Physical - Phenomenon And'its Applications To Telegraphy, Telephony - A Johnsen K Rahbek
Physical - Phenomenon And'its Applications To Telegraphy, Telephony - A Johnsen K Rahbek
Physical - Phenomenon And'its Applications To Telegraphy, Telephony - A Johnsen K Rahbek
713
In the course of some experiments in telephony, the authors discovered in 1917 that in some cases an appreciable adhesion occurs between two. bodies in contact with each other, when a difference of electrical potential exists between them. Leading up to this discovery and its later development by the authors was the observation that a weak sound was produced when a finger was rubbed lightly on a metal surface while an alternating current of audio frequency was passing between the finger and the metal. Later investigations by the authors and others have shown that the latter phenomenon has been observed by numerous persons, especially in recent times, when, in consequence of the wide application of alternating current, the phenomenon has been observed on numerous occasions. These observations, however, have generally been disregarded, and no systematic investigation of the true nature of the phenomenon seems to have been carried out. The only suggestion of practical use seems to be due to the well-known American inventor, Dr. Elisha Gray, who in 1875 patented the use of a rotating metal drum which would reproduce sound when touched by the operator's finger. Immediately after their observation of this phenomenon the authors commenced a series of experiments with different materials, and soon attained such powerful and distinct effects that a systematic investigation of the true nature and the necessary conditions for the production of the phenomenon was decided upon. During this investigation, which was successfully completed in 1918, several possibilities of the practical application of the effect suggested themselves to the authors, who devoted the following two years to the technical design of various apparatus based on this effect, chiefly for use in telegraphy and telephony, as well as to the solution of certain technical problems which soon presented themselves in this connection. Ultimately, in 1920, apparatus was produced which was extremely reliable and constant in action, and this was for the first time described and exhibited in Copenhagen in 1920, at the electrotechnical congress held on the occasion of the centenary of the discovery of electromagnetism by Oersted. The most remarkable feature of this apparatus, chiefly telegraphrrecorders and loudspeaking telephones, is constituted by the fact that, although powerful mechanical effects are produced by such apparatus, the current consumption is practically nil.
The production of sound when one's finger rubs a metal plate can be shown to be due to a variable adhesion between the finger and the metal. The natural adhesion" is increased when the current is passing, and the direction of the current is in this case of no importance. With a pure alternating current a note is therefore heard which is one pctave higher than that produced in an ordinary (polarized) telephone by the same alternating current. This " electrical adhesion " can, by means of other materials than the finger and by the application of direct current, be demonstrated in a continuous and highly intensified form, as shown in the following experiment. This illustrates the very considerable adhesion set up between a metal plate and a slab of lithographic stone, if the two parts are connected to a 440-volt d.c. supply. Plane, polished
d.c.
FIG.
1.
lithographic stone brought into contact with plane, polished metal shows the electrical adhesion in a much higher degree than does the human skin in contact with metal.
Experiment.A slab of lithographic stone about 2 inches thick (see Fig. 1) is placed on a table. The underside of the stone is covered with metal foil,'(as a cement for fastening the foil, fish-glue or, better, water-glasV may be used). It is essential that the cement should not possess highly insulating properties, as, for instance, shellac and most varnishes do. The upper surface of the stone is plane and very smooth," preferably polished, and on this is placed a plane, polished disc of metal (brass) 2 inches in diameter. If the metal foil' on the-underside and the metal disc are connected to a source of E.M.F. (440 volts d.c), the disc will cling tightly to the stone. By means of a scale balance it can be shown that more than one kilogram is necessary to separate the disc. from the stone. An equally large force is necessary to move the disc alongthe surface of tne^storie, thus showing that a considerable friction has been set up between them. The electrical resistance of the stone is very'high, and therefore the current passing between the stone-and the disc is very' small, in spite of the high voltage applied". As the stone1
* The commercial exploitation of the subject-matter of the Lecture is protected by British Patents 144 761, 146 747, 194 747, and by Colonial and Foreign Patents. I.E.E. JOURNAL, VOL. 61, No. 320, JULY 1923.
