This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

Ingots and castings

Australian Standard

Copper and copper alloys—

AS 1565—1996
 This Australian Standard was prepared by Committee MT/2, Copper and Copper
Alloys. It was approved on behalf of the Council of Standards Australia on
17 May 1996 and published on 5 September 1996.

The following interests are represented on Committee MT/2:

AUSTAP
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

Australian Foundry Institute

Hunter Water Corporation, Australia
Metal Trades Industry Association of Australia
New Zealand Manufacturers Federation
Welding Technology Institute of Australia

Additional interests participating in preparation of Standard:

Non-ferrous foundries

Review of Australi an Standards. To keep abreast of progress in industry, Australian Standards are subject
to periodic review and are kept up to date by the issue of amendments or new edit ions as necessary. It is
important therefore that Standards users ensure that they are in possession of the latest editi on, and any
amendments thereto.
Full details of all Australi an Standards and related publi cati ons will be found in the Standards Australi a
Catalogue of Publications; this information is supplemented each month by the magazine ‘The Australi an
Standard’, which subscribing members receive, and which gives detail s of new publications, new edit ions
and amendments, and of withdrawn Standards.
Suggesti ons for improvements to Australi an Standards, addressed to the head off ice of Standards Australia,
are welcomed. Noti fication of any inaccuracy or ambiguit y found in an Australian Standard should be made
without delay in order that the matt er may be investigated and appropriate acti on taken.

This Standard was issued in draft form for comment as DR 95207.

 AS 1565—1996

Australian Standard
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

Copper and copper alloys—

Ingots and castings

PUBLISHED BY STANDARDS AUSTRALIA

(STANDARDS ASSOCIATION OF AUSTRALIA)
1 THE CRESCENT, HOMEBUSH, NSW 2140
ISBN 0 7337 0624 X
 AS 1565—1996 2

PREFACE

This Standard was prepared by the Joint Standards Australia/Standards New Zealand
Committee MT/2, Copper and Copper Alloys, to supersede AS 1565—1985. The grades of
copper and copper alloys and their compositions have been revised so that they align with
the current listing of the Unified Numbering System designations.
This Standard is the result of a consensus among Australian and New Zealand representatives
on the Joint Committee to produce it as an Australian Standard.
No International (ISO) Standards are available on the subject of copper and copper alloy
ingots and castings.
The objective of this Standard is to specify the requirements for the manufacture and testing
of copper and copper alloy ingots and castings.
Statements expressed in mandatory terms in notes to tables are deemed to be requirements
of this Standard.
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

The term ‘informative’ has been used in this Standard to define the application of the
appendix to which it applies. An ‘informative’ appendix is only for information and guidance.

 Copyri ght STANDARDS AUSTRALIA

Users of Standards are reminded that copyright subsists in all Standards Austr alia publications and software. Except where the
Copyri ght Act all ows and except where provided for below no publi cati ons or software produced by Standards Austr alia may be
reproduced, stored in a retr ieval system in any form or transmitt ed by any means without prior permission in writ ing from
Standards Australi a. Permission may be conditi onal on an appropriate royalt y payment. Requests for permission and information on
commercial soft ware royalti es should be dir ected to the head off ice of Standards Australi a.
Standards Austr alia will permit up to 10 percent of the technical content pages of a Standard to be copied for use exclusively
in-house by purchasers of the Standard wit hout payment of a royalty or advice to Standards Austr alia.
Standards Austr alia wil l also permit the inclusion of it s copyright materi al in computer software programs for no royalt y
payment provided such programs are used exclusively in-house by the creators of the programs.
Care should be taken to ensure that materi al used is from the current edit ion of the Standard and that it is updated whenever the
Standard is amended or revised. The number and date of the Standard should therefore be clearly identif ied.
The use of materi al in print form or in computer software programs to be used commercially, with or without payment, or in
commercial contracts is subject to the payment of a royalty. This policy may be vari ed by Standards Austr alia at any ti me.
 3 AS 1565—1996

CONTENTS

Page

1 SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 REFERENCED DOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 DEFINITION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 DESIGNATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 MATERIALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6 FREEDOM FROM DEFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7 TEST PROCEDURES AND REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . 6
8 ROUNDING OF TEST RESULT VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
9 MARKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

APPENDICES
A PURCHASING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B CODING SYSTEM WHEN ADDITIONAL INSPECTION IS REQUIRED
FOR CASTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 19
C RELATED COMPOSITION SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .. 22
D COLOUR CODE FOR INGOTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
E SHAPES OF STAND ARD TEST BARS . . . . . . . . . . . . . . . . . . . . . . . . . .. 24
F A GUIDE TO ALLOY SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Originated as AS H13 — 1940 and AS H14 — 1940.

Previous editi on AS 1565— 1985.
Thir d editi on 1996.
 AS 1565— 1996 4

STANDARDS AUSTRALIA

Australian Standard
Copper and copper alloys—Ingots and castings

1 SCOPE This Standard specifies requirements for the manufacture and testing of high
conductivity copper castings and copper alloy ingots and castings.
NOTES:
1 Advice and recommendations on information to be supplied by the purchaser at the time of
enquiry or order are contained in Appendix A.
2 Provision has been made for additional inspection requirements for castings which can be
specified by a coding system (see Appendix B).
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

2 REFERENCED DOCUMENTS The following documents are referred to in this

Standard:
AS
1391 Methods for tensile testing of metals
1515 Copper alloys (all parts)
1696 Copper
1696.1 Part 1: Determination of phosphorus — Spectrophotometric method
1816 Metallic materials —Brinell hardness test
2062 Methods for non-destructive penetrant testing of products and components
2345 Dezincification resistance of copper alloys
2614 Copper and copper alloys — Sampling for chemical analysis and electrical resistivity
2700 Colour standards for general purposes
2706 Numerical values — Rounding and interpretation of limiting values
2883 Analysis of metals— Procedures for the setting up, calibration and standardization
of atomic emission spectrometers using arc/spark discharge
3641 Recommended practice for atomic emission spectrometric analysis
3641.1 Part 1: Principles and techniques
K208 Methods for the analysis of unalloyed copper
K208.1 Part 1: Method for the electrolytic determination of copper in unalloyed copper
containing not less than 99.85 percent copper
BS
5714 Method of measurement of resistivity of metallic materials
ASTM
E 53 Test methods for chemical analysis of copper

3 DEFINITION For the purpose of this Standard the definition below applies.
3.1 Cast —the product of one furnace melt, one crucible melt, or a number of furnace or
crucible melts that are aggregated and mixed prior to sampling.
NOTE: In respect to continuous melting for the production of castings, a ‘cast’ is defined as 500 kg
of melted metal.

COPYRIGHT
 This is a free preview. Purchase the entire publication at the link below:

AS 1565-1996, Copper and copper alloys - Ingots

and castings
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.

Looking for additional Standards? Visit SAI Global Infostore

Subscribe to our Free Newsletters about Australian Standards® in Legislation; ISO, IEC, BSI and more
Do you need to Manage Standards Collections Online?
Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation
Do you want to know when a Standard has changed?
Want to become an SAI Global Standards Sales Affiliate?

Learn about other SAI Global Services:

LOGICOM Military Parts and Supplier Database

Metals Infobase Database of Metal Grades, Standards and Manufacturers
Materials Infobase Database of Materials, Standards and Suppliers
Database of European Law, CELEX and Court Decisions

Need to speak with a Customer Service Representative - Contact Us