TL082

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier

Literature Number: SNOSBW5B

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier

August 2000

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier

General Description
These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage (BI-FET II technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift.

Features
n n n n n n n n n n n Internally trimmed offset voltage: Low input bias current: Low input noise voltage: Low input noise current: Wide gain bandwidth: High slew rate: Low supply current: High input impedance: Low total harmonic distortion: Low 1/f noise corner: Fast settling time to 0.01%: 15 mV 50 pA 16nV/Hz 0.01 pA/Hz 4 MHz 13 V/s 3.6 mA 1012 0.02% 50 Hz 2 s

Typical Connection

Connection Diagram
DIP/SO Package (Top View)

00835703 00835701

Order Number TL082CM or TL082CP See NS Package Number M08A or N08E

Simplified Schematic

00835702

BI-FET II is a trademark of National Semiconductor Corp.

2004 National Semiconductor Corporation

DS008357

www.national.com

TL082

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Power Dissipation Operating Temperature Range Tj(MAX) Differential Input Voltage

Input Voltage Range (Note 3) Output Short Circuit Duration Storage Temperature Range Lead Temp. (Soldering, 10 seconds) ESD rating to be determined.

15V
Continuous 65C to +150C 260C

18V
(Note 2) 0C to +70C 150C

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits.

30V
(Note 5) Conditions Min RS = 10 k, TA = 25C Over Temperature RS = 10 k Tj = 25C, (Notes 5, 6) Tj 70C Tj = 25C, (Notes 5, 6) Tj 70C Tj = 25C VS = 15V, TA = 25C VO = 10V, RL = 2 k Over Temperature 15 V/mV 25 TL082C Typ 5 10 25 50 1012 100 200 4 400 8 Max 15 20 mV mV V/C pA nA pA nA V/mV Units

DC Electrical Characteristics
Symbol VOS VOS/T IOS IB RIN AVOL Parameter Input Offset Voltage Average TC of Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Large Signal Voltage Gain

VO VCM CMRR PSRR IS

Output Voltage Swing Input Common-Mode Voltage Range Common-Mode Rejection Ratio Supply Voltage Rejection Ratio Supply Current

VS = 15V, RL = 10 k VS = 15V RS 10 k (Note 7)

12 11
70 70

13.5
+15 12 100 100 3.6 5.6

V V V dB dB mA

www.national.com

TL082

AC Electrical Characteristics
Symbol Parameter Amplifier to Amplifier Coupling SR GBW en in THD Slew Rate Gain Bandwidth Product Equivalent Input Noise Voltage Equivalent Input Noise Current Total Harmonic Distortion

(Note 5) Conditions Min TA = 25C, f = 1Hz20 kHz (Input Referred) VS = 15V, TA = 25C VS = 15V, TA = 25C TA = 25C, RS = 100, f = 1000 Hz Tj = 25C, f = 1000 Hz AV = +10, RL = 10k, VO = 20 Vp p, BW = 20 Hz20 kHz 0.01 pA/Hz % 8 13 4 25 V/s MHz nV/Hz TL082C Typ 120 Max dB Units

< 0.02

Note 2: For operating at elevated temperature, the device must be derated based on a thermal resistance of 115C/W junction to ambient for the N package. Note 3: Unless otherwise specified the absolute maximum negative input voltage is equal to the negative power supply voltage. Note 4: The power dissipation limit, however, cannot be exceeded. Note 5: These specifications apply for VS = 15V and 0C TA +70C. VOS, IB and IOS are measured at VCM = 0. Note 6: The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature, Tj. Due to the limited production test time, the input bias currents measured are correlated to junction temperature. In normal operation the junction temperature rises above the ambient temperature as a result of internal power dissipation, PD. Tj = TA + jA PD where jA is the thermal resistance from junction to ambient. Use of a heat sink is recommended if input bias current is to be kept to a minimum. Note 7: Supply voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously in accordance with common practice. VS = 6V to 15V.

Typical Performance Characteristics

Input Bias Current Input Bias Current

00835719 00835718

www.national.com

TL082

Typical Performance Characteristics

Supply Current

(Continued) Positive Common-Mode Input Voltage Limit

00835720

00835721

Negative Common-Mode Input Voltage Limit

Positive Current Limit

00835722

00835723

Negative Current Limit

Voltage Swing

00835724

00835725

www.national.com

TL082

Typical Performance Characteristics

Output Voltage Swing

(Continued) Gain Bandwidth

00835726 00835727

Bode Plot

Slew Rate

00835728

00835729

Distortion vs Frequency

Undistorted Output Voltage Swing

00835730

00835731

www.national.com

TL082

Typical Performance Characteristics

Open Loop Frequency Response

(Continued) Common-Mode Rejection Ratio

00835732

00835733

Power Supply Rejection Ratio

Equivalent Input Noise Voltage

00835734 00835735

Open Loop Voltage Gain (V/V)

