AV Receiver

DTR-30.3
Instruction Manual

Introduction

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN

AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safety Instructions

1. 2. 3. 4. 5. 6. 7. 8. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, PORTABLE CART WARNING tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to S3125A avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen into the apparatus, C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation, E. If the apparatus has been dropped or damaged in any way, and F. When the apparatus exhibits a distinct change in performance this indicates a need for service. 16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Dont put candles or other burning objects on top of this unit. 17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries. 18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

9.

10.

11. 12.

13. 14.

En

Precautions
1. Recording CopyrightUnless its for personal use only, recording copyrighted material is illegal without the permission of the copyright holder. 2. AC FuseThe AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. CareOccasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Dont use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering. 4. Power WARNING BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the units rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz). The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times. Pressing the [On/Standby] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet. Preventing Hearing Loss Caution Excessive sound pressure from earphones and headphones can cause hearing loss. Batteries and Heat Exposure Warning Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like. Never Touch this Unit with Wet HandsNever handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer from whom you purchased this unit. Handling Notes If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it. Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case. This units top and rear panels may get warm after prolonged use. This is normal. If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer from whom you purchased this unit or an experienced radio/TV technician for help.

5.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

6.

7.

Modle pour les Canadien

REMARQUE: CET APPAREIL NUMRIQUE DE LA CLASSE B EST CONFORME LA NORME NMB003 DU CANADA. Sur les modles dont la fiche est polarise: ATTENTION: POUR VITER LES CHOCS LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.

8.

En

Thank you for purchasing an Integra AV receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV receiver. Please retain this manual for future reference.

Supplied Accessories
Make sure you have the following accessories:
Indoor FM antenna ( page 21) AM loop antenna ( page 21) Power cord ( page 21) Speaker cable labels ( page 13) Speaker setup microphone ( page 31) Remote controller (RC-804M) and two batteries (AA/R6)
*

In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

Installing the batteries

Note If the remote controller doesnt work reliably, try replacing the batteries. Dont mix new and old batteries or different types of batteries. Batteries (AA/R6) If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Aiming the remote controller To use the remote controller, point it at the AV receivers remote control sensor, as shown below.
Remote control sensor AV receiver

Approx. 16 ft. (5 m)

En

Contents
Introduction
Important Safety Instructions ......................................... 2 Precautions....................................................................... 3 Supplied Accessories...................................................... 4 Features ............................................................................ 6 Front & Rear Panels......................................................... 8 Front Panel..................................................................... 8 Display............................................................................ 9 Rear Panel ................................................................... 10 Remote Controller.......................................................... 11 Controlling the AV Receiver ......................................... 11

Advanced Operations
Advanced Setup ............................................................. 42 On-screen Setup Menus............................................... 42 Common Procedures in Setup Menu ........................... 42 Input/Output Assign ...................................................... 43 Speaker Setup.............................................................. 44 Audio Adjust ................................................................. 48 Source Setup................................................................ 49 Listening Mode Preset.................................................. 54 Miscellaneous............................................................... 54 Hardware Setup............................................................ 55 Remote Controller Setup .............................................. 58 Lock Setup.................................................................... 58 Using the Audio Settings .............................................. 58 Zone 2.............................................................................. 60 Making Zone 2 Connections ......................................... 60 Setting the Zone 2 Out ................................................. 60 Controlling Zone 2 Components................................... 61 Using the 12V Triggers................................................. 62 Using the Remote Controller in Zone 2 and Multiroom Control Kits................................................ 63

Connections
Connecting the AV Receiver ......................................... 12 Connecting Your Speakers .......................................... 12 About AV Connections ................................................. 16 Connecting Components with HDMI ............................ 17 Connecting Your Components ..................................... 18 Connecting Integra/Onkyo u Components ................ 20 Connecting a Recording Component ........................... 20 Connecting the Antennas ............................................. 21 Connecting the Power Cord ......................................... 21

