Scribd Logo
Upload

Welcome to Scribd!

  • 83 views

    NPort 5100 Series QIG v3

    Uploaded by

    raul_blazquez_iturbide
    The document provides instructions for setting the pull high/low resistor values on an NPort 5100 Series device. The default resistor value is 150 KΩ, but it can be changed to 1 KΩ by shorting jumpers. The 1 KΩ setting should not be used for RS-232 mode. The document also includes an overview of the NPort 5100 Series, which allows control of serial devices over Ethernet, and provides instructions for hardware installation, software installation, pin assignments, and specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    NPort 5100 Series QIG v3

    Uploaded by

    raul_blazquez_iturbide
    83 views2 pages
    The document provides instructions for setting the pull high/low resistor values on an NPort 5100 Series device. The default resistor value is 150 KΩ, but it can be changed to 1 KΩ by shorting jumpers. The 1 KΩ setting should not be used for RS-232 mode. The document also includes an overview of the NPort 5100 Series, which allows control of serial devices over Ethernet, and provides instructions for hardware installation, software installation, pin assignments, and specifications.

    Original Title

    NPort_5100_Series_QIG_v3

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for setting the pull high/low resistor values on an NPort 5100 Series device. The default resistor value is 150 KΩ, but it can be changed to 1 KΩ by shorting jumpers. The 1 KΩ setting should not be used for RS-232 mode. The document also includes an overview of the NPort 5100 Series, which allows control of serial devices over Ethernet, and provides instructions for hardware installation, software installation, pin assignments, and specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    83 views2 pages

    NPort 5100 Series QIG v3

    Uploaded by

    raul_blazquez_iturbide
    The document provides instructions for setting the pull high/low resistor values on an NPort 5100 Series device. The default resistor value is 150 KΩ, but it can be changed to 1 KΩ by shorting jumpers. The 1 KΩ setting should not be used for RS-232 mode. The document also includes an overview of the NPort 5100 Series, which allows control of serial devices over Ethernet, and provides instructions for hardware installation, software installation, pin assignments, and specifications.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Adjustable pull high/low resistor for RS-422/485

    NPort 5100 Series Quick Installation Guide


    Third Edition, January 2011

    (150 K or 1 K)
    Jumpers are used to set the pull high/low resistor values. The default is 150 K. Short the jumpers to set this value to 1 K. Do not use the K setting with RS-232 mode, since doing so will degrade the RS-232 signals and shorten the communication distance.

    1. Overview
    NPort 5100 series device servers are compact, palm-sized data communication devices that allow you to control RS-232 (NPort 5110), RS-422/485 (NPort 5130), and RS-232/422/485 (NPort 5150) serial devices over a TCP/IP-based Ethernet. Note: -T indicates an extended temperature model.

    2. Package Checklist
    Before installing the NPort 5100 series device server, verify that the package contains the following items: 1 NPort 5100 series 1-port serial device server 4 stick-on pads Documentation and software CD Quick Installation Guide Warranty card

    4. Hardware Installation Information


    NOTE The NPort 5110, NPort 5130, and NPort 5150 have the same form factor. Reset ButtonPress the Reset button continuously for 5 sec to load factory defaults: Use a pointed object, such as a straightened paper clip or toothpick, to press the reset button. This will cause the Ready LED to blink on and off. The factory defaults will be loaded once the Ready LED stops blinking (after about 5 seconds). At this point, you should release the reset button. LED IndicatorsNPort 5100s top panel has three LED indicators, which are described in the following table. LED Name LED Color Ready Red LED Function Steady on: Power is on and NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server is not responding properly. Steady on: Power is on and NPort is functioning normally. Blinking: The NPort has been located by NPort Administrators Location function Power is off, or power error condition exists. 10 Mbps Ethernet connection. 100 Mbps Ethernet connection. Ethernet cable is disconnected, or has a short. Serial port is receiving data. Serial port is transmitting data. No data is being transmitted or received through the serial port. STEP 1: After removing the NPort 5100 series device server from the box, the first thing you should do is connect the power adaptor. STEP 2: Connect the NPort 5100 series device server to a network. Use a standard straight-through Ethernet cable to connect to a hub or switch. When setting up or testing the NPort 5100 series device server, you might find it convenient to connect directly to your computers Ethernet port. In this case, use a cross-over Ethernet cable. STEP 3: Connect the NPort 5100 series device servers serial port to a serial device. STEP 4: Placement options In addition to placing the NPort 5100 on a desktop or other horizontal surface, you may also make use of the DIN-Rail or Wall Mount options, as illustrated here. Wall Mount DIN-Rail