Output Impedance

00835736

00835737

www.national.com

TL082

Typical Performance Characteristics

Inverter Setting Time

(Continued)

00835738

Pulse Response
Small Signal Inverting

Large Signal Inverting

00835708

00835706

Large Signal Non-Inverting

Small Signal Non-Inverting

00835709 00835707

www.national.com

TL082

Pulse Response

(Continued) Current Limit (RL = 100)

00835710

Application Hints
These devices are op amps with an internally trimmed input offset voltage and JFET input devices (BI-FET II). These JFETs have large reverse breakdown voltages from gate to source and drain eliminating the need for clamps across the inputs. Therefore, large differential input voltages can easily be accommodated without a large increase in input current. The maximum differential input voltage is independent of the supply voltages. However, neither of the input voltages should be allowed to exceed the negative supply as this will cause large currents to flow which can result in a destroyed unit. Exceeding the negative common-mode limit on either input will cause a reversal of the phase to the output and force the amplifier output to the corresponding high or low state. Exceeding the negative common-mode limit on both inputs will force the amplifier output to a high state. In neither case does a latch occur since raising the input back within the common-mode range again puts the input stage and thus the amplifier in a normal operating mode. Exceeding the positive common-mode limit on a single input will not change the phase of the output; however, if both inputs exceed the limit, the output of the amplifier will be forced to a high state. The amplifiers will operate with a common-mode input voltage equal to the positive supply; however, the gain bandwidth and slew rate may be decreased in this condition. When the negative common-mode voltage swings to within 3V of the negative supply, an increase in input offset voltage may occur. Each amplifier is individually biased by a zener reference which allows normal circuit operation on 6V power supplies. Supply voltages less than these may result in lower gain bandwidth and slew rate.

The amplifiers will drive a 2 k load resistance to 10V over the full temperature range of 0C to +70C. If the amplifier is forced to drive heavier load currents, however, an increase in input offset voltage may occur on the negative voltage swing and finally reach an active current limit on both positive and negative swings. Precautions should be taken to ensure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. Because these amplifiers are JFET rather than MOSFET input op amps they do not require special handling. As with most amplifiers, care should be taken with lead dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize pick-up and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ground. A feedback pole is created when the feedback around any amplifier is resistive. The parallel resistance and capacitance from the input of the device (usually the inverting input) to AC ground set the frequency of the pole. In many instances the frequency of this pole is much greater than the expected 3 dB frequency of the closed loop gain and consequently there is negligible effect on stability margin. However, if the feedback pole is less than approximately 6 times the expected 3 dB frequency a lead capacitor should be placed from the output to the input of the op amp. The value of the added capacitor should be such that the RC time constant of this capacitor and the resistance it parallels is greater than or equal to the original feedback pole time constant.

www.national.com

TL082

Detailed Schematic

00835711

Typical Applications
Three-Band Active Tone Control

00835712

www.national.com

TL082

Typical Applications

(Continued)

00835713

All potentiometers are linear taper Use the LF347 Quad for stereo applications
Note 8: All controls flat. Note 9: Bass and treble boost, mid flat. Note 10: Bass and treble cut, mid flat. Note 11: Mid boost, bass and treble flat. Note 12: Mid cut, bass and treble flat.

Improved CMRR Instrumentation Amplifier

00835714

C and are separate isolated grounds

Matching of R2s, R4s and R5s control CMRR With AVT = 1400, resistor matching = 0.01%: CMRR = 136 dB

Very high input impedance Super high CMRR

www.national.com

10

TL082

Typical Applications

(Continued) Fourth Order Low Pass Butterworth Filter

00835715

Fourth Order High Pass Butterworth Filter

00835716

11

www.national.com

TL082

Typical Applications

(Continued) Ohms to Volts Converter

00835717

www.national.com

12

TL082

Physical Dimensions
unless otherwise noted

inches (millimeters)

Order Number TL082CM NS Package M08A

Order Number TL082CP NS Package N08E

13

www.national.com

TL082 Wide Bandwidth Dual JFET Input Operational Amplifier

Notes

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONALS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no Banned Substances as defined in CSP-9-111S2.
National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Franais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560

2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Audio Amplifiers Data Converters DLP Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID OMAP Mobile Processors Wireless Connectivity www.ti.com/audio amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/omap www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Applications Communications and Telecom www.ti.com/communications Computers and Peripherals Consumer Electronics Energy and Lighting Industrial Medical Security Space, Avionics and Defense Video and Imaging www.ti.com/computers www.ti.com/consumer-apps www.ti.com/energy www.ti.com/industrial www.ti.com/medical www.ti.com/security www.ti.com/space-avionics-defense www.ti.com/video

Transportation and Automotive www.ti.com/automotive

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright 2011, Texas Instruments Incorporated