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock ........................ 64 Using the Onkyo Dock.................................................. 64 Controlling Your iPod/iPhone ....................................... 65 Controlling Other Components..................................... 67 Preprogrammed Remote Control Codes ...................... 67 Looking up for Remote Control Code ........................... 67 Entering Remote Control Codes................................... 67 Remote Control Codes for Integra/ Onkyo Components Connected via u ..................... 68 Resetting Remote Mode Buttons.................................. 68 Resetting the Remote Controller .................................. 68 Controlling Other Components ..................................... 68

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................... 22 Turning On ................................................................... 22 Turning Off ................................................................... 22 Playback.......................................................................... 23 Selecting the Language for the Onscreen Setup Menus.................................. 23 Playing the Connected Component.............................. 23 Controlling Contents of USB or Network Devices ........ 23 Understanding Icons on the Display............................. 24 Playing an iPod/iPhone via USB .................................. 24 Playing a USB Device .................................................. 25 Listening to Internet Radio ........................................... 25 Playing Music Files on a Server ................................... 26 Remote Playback ......................................................... 27 Listening to AM/FM Radio ............................................ 28 Using Basic Functions .................................................. 31 Using the Automatic Speaker Setup ............................ 31 Using the Listening Modes ........................................... 34 Using the Home Menu.................................................. 40 Using the Sleep Timer.................................................. 40 Setting the Display Brightness ..................................... 40 Displaying Source Information ..................................... 41 Changing the Input Display .......................................... 41 Muting the AV Receiver................................................ 41 Using Headphones....................................................... 41 Recording ..................................................................... 41

Appendix
Troubleshooting ............................................................. 70 Network/USB Features................................................... 76 Firmware Update ............................................................ 79 Connection Tips and Video Signal Path ...................... 82 About HDMI ..................................................................... 84 Using an RIHD-compatible TV, Player, or Recorder ... 85 Specifications ................................................................. 87 Video Resolution Chart.................................................. 88

To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press 8On/Standby ( 70).

En

Features
Amplifier
100 Watts/Channel @ 8 ohms (FTC) 160 Watts/Channel @ 6 ohms (IEC) 175 Watts/Channel @ 6 ohms (JEITA) Optimum Gain Volume Circuitry H.C.P.S. (High Current Power Supply) Massive High Power Transformer Jitter Cleaning Circuit Technology

Miscellaneous
40 FM/AM Presets Audyssey 2EQ*6 to correct room acoustic problems Audyssey Dynamic EQ*6 for loudness correction Audyssey Dynamic Volume*6 to maintain optimal listening level and dynamic range Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz) A/V Sync Control Function (up to 800 ms) Auto Standby Function On-Screen Display via HDMI Preprogrammed u-Compatible Remote

Processing
THX Select2 Plus*1 Certified Incorporates Qdeo*2 technology for HDMI Video Upscaling (to 4K Compatible). HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color*3, Lip Sync, DTS*4-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD*5, Dolby Digital Plus, DSD and Multi-CH PCM) Dolby Pro Logic IIz*5 and Audyssey DSX*6 Non-Scaling Configuration A-Form Listening Mode Memory Direct Mode Music Optimizer*7 for Compressed Digital Music files 192 kHz/24-bit D/A Converters Powerful and Highly Accurate 32-bit Processing DSP

Connections
6 HDMI*8 Inputs (1 on front panel) and 1 Output Integra/Onkyo p for System Control 4 Digital Inputs (2 Optical/2 Coaxial) Component Video Switching (2 Inputs/1 Output) Universal Port for the Dock for iPod/iPhone*9/HD Radio*10 tuner module (North American models)/ DAB+ tuner module (Australian models) Banana Plug-Compatible Speaker Posts Powered Zone 2 and Zone 2 Pre Out IR Input/Output and 12 V Trigger RS232 Port for Interface Control Bi-Amping Capability for FL/FR with SBL/SBR Analog RGB Video Input (D-sub 15) for PC Internet Radio Connectivity (SiriusXM Internet Radio/vTuner/Pandora/Rhapsody/Slacker/Mediafly/ Napster)
*

Services available may vary depending on the region.

Network Capability for Streaming Audio Files*11 Front-Panel USB Input for Memory Devices and iPod/iPhone*9 models (Enables Display of Album Artwork)

En

*1

THX and the THX logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights reserved.

