M6281, M6284, M6294 Modutrol IV Motors

SPECIFICATION DATA

FEATURES
Replace M944B,E,G,S Motors. Oil immersed motor and gear train for reliable performance and long life. Wiring box provides NEMA 3 weather protection. Quick-connect terminals standardscrew terminal adapter available. Adapter bracket for matching shaft height of older motors is standard with replacement motors. Die-cast aluminum housing.

u M6281 u M6284 u M6294

APPLICATION
These Modutrol Motors are 3-wire floating control motors with an internal, electrically isolated feedback potentiometer. These motors are used with controllers that provide floating or spdt output to operate dampers or valves.

Integral auxiliary switches are available factory mounted or can be field added to TRADELINE models. Electrically isolated feedback potentiometer provides indication of shaft position and can be used to slave Series 90 Motors or rebalance an external control circuit.

U.S. Registered Trademark Copyright 1996 Honeywell Inc. All Rights Reserved

63-1155-2

M6281, M6284, M6294 Modutrol IV MOTORS

SPECIFICATIONS
TRADELINE Models
TRADELINE models (M6284D1000, M6294D1008) are selected and packaged to provide ease of stocking, ease of handling, and maximum replacement value. TRADELINE model specifications are the same as those of standard models, unless specified otherwise. TRADELINE models have auxiliary switch cams.

Dead Weight Load on Shaft: Power or Auxiliary End: 200 lb (90.8 kg) maximum. Maximum Combined Load: 300 lb (136 kg). Dimensions: See Fig. 1. Ambient Temperature Ratings: Maximum: 150F (66C) at 25% duty cycle. Minimum: Minus 40F (-40C). Crankshaft: 3/8 in. (9.5 mm) square. M6284, M6294 have dual-ended shaft. M6281, M6291 have single-ended shaft. Feedback Potentiometer: 115 ohms. TRADELINE models are 600 ohms linear, configurable for W902 Control or for slaving Series 90 motor. Controller Type: 3-wire floating (Series 60)drive open, hold, drive closed. Internal, electrically isolated feedback potentiometer provides indication of motor position. Stroke: Fixed stroke models available with 90 or 160 stroke. Other models available with stroke field adjustable from 90 to 160. Start position of shaft changes with adjustment of stroke. (Midpoint of stroke remains fixed as stroke is adjusted. Stroke is adjusted by using cams located in wiring compartment.) Auxiliary Switch Ratings (Amperes): One Contact Rating a Amps Full Load Locked Rotor
a

Standard Models
M6281A,F M6284A,B,C,D,F M6294A,B,C,D
N N N N

Control Type 62 is Series 60 with internal feedback potentiometer Torque Rating 8 is high torque: 150 lb-in. at standard timing (60 sec. for 160) 9 is extra high torque: 300 lb-in. at 2 or 4 minute timing

Suffix Letter A: Fixed stroke (90 or 160), No auxiliary switches B: Fixed stroke (90 or 160), 1 auxiliary switch C: Fixed stroke (90 or 160), 2 auxiliary switches D: Adjustable stroke (90 to 160), No auxiliary switches F: Adjustable stroke (90 to 160), 2 auxiliary switches

Output Drive 4 is dual-ended shaft, non-spring return 1 is single-ended shaft, non-spring return NOTE: Some motors furnished to HVAC equipment manufacturers have a single-ended shaft, and no wiring box. Electrical Ratings: Voltage (V at 50/ Current 60 Hz) Draw (A) 24 120 208 240
a

120V 7.2 43.2

240V 3.6 21.6

40 VA pilot duty, 120/240 Vac on opposite contact.

Underwriters Laboratories Inc. Listed: File No. E4436, Guide No. XAPX. Power Consumption (W) 15 20 20 20 Canadian Standards Association Certified: General Listing File No. LR1620, Guide No. 400-E. Timing 90 Stroke Motors 15 sec 30 sec 1, 2 minb 160 Stroke Motors 30 sec 1 min 2, 4 minb 75 150 300 Torque in lb.-in (Nm) Normal Running (8.5) (17.0) (34.0) Breakaway a 150 300 600 (17.0) (34.0) (68.0)

M6281, M6284, M6294 Without Transformer a With Internal Transformer

0.69 0.21 0.12 0.11

Internal transformer can be field added.