48
714
possesses some hygroscopic properties, its conductivity is dependent on the humidity of the surrounding air, so that an exact value of the current cannot be given ; moreover different specimens show different conductivities. Generally, hoWever, the current will not exceed a few microamperes. That this is so can be shown by the fact that there is no perceptible diminution of the adhesion when the current is passed through the body of the operator. If the circuit is broken, the adhesion disappears. It is obvious that there are some points of resemblance between this device and an electromagnet. Both have the property of producing mechanical force by means of electricity. The very small current sufficient for the operation shows that the adhesive effect can, in certain cases, be used with advantage instead of electromagnetism. An essential difference, however, lies in the fact that an electromagnet is able to attract its armature from some distance, and thus do mechanical work, whereas the electric adhesion is only manifest between two surfaces which are in,'Contact with each other. It is true that if one of the surfaces is elastic and only partially in contact with.the other before the E.M.F. is applied, a certain small amount of mechanical work can be effected, as will be shown later, but generally the utilization of the electrical adhesion is confined to the governing of extraneous forces, and its use will be advantageous where only small currents are available for this purpose, and also where relatively large forces are to be exerted on bodies of small mass. While the attraction exerted by an electromagnet on its armature is, within limits, proportional to the mass of the latter, the electrical adhesion is independent of the thickness of the metal: a thin, 'light metal foil will adhere to the stone quite as well as a thick, heavy disc. The principal explanation of the nature of the electric adhesion, as given by the authors in 1917, is as follows : The lithographic stone belongs to a class of substances which will here be termed semi-conductors. These substances are solid electrolytic conductors, and they combine a moderate internal resistance with a relatively high contact resistance to conducting solid bodies applied to their surface, if no conducting liquid, cement or the like is interposed between the surfaces. The true nature of the contact resistance proper has not yet been completely revealed, but it appears that the very thin film of absorbed air which ordinarily covers the surface of solid bodies plays a certain role, as does the fact that two solid bodies are in reality in contact in relatively very few points, even if the greatest care is taken to fit them exactly together. It may be mentioned that the contact resistance exists even with thin, bright tinfoil which is smoothed very carefully on the semi-conductor, while it is absent with mercury. Further, it appears that a relatively large potential difference is necessary to draw electrolytic ions, which in this case are the only carriers of the current, across even the. smallest air space, while electrons pass freely across even a light metallic contact. That the majority of the ions have to cross} a certain free space at the point of contact is also made probable by the fact that the value of the contact resistance is by no means constant, but decreases with increasing potential difference'. Indeed, the current is over a wide range nearly,
FIG.
2. '
easily be verified experimentally by means of an electrostatic voltmeter. It is obvious therefore that there must be a very large electrostatic attraction between the semi-conductor and each of the plates, if it is remembered that the attraction between the two plates of an air condenser is inversely proportional to the square of the distance between the plates, the potential difference being maintained constant. The air-gap being in this case theoretically infinitesimal, an infinitely large attraction should be expected. In practice, however, only a limited attraction is manifested, but, nevertheless, an unusually strong attraction can be obtained with relatively moderate potentials. The attraction is, as has already been mentioned, also manifested by an increase of the friction between H and each of the plates I and II. If a sufficiently high potential difference be applied, a considerable force is necessary to cause I or II to slide on H. It is especially this increase of friction that has been utilized
715
albumen, etc., which swell more or less when immersed in water, and which also lose their conductivity nearly completely if heated sufficiently in the dry state. On this chief group of semi-conductors a flow of current through the material has much the same effect as heat on the conductivity. If a constant potential is applied the current will steadify diminish, the moisture being, in the vicinity of the electrodes, gradually decomposed by electrolysis. When an appreciable layer next to the electrodes has thus been dried, a considerable diminution of the surface attraction is observed, and ultimately the attraction will practically disappear in the course of some hours or days, according to the circumstances. On the other hand, the conductivity and consequently the full attractive power will be
FIG.
