Cablofil, Inc.

8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
SECTION 260536 (16139) - CABLE TRAYS PART 1 - GENERAL

Specifier Note: Section numbers and titles are from MasterFormat 2004 Edition with numbers and titles from MasterFormat 1995 Edition as well. SCHEDULE 0 - SECTION INCLUDES: PRODUCT DATA SHEET 0 - Continuous, rigid, welded steel or stainless steel wire mesh cable management system. PRODUCT DATA SHEET 1 - Cable tray systems are defined to include, but are not limited to, straight sections, supports and accessories. SCHEDULE 1 - RELATED DOCUMENTS: PRODUCT DATA SHEET 0 - Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. SCHEDULE 2 - SUMMARY PRODUCT DATA SHEET 0 - Related Sections include the following: 2004 Edition 1. Section 26 05 13 - Medium-Voltage Cables. 2. Section 26 05 19 - Low-Voltage Electrical Power Conductors and Cables. 3. Section 26 05 23 - Control-Voltage Electrical Power Cables. 4. Section 26 05 33 - Raceway and Boxes for Electrical Systems. 5. Section 27 05 28.36 - Cable Trays for Communications Systems. 6. Section 27 10 00 - Structured Cabling. 7. Section 28 05 13 - Conductors and Cables for Electronic Safety and Security. 8. Section 28 05 28.36 - Cable Trays for Electronic Safety and Security. 1995 Edition 0.1 Section 16120 - Conductors and Cables. 0.2 Section 16130 - Raceway and Boxes. 0.3 Section 16140 - Wiring Devices. 0.4 Section 16150 - Wiring Connections. 0.5 Section 16200 - Electrical Power. 0.6 Section 16700 Communications.

CABLE TRAYS

16139 - 1

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com

PRODUCT DATA SHEET 1 - References:

1.1 1.2 IEC 61537 (2001) Cable Tray Systems and Cable Ladder Systems for Cable Management NEMA VE 1-2002/CSA C22.2 No. 126.1-02 Metal Cable Tray Systems ANSI/NFPA 70 (2005) National Electrical Code (NEC) TIA 569-A (1998) Commercial Building Standard for Telecommunications Pathways & Spaces ASTM A 510 - Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel ASTM A 380 Specification for Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems ASTM B 633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel ASTM A 123 Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products ASTM A 653 - Specification for Steel Sheet, Zinc-Coated (Galvanized) by the Hot-Dip Process, Structural (Physical) Quality Norm NF/A 91-131 for Galvanized Steel Norm NF/EN 12-329 for Electrozinc Coating Norm NF/EN/ISO 14-61 for Hot-Dipped Galvanized Steel Norm NF 10-088-2 for Stainless Steel

1.3
1.4 1.5 1.6

1.7 1.8
1.9

1.10
1.11 1.12 1.13

SCHEDULE 3 - SUBMITTALS PRODUCT DATA SHEET 0 - Comply with requirements of Section 01330 Submittal Procedures. PRODUCT DATA SHEET 1 - Product Data: Submit manufacturers product data sheets for cable tray indicating dimensions, materials, and finishes, including UL Classification and NEMA/CSA Certification. PRODUCT DATA SHEET 2 - Shop Drawings: Submit shop drawings indicating materials, finish, dimensions, accessories, layout, supports, splices, and installation details. PRODUCT DATA SHEET 3 - Design Calculations: Verify loading capacities for supports.

PRODUCT DATA SHEET 4 - Coordination Drawings: Include floor plans and sections drawn to scale.
Include scaled cable tray layout and relationships between components and adjacent structural and mechanical elements. Data presented on these drawings are as accurate as preliminary surveys and planning can determine. Field verification of all dimensions, routing, etc., is directed.

CABLE TRAYS

16139 - 2

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com PRODUCT DATA SHEET 5 - Factory-certified test reports of specified products, complying with IEC 61537,
NEC, and NEMA VE 1/CSA C22.2 No. 126.1.

PRODUCT DATA SHEET 6 - Submit manufacturers certification indicating ISO 9001 quality certified. PRODUCT DATA SHEET 7 - Submit training procedure for certifying cable tray installers.
SCHEDULE 4 - QUALITY ASSURANCE PRODUCT DATA SHEET 0 - Source Limitations: Obtain cable tray components through one source from a single manufacturer.

