1. Refer to the exhibit. What information can be determined from the displayed output?

EIGRP packets are waiting to be sent to the neighbors. The adjacencies between the routers are yet to be established. The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2. Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface. 2. Which two router component and operation pair are correctly described? (Choose two.) DRAM loads the bootstrap RAM stores the operating system Flash executes diagnostics at bootup NVRAM stores the configuration file ROM stores the backup configuration file POST runs diagnostics on hardware modules 3. Which statement correctly describes a feature of RIP? RIP is a link-state routing protocol. RIP uses only one metrichop count for path selection. Advertised routes with hop counts greater than 10 are unreachable. Messages are broadcast every 10 seconds.

4. Refer to the exhibit. RouterA and RouterB cannot successfully exchange EIGRP routes. What is the problem? The hello intervals do not match. The autonomous system numbers do not match. The no auto-summary command is missing from both routers. The ip bandwidth-percent command is missing from RouterB.

5. Refer to the exhibit. Which option will provide the configuration that is needed for router R1 to dynamically learn routes to the 192.168.100.16/28, 192.168.100.32/28, and 192.168.100.48/28 subnetworks? with static routes with a routed protocol with a routing protocol with directly connected routes

6. Refer to the exhibit. The network administrator has run the following command on R1. R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2 What is the result of running this command? Traffic for network 192.168.2.0 is forwarded to 172.16.1.2. This route is automatically propagated throughout the entire network. Traffic for all networks is forwarded to 172.16.1.2. The command invokes a dynamic routing protocol for 192.168.2.0. 7. A network administrator is using an application that is monitoring packets on the network and sees an EIGRP update packet. What is the purpose of the update packet? The packet is sent to discover neighbors within the EIGRP network. The packet is sent to search for network devices within an EIGRP network. The packet is used to propagate routing information within the EIGRP network. The packet is used to send an unreachable reply to another router within the EIGRP network. The packet is used to notify all routers that EIRGP has failed on one of the routers within the EIGRP network. 8. Which two statements are true about the router ID in a single area OSPF network? (Choose two.) Only the DR and BDR have a router ID. A loopback interface is required to configure the router ID. The router ID is used to uniquely identify each router in the OSPF routing domain. Any interface, even one not participating in the OSPF routing process, can be used to determine the router ID. If no loopback interfaces are configured, the router chooses the highest active IP address of any of its physical interfaces.

9.

Refer to the exhibit. A network administrator has configured OSPF using the following command: network 192.168.1.32 0.0.0.31 area 0 Which router interface will participate in OSPF? FastEthernet0/0 FastEthernet0/1 Serial0/0/0 Serial0/0/1 10. Which two statements are true for link-state routing protocols? (Choose two.) Routers that run a link-state protocol can establish a complete topology of the network. Routers in a multipoint network that run a link-state protocol can exchange routing tables. Routers use only hop count for routing decisions. The shortest path first algorithm is used. Split horizon is used to avoid routing loops. 11. What is the function of the OSPF LSU packet? used to confirm receipt of certain types of OSPF packets used to establish and maintain adjacency with other OSPF routers used to request more information about any entry in the BDR used to announce new OSPF information and to reply to certain types of requests 12. Which two statements about routing protocols are accurate? (Choose two.) OSPF supports VLSM. RIPv1 supports VLSM. RIPv2 does not have a hop count limit. EIGRP supports discontiguous network designs. RIPv2 does not support discontiguous network designs.

13. Refer to the exhibit. Router R2 is configured properly and all interfaces are functional. Router R1 has been installed recently. Host A is unable to ping host B. Which procedure can resolve this problem? Configure a static route on R1 using the IP address of the serial interface on R1. Configure a default route on R1 with the exit interface Fa0/0 on R1. Configure a static route on R1 using the IP address of S0/0/0 on R2. Configure a default route on R1 using the IP address of Fa0/0 on R2.

14. Refer to the exhibit. The interfaces of all routers are configured for OSPF area 0. R3 can ping R1, but the two routers are unable to establish a neighbor adjacency. What should the network administrator do to troubleshoot this problem? Check if the interfaces of the routers are enabled. Check the hello and dead intervals between the routers. Check the process ID of both routers. Check if CDP is enabled on all the routers. 15. A network administrator is setting up a new router with a device name of Admin, an encrypted password of cangetin, and the IP address 192.168.1.22/29 assigned to the first FastEthernet interface. Which command sequence correctly configures this router? Router(config)# hostname Admin Admin(config)# enable secret cangetin Admin(config)# interface fa0/1 Admin(config-if)#ip address 192.168.1.22 255.255.255.248 Router(config)# hostname Admin Admin(config)# enable password cangetin Admin(config)# interface fa0/1 Admin(config-if)# ip address 192.168.1.22 255.255.255.248 Router(config)# hostname Admin Admin(config)# enable secret cangetin Admin(config)# interface fa0/0 Admin(config-if)# ip address 192.168.1.22 255.255.255.248 Router(config)# hostname Admin Admin(config)# enable password cangetin Admin(config)# interface fa0/0 Admin(config-if)# ip address 192.168.1.22 255.255.255.248 16. Which routing protocol maintains a topology table separate from the routing table? IGRP RIPv1 RIPv2 EIGRP

17.