3.
restored if the material is left to itself for a day or two. How this inconstancy has been eliminated in the practical apparatus will be described later. If one of the metal plates (II in Fig. 1) is connected to the semi-conductor by means of a sufficiently conducting cement or glue, the contact resistance, and consequently the drop of potential, will almost entirely disappear at this place. As shown in Fig. 3, nearly the full potential. will appear between the other plate, I, and the semi-conductor ; the interior drop of potential p' is ordinarily only some few per cent, sometimes a fraction per cent, of the total potential E. The values of P, p, P' and p' in Figs. 2 and 3 only correspond if the value of the contact resistance between H. and I is assumed to be independent of the drop of potential, but this is, in reality, not the case. It is obvious that a larger attraction is obtained between I and H in the case illustrated in Fig. 3'than in that shown in Fig. 2'; in the actual apparatus the contact resistance between the semi-conductor and one
716
of the electrodes is, for this reason, eliminated as far as possible. As only a relatively small drop of potential exists in the interior of the semi-conductor, the thickness of the latter has little bearing on the magnitude of the attraction. Indeed, the lithographic stone would give very nearly the same attraction if its thickness, instead of being 2 inches, were only a fraction of an inch. It is, of course, a practical advantage that a fairly thick and therefore robust semi-conductor can be used. This point is particularly emphasized because attempts have previously been made by others to construct electrostatic relays by the insertion of a thin dielectric between two conducting plates. As, however, the attraction across a dielectric is inversely proportional to the square of the thickness of the latter, an extremely thin layer of dielectric (1/2 000 inch or less) has to be used in order to obtain a reasonable sensitivity, and thus the dielectric in such apparatus is very delicate and liable to be punctured. The earliest apparatus of this description appears to be due to the American inventor R. A. Fessenden, who used mica as a dielectric in a telegraphrecorder, which was operated by means of alternating current. It is not possible to operate such apparatus by means of direct current, as a surface charge (similar to the well-known residual charge in mica condensers) will in a short time collect on the dielectric and coun-
FIG.
4.
teract the attraction across the latter. This again, means that telephonic apparatus cannot be developed on this principle, as a continuous polarization potential is necessary in all electrostatic telephones. The general arrangement of the semi-conductor in relays, etc., is shown diagrammatically in Fig. 4. The cylindrical semi-conductor, H, is mounted on a shaft and is kept in continuous rotation by means of a motor (not shown) ; the direction of rotation is indicated by the arrow. Round a part of the circumference of the semi-conductor is placed a metal band, I, which at the point, a, is connected to a spring, S. A weaker spring, s, serves to keep the band, I, taut. Inside the semi-conductor is shown the metal lining, II, which is to be cemented to the semi-conductor. In reality, this metal lining is in our more recent apparatus replaced by a
this spring will contract if the potential difference decreases or disappears entirely. The members to be operated by the relay may thus be coupled to the point,* a, where the band is connected to the spring, S. This arrangement forms the basis of a number of different apparatus. If the point, a, is connected to a recording stylus, an ink siphon or the like, the apparatus may be used for receiving telegraph messages, and if relay contacts are operated in the same way the apparatus forms a telegraph transmitting relay which may be used either for receiving or transmitting purposes. If the spring, S, is replaced by the diaphragm of a sound-box, the apparatus may be used as a loudr speaking telephone. Instead of a cylindrical semi-conductor encircled by
717
of a hollow cylinder, in which water or an aqueous solution was present, absorb and remain soaked with the water or the solution without their exterior surface becoming moist. Agate (but not- slate, lithographic stone, etc.) shows this quality in a very pronounced degree. This material is unable to absorb any large percentage of water, so that its conductivity is not excessive even if it is fully soaked with moisture ; on the other hand, when current is passed through it the small percentage of moisture on the surface disappears rapidly. If a hollow cylinder of agate is filled with suitable electrolyte, moisture will, however, diffuse from the interior to the point where the metallic conductor touches the outer surface, and this is sufficient to prevent the conductivity near the surface from decreasing below a certain value. This diffusion is, however, so slow that the outside of the agate cjdinder keeps perfectly dry on account of