*9

THX Select2 Plus Before any home theater component can be THX Select2 Plus certified, it must pass a rigorous series of quality and performance tests. Only then can a product feature the THX Select2 Plus logo, which is your guarantee that the Home Theater products you purchase will give you superb performance for many years to come. THX Select2 Plus requirements define hundreds of parameters, including power amplifier performance, and preamplifier performance and operation for both digital and analog domains. THX Select2 Plus receivers also feature proprietary THX technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback.
*2 *3 *4

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Made for iPod and Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
*10

Qdeo and QuietVideo are trademarks of Marvell or its affiliates. x.v.Color is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent #s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872; 7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos are trademarks of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved.
*5

HD Radio, HD Radio Ready, and the HD Radio Ready logo are proprietary trademarks of iBiquity Digital Corporation. This HD Radio Ready receiver is ready to receive HD Radio broadcasts when connected to the Onkyo UP-HT1 HD Radio tuner module (sold separately). *11 DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. *11 Windows and the Windows logo are trademarks of the Microsoft group of companies. * Xantech is a registered trademark of Xantech Corporation. * Niles is a registered trademark of Niles Audio Corporation.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX and the double-D symbol are trademarks of Dolby Laboratories.
*6

*7 *8

Manufactured under license from Audyssey Laboratories, Inc. U.S. and foreign patents pending. Audyssey 2EQ, Audyssey Dynamic EQ, Audyssey Dynamic Volume and Audyssey DSX are registered trademarks and trademark of Audyssey Laboratories, Inc. Music Optimizer is a trademark of Onkyo Corporation.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

En

Front & Rear Panels

Front Panel
(North American models)

bc

d e

h i j kl m n

(Australian models)

The page numbers in parentheses show where you can find the main explanation for each item. a 8On/Standby button (22) b Zone 2, Off buttons (61) c Zone 2 Level buttons (61) d Tone and Tone Level buttons (58) e Remote control sensor (4) f Display (9) g Listening Mode buttons (34) h Dimmer button (North American models) (40) i Memory button (28) j Tuning Mode button (28) k Display button (41) l Setup button (42) m Tuning, Preset (28 to 28), arrow and Enter buttons n Return button o Master Volume control (23) p Phones jack (41) q AUX Input HDMI jack (17) r Input selector buttons (23) s USB port (18) t AUX Input Video/Audio jack (18) u Setup Mic jack (31) v RT/PTY/TP button (Australian models) (29)

En

Display

ij

k
g Audio input indicators h Bi AMP indicator (15, 45) i Audyssey indicator (31, 49) Dynamic EQ indicator (49) Dynamic Vol indicator (50) j Headphone indicator (41) k Message area l MUTING indicator (41) m Volume level (23) n USB indicator (24, 25) o SLEEP indicator (40, 53)

no

For detailed information, see the pages in parentheses. a Speaker/channel indicators b Z2 (Zone 2) indicator (61) c Listening mode and format indicators (34, 59) d 1, 3 and cursor indicators (24) e NET indicator (25, 57) f Tuning indicators RDS indicator (Australian models) (29) AUTO indicator (28) TUNED indicator (28) FM STEREO indicator (28)

En

Rear Panel

b cd

h i

a DIGITAL IN COAXIAL and OPTICAL jacks b COMPONENT VIDEO IN and OUT jacks c ETHERNET port d FM ANTENNA jack and AM ANTENNA terminal e PC IN jack f HDMI IN and OUT jacks g UNIVERSAL PORT jack h IR IN and OUT jacks i 12V TRIGGER OUT jacks j RS232 jack* k AC INLET l u REMOTE CONTROL jack

m Composite video and analog audio jacks (BD/DVD IN, VCR/DVR IN and OUT, CBL/SAT IN, GAME IN, PC IN, TV/CD IN) n MONITOR OUT V jack o PRE OUT jacks (CENTER, FRONT, SURROUND, SURROUND BACK or FRONT HIGH, SUBWOOFER) p ZONE 2 PRE/LINE OUT jacks q SPEAKERS terminals (CENTER, FRONT, SURROUND, SURROUND BACK or FRONT HIGH, ZONE 2) See Connecting the AV Receiver for connection ( pages 12 to 21).
*

Terminal for Interface Control.