    Optional Accessory

    Notify your sales representative if any of the above items are missing or damaged.

    DK-35A: DIN-Rail Mounting Kit (35 mm)

    3. Hardware Introduction
    As shown in the following figures, NPort 5100 series device servers have one male DB9 port for transmitting RS-232 (NPort 5110), RS-422/485 (NPort 5130), or RS-232/422/485 (NPort 5150) serial data.

    Green

    Off Link Orange Green Off Tx/Rx Orange Green Off P/N: 1802054000312 1

    5. Software Installation Information


    To install NPort Administration Suite, insert the NPort Document & Software CD into your computers CD-ROM drive. Once the NPort Installation CD window opens, click on the Installation button, and then follow the instructions on the screen.

    To view detailed information about NPort Administration Suite, click on the Documents button, and then select NPort 5100 Series Users Guide to open the pdf version of the users guide.

    NPort 5150DB9 male (RS-232/422/485) port pinouts

    6. Pin Assignments
    Ethernet Port Pinouts Pin Number 1 2 3 4 5 6 7 8 9 RS-232 DCD RxD TxD DTR GND DSR RTS CTS --RS-422/485 (4W) TXD-(A) TXD+(B) RXD+(B) RXD-(A) GND --------RS-485 (2W) ----Data+(B) Data-(A) GND ---------

    Pin Number 1 2 3 6

    Ethernet Tx+ TxRx+ Rx-

    NPort 5110DB9 male (RS-232) port pinouts

    7. Specifications
    Power Requirements Power Input 12 to 48 VDC Power Consumption NPort 5110: 128.7 mA@12V, 72 mA@24V NPort 5130: 200 mA@12V, 106 mA@24V NPort 5150: 200 mA@12V, 106 mA@24V Operating 0 to 55C (32 to 131F), for standard Temperature models -40 to 75C (-40 to 167F), for -T models Operating Humidity 5 to 95% RH Dimensions 75.2 80 22 mm including (2.96 3.15 0.87 in) ears 52 80 22 mm (2.05 3.15 0.89 in) Serial Line Protection Magnetic Isolation Power Line Protection Regulatory Approvals Pin Number RS-422/485 (4W) 1 TXD-(A) 2 TXD+(B) 3 RXD+(B) 4 RXD-(A) 5 GND 6 --7 --8 --9 --RS-485 (2W) ----Data+(B) Data-(A) GND --------without ears

    Pin Number 1 2 3 4 5 6 7 8 9

    RS-232 DCD RxD TxD DTR GND DSR RTS CTS ---

    NPort 5130DB9 male (RS-422/485) port pinouts

    15 KV ESD for serial port 1.5 KV for Ethernet Level 2 Burst (EFT), EN61000-4-4 Level 2 Surge, EN61000-4-5 FCC Class A, CE Class A, UL, LVD

    www.moxa.com/support The Americas: Europe: Asia-Pacific: China: +1-714-528-6777 (toll-free: 1-888-669-2872) +49-89-3 70 03 99-0 +886-2-8919-1230 +86-21-5258-9955 (toll-free: 800-820-5036)

    2011 Moxa Inc., All Rights Reserved

    You might also like