Refer to the exhibit. The hosts on the R1 LAN are unable to access the Internet. What is incorrectly configured? the IP address of the Fa0/0 interface at R1 the IP address of the S0/0/1 interface at R2 the IP address of the S0/0/0 interface at R1 the subnet mask of the S0/0/1 interface at R2 18. All routers in a network are configured in a single OSPF area with the same priority value. No loopback interface has been set on any of the routers. Which secondary value will the routers use to determine the router ID? The highest MAC address among the active interfaces of the network will be used. There will be no router ID until a loopback interface is configured. The highest IP address among the active FastEthernet interfaces that are running OSPF will be used. The highest IP address among the active interfaces will be used.

19. Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2? 192.168.1.0/24 192.168.0.0/24 192.168.0.0/22 192.168.1.0/22 20. Which protocol is used by EIGRP to deliver and receive update packets? FTP RTP TCP TFTP UDP 21. A router boots and enters setup mode. What is the reason for this? The IOS image is corrupt. Cisco IOS is missing from flash memory. The configuration file is missing from NVRAM. The POST process has detected hardware failure. 22. What is the purpose of the TTL field within an IP packet header? clears an unreachable route from the routing table after the invalid timer expires prevents regular update messages from inappropriately reinstating a route that may have gone bad removes an unreachable route from the routing table after the flush timer expires limits the period of time or number of hops a packet can traverse through the network before it should be discarded used to mark the route as unreachable in a routing update that is sent to other routers

23. Refer to the exhibit. If the EIGRP routing protocol is used throughout the network, which IP address and mask prefix should be sent by router R1 to the Edge router as a result of manual summarization of LANs A, B, C, and D? 192.168.4.0/20 192.168.4.0/22 192.168.4.0/24 192.168.4.0/26 24. A technician needs to determine the value of the router ID for a branch router. What three commands can be used from the branch router to determine the router ID for a particular router that is participating in OSPF routing? (Choose three.) show ip ospf show ip route show ip protocols show ip ospf interface show ip ospf neighbor show ip interface brief

25.

Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configured and operational. Both routers are configured to include all connected interfaces in routing updates. R2 is not showing any routes from R1 in the routing table. What is the likely cause? The adjacent interfaces are passive. The distance of 120 exceeds 15 hops. R2 will not accept version 1 updates from R1. Routes are being summarized by R1 but not by R2. 26. Which multicast address does EIGRP use to send hello and updates packets? 224.0.0.5 224.0.0.6 224.0.0.9 224.0.0.10 27. Which default EIGRP configuration must be modified to allow an EIGRP router to advertise subnets that are configured with VLSM? split horizon metric K values autosummarization hello and dead intervals 28. Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a router? (Choose three.) The router modifies the TTL field, decrementing it by one. The router changes the source IP to the IP of the exit interface. The router maintains the same source and destination IP. The router changes the source physical address to the physical address of the exit interface. The router changes the destination IP to the IP of the exit interface. The router sends the packet out all other interfaces, besides the one it entered the router on.

29. Refer to the exhibit. A technician has configured the interfaces on the Router, but upon inspection discovers that interface FastEthernet0/1 is not functioning. Which action will most likely correct the problem with FastEthernet0/1? A clock rate should be added to the interface configuration. The subnet mask should be added to the interface configuration. An interface description needs to be added to the interface configuration. The no shutdown command needs to be added to the interface configuration.

30.

Refer to the exhibit. Routers R1 and R2 are directly connected through a FastEthernet link but cannot form a neighbor adjacency. What could resolve the problem? The cost on R1 should be set higher. The priority on R1 should be set higher. The OSPF process ID numbers must match. A backup designated router needs to be added to the network. The hello and dead timers must be configured with the same values on both routers. 31. Which prompt is used to allow a user to change the IP address of an interface on a router? Router> Router# Router(config)# Router(config-if)#

32. Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration as router RTR_A. What should be done so that host A can access server A? Add the command no auto-summary on all routers. Change the network statements to include a wildcard mask. Adjust the EIGRP hello timers to account for the network delay. Add the command eigrp log-neighbor-changes on all routers. 33.

Refer to the exhibit. All routers are configured to use the EIGRP routing protocol with default settings, all routes are advertised on all routers, and the network is fully converged. Which path will the data take to travel between 172.16.1.0/24 and 192.168.100.0/24? It will travel via A, B, and C.