En

10

Remote Controller
Controlling the AV Receiver
To control the AV receiver, press Receiver to select Receiver mode. You can also use the remote controller to control Integra/Onkyo Blu-ray Disc/DVD player, CD player, and other components. See Entering Remote Control Codes for more details ( page 67). For detailed information, see the pages in parentheses. a 8Receiver button (22) b Remote Mode/Input Selector buttons (23) c Arrow q/w/e/r and Enter buttons d Setup button (42) e Listening Mode buttons (34) f Dimmer button (40) g Muting button (41) h Display button (41) i VOL q/w button (23) j Return button

a b

g h c i d c a d j k

k Home button (40, 58) l Sleep button (40) Controlling the tuner To control the AV receivers tuner, press Tuner (or Receiver). You can select AM or FM by pressing Tuner repeatedly. a Arrow q/w buttons (28) b D.TUN button (28) c Display button d CH +/ button (28)

e f b

e Number buttons (28)

En

11

Connections

Connecting the AV Receiver

Connecting Your Speakers
Connecting the Speaker Cables
The following illustration shows which speaker should be connected to each pair of terminals. If youre using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.
Surround right Surround left

Surround back/ Front high right Tip

Surround back/ Front high left

Front right

Front left

Center

You can specify whether surround back or front high speakers are connected in the Speaker Configuration menu ( page 45) or during Audyssey 2EQ Room Correction and Speaker Setup ( page 31).

Screw-type speaker terminals Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

1/2" to 5/8" (12 to 15 mm)

Banana Plugs (North American models) If you are using banana plugs, tighten the speaker terminal before inserting the banana plug. Do not insert the speaker code directly into the center hole of the speaker terminal. Push-type speaker terminals Strip 3/8" to 1/2" (10 to 12 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

3/8" to 1/2"(10 to 12 mm)

En

12

Speaker Configuration
The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically ( page 31) or manually ( page 44).
Number of channels Front speakers Center speaker Surround speakers Surround back speaker*1*2 Surround back speakers*2 Front high speakers*2
*1 *2

Speaker Connection Precautions

Read the following before connecting your speakers: (North American models) You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the builtin amp protection circuit may be activated. (Australian models) You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to 4ohms ( page 45). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the builtin protection circuit may be activated. Disconnect the power cord from the wall outlet before making any connections. Read the instructions supplied with your speakers. Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative () terminals only to negative () terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural. Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided. Be careful not to short the positive and negative wires. Doing so may damage the AV receiver. Make sure the metal core of the wire does not have contact with the AV receivers rear panel. Doing so may damage the AV receiver.

2 3 4 5 6 7 7

If youre using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals. Front high and surround back speakers cannot be used at the same time.

Attaching the Speaker Cable Labels

The speaker terminals are color-coded for identification purpose.
Speaker Front left, Front high left, Zone 2 left Front right, Front high right, Zone 2 right Center Surround left Surround right Surround back left Surround back right Color White Red Green Blue Gray Brown Tan

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

En

13

 Dont connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. Dont connect one speaker to several terminals.

Using Dipole Speakers

You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (A) should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers (B) should be positioned so that their arrows point toward each other, as shown.
A

TV/screen

Using a Powered Subwoofer

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results. You can connect the powered subwoofer with two SUBWOOFER PRE OUT jacks respectively. The same signal is output from each jack.
Tip If your subwoofer is unpowered and youre using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier. Powered subwoofer

LINE INPUT

LINE INPUT

LINE INPUT

LINE INPUT

Corner position

1/3 of wall position

En

14

Bi-amping the Front Speakers

Important:
When making the bi-amping connections, be sure to remove the jumper bars that link the speakers tweeter (high) and woofer (low) terminals. Bi-amping can be used only with speakers that support biamping. Refer to your speaker manual.