the evaporation. On the other hand, only the moisture which, by slow diffusion, has actually reached the surface will be evaporated, as practically no circulation of air can take place inside the extremely fine pores. The loss of moisture by evaporation is therefore extremely small, in spite of the stone being in reality entirely and continuously soaked with moisture. In our actual apparatus such hollow agate cylinders are used. These cylinders are mounted between two bosses on a shaft, so that a space for the liquid is formed between the shaft and the interior surface of the cylinder. The shaft and bosses are silvered in order to prevent corrosion. The electrolyte is substantially a solution of a somewhat hygroscopic salt, which will not easily crystallize in the pores of the agate. It has been found that the formation of crystals in the pores of the agate will produce partial cracks and ultimately cause the stone to disintegrate. The loss of electrolyte by evaporation and electrolysis is extremely small, the average life of the filling being at least two years, after which time the cylinder can be refilled in a few minutes. If desired, the electrolyte can be taken up by some absorbent powder such as flour, as is done in dry cells. In order to prevent the electrolytic formation of free hydrogen inside the sealed cylinder, the shaft of which is ordinarily the cathode, an oxidizing substance such as manganese peroxide is added to the electrolyte. In the foregoing remarks, the authors have not dealt with the influence of the polarity of the semi-conductor on the contacting conductor. If both the internal resistance and the surface resistance of the semi-conductor are independent of the polarity of current and potential, it is to be expected that the attraction will be substantially independent of the polarity, and this is verified by experiment. These conditions can be approximately realized by means of a dry lithographic stone, as has been shown, especially if the stone is heated a little above the air temperature. Upon reversal of the polarity, the current and the attraction will be found to have remained approximately constant. If, however, the semi-conductor contains a considerable amount of moisture, or if it has been impregnated with an electrolytic salt solution and especially if it is hollow and filled with an electrolytic fluid, as the agate cylinder above described, the effect of reversal of polarity is very
718
marked. If the semi-conductor is made negative relative to the contacting conductor; the current will, after the application of a constant potential difference, gradually decrease, but only to a certain extent in the case of the filled agate cylinder, as already mentioned. On the other hand, the attraction will remain substantially constant from the first moment, a small increase being, however, observed in the course of the first few minutes if certain electrolytes are used. In the actual apparatus the semi-conductor is made negative, and is so chosen as to give a sufficiently constant attraction for practical purposes. The constant potential necessary for constant attraction is generally easily attained in spite of the inevitable variation of current, as the total current consumption is so small that it constitutes only a negligible load, even on high-resistance circuits. If the semi-conductor is made positive relative to the contacting conductor, the current will gradually increase after the application of the potential, and the attraction will generally be found after a few minutes to have decreased considerably. In this case the interior resistance of the semi-conductor remains substantially constant, but the contact resistance gradually diminishes until finally only a very small drop of potential exists at the surface. In some cases the attraction will practically decrease to zero in a few minutes, while the current increases to more than 20 times its original value. If the potential is reversed, the original small current and corresponding large attraction do not reappear immediately, but generally in less than one minute. The cause of the reduction of contact resistance just described has not yet been exactly stated by the authors. It is certainly due to the flow of current; and it appears that moisture is carried with the current to the surface of the semi-conductor, the effect being probably intimately related to electro-capillarity. It may be mentioned that the effect has been observed both with acid and alkaline impregnation of the semi-conductor. In connection with this question, a reference to the Edison Electromotograph may be appropriate. This apparatus, which aroused considerable interest in the 'seventies of the last century, has some constructive resemblance to the arrangement described in connection with Fig. 4. Used as a telephone it consists materially of a rotating, porous chalk cylinder, which is entirely soaked with an electrolyte and the surface of which is kept constantly wet,' the latter being the exact reverse of the conditions necessary for electrostatic attraction as described by the authors. The end of a flat, elastic metal strip carrying a contact point of platinum-iridium slides with a definite pressure on the chalk cylinder, so that a certain natural friction is set up between the cylinder and the contact point. The metal strip carrying the latter is connected to a diaphragm. If now a direct current flows between the cylinder and the metal point, the cylinder being connected to the positive pole of the source of supply, the natural friction is diminished as long as the current is in existence. It is therefore obvious that sound may be reproduced from the diaphragm if an alternating telephone current is superimposed on the direct current. In this case the action