PRODUCT DATA SHEET 1 - Approval and Labeling: Provide cable trays and accessories specified in this
Section that are approved and labeled. 1.1 The Terms Classified pertaining to cable trays (rather than Listed) and "Labeled": As defined in NFPA 70, Article 100, including painted trays. 1.2 Listing and Labeling Agency Qualifications: A "Nationally Recognized Testing Laboratory" as defined in OSHA Regulation 1910.7.

PRODUCT DATA SHEET 2 - Comply with NFPA 70, National Electrical Code, Article 392: Cable Trays;
provide UL Classification and labels.

PRODUCT DATA SHEET 3 - Comply with IEC 61537, Cable Tray Systems and Cable Ladder Systems for
Cable Management.

PRODUCT DATA SHEET 4 - Comply with NEMA VE 1/CSA C22.2 No. 126.1, Metal Cable Tray Systems,
for materials, sizes, and configurations; provide cCSAus Certificate and labels. PRODUCT DATA SHEET 5 - Provide documentation of the following certifications: 5.1 ISO 9001 quality certification. 5.2 American Bureau of Shipping (ABS) Product Design Assessment certification. 5.3 Det Norske Veritas (DNV) certification. 5.4 E 90 Fire Testing certification. 5.5 VDE certification.

PRODUCT DATA SHEET 6 - Provide ETL test documentation showing cable compression/deformation
testing. PRODUCT DATA SHEET 7 - Provide military test documentation showing compliance with the following standards: 7.1 MIL-S-901D (Navy) Military Specification, Requirements for Shock Tests, High Impact; Shipboard Machinery, Equipment and Systems 7.2 MIL-STD-167-1 (Ships) Military Standards Mechanical Vibrations of Shipboard Equipment

SCHEDULE 5 - COORDINATION PRODUCT DATA SHEET 0 - Coordinate layout and installation of cable tray with other installations. CABLE TRAYS 16139 - 3

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
0.1 Revise locations and elevations from those indicated as required to suit field conditions and as approved by the Architect. Storage and Handling: Avoid breakage, denting and scoring finishes. Damaged products will not be installed. Store cable trays and accessories in original cartons and in clean dry space; protect from weather and construction traffic. Wet materials will be unpacked and dried before storage.

0.2

PART 2 - PRODUCTS

SCHEDULE 0 - MANUFACTURERS: Subject to compliance with requirements, provide products by the

following:

PRODUCT DATA SHEET 0 - Cablofil, Inc., 8319 State Route 4, Mascoutah, IL, 62258. Phone: (618) 5663230. Toll-Free: [email protected]. (800) 658-4641. Fax: (618) 566-3250. Website: www.cablofil.com. Email:

PRODUCT DATA SHEET 1 - [Approved Alternates: Select one of the following, if applicable.] 1.1 [Hoffmann] 1.2 [P-W Industries] 1.3 [Black Box Corporation] 1.4 [Code Electric] SCHEDULE 1 - MATERIALS AND FINISHES: PRODUCT DATA SHEET 0 - Cable Tray Materials: select one of the following: 0.1 [Carbon steel wire, ASTM A 510, Grade 1008. Wire welded, bent, and surface treated after 0.2
manufacture.] OR [Stainless steel wire, AISI 304L or AISI 316L, 2B, finished cold drawn wire.]

PRODUCT DATA SHEET 1 - Cable Tray Finishes: 1.1 Finish for Carbon Steel Wire after welding and bending of mesh; select one of the following: A. [Electrodeposited Zinc Plating: ASTM B 633, Type III, SC-1.] B. [Hot-Dip Galvanizing After Fabrication: ASTM A 123.] C. [Powder-Coated:] 1. [Black powder-coated surface treatment over Electrodeposited Zinc Plating (or plain steel) using ASA 61 black polyester coating.] 2. [Custom Color Powder-Coated surface treatment over Electrodeposited Zinc Plating (or plain steel). Contact Cablofil for color information.] 1.2 Finish for Stainless Steel Wire: According to ASTM B 380.