Bi-amping provides improved bass and treble performance. When bi-amping is used, the AV receiver is able to drive up to a 5.1 speaker system in the main room. Once youve completed the bi-amping connections as shown and turned on the AV receiver, you must set the speaker setting to enable bi-amping ( page 45).

Tweeter (high) Woofer (low)

Front right

Front left

Connecting a Power Amplifier

If you want to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speakers to the power amplifier. See the manuals supplied with your amplifier for details.
Note Specify None for the channel that you dont want to output ( page 45).

Power amplifier

En

15

About AV Connections
Connecting AV components
HDMI cable
: Video & Audio

Other cables

: Video : Audio

AV receiver

AV receiver

TV, projector, etc.

Blu-ray Disc/ DVD player

Game console

TV, projector, etc.

Blu-ray Disc/ DVD player

Game console

Before making any AV connections, read the manuals supplied with your AV components. Dont connect the power cord until youve completed and double-checked all AV connections. Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions). To prevent interference, keep audio and video cables away from power cords and speaker cables.

Right!

AV Cables and Jacks

Signal Video and Audio Video Cable HDMI Component video Jack
HDMI

Wrong!

Description HDMI connections can carry digital video and audio. Component video separates the luminance (Y) and color difference signals (PB, PR), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently). This is a conventional analog interface to connect a PC and a display device (also called D-Sub or D-subminiature).

Y PB PR

Green Blue Red

Analog RGB

Composite video
V

Yellow
OPTICAL

Composite video is commonly used on TVs, VCRs, and other video equipment. Optical digital connections allow you to enjoy digital sound such as PCM*, Dolby Digital or DTS. The audio quality is the same as coaxial. Coaxial digital connections allow you to enjoy digital sound such as PCM*, Dolby Digital or DTS. The audio quality is the same as optical. Analog audio connections (RCA) carry analog audio.

Audio

Optical digital audio Coaxial digital audio Analog audio (RCA)

L

Orange White Red

Available sampling rate for PCM input signal is 32/44.1/48/88.2/96 kHz. In case of an HDMI connection, 176.4/192 kHz is also available. Note

The AV receiver does not support SCART plugs. The AV receivers optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when its removed. Push plugs in all the way. Caution

To prevent shutter damage, hold the optical plug straight when inserting and removing.

En

16

Connecting Components with HDMI

VCR or DVD recorder/Digital Video Recorder

Game console

TV, projector, etc.

Blu-ray Disc/DVD player Personal computer Satellite/cable set-top box, etc. Camcorder

Connect your components to the appropriate jacks. The default input assignments are shown below. : Assignment can be changed ( page 43).
Jack Input HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 HDMI IN 5 AUX Input HDMI Output HDMI OUT Components Blu-ray Disc/DVD player VCR or DVD recorder/Digital Video Recorder Satellite/cable set-top box, etc. Game console Personal computer Camcorder TV, projector, etc. Assignable

See also: Connection Tips and Video Signal Path ( page 82) About HDMI ( page 84) Using an RIHD-compatible TV, Player, or Recorder ( page 85) Audio Return Channel (ARC) function Audio Return Channel (ARC) function enables an HDMI capable TV to send the audio stream to the HDMI OUT of the AV receiver.
This function can be used when: your TV is ARC capable, and the TV/CD input selector is selected, and HDMI Control (RIHD) is set to On( page 56), and Audio Return Channel is set to Auto ( page 57). Tip To listen to audio received by the HDMI IN jacks through your TVs speakers: Set the HDMI Control (RIHD) setting to On ( page 56) for an p-compatible TV. Set the Audio TV Out setting to On ( page 56) when the TV is not compatible with p, or the HDMI Control (RIHD) setting to Off. Set your Blu-ray Disc/DVD players HDMI audio output setting to PCM. To listen to TV audio through the AV receiver, see Connecting Your Components ( page 18). Note When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off. As the Audio TV Out setting is set to On ( page 56) to hear from your TV speakers, the sound will also be output from the AV receivers speakers if you adjust the volume of the AV receiver. Similarly, as the HDMI Control (RIHD) setting is set to On ( page 56) to hear from the speakers of an p-compatible TV, the AV receivers speakers will produce sound if you adjust the volume