719
will come into immediate proximity to the semi-conductor and will also be subjected to a large attractive force. The result is that the entire length of the strip will fold itself round the curved surface, as indicated by the dotted line, and its free end will thus be moved an appreciable distance. If a contact C is mounted as shown, it will be obvious that the arrangement forms an electrostatic relay,
Fio. 7. attraction can cause a motion and thus allow a certain small amount of mechanical work to be done. Fig. 6 shows a semi-conductor, H, with the metal coating, II. The semi-conductor has a cylindrically curved, smooth surface, in opposition to which a thin, elastic, smooth metal strip, I, is situated. If a certain potential difference is applied between I and II, a considerable attraction will be set up at the different points of the line along which the strip is touching the curved surface tangentially, and also at the points immediately above this line, where the air-gap is infinitesimal. This attraction will cause the strip to assume the curvature of the semi-conductor along this line, and in this way additional new points of the strip which the authors have developed for various purposes. On the other hand, the movement itself can be utilized for the detection of a potential difference between I and II, i.e. the arrangement can be used as an electroscope. As the attractive force is very strong in comparison with that obtained in a gold-leaf electroscope, the metal strip can be made sufficiently rigid to permit the apparatus to be used in all positions. The authors have accordingly constructed a pocket electroscope suitable for the indication of potentials from about 70 to 700 volts (d.c. or a.c). ,. In Fig. 7 this instrument is shown in section. It consists of a hard rubber holder carrying on its top the semi-conductor, H, and the strip, I, the thickness of
720
which is about 1/3 000 in. The metal coating, II, of the semi-conductor is connected with the metal point at the base of the instrument through a safetyresistance, R, of a few megohms, arranged in the interior of the holder. The strip is connected with a metal cap, C, which protects the upper parts of the instrument and which has a small observation window, W, at the .top. The end of the strip is bent at right angles and will only be visible behind the glass when the strip is attracted to the semi-conductor. The instrument, which in size and appearance greatly resembles a fountain pen, is especially useful for testing whether an electrical wire or any part of an electrical installation is alive. "Vtfh'en in use the instrument is held in the hand and its metal point is brought into contact with the object to be tested, the body of the user generally forming a sufficient earth connection, as the total resistance of the instrument exceeds 100 megohms. As a high resistance is desirable in this instrument; and its use is only occasional, no impregnation of the semi-conductor is necessary. Referring again to Fig. 4, three main types of apparatus with rotating semi-conduc.tor have been constructed for practical purposes by the authors. These types are : (1) A time-limit relay, (2) a telegraph recorder and relay, and (3) a loud-speaking telephone. Modifications of such apparatus may, of course, be used for special purposes, and the principle of electro-adhesion may obviously be utilized for many purposes for which electromagnetism is suitable. As previously mentioned, the electrostatic attraction will be sufficiently constant in the general arrangement illustrated in Fig. 4, if H is an agate cylinder filled with a suitable electrolyte. Experience shows that special precautions are also necessary to keep the coefficient of friction constant while the apparatus is in operation. This is due to several circumstances. If both I and H are brightly polished, and the apparatus is started without the application of a potential difference, the natural friction between cylinder and band will* gradually increase, due to the deposit of dust on the surfaces. The hard particles of the dust will act as ari abrasive and will thus wear more dust from the cylinder arid band. Even if the frictional system is protected from atmospheric dust, a certain natural wear takes place which is at the commencement very small,- but which increases rapidly when