It will travel via A, F, E, D, and C. It will travel via A, G, H, and C. The traffic will be load-balanced on all paths. 34. Which of the following are primary functions of a router? (Choose two.) packet switching microsegmentation domain name resolution path selection flow control 35. In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths? R 192.168.1.0/24 [120/3] via 192.168.110.1, 00:00:17, Serial0/1/0 R 192.168.1.0/24 [120/2] via 192.168.200.1, 00:00:17, Serial0/0/0 R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial0/0/1 R 192.168.1.0/24 [120/4] via 192.168.101.1, 00:00:17, Serial0/1/1

36. Refer to the exhibit. Router R1 receives a packet with a destination of 172.19.130.1. To which network in the routing table will the packet be matched? 172.20.0.0/16 172.20.0.0/17 172.20.0.0/24 172.18.0.0/15 0.0.0.0/0 37.

Refer to the exhibit. Which path will traffic from the 172.16.1.0/24 network take to get to the 10.0.0.0/24 network?

ADC ABC It will load balance the traffic between ADC and ABC It will send the traffic via ABC, and will use ADC as a backup path only when ABC fails.

38. Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this? The IP address of host A is incorrect. The default gateway of host A is incorrect. The Fa0/1 interfaces of the two routers are configured for different subnets. The subnet mask for the Fa0/0 interface of R1 is incorrect.

39. Refer to the exhibit. R1 and R2 are both configured with RIPv1. Beginning from global configuration mode, what comand or commands will eliminate RIP updates on the Ethernet segment of R2? a) R2# configure terminal R2(config)# router rip R2(config-router)# passive-interface FastEthernet0/0 b) R2# configure terminal R2(config)# passive-interface FastEthernet0/0 c) R2# passive-interface FastEthernet0/0 d) R2# configure terminal R2(config)# interface FastEthernet0/0 R2(config-if)# passive-interface FastEthernet0/0 40. What is a characteristic of classful routing? support for VLSM the use of 48-bit addresses routing updates do not include a subnet mask addresses that are typically entered in hexadecimal format 41.

Refer to the exhibit. The 10.4.0.0 network fails. What mechanism prevents R2 from receiving false update information regarding the 10.4.0.0 network?

split horizon hold-down timers route poisoning triggered updates

42. Refer to the exhibit. Which IP address and subnet mask can be configured on host H1 if it is to communicate with the network? 172.16.1.0 255.255.255.248 172.16.1.14 255.255.255.240 172.16.1.17 255.255.255.240 172.16.2.1 255.255.240.0 172.16.2.2 255.255.255.0 43.

Refer to the exhibit. What will happen when the router reloads? It will boot into ROMMON mode. It will ignore the start-up configuration file. It will look for the start-up configuration file on the TFTP server. It will attempt to load the start-up configuration file that is stored in NVRAM. 44. A router has learned about a network through static and dynamic routing processes. Which route will be used to reach network 192.168.168.0?

D 192.168.168.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Ethernet0 O 192.168.168.0/24 [110/1012] via 192.168.200.1, 00:00:22, Ethernet0 R 192.168.168.0/24 [120/1] via 192.168.200.1, 00:00:17, Ethernet0 S 192.168.168.0/24 [1/0] via 192.168.200.1 45.

Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.) A static route will be updated in the routing table. The traffic from the Internet will be directed to R2. The traffic from the source network 172.16.0.0/22 will be blocked. The route will be specified as the default route for all networks not defined in the routing table. All the broadcasts will be forwarded via the S0/0/0 interface of R2. 46.

Refer to the exhibit. What does the state FULL/ - indicate? The DR/BDR election is currently taking place. The router with router ID 10.112.0.34 and RouterA are on a point-to-point network. RouterA could not form a neighbor relationship with the router with router ID 10.112.0.34. OSPF hello and dead timers between RouterA and the router with router ID 10.112.0.34 do not match. 47. You have been asked to explain converged networks to a trainee. How would you accurately describe a converged network? A network is converged when all routers have formed an adjacency. A network is converged immediately after a topology change has occurred. A network is converged when all routers flush the unreachable networks from their routing tables. A network is converged after all routers share the same information, calculate best paths, and update their routing tables.

48. Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password? The login command was not entered on the console line. The enable password should be an enable secret password. No username and password combination has been configured. Console connections cannot be configured to require users to provide passwords.

49. Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be listed in the R2 routing table? a) C 172.16.0.0 is directly connected, Serial0/0/0 C 192.168.2.0 is directly connected, Serial0/0/1 S* 0.0.0.0 is directly connected, Serial0/0/0 b) S 172.16.1.0 [1/0] via 172.16.2.1 C 172.16.2.0 is directly connected, Serial0/0/0 C 192.168.2.0 is directly connected, Serial0/0/1 c) S 172.16.1.0 [1/0] via 172.16.2.1 C 172.16.2.0 is directly connected, Serial0/0/0 C 192.168.2.0 is directly connected, Serial0/0/1 S* 0.0.0.0 is directly connected, Serial0/0/1 d) S 172.16.1.0 is directly connected, Serial0/0/0 C 172.16.2.0 is directly connected, Serial0/0/0 C 192.168.2.0 is directly connected, Serial0/0/1 S* 0.0.0.0 is directly connected, Serial0/0/1 50. Which of the following are required when adding a network to the OSPF routing process configuration? (Choose three.) network address loopback address autonomous system number subnet mask wildcard mask

area ID

51. Refer to the exhibit. The network consists of hundreds of routers branched from connected regional distribution sites using single area OSPF. Recent network failures caused packet flooding and route recalculations in all branch networks. What should the engineer do to minimize the effect of the routing instabilities? Adopt RIPv2 which is not subject to packet flooding. Implement static routing. Implement a mix of routing protocols to contain the instabilities. Change the topology to a heirarchical design which puts each branch network in its own area.

52. Refer to the exhibit. A ping from R1 to 10.1.1.2 is successful, but a ping from R1 to 192.168.2.0 fails. What is the cause of this problem? There is no gateway of last resort at R1. The serial interface between the two routers is down. A default route is not configured on R1. The static route for 192.168.2.0 is incorrectly configured. 53. When would the IOS image held in ROM be used to boot the router? during a file transfer operation during a normal boot process when the full IOS cannot be found when the running configuration directs the router to do this 54. A router needs an IOS upgrade. Which component must be checked to make sure it meets the requirement for the new IOS? boot ROM Fast Ethernet ports flash serial ports UART CPU

55. Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.) The missing information for Blank 1 is the command show ip route. The missing information for Blank 1 is the command debug ip route. The missing information for Blank 2 is the number 100. The missing information for Blank 2 is the number 120. The missing information for Blank 3 is the letter R. The missing information for Blank 3 is the letter C.

56. Refer to the exhibit. Packets destined to which two networks will require the router to perform a recursive lookup? (Choose two.) 10.0.0.0/8 64.100.0.0/16 128.107.0.0/16 172.16.40.0/24 192.168.1.0/24 192.168.2.0/24 57. When would the network administrator use the ip bandwidth-percent eigrp as-number percent command? when there is a low bandwidth connection when the connection is on a shared medium when the connection is serial instead of Ethernet when the link is always busy

58. Refer to the exhibit. Cost for each path are shown. If all routers are configured to use OSPF, what would be the path of a packet sent from Router C to Router D if Router A was down? C-B-E-D C-B-A-D C-F-E-D C-F-B-A-D C-F-E-A-D 59. What OSPF packet type is used to elect the designated router (DR) and backup designated router (BDR) on multiaccess networks? hello LSU LSR DBD LSAck 60.

Refer to the exhibit. What are two of the routes added to the routing table of R1? (Choose two.) R 172.16.1.0/24 [120/1] via 192.168.3.0, 00:00:24, Serial0/0/0 R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1 R 192.168.9.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0 R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0 R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0 61.

Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route? Compared to RIP, EIGRP has a lower administrative distance. Compared to EIGRP, RIP has a higher metric value for the route. Compared to RIP, the EIGRP route has fewer hops. Compared to RIP, EIGRP has a faster update timer.

62. Refer to the exhibit. Routers R1 and R2 are directly connected via their serial interfaces and are both running the EIGRP routing protocol. R1 and R2 can ping the directly connected serial interface of their neighbor, but they cannot form an EIGRP neighbor adjacency. What action should be taken to solve this problem? Enable the serial interfaces of both routers. Configure EIGRP to send periodic updates. Configure the same hello interval between the routers. Configure both routers with the same EIGRP process ID.

63.

Refer to the exhibit. The hosts that are connected to R2 are unable to ping the hosts that are connected to R1. How can this problem be resolved? Configure the router ID on both routers. Configure the R2 router interfaces for area 0. Configure a loopback interface on both routers. Configure the proper subnet masks on the router interfaces. 64.

Refer to the exhibit. All routers are properly configured with default configurations and are running the OSPF routing protocol. The network is fully converged. A host on the 192.168.3.0/24 network is communicating with a host on the 192.168.2.0/24 network.Which path will be used to transmit the data? The data will be transmitted via R3-R2. The data will be transmitted via R3-R1-R2. The traffic will be load-balanced between two paths one via R3-R2, and the other via R3-R1R2. The data will be transmitted via R3-R2, and the other path via R3-R1-R2 will be retained as the backup path. 65.

Refer to the exhibit. What is the meaning of the highlighted value 120? It is the metric that is calculated by the routing protocol. It is the value that is used by the DUAL algorithm to determine the bandwidth for the link. It is the administrative distance of the routing protocol. It is the hold-down time, measured in seconds, before the next update. 66.

