Scribd
Upload
142 views

Simatic Hmi Wincc V7.0 Sp1 File Server

Notices referring to your personal safety are highlighted in the manual by a safety alert symbol. A notice warning of property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used.

Uploaded by

Amajd
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
142 views

Simatic Hmi Wincc V7.0 Sp1 File Server

Notices referring to your personal safety are highlighted in the manual by a safety alert symbol. A notice warning of property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used.

Uploaded by

Amajd
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

SIMATIC HMI WinCC V7.

0 File Server

1 Setting Up the File Server ______________

SIMATIC HMI WinCC V7.0 SP1 File Server

Printout of the Online Help

11/2008

Safety Guidelines

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage
Note the following: WARNING This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance.

Trademarks
All names identified by are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG Automation and Drives Postfach 48 48 90327 NRNBERG GERMANY

Printout of the Online Help 11/2008

Copyright Siemens AG 2008. Technical data subject to change

Table of contents
1 Setting Up the File Server.......................................................................................................................... 5 Index.......................................................................................................................................................... 7

File Server 11/2008, Printout of the Online Help

Table of contents

File Server 11/2008, Printout of the Online Help

Setting Up the File Server


Introduction
The WinCC file server is a server with minimum configuration of WinCC components. You can save projects on the file server and manage them centrally. For example, this facilitates the creation of periodic backup copies of all projects. Note You use the file server exclusively for configuring.

Requirement
Before installing a WinCC Fileserver V7, please observe the conditions described in the Installation Notes. In addition, the computer must be available on the network (LAN). Note WinCC V7 and WinCC Fileserver V7 cannot be installed at the same time on one computer.

Installation
In order to set up a computer as a file server, you run the Fileserver Setup on the computer. On the WinCC installation DVD in the "Programs" dialog in the "WinCC" group select the "WinCC V7.0 Fileserver" option. The minimum installation for WinCC is installed on the computer.

Configuration
The projects are stored on the file server. To enable all project members to access the projects, you must share the corresponding drives or folders on the file server. Note You must have administrator rights to share folders or drives. Assign the shared folders or drives with unique drive letters on the configuration computers. Project members can then open the projects on the file server like a local project.

File Server 11/2008, Printout of the Online Help

Setting Up the File Server

File Server 11/2008, Printout of the Online Help

Index
C
Configuration, 5 File server, 5

F
File server, 5 Configuration, 5 Installation, 5

I
Installation, 5 File server, 5

File Server 11/2008, Printout of the Online Help

You might also like