the least dust has been formed. Any dust or .powder originating .from the atmosphere or from wear will in the course of time; be ground to a very fine consistency and will, then1 adhere quite firmly to the agate, in the same way as fine chalk which is rubbed well into a. glass surface, causing at the. same time a considerable increase in the coefficient ;pf "friction. In this state the frictional system will produce a grinding or v squeaking sound and regular working will be impossible. The process ,is analogous to what takes place when a shaft .runs in a bearing which is hot lubricated. Lubrication used in connection with the electro-adhesion apparatus does not provide a remedy, as any lubricant, even if insulating, will almost entirely; spoil the electroadhesion, effect,, as it prevents .the;^intimate contact
721
cylinder is preferably driven by clockwork or by a very small low-tension motor with a worm gear as used in electric meters, and the speed chosen for certain purposes is about one revolution in 1 or 2 minutes. If the current is interrupted, the point, a, moves quickly back to its initial position. The potential necessary for actuating the relay is normally about 50 volts, although higher sensitivity can be obtained. The mechanical force available is ample for the operation of any ordinary contacts. If very heavy currents are to be dealt with, the contact device operated by the point, a, is replaced by a trigger device which is released by the point, a, and which in turn releases a heavy contact device or switch. The relay is more specially intended for the operation of bell alarms in radiotelegraphy and telephony, as well as in carrier-current telephony, and also in some special cases of remote control, If in any of these cases the incoming highfrequency energy is sufficient to actuate a sensitive high-frequency indicator (e.g. a sensitive hot-wire instrument), the latter can be fitted with a delicate contact arrangement and the time-limit relay be used as a secondary relay, which again can actuate a bell alarm or any special electric arrangement. The very small current actuating the time-limit relay (about 10 ~ 6 ampere) will not cause even very delicate contacts to stick, the relatively high potential (about 50 volts) ensuring reliable electrical contact even with very light contact pressure. In such cases the use of valves for alarms or any remote control may be dispensed with. If, in other cases, the relay is to be actuated directly by a valve current, the diagram of connections is the same as will be described under the heading " Telegraph Recorder aiid Relay." . It will be seen that a. continuous signal of. at least the length oi the time lag is necessary to operate the. relay,, as. any premature interruption of the signal will cause the relay to return quickly to its initial position without closing the contacts. A time-limit relay has also been constructed on the principle of two plane circular discs sliding on each other, one being stationary and connected with the relay contacts, and the other being rotated by clockwork. One disc may be semi-conductive and the other of metal, or both discs may, if desired, be of semiconductive material. The case of electro-adhesion between two semi-conductors has not been dealt with previously in the lecture; it presents no material difference from the case of electro-adhesion between a semi-conductor and a metallic body. The continual cleaning of the discs, however, presents such practical difficulties that the cylinder-and-band principle is preferable.
THE . TELEGRAPH. RECORDER AND RELAY.
If, again referring to Fig. 4, the point, a, is connected with relay contacts in such a way that contact is not made until the point, a, has moved a definite distance from its original position, a time lag is very simply introduced into the action of the relay, if the cylinder, H, revolves at a suitable (moderate), speed; If a. sufficiently high d.c. potential.is applied between 1 and 2, the band .will cling tightly to the; cylinder, and. the relative sliding .will cease instantaneously,, after which the point, a, will move steadily at the low peripheral speed of the cylinder until contact is made. The time lag can obviously be altered by adjusting either tide free path of the point,, a, or the speed of rotation. In the actual apparatus the
. A fairly wide field for the use of electro-adhesion is found in telegraphy. Apparatus for receiving (recording), relaying or transmitting purposes can be constructed, and the electro-adhesion principle can be combined with known systems of printing telegraphs, transmission of photographs, etc. Such apparatus can, however, be regarded as modifications or' applications
722
of the general arrangement of the telegraph recorder and relay shown diagrammatically in Fig. 8. Here H, I and II [Fig. 8 (a)] represent the friction system. The band I is fastened to a bell-crank lever, V, pivoted at the point, a. The light spring, f, holds the band taut. The horizontal arm of the lever is normally
Bl
V//////////////////'/'/'"""
FIG.
FIG.