Refer to the exhibit. PC1 is unable to access the Internet. What is the cause of the problem? An incorrect IP address is configured between the two routers. No static route is configured on Router2. A routing loop has occurred. No routing protocol is configured on either of the two routers. 67. How does route poisoning prevent routing loops? New routing updates are ignored until the network has converged. Failed routes are advertised with a metric of infinity. A route is marked as unavailable when its Time to Live is exceeded. The unreachable route is cleared from the routing table after the invalid timer expires. 68. Which statement is true about the metrics used by routing protocols? A metric is a value used by a particular routing protocol to compare paths to remote networks. A common metric is used by all routing protocols. The metric with the highest value is installed in the routing table. The router may use only one parameter at a time to calculate the metric. 69.

Refer to the exhibit. OSPF is used for the routing protocol and all interfaces are configured with the correct IP addresses and subnet masks. During testing, it is found that router R1 is unable to form an adjacency with R2. What is the cause of this problem? Both routers have been configured with incorrect router IDs. Both routers have been configured in different OSPF areas. Both routers have been configured with an incorrect network type. Both routers have been configured with different hello and dead intervals. 70. A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared? hub router access point Ethernet switch 71. Which network and mask combination requires the use of a classless addressing solution? 10.32.0.0/11 172.16.0.0/12 192.168.0.0/24 192.168.128.32/27 72. A company is using static routes that are configured with an administrative distance of 1 on all routers in the network. The network administrator decides to introduce a dynamic routing protocol to reduce the manual configurations for the static routes. Which option identifies the correct procedure for the dynamic routing to take place in the network? The static routes and the dynamic routes will have the traffic alternate between them. The static routes will be automatically removed once the dynamic routing is configured. The static routes will be automatically updated with the next hop IP address once the dynamic routing is configured. The static routes must be manually removed from all routers in order for the dynamic routes to be installed in the routing table.

73. Refer to the exhibit. When a static IP address is being configured on the host, what address should be used for the default gateway? 10.1.1.1 10.1.1.2 172.16.1.1 192.168.1.1

74. Refer to the exhibit. The entire 192.168.1.0 network has been allocated to address hosts in the diagram. Utilizing VLSM with contiguous address blocks, which set of addresses and prefixes could be used to create an addressing solution with a minimum waste of IP addresses? Correct answer is image 4.

75.

Refer to the exhibit. The network is configured for OSPF routing with default settings. The bandwidths have been configured correctly for each link. If the T1 link between router A and router E fails, what path will a packet from router A take to reach the LAN attached to router F when the network has converged? A, B, C, F A, B, C, E, F A, D, G, E, F A, D, G, H, F 76. Which candidate route has the longest match for a packet with a destination address of 10.30.16.48? 10.30.0.0/16 10.30.15.0/23 10.30.16.0/24 10.30.16.32/27 10.30.16.32/30 77.

Refer to the exhibit. The network is configured with RIPv2. However, network administrators notice that communication cannot be successfully completed from one LAN to another. A network administrator issues the show ip route command on the HQ router. Based on the output, what should be done to correct the problem? Disable the load balancing feature of RIPv2. Issue the no auto-summary command for RIPv2.

Replace RIPv2 with EIGRP which supports VLSM. Make sure that the network statements include the correct subnet mask.

78. Refer to the exhibit. Why is the state of the serial0/0/0 interface administratively down? An IP address has not been configured on the interface. The WIC was installed into the incorrect slot on the router. The default encapsulation on the interface has been modified. The no shutdown command has not been executed on the interface. 79.

Refer to the exhibit. How was the OSPF default gateway entry for R2 determined? Default routes are automatically injected by OSPF into all advertisements. A static default gateway route is defined in the configuration of R2. The default-information originate command is applied on R1. The ISP defines the gateway of last resort and automatically passes it to R1 and R2. The ip default-gateway command is applied on R2. 80.

Refer to the exhibit. RIPv1 has been properly configured on all routers in the network. However, users on LAN2 have intermittent connectivity with the users on LAN1 and LAN3. What is the cause of the problem? Both LAN networks are separated from router R2 with a variably subnetted Class C network 209.165.200.0/30. Neither router R1 nor router R3 has a static route configured that points to the variably subnetted 172.16.0.0/24 networks. Both routers R1 and R3 are sending the summarized 172.16.0.0/16 network to R2 in their RIPv1 routing updates. Both networks 172.16.1.0/24 and 172.16.100.0/24 are configured with a subnet mask different from the default classful mask. 81. What is a successor for a destination network in an EIGRP network? the next hop on a backup route with the largest feasible distance to the destination the next hop on a backup route with the smallest feasible distance to the destination the next hop on the primary route with the largest feasible distance to the destination the next hop on the primary route with the smallest feasible distance to the destination