Maximum Damper Rating: B dim Motor Torque lb-in. 75 150 300 in. 100 202 258 mm 2540 5131 6553

Breakaway torque is the maximum torque available to overcome occasional large loads such as a seized damper or valve. Motor must not be used continuously at this rating. b Stalling of 2 or 4 minute motor may damage drive shaft.

63-11552

M6281, M6284, M6294 Modutrol IV MOTORS

Accessories: ES650117 Explosion-proof Housing: encloses motor for use in explosive atmospheres. Not for use with Q601, Q618, and Q455 Linkages. To order, contact Nelson Electric Co., Order Services Dept., P.O. Box 726, Tulsa, OK, 74101, (918) 627-5530, for name of nearest local representative. Requires Honeywell 7617DM Coupling. Q607 External Auxiliary Switch: controls auxiliary equipment as a function of motor position. Internal Auxiliary Switch Kits: can be field-installed on TRADELINE models. 220736AOne-switch Kit. 220736BTwo-switch Kit. Q605 Damper Linkage: connects motor to damper. Includes motor crank arm. Q618 Linkage: connects Modutrol motor to water or steam valve. Q601 Bracket and Linkage Assembly: connects Modutrol motor to water or steam valve. Q100A,B Linkage: connects Modutrol motor to butterfly valve.

Q68 Dual Control Potentiometer: controls 1 to 9 additional motors. Q181 Auxiliary Potentiometer: controls 1 or 2 additional motors. 221455A Infinitely Adjustable Crank Arm: Approximately 0.75 in. (19 mm) shorter than the 4074ELY Crank Arm. Can rotate through downward position and clear base of motor without requiring use of adapter bracket. 220741A Screw Terminal Adapter: converts the standard quick-connect terminals to screw terminals. Transformers: mounted internally, provide 24 Vac power to motor 198162JA24 Vac; 50/60 Hz (for electrical isolation). 198162EA120 Vac; 50/60 Hz. 198162GA220 Vac; 50/60 Hz. 198162AA120/208/240 Vac; 50/60 Hz. 7617ADW Adjustable Crank Arm: Approximately 0.75 in. (19 mm) shorter than the 7616BR Crank Arm. Can rotate through downward position and clear base of motor without requiring use of the adapter bracket.

TOP VIEW OF 220738A BRACKET ONLY

4-7/8 (124) 3-15/16 (100)

4-7/32 (107) 5-13/16 (148) 2-5/16 (58) 7/16 (11) 5/8 (16)

5-1/2 (140)

21/32 (17)

9/32 (7)

1/2 (13) 15/16 (24) 4-1/16 (103)

13/16 (20)

1-15/32 (37)

1-1/2 (38) WIRING BOX

2-13/32 (61)

3/4 (19)

BASE MOTOR

AUXILARY END

POWER END

6-7/16 (164) 5-13/32 (137)

2-19/32 (66)

19/32 (15) 7-5/16 (185)

ADAPTER BRACKET

3/4 (19)
M302G

Fig. 1. M6284, M6294 mounting dimensions in in. (mm). Note: M6281 does not have auxiliary shaft. All other dimensions are the same.

POWER END
9/32 (7) 4-7/8 (124) 5-17/32 (141) 5/32 (4) 1-3/4 (44) 1-1/4 (32) 2-1/2 (64)

63-11552

M6281, M6284, M6294 Modutrol IV MOTORS

Home and Building Control Honeywell Inc. Honeywell Plaza P.O. Box 524 Minneapolis MN 55408-0524 Honeywell Latin American Division Miami Lakes Headquarters 14505 Commerce Way Suite 500 Miami Lakes FL 33016

Home and Building Control Honeywell Limited-Honeywell Limite 155 Gordon Baker Road North York, Ontario M2H 2C9 Honeywell Europe S.A. 3 Avenue du Bourget B-1140 Brussels Belgium

Honeywell Asia Pacific Inc. Room 3213-3225 Sun Hung Kai Centre No. 30 Harbour Road Wanchai Hong Kong

Helping You Control Your World