9.
pressed against a fixed stop, s1( by means of the strong, apparatus. The reason for this relatively high capacity adjustable spring, F. The vertical arm carries the is, of course, the very small effective distance between siphon or other recording device. In Fig. 8 (b) the record- the two condenser charges. During the recording of ing arrangement, with siphon and paper drive is shown in the signals this condenser is continually charged and side elevation, together with a sample of the record. discharged, and the corresponding current must pass The operating potential difference is applied between the through the interior of- the semi-conductor. Conseleads 1 and 2 [Fig. 8 (a)] and causes the frictional quently, a very high internal resistance of the semipull in the band to overcome the pull of the spring, F,
+ 1OO
FIG.
8 (6).
FIG.
10.
so that the horizontal arm of the lever will ascend until it strikes an adjustable stop, s2, the position of which determines the amplitude of the recorded signs. Upon the cessation of the operating current, the strong spring, F, will quickly draw the lever back to the stop, s^ On the vertical arm of the lever is further shown a contact 3, which can touch in turn the contacts 4 and 5 and thus supply double current impulses from a local battery either to a local receiver working with double current, or to a cable or line, operating a distant
conductor will produce a certain lag in the charge and discharge of the electro-adhesion system and therefore also in the action of the apparatus, thus limiting the maximum recording speed attainable. The low internal resistance necessary for high-speed recording is, however, obtained by the chemical impregnation of the agate, and it was in fact only the introduction by the authors (in 1919) of the hollow agate cylinder containing electrolyte which made high-speed recording by electro-adhesion possible over any extended period.
723
the charge on the friction system in this case must pass through the large contact resistance of the system, whereas the charge has only to pass through the much smaller internal resistance of the semi-conductor if the discharge can take place through an external circuit. The latter is always the case if the apparatus is constantly shunted with a suitable external resistance, and thus the apparatus can, without any difficulties of the kind just mentioned, be operated in connection with a valve with an anode resistance, as illustrated in Fig. 10.
20
35
50
U
ft
II
M
CO
65
100
.a
d < D
is
II II
150
200
11. In this figure R is the anode resistance of the valve the high-tension supply to which can be regulated by means of the potentiometer, Sd. Tig is the telegraph recorder. The telegraph impulses are applied to the terminals X and Y, which are connected with the grid and the filament respectively of the valve. The small battery, b, ensures that the grid is normally kept at a suitable negative potential relative to the filament terminal Y, X and Y being supposed connected. Normally, therefore, the anode current and consequently the drop of potential across R is very small, thus pro-
station one terminal of trie apparatus is connected to the line and the other to earth. The earthing of the line at the transmitting station is very essential. If the line were simply disconnected from the battery during the pauses between the signals, the charge accumulated on the line would have to be discharged through the very high resistance of the apparatus, and this would require a considerable time. Even if the line has a negligible length and capacity, a considerable lag in the discharge of the friction system proper will be experienced if the line is completely interrupted, as
724
ducing a negligible electro-adhesion in the telegraph receiver. If telegraph impulses of sufficient strength are applied between X and Y in such a way that the grid is made more positive during the signals, the drop of potential across R will increase sufficiently to operate the apparatus. This will also be the case if a sufficiently strong alternating E.M.F. is applied between X and Y, the valve acting as a rectifier. Fig. 10 therefore represents the general diagram of connections for" valve reception. If the valve is acting as a rectifier, the condenser, C, may be added in order to smooth out the fluctuations of the potential across R due to the alternating current, though the capacity of the electro-adhesion system proper is in many cases sufficient for this purpose. A very perfect rectification is by no means necessary for satisfactory reception, and a large capacity, C, will, on the other hand, reduce the maximum speed of reception, as will be readily understood: The electro-adhesion telegraph is used with advantage for telegraphic reception at high speeds, and, on account of its small current consumption, in connection with high-resistance circuits (valve circuits included). . In Fig. 11 are shown samples of records obtained in a laboratory test direct from a transmitter, giving the standard word " Paris " at various speeds. The speed of the movement of the paper was varied somewhat for each sample, and therefore the "space occupied by each symbol does not correspond to the speed (indicated on the scale in words per minute). The test was made with one of our early models having & comparatively heavy recording system (9 grammes), so 'that much betterrecords can actually be obtained at the higher speeds. Even at the very high speed of 300 "words per minute, however, the record is, as will be seen, quite satisfactory. The record at the extremely high speed of 600 words per minute was taken with the' same apparatus;' land can, in fact, be easily reads At present, however; such a high speed is of no value in practical telegraphy, though the extremely quick action of the apparatus may be found to be useful for some systems of telegraphic transmission of photographs. . . . - .. If the electro-adhesion telegraph is connected "with a small valve as generally used for radio reception, in the manner shown in Fig; 10> a recording speed of 300 words per minute is easily obtained without using a number of valves in parallel (or a very large valve) for the operation.* If radio signals are to be recorded, a sufficient amplification is necessary and in this case any ordinary amplifier may be inserted between the radio receiver and the terminals X and Y.