82. Refer to the exhibit. Which route will be removed from the routing table if manual EIGRP summarization is disabled on the Serial0/0/0 interface of Router3? 0.0.0.0/0 172.16.0.0/16 172.16.1.0/24 172.16.3.0/30 83. Which port can be used for initial router configuration? AUX vty 0 s0/0/0 console 84. Which two link-state routing protocol challenges does OSPF resolve through the election of a DR? (Choose two.) the extensive flooding of LSAs throughout the OSPF area the excessive adjacencies when the number of routers increases the requirement for link-state database updates to be propagated between OSPF areas the heavy CPU load that is imposed because each router must compute shortest paths by using the SPF algorithm the requirement for each router to build a topological database of the internetwork to determine the shortest paths between networks 85. A routing table shows an EIGRP route to 192.168.1.0/24 with a metric of 301440. What other term also describes this EIGRP metric value? feasible distance reported distance feasible successor feasibility condition

86. Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1? The Dijkstra algorithm will calculate the feasible successor. DUAL will query neighbors for a route to network 192.168.1.0.

Neighbor 172.16.3.2 will be promoted to the feasible successor. Traffic destined to the 192.168.1.0 network will be dropped immediately due to lack of a feasible successor.

87. Refer to the exhibit. A network administrator is accessing router R1 from the console port. Once the administrator is connected to the router, which password should the administrator enter at the R1> prompt to access the privileged EXEC mode? Cisco001 Cisco123 Cisco789 Cisco901 88. On a router, which actions can be performed in user mode? perform password recovery make global configuration changes view status of various router functions make changes to a specified interface

89. Refer to the exhibit. All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be the cause of this problem? Because RIPv1 is a classless protocol, it does not support this access. *RIPv1 does not support discontiguous networks. RIPv1 does not support load balancing. RIPv1 does not support automatic summarization. 90. Which two statements are correct about the split horizon with poison reverse method of routing loop prevention? (Choose two.) It is enabled by default on all Cisco IOS implementations. *It assigns a value that represents an infinite metric to the poisoned route. It sends back the poisoned route update to the same interface from where it was received. It instructs routers to hold all changes that might affect routes, for a specified period of time. *It limits the number of hops a packet can traverse through the network before it is discarded. 91. What are two reasons for the occurrence of a routing loop? (Choose two.) slow convergence *incorrectly configured static routes

routes that are learned via two routing protocols *static and dynamic routing being used on the same router lack of a default route on the router that connects to the Internet

92. Refer to the exhibit. Although R2 is configured correctly, host A is unable to access the Internet. What are two static routes that can be configured on R1, either of which would enable Internet connectivity for host A? (Choose two.) ip route 0.0.0.0 0.0.0.0 Fa0/0 *ip route 0.0.0.0 0.0.0.0 Fa0/1 ip route 0.0.0.0 0.0.0.0 10.1.1.1 *ip route 0.0.0.0 0.0.0.0 10.1.1.2 ip route 209.165.202.0 255.255.255.0 10.1.1.1 93. What is the function of the OSPF LSR packet? It is used to confirm the receipt of LSUs. It is used to establish and maintain adjacency with other OSPF routers. *It is used by the receiving routers to request more information about any entry in the DBD. It is used to check the database synchronization between routers 94. Which two technologies can be used in distance vector routing protocols to prevent routing loops? (Choose two.) authentication link-state advertisements *hold-down timers Spanning Tree Protocol *split horizon

95.

Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to R3. Which subnet address should be used for the new subnet that provides enough addresses while wasting a minimum of addresses? 192.168.1.0/24 192.168.1.48 / 28 192.168.1.32/27 *192.168.1.64/26 96. A network administrator uses the RIP routing protocol to implement routing within an autonomous system. What are two characteristics of this protocol? (Choose two.) *It uses the Bellman-Ford algorithm to determine the best path. It displays an actual map of the network topology. It offers rapid convergence in large networks. *It periodically sends complete routing tables to all connected devices. It is beneficial in complex and hierarchically designed networks. 97.

Refer to the exhibit. What is the meaning of the highlighted value 2? It is the administrative distance of the routing protocol. *It is the number of hops between R2 and the 192.168.8.0/24 network. It is the value used by the DUAL algorithm to determine the bandwidth for the link. It is the convergence time measured in seconds. 98. Refer to the exhibit. The routers are properly configured using a dynamic routing protocol with default settings, and the network is fully converged. Router A is forwarding data to router E. Which statement is true about the routing path? *If the network uses the RIP protocol, router A will determine that all paths have equal cost. If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table. If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest cost. If both RIP and EIGRP protocols are configured on router A, the router will use the route information that is learned by the RIP routing protocol. 99. Refer to the exhibit. All routers are running the same routing protocol. Based on the exhibit and its displayed commands, which statement is true? The wildcard mask is incorrectly configured. A default route must be configured on every router. Routers B, C, and D have no access to the Internet. *The link to the ISP is not advertised by the routing protocol process.

100. Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hosts on the Internet fail. What is the reason for this problem? The FastEthernet interface of R1 is disabled. *One of the default routes is configured incorrectly. A routing protocol is not configured on both routers. The default gateway has not been configured on host A. 101.