PRODUCT DATA SHEET 2 - Cable tray will consist of continuous, rigid, welded steel wire mesh cable
management system, to allow continuous ventilation of cables and maximum dissipation of heat, with UL Classified splices where tray(including UL Classified painted tray) acts as Equipment Grounding Conductor (EGC). Wire mesh cable tray will have continuous Safe-T-Edge T-welded top side wire to protect cable insulation and installers.

CABLE TRAYS

16139 - 4

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
PRODUCT DATA SHEET 3 - Provide splices, supports, and other fittings necessary for a complete, continuously grounded system. 3.1 3.2 3.3 Mesh: 2 x 4 inches (50 x 100 mm). Straight Section Lengths: 118 inches (3,000 mm). Wire Diameter: Patented design includes varying wire sizes to meet application load requirements; to optimize tray strength; and to allow tray to remain lightweight. Safe-T-Edge: Patented Safe-T-Edge technology on side wire to protect cable insulation and installers hands. Fittings: Wire mesh cable tray fittings are field-fabricated from straight tray sections, in accordance with manufacturers instructions and Item 2.3. CF Series Cable Tray Size:

3.4 3.5 3.6 A.

Depth: Cable tray depth will be (unless otherwise shown on drawings): 1. [1 inch (30 mm)] 2. [2 inches (54 mm)] 3. [4 inches (105 mm)] 4. [6 inches (150 mm)] Width: Cable tray width will be (unless otherwise shown on drawings): 1. [2 inches (50 mm)] 2. [4 inches (100 mm)] 3. [6 inches (150 mm)] 4. [8 inches (200 mm)] 5. [12 inches (300 mm)] 6. [18 inches (450 mm)] 7. [20 inches (500 mm)] 8. [24 inches (600 mm)] Length: Cable tray section length will be 118 inches (3000mm) unless otherwise shown on drawings. Fill Ratio: Cable tray may be filled to [40%] [50%] [60%] [100%] of total fill capacity. Size cable tray to accommodate future cabling changes or additions. Load Span Criteria: 1. Install and support cable management system in accordance with one of the following: a. [IEC 61537, with load span criteria of L/200 (to exceed standard requirements of L/100) and a Safety Factor of 1.7] OR b. [NEMA VE-1 (2002), with Safety Factor of 1.5] 2. Cable tray will be capable of carrying a uniformly distributed load of ______ pounds per foot on a ______ support span, according to load tests of standard shown in Item A above. Other cable tray options; select if applicable:

B.

C. D.
E.

3.7

CABLE TRAYS

16139 - 5

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com A.
[Cablofil Easy Pack: Ready-to-install 78 (2000mm) lengths of CF Series Cable Tray with Preclick Splices and all associated hardware.] 1. [PACKCF 54/50: 2 inches (50mm) x 2 inches (50mm)] 2. [PACKCF 54/100: 2 inches (50mm) x 4 inches (100mm)] 3. [PACKCF 54/150: 2 inches (50mm) x 6 inches (150mm)] 4. [PACKCF 54/200: 2 inches (50mm) x 8 inches (200mm)] 5. [PACKCF 54/300: 2 inches (50mm) x 12 inches (300mm)] [CFG Series: G-shaped cable tray for direct attachment or for use in small spaces.] 1. [CFG 50/100: 2 inches (50mm) x 4 inches (100mm)] 2. [CFG 50/200: 2 inches (50mm) x 8 inches (200mm)] 3. [CFG 100/150: 4 inches (100mm) x 6 inches (150mm)] [FCF Fasclic Series: CF Series Cable Tray with pre-mounted fast splice.] 1. [FCF 54/50: 2 inches (54mm) x 2 inches (50mm)] 2. [FCF 54/100: 2 inches (54mm) x 4 inches (100mm)] [CFL Series: CF Series Cable Tray with one bend for beam attachment.] 1. [CFL 54/100: 2 inches (54mm) x 4 inches (100mm)] [Telex Rail: TXF Series Cable Tray; cover and supports also available.] 1. [TXF 35: 1 inch (25mm) x 1 inch (25mm)]

B.

C.

D. E.

SCHEDULE 2 - CABLE TRAY SUPPORTS & ACCESSORIES PRODUCT DATA SHEET 0 - Fittings/Supports: Wire mesh cable tray fittings are field-fabricated from
straight tray sections, in accordance with manufacturers instructions. Supports will include the FAS (Fast Assembly System) where possible so that screws, bolts, and additional tools are not required for cable tray mounting; installation time is reduced; and tray path can adapt to installation obstacles without the need for additional parts. Place supports so that support span does not exceed that shown on the drawings.

0.1 A. B. C.
D.

Ceiling-mounted; select one of the following support methods to mount from ceiling structure with , 3/8 or threaded rod, if applicable: [SF 50, SF 100: Center-mount 2(50mm) or 4 (100mm)-wide tray without nuts & bolts; fits rod.] [PAT 30: Bolt to UC 50 to center-mount 2 (50mm)-wide tray without nuts & bolts; fits rod.] [SAS Suspension Hanger: Center-mount 4 (100mm) or 6 (150mm)-wide tray without nuts & bolts; fits rod.] [FAS P Center Hanger: Center-mount tray without nuts & bolts.] 1. [FAS P CH 200: 8 inches (200mm)] 2. [FAS P CH 300: 12 inches (300mm)] 3. [FAS P CH 400: 16 inches (400mm)] 4. [FAS P CH 450: 18 inches (450mm)] 5. [FAS P CH 500: 20 inches (500mm)] 6. [FAS P CH 600: 24 inches (600mm)]

CABLE TRAYS

16139 - 6

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com E.
[FAS Profile: Trapeze-mount tray without nuts & bolts; fits rod.] 1. [FAS P 150: 6 inches (150mm)] 2. [FAS P 200: 8 inches (200mm)] 3. [FAS P 300: 12 inches (300mm)] 4. [FAS P 400: 16 inches (400mm)] 5. [FAS P 450: 18 inches (450mm)] 6. [FAS P 500: 20 inches (500mm)] 7. [FAS P 600: 24 inches (600mm)] 8. [FAS P 700: 28 inches (700mm)] 9. [FAS P 1000: 40 inches (1000mm)] 10. [FAS P 2000: 78 inches (2000mm)] 11. [FAS P 3000: 118 inches (3000mm)] [AS Trapeze Hanging Clip:Trapeze-mount tray without nuts & bolts.] [PROCS Standard Profile: Trapeze-mount tray; fits rod.] 1. [PROCS 1000: 40 inches (1000mm)] 2. [PROCS 2000: 78 inches (2000mm)] 3. [PROCS 3000: 118 inches (3000mm)] [FAS C Bracket: mounting holes; support multiple trays or stack supports.] 1. [FAS C 100: 4 inches (100mm)] 2. [FAS C 150: 6 inches (150mm)] 3. [FAS C 200: 8 inches (200mm)] 4. [FAS C 300: 12 inches (300mm)] 5. [FAS C 400: 16 inches (400mm)] 6. [FAS C 450: 18 inches (450mm)] [CSC Bracket: Requires nuts & bolts to support multiple trays or stack supports.] 1. [CSC 100: 4 inches (100mm)] 2. [CSC 200: 8 inches (200mm)] 3. [CSC 300: 12 inches (300mm)] [CS Standard L Bracket: Requires nuts & bolts to mount tray to ceiling.] 1. [CS 100: 4 inches (100mm)] 2. [CS 200: 8 inches (200mm)] 3. [CS 300: 12 inches (300mm)] 4. [CS 400: 16 inches (400mm)] 5. [CS 500: 20 inches (500mm)] 6. [CS 600: 24 inches (600mm)] [EDF Rail: To mount FAS Universal Brackets from ceiling or to trapeze-mount tray.] 1. [EDF 300: 12 inches (300mm)] 2. [EDF 600: 24 inches (600mm)] 3. [EDF 1000: 40 inches (1000mm)] 4. [EDF 2/3000: 118 inches (3000mm)] [EDF Ceiling Supports:] 1. [PFREDF Mounting Bracket: To ceiling-mount EDF without hardware.]

F.

G.

H.

I.

J.

K.

L.

CABLE TRAYS

16139 - 7

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
2. 3. [DF Angle Mounting Bracket: To mount to angled ceilings.] [ERD 10 Brace Plate: To mount double-sided EDF assemblies.]

0.2 A.

Wall-mounted; select one of the following support methods, if applicable: [FAS Profile: mounting holes attach tray vertically or horizontally to wall.] 1. [FAS P 150: 6 inches (150mm)] 2. [FAS P 200: 8 inches (200mm)] 3. [FAS P 300: 12 inches (300mm)] 4. [FAS P 400: 16 inches (400mm)] 5. [FAS P 450: 18 inches (450mm)] 6. [FAS P 500: 20 inches (500mm)] 7. [FAS P 600: 24 inches (600mm)] 8. [FAS P 700: 28 inches (700mm)] 9. [FAS P 1000: 40 inches (1000mm)] 10. [FAS P 2000: 78 inches (2000mm)] 11. [FAS P 3000: 118 inches (3000mm)] [FV-1 Vertical Bracket: Heavy-duty support for vertical trays.] [FAS L Bracket: mounting holes.] 1. [FAS L 100: 4 inches (100mm)] 2. [FAS L 150: 6 inches (150mm)] 3. [FAS L 200: 8 inches (200mm)] 4. [FAS L 300: 12 inches (300mm)] 5. [FAS L 400: 16 inches (400mm)] 6. [FAS L 450: 18 inches (450mm)] [FAS C Bracket: mounting holes; support multiple trays or stack supports.] 1. [FAS C 100: 4 inches (100mm)] 2. [FAS C 150: 6 inches (150mm)] 3. [FAS C 200: 8 inches (200mm)] 4. [FAS C 300: 12 inches (300mm)] 5. [FAS C 400: 16 inches (400mm)] 6. [FAS C 450: 18 inches (450mm)] [FAS Universal Bracket: Mount tray to walls or channel framing.] 1. [FAS U 100: 4 inches (100mm)] 2. [FAS U 150: 6 inches (150mm)] 3. [FAS U 200: 8 inches (200mm)] 4. [FAS U 300: 12 inches (300mm)] 5. [FAS U 400: 16 inches (400mm)] 6. [FAS U 500: 20 inches (500mm)] 7. [FAS U 600: 24 inches (600mm)] [EDF Rail: To mount FAS Universal Brackets] 1. [EDF 300: 12 inches (300mm)] 2. [EDF 600: 24 inches (600mm)] 3. [EDF 1000: 40 inches (1000mm)] 4. [EDF 2/3000: 118 inches (3000mm)]

B. C.

D.

E.

F.

CABLE TRAYS

16139 - 8

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com G.
[CS Standard L Bracket: Requires nuts & bolts to mount tray to wall.] 1. [CS 100: 4 inches (100mm)] 2. [CS 200: 8 inches (200mm)] 3. [CS 300: 12 inches (300mm)] 4. [CS 400: 16 inches (400mm)] 5. [CS 500: 20 inches (500mm)] 6. [CS 600: 24 inches (600mm)] [CSC Bracket: Requires nuts & bolts to support multiple trays or stack supports.] 1. [CSC 100: 4 inches (100mm)] 2. [CSC 200: 8 inches (200mm)] 3. [CSC 300: 12 inches (300mm)] [CRP Bracket: Heavy-duty hot-dip galvanized bracket.] 1. [CRP 100: 4 inches (100mm)] 2. [CRP 150: 6 inches (150mm)] 3. [CRP 200: 8 inches (200mm)] 4. [CRP 300: 12 inches (300mm)] 5. [CRP 400: 16 inches (400mm)] 6. [CRP 500: 20 inches (500mm)] 7. [CRP 600: 24 inches (600mm)] [UC 50 Cable Tray Standoff: To mount 2 (50mm)-wide tray; no hardware required.] [CAT 30/41 Snap-In or Strut-Mount Support: To mount 2 (50mm)-wide tray; no hardware required.] [C 50 Cable Tray Support: To mount 2 (50mm) or 4 (100mm)-wide tray; no hardware required.] Underfloor supports; select one of the following support methods, if applicable: A. [UFC Underfloor Clamp: Use with FAS L Bracket or FAS Profile to mount tray to floor post(s).] [FAS Profile: mounting holes to attach directly to floor without additional hardware, or to secure tray to floor post(s) with UFC Underfloor Clamp.] 1. [FAS P 150: 6 inches (150mm)] 2. [FAS P 200: 8 inches (200mm)] 3. [FAS P 300: 12 inches (300mm)] 4. [FAS P 400: 16 inches (400mm)] 5. [FAS P 450: 18 inches (450mm)] 6. [FAS P 500: 20 inches (500mm)] 7. [FAS P 600: 24 inches (600mm)] 8. [FAS P 700: 28 inches (700mm)] 9. [FAS P 1000: 40 inches (1000mm)] 10. [FAS P 2000: 78 inches (2000mm)] 11. [FAS P 3000: 118 inches (3000mm)] [UFCN Underfloor Clamp with FAS Profile: To mount tray to floor post without additional hardware.] 1. [UFCN 150: 6 inches (150mm)] 2. [UFCN 200: 8 inches (200mm)]

H.

I.

J. K. L. 0.3

B.

C.

CABLE TRAYS

16139 - 9

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
3. D. [UFCN 300: 12 inches (300mm)]

[EDF Rail: To mount FAS Universal Brackets or FAS L Brackets] 1. [EDF 300: 12 inches (300mm)] 2. [EDF 600: 24 inches (600mm)] 3. [EDF 1000: 40 inches (1000mm)] 4. [EDF 2/3000: 118 inches (3000mm)] [DF Support: To mount EDF Rail to floor.] [[FAS Universal Bracket: Mount tray to EDF Rail underfloor without additional hardware.] 1. [FAS U 100: 4 inches (100mm)] 2. [FAS U 150: 6 inches (150mm)] 3. [FAS U 200: 8 inches (200mm)] 4. [FAS U 300: 12 inches (300mm)] 5. [FAS U 400: 16 inches (400mm)] 6. [FAS U 500: 20 inches (500mm)] 7. [FAS U 600: 24 inches (600mm)] [FAS L Bracket: Mount tray to EDF Rail underfloor without additional hardware.] 1. [FAS L 100: 4 inches (100mm)] 2. [FAS L 150: 6 inches (150mm)] 3. [FAS L 200: 8 inches (200mm)] 4. [FAS L 300: 12 inches (300mm)] 5. [FAS L 400: 16 inches (400mm)] 6. [FAS L 450: 18 inches (450mm)] [UFS 60/100 Underfloor Stand: 2.4 (60mm)-high stand mounts directly to floor without additional hardware.] [UFS 150/200 Underfloor Stand: 6 (150mm)-high stand mounts directly to floor without additional hardware.] [UC 50 Cable Tray Standoff: Mounts 2 (50mm)-wide tray directly to floor without additional hardware.] [C 50 Cable Tray Support: Mounts tray directly to floor without additional hardware.] Splices, including those approved for electrical continuity (bonding), as recommended by cable tray manufacturer. Select one of the following splicing methods, if applicable:

E.

F.

G.

H. I. J. K. 0.4
A. B. C. D.

[UL Classified EDRN Fast Splice: No hardware required] [UL Classified SWK Splice Washer Kit: Swaged set for splicing, turns, bends, tees] [UL Classified ED Universal Splice Bar: Cut & bend to fit any configuration] [Preclick Splice: Bolted connection optional] [UL Classified EDT Splice Plate: Bolted connection]

E.

CABLE TRAYS

16139 - 10

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
F. [UL Classified CE 25 & CE 30 Square Splice Washers: Use with EZ BN Nut & Bolt] [UL Classified CE 40 Square Splice Washer: Use with EZ BN to splice trays on bends, adjustable tees] [FASLock Splice: For sweeps and bends with tray 12 (300mm) and wider.] [UL Classified EZ T 90 kit: For Tees and 90s] [UL Classified RADT90 kit: For radius Tees and 90s] Accessories: As required to protect, support, and install a cable tray system. Select from the following accessories, if applicable:

G. H. I. J. 0.5 A.

[CVN Covers, of same material and finish as cable tray; with optional cover clips.] 1. [CVN 50, 2 inch (50mm)] 2. [CVN 100, 4 inch (100mm)] 3. [CVN 150, 6 inch (150mm)] 4. [CVN 200, 8 inch (200mm)] 5. [CVN 300, 12 inch (300mm)] 6. [CVN 450, 18 inch (450mm)] 7. [CVN 500, 20 inch (500mm)] 8. [CVN 600, 24 inch (600mm)] [COT Divider Strips, of same material and finish as cable tray.] 1. [COT 30, 1 inch (30mm)] 2. [COT 54, 2 inch (54mm)] 3. [COT 105, 4 inch (100mm)] 4. [COT 150, 6 inch (150mm)] [Cable Routing Accessories:] 1. [Dropout: Bolt to tray; slotted design.] 2. [Cablexit: No additional hardware needed.] [Support Accessories:] 1. 2. 3. 4. 5. [FS 41: Fastrut connector to mount tray to unistrut without additional hardware.] [EZJB 5/16: J-Bolt kit to mount tray to 19 or 23 racks with FAS Profile.] [Gripple: Wire Cable Hanging Support.] [HB-2: Wall Termination Bracket] [Beam Supports:]

B.

C.

D.

a.

[EZ BC Beam Clamp: To clamp threaded rod to beam.] 1) [EZ BC : For threaded rod.] 2) [EZ BC 3/8: For 3/8 threaded rod.]

CABLE TRAYS

16139 - 11

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
3) [EZ BC : For threaded rod.] a. [ETC Beam Clamp: To clamp tray to beam without additional hardware.] 1) [ETC 20: 0.8 inch (20mm)] 2) [ETC 30: 1 inch (30mm)]

6. [EF Beam Support: Clamp tray to beam or trapeze-mount tray below beam.]
a. b. [EF 11/400: 16 inches (400mm)] [EF 15/600: 24 inches (600mm)]

7.

[Supports for Conduit, Boxes, Cables and other Equipment:] a. [C 50: To mount Electrical Boxes to tray without additional hardware.] b. [SBD: To mount Boxes or Conduit to tray without additional hardware.] c. [MFM Multifix Metal Plate: For cable bundling, tubing or light support.] d. [EZVC: x 15 Velcro Roll to bundle cables.]

E. F. G.

[GNDCL: Grounding Clamp to ground cable tray.] [SZMC Kit: Seismic Bracing Kit; space 30 apart for most seismic conditions. Consult Cablofil for additional information.] [FAS Roller: Cable Pulling Kit; set of 6 rollers.] [EZ CL: Cable Label Clip to organize cables by color.] 1. [CLIPBLACK] 2. [CLIPWHITE] 3. [CLIPORANGE] 4. [CLIPYELLOW] 5. [CLIPGREEN] 6. [CLIPBLUE] 7. [CLIPGRAY]

H.

SCHEDULE 3 - EQUIPMENT GROUNDING CONDUCTOR FUNCTION & GROUNDING

PRODUCT DATA SHEET 0 - UL Classified cable trays may act as Equipment Grounding Conductors.
Contact Cablofil for approved sizes.

0.1
A. B.

Use UL Classified splicing methods as recommended by Cablofil. Ground cable trays at end of continuous run. Ground continuous cable tray runs every 60 feet. Cable trays that are not UL Classified will be grounded per NEC requirements and manufacturer recommendations. Ground cable trays against fault current, noise, lightning, and electromagnetic interference by mounting grounding wire to each 10 cable tray section with grounding clamp, Cablofil Model GNDCL.

0.2 A.

PART 3 - EXECUTION

CABLE TRAYS

16139 - 12

Cablofil, Inc. 8319 State Route 4 Mascoutah, IL 62258 USA Phone (618) 566-3230 Toll Free (800) 658-4641 Fax (618) 566-3250 www.cablofil.com
SCHEDULE 0 - EXAMINATION:

PRODUCT DATA SHEET 0 - Examine substrates for compliance with requirements for installation
tolerances and other conditions affecting performance of cable trays. Do not proceed with installation until unsatisfactory conditions have been corrected. SCHEDULE 1 - INSTALLATION

PRODUCT DATA SHEET 0 - Install cable tray level and plumb according to manufacturer's written
instructions, Coordination Drawings, original design, and referenced standards.

0.1 A.
B. C.

Cutting: Field-fabricate changes in direction & elevation by cutting & bending cable tray. Cut cable tray wires in accordance with manufacturers instructions. Cable tray wires must be cut with side-action bolt cutters with offset head to ensure integrity of protective galvanic layer. Remove burrs and sharp edges from cable trays. Certified Installers: Cable tray installers must have successfully completed Cablofils Certified Installer program. END OF SECTION 16139

0.2

CABLE TRAYS

16139 - 13