Demonstration.The early telegraph model was shown in operation after the lecture, recording radio signals received on a temporary radio installation erected at the Institution building with the kind assistance of the Marconi Company.
T H E LOUD-SPEAKING TELEPHONE.
B
|I|I|I|II
FIG.
12.
plays the same role as the permanent magnetism in electromagnetic telephones. The use of a suitable polarization' E.M.F.; moreover, causes the apparatus to work on the steep part of the characteristic curve of the electro-adhesion system (cf. Fig. 5), where small variations of E.M.F. correspond to large variations of force, and where the curve can, within the limits of the force variation taking place
H+h-
FIG.
13.
In Fig. 12, H, I and II is the electro-adhesion system, and f the spring holding the band, I, taut. The band is mechanically connected with the diaphragm of a soundbox L, either directly, as shown in the figure, or by
* The ordinary anode resistance of about 100 000 ohms is amply sufficient for the discharge of the electro-adhesion system at this speed.
during speech reproduction, be replaced approximately by a straight line, so that only negligible speech distortion occurs due to this cause.* It is obvious' that the highest alternating E.M.F.'s occurring must be considerably smaller than the polarization E.M.F. If the loud speaker is to be operated in connection with a thermionic tube, as for instance for the reproduction of radio-telephony, the circuit shown in Fig. 13 can be used with advantage.
* The actual forces in the normal loud speaker with about 70 volts polarization E.M.F. are smaller than. Fig. 5 seems to indicate, as a smaller band, encircling less than half of the cylinder circumference, is used for the loud speaker.
725
heavy diaphragms, which will give very good reproduction without the use of a horn, which always produces some resonance effects.
Demonstration.At the lecture a demonstration was given of a " speaking violin." An electro-adhesion telephone, in which the band was attached to the resonant body of a violin, the strings of which had been removed, reproduced violin music and speech transmitted from a microphone in a distant part of the building. As is well known, the violin body will resonate fairly equally over a very extended range of notes, including very high notes, and therefore music and speech are very well reproduced, the speech in particular being very clear and well articulated. As, however, the violin body adds harmonics to every simple oscillation imparted to it, the reproduction in each case exhibits some special " violin character." The timbre of the speech is therefore not reproduced quite faithfully, the reproduction of violin music being, on the other hand, of exceptional beauty, as the " violin character" is imparted once more to the music performed before the microphone.
The electro-adhesion telephone is capable of producing sound of great intensity without requiring the use of special power microphones or power valves ; at the same time, the faithfulness of the reproduction is not surpassed by any loud-speaking apparatus hitherto existing. The authors have constructed a specially powerful model, in which the friction system actuates simultaneously a number of diaphragms ; this model gives very good reproduction even at very high sound intensities at which electromagnetic telephones would be heavily overloaded and therefore exhibit considerable distortion. The authors wish to express their indebtedness to the Technical College (Polyteknisk Laereanstalt), Copenhagen, and especially to the Principal of the Electrotechnical Laboratory, Professor Absalon Larsen, for the great kindness shown them during their many years' experimental work in the Laboratories of the College.