ14 SA1 SA 0 /CS0 /HDLED +5V )*1 GND Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 Signal GND D8 D9 D10 D11 D12 D13 D14 D15 NC GND GND GND BALE GND /IOCS16 NC SA2 /CS1 GND +5V )*1 NC

For signal description please refer additional literatur.

13.6 Ethernet Connector

Pin 1 2 3 4 5 6 7 8 Signalname TXD+ TXDRXD+ NC NC RXDNC NC Function 100/10BASE-T Transmit 100/10BASE-T Transmit 100/10BASE-T Receive Unused Pin Unused Pin 100/10BASE-T Receive Unused Pin Unused Pin In/Out differential Output differential Output differential Input

differential Input Output Output

TXD+, TXDDifferential output pair.

RXD+, RXDDifferential input pair.

13.7 CRT Connector

Pin 1 2 3 4 5 6
p588m140.doc

Signal name Function RED GREEN BLUE GND VSYNC HSYNC analog video red analog video green analog video blue signal ground vertical sync horizontal sync

DSUB15 (need adapter) 1 2 3 7 14 13

Page: 39 of 44

Kontron Embedded Modules GmbH

MOPSlcd6

Peripheral Interface

13.8 USB Connector

Pin 1 2 3 4 Pin function +5V )*1 USBUSB+ GND

The power contacts on PIN 1 and 4 are are only usable for internal USB devices. Its strictly recommended to use a resetable fuse for power on external USB connectors to follow the USB specification.

13.9

Power Connector
Pin 1 2 3 4 5 6 7 8 Pin function GND +5V VBAT +12V -5V -12V GND +5V

Power Pins
The MOPSlcd6 is a +5 V only module. The power consumption of all available power pins on the MOPSlcd6 is limited to 5A in total (1A per pin, with 2 pins on the power connector, 2 pins on the XT-bus and 1 pin on the AT-bus) and at GND up to 8A. The MOPSlcd6 is not a replacement for a backplane! Its strictly recommended to use all Power Pins on the PC/104 connector for power supply of the MOPSlcd6 and additional I/O cards. The MOPSlcd6 is not a replacement for a backplane! Its not supported to use only the power pins of the Power connector or/and PC/104plus PCI connector to supply the power of other devices on the PC/104 stack through the MOPSlcd6. The MOPSlcd6 is not a power supply !. If your additional PC/104plus PCI card needs other voltages on the PC/104 and the PC/104plus connector please add a power supply on your backplane.

VBAT (system battery connection)

This pin connects a system battery to all modules. The battery voltage has to be higher than 3.0V and lower than 4.0V. Either a 3V or 3.6V battery is recommended. Note, that there is no battery needed to hold the CMOS-setup data. Your configuration concerning hard disks, floppy drives etc. is automatically saved in an onboard FRAM. Nevertheless the battery is necessary to serve the CMOS date and time while power consumption is turned off. )*1 Note: (*) To protect external power lines of peripheral devices, make sure that -- the wires have the right diameter to withstand maximum available current -- the enclosure of the peripheral device fulfils fire-protecting requirements of IEC/EN 60950.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 40 of 44

MOPSlcd6

LiteraturE, Standards, Links

14. LITERATURE, STANDARDS, LINKS

Below is a list of information sources to help you to further understand PC architecture.

14.1 Buses
PC/104-Bus
PC/104 Specification Version 2.3 June 1996 PC/104-Plus Specification Version 1.1 June 1997 PC/104 Consortium; www.pc104.org

ISA, Standard PS/2 - Connectors AT Bus Design: Eight and Sixteen-Bit ISA, E-ISA and EISA Design, Edward Solari, Annabooks, 1990, ISBN 0-929392-08-6 AT IBM Technical Reference Vol 1&2, 1985 ISA & EISA Theory and Operation, Edward Solari, Annabooks, 1992, ISBN 0929392159 ISA Bus Specifications and Application Notes, Jan. 30, 1990, Intel ISA System Architecture, Third Edition, Tom Shanley and Don Anderson, Addison-Wesley Publishing Company, 1995, ISBN 0-201-40996-8 Personal Computer Bus Standard P996, Draft D2.00, Jan. 18, 1990, IEEE Inc Technical Reference Guide, Extended Industry Standard Architecture Expansion Bus, Compaq 1989