Refer to the exhibit. While trying to diagnose a routing problem in the network, the network administrator runs the debug ip rip command. What can be determined from the output of this command? The router is broadcasting RIP updates. The router will be unable to ping 192.168.1.2. The router is directly connected to network 172.16.1.0 /24. *The router has two interfaces that participate in the RIP process. 102. A router boots and enters setup mode. What is the reason for this? The IOS image is corrupt. Cisco IOS is missing from flash memory. *The configuration file is missing from NVRAM.

The POST process has detected hardware failure.

103. Refer to the exhibit. Which three statements are true of the routing table for Router1? (Choose three.) The route to network 172.16.0.0 has an AD of 156160. Network 192.168.0.16 can best be reached using FastEthernet0/0. *The AD of EIGRP routes has been manually changed to a value other than the default value. *Router1 is running both the EIGRP and OSPF routing process. Network 172.17.0.0 can only be reached using a default route. *No default route has been configured.

104. A network administrator has enabled RIP on routers B and C in the network diagram. Which of the following commands will prevent RIP updates from being sent to Router A? A(config)# router rip A(config-router)# passive-interface S0/0 B(config)# router rip B(config-router)# network 192.168.25.48 B(config-router)# network 192.168.25.64 A(config)# router rip A(config-router)# no network 192.168.25.32 *B(config)# router rip B(config-router)# passive-interface S0/0 A(config)# no router rip 105.

Refer to the exhibit. The show cdp neighbors command was run at R1. Which two facts about the newly detected device can be determined from the output? (Choose two.) *ABCD is a router that is connected to R1. ABCD is a non-CISCO device that is connected to R1. *The device is connected at the Serial0/0/1 interface of R1. R1 is connected at the S0/0/1 interface of device ABCD. ABCD does not support switching capability. 106. Refer to the exhibit. What action will R2 take for a packet that is destined for 192.168.2.0? It will drop the packet. It will forward the packet via the S0/0/0 interface. It will forward the packet via the Fa0/0 interface. *It will forward the packet to R1. 107 107. Which two statements are true about the EIGRP successor route? (Choose two.) It is saved in the topology table for use if the primary route fails. *It may be backed up by a feasible successor route. *It is used by EIGRP to forward traffic to the destination. It is flagged as active in the routing table. After the discovery process has occurred, the successor route is stored in the neighbor table.

108. Refer to the exhibit. Which two facts can be derived from this output? (Choose two.) *Three network devices are directly connected to Router2. *The serial interface between Router2 and Router3 is up. Router1 and Router3 are directly connected. Six devices are up and running on the network. Layer 3 functionality between routers is configured properly.

109. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network? *D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0 O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0

R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0 I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

110. Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1. What is the reason for the ping failure? The serial interface between two routers is down. R2 is not forwarding the routing updates. *The 192.168.4.0 network is not included in the RIP configuration of R2. RIPv1 needs to be configured.

111. Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this? The two routers are connected on a multiaccess network. *The hello and dead intervals are different on the two routers. They have different OSPF router IDs. They have different process IDs.

112. Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What two configuration changes will correct the problem? (Choose two.) Set a lower priority on R2. *Configure the routers in the same area. Set a lower cost on R2 compared to R1. Add a backup designated router to the network. *Match the hello and dead timers on both routers.

113. Refer to the exhibit. All routers are properly configured to use the EIGRP routing protocol with default settings, and the network is fully converged. Which statement correctly describes the path that the traffic will use from the 10.1.1.0/24 network to the 10.1.2.0/24 network? It will use the A-D path only. It will use the path A-D, and the paths A-C-D and A-B-D will be retained as the backup paths. It will use all the paths equally in a round-robin fashion. *The traffic will be load-balanced between A-B-D and A-C-D.

114. Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28? Router1 Router2 Router3 *Router4

115. Refer to the exhibit. The network has three connected routers: R1, R2, and R3. The routes of all three routers are displayed. All routers are operational and pings are not blocked on this network. Which ping will fail? from R1 to 172.16.1.1 from R1 to 192.168.3.1 from R2 to 192.168.1.1 from R2 to 192.168.3.1 116. Refer to the exhibit. Router R2 is configured properly and all interfaces are functional. Router R1 has been installed recently. Host A is unable to ping host B. Which procedure can resolve this problem? Configure a static route on R1 using the IP address of the serial interface on R1. Configure a default route on R1 with the exit interface Fa0/0 on R1. *Configure a static route on R1 using the IP address of S0/0/0 on R2. Configure a default route on R1 using the IP address of Fa0/0 on R2. 117. Refer to the exhibit. To implement the RIPv2 protocol, the network administrator runs the commands as displayed. However, the show ip protocol command fails to display any output.

How can the administrator solve the problem that is indicated by the lack of output from this command? Include the default-information originate command. Include the no auto-summary command. *Specify the network for which RIP routing has to be enabled. Implement RIPv2 authentication in the network.

118. Refer to the exhibit. A network administrator has configured R1 as shown, and all interfaces are functioning correctly. A ping from R1 to 172.16.1.1 fails. What could be the cause of this problem? The serial interface on R1 is configured incorrectly. *The default route is configured incorrectly. The default-information originate command must be issued on R1. Autosummarization must be disabled on R1.

119. Refer to the exhibit. A network administrator wants to reduce the size of the routing table of R1. Which partial routing table entry in R1 represents the route summary for R2, without including any additional subnets? 10.0.0.0/16 is subnetted, 1 subnets D 10.5.0.0[90/205891] via 192.168.1.2, S0/0/0 10.0.0.0/24 is subnetted, 4 subnets D 10.5.0.0[90/205198] via 192.168.1.2, S0/0/0 *10.0.0.0/22 is subnetted, 1 subnets D 10.5.0.0[90/205901] via 192.168.1.2, S0/0/0 10.0.0.0/8 is subnetted, 4 subnets D 10.5.0.0[90/205001] via 192.168.1.2, S0/0/0 120. Refer to the exhibit. Which two components are required to complete the configuration? (Choose two.) a crossover cable

a DCE device *a DTE device a modem *a V.35 cable 121. Refer to the exhibit. The output of the show ip route command for router R1 is displayed. What action will the router take for a packet that is destined for 192.168.1.5? *It will drop the packet. It will forward the packet to interface Serial0/0/0. It will determine the route for the packet through a routing protocol. It will forward the packet to the default gateway. 122. Refer to the exhibit. A network administrator has run the show interface command. The output of this command is displayed. What is the first step that is required to make this interface operational? Switch the cable with a known working cable. *Issue the no shutdown command on the interface. Configure the interface as a loopback interface. Set the encapsulation for the interface. 123. What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency? (Choose two.) The routers must elect a designated router. *The routers must agree on the network type. *The routers must use the same dead interval. The routers must exchange link state requests. The routers must exchange database description packets.

124. Refer to the exhibit. All interfaces are addressed and functioning correctly. The network administrator runs the tracert command on host A. Which two facts could be responsible for the output of this command? (Choose two.) The gateway for Host A is missing or improperly configured. The gateway for Host B is missing or improperly configured. The entry for 192.168.1.0/24 is missing from the routing table of R1. *The entry for 192.168.1.0/24 is missing from the routing table of R2. *The entry for 192.168.2.0/24 is missing from the routing table of R1. The entry for 192.168.2.0/24 is missing from the routing table of R2. 125. Refer to the exhibit. How many routes are ultimate routes? *3 4 5 7 126. Refer to the exhibit. Which summarization should R1 use to advertise its networks to R2? 192.168.1.0/24 192.168.0.0/24 *192.168.0.0/22 192.168.1.0/22

127. What are two functions of a router? (Choose two.) *It forwards data packets toward their destination.

It forwards the packet to the destination if the TTL value is 0. It changes the destination IP address of data packets before forwarding them to an exit interface. It determines the best path based on the destination MAC address. *It acts as an intersection between multiple IP networks. 128. Which two components are used to determine the router ID in the configuration of the OSPF routing process? (Choose two.) the IP address of the first FastEthernet interface the highest IP address of any logical interface *the highest IP address of any physical interface the default gateway IP address *the priority value of 1 on any physical interface

129. Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which two facts are true about the forwarding of route information by R1? (Choose two.) *R1 will forward the route information for subnet 192.168.100.0/30. *R1 will not forward route information for subnet 192.168.100.4/30. R1 will forward the route information with an administrative distance set to 50. R1 will forward the summarized route information for network 192.168.100.0/24. R1 will forward route information for subnet 10.10.10.0/30 out the serial interface. 56

130. Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.) *All routes are stable. Each route has one feasible successor. The serial interface between the two routers is down. The administrative distance of EIGRP has been set to 50. *The show ip eigrp topology command has been run on R1. 131. A router has learned two equal cost paths to a remote network via the EIGRP and RIP protocols. Both protocols are using their default configurations. Which path to the remote network will be installed in the routing table?

*the path learned via EIGRP the path learned via RIP the path with the highest metric value both paths with load balancing

132. Refer to the exhibit. Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols. Which path will be used to transmit the data packets from PC1 to PC2? *The packets will travel via R2-R1. The packets will travel via R2-R3. The traffic will be load-balanced between two paths via R2-R1 and via R2-R3. The packets will travel via R2-R3, and the other path via R2-R1 will be retained as the backup path. 133. Which statement is true about the RIPv1 protocol? It is a link-state routing protocol. *It excludes subnet information from the routing updates. It uses the DUAL algorithm to insert backup routes into the topology table. It uses classless routing as the default method on the router.