PCI PCI SIG The PCI-SIG provides a forum for its ~900 member companies, who develop PCI products based on the specifications that are created by the PCI-SIG. PCI & PCI-X Hardware and Software Architecture & Design, Fifth Edition, Edward Solari and George Willse, Annabooks, 2001, ISBN 0-929392-63-9. PCI System Architecture, Tom Shanley and Don Anderson, Addison-Wesley, 2000, ISBN 0-201-30974-2.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 41 of 44

MOPSlcd6

LiteraturE, Standards, Links

14.2 General PC Architecture

Embedded PCs, Markt&Technik GmbH, ISBN 3-8272-5314-4 (German) ePanorama PC Hardware ePanorama.net is dedicated to offer information on electronics found on the Web. Hardware Bible, Winn L. Rosch, SAMS, 1997, 0-672-30954-8 Interfacing to the IBM Personal Computer, Second Edition, Lewis C. Eggebrecht, SAMS, 1990, ISBN 0-672-22722-3 The Indispensable PC Hardware Book, Hans-Peter Messmer, AddisonWesley, 1994, ISBN 0-201-62424-9 The PC Handbook: For Engineers, Programmers, and Other Serious PC Users, Sixth Edition, John P. Choisser and John O. Foster, Annabooks, 1997, ISBN 0-929392-36-1

14.3 Ports
RS-232 Serial EIA-232-E Interface The EIA-232-E standard specifies the interface between (for example) a modem and a computer so that they can exchange data. The computer can then send data to the modem, which then sends the data over a telephone line. The data that the modem receives from the telephone line can then be sent to the computer. RS-232 Made Easy: Connecting Computers, Printers, Terminals, and Modems, Martin D. Seyer, Prentice Hall, 1991, ISBN 0-13-749854-3 National Semiconductor Interface Data Book includes application notes. Type 232 as a search criteria to obtain a list of application notes.

p588m140.doc

Kontron Embedded Modules GmbH

Page: 42 of 44

MOPSlcd6

LiteraturE, Standards, Links

IDE Technical Committee T13 is responsible for all interface standards relating to the popular AT Attachment (ATA) storage interface utilized as the disk drive interface on most personal and mobile computers today. The X3T10 standard defines an integrated bus interface between disk drives and host processors. It provides a common point of attachment for systems manufacturers and the system. We recommend you also search for information on 4.2 I/O cable if you use hard disks in a DMA3, DMA4 , DMA5 or PIO4 mode. USB USB specification USB Implementers Forum, Inc. is a non-profit corporation founded by the group of companies that developed the Universal Serial Bus specification. The USB-IF was formed to provide a support organization and forum for the advancement and adoption of Universal Serial Bus technology.

14.4 Programming
C Programmers Guide to Serial Communications, Second Edition, Joe Campbell, SAMS, 1987, ISBN 0-672-22584-0 Programmer's Guide to the EGA, VGA, and Super VGA Cards, Third Edition, Richard Ferraro, Addison-Wesley, 1990, ISBN 0-201-57025-4 The Programmers PC Sourcebook, Second Edition, Thom Hogan, Microsoft Press, 1991, ISBN 1-55615-321-X Undocumented PC, A Programmers Guide to I/O, CPUs, and Fixed Memory Areas, Frank van Gilluwe, Second Edition, Addison-Wesley, 1997, ISBN 0201-47950-8

p588m140.doc

Kontron Embedded Modules GmbH

Page: 43 of 44

MOPSlcd6

Document Revision History

15. DOCUMENT REVISION HISTORY

Filename P588M140 Date Edited by WKA Alteration to preceding revision Created preliminary for new HW Rev.; kill JUMPtec delete all power through MOPS as an backplane mistakes by CE and UL considerations ;

p588m140.doc

Kontron Embedded Modules GmbH

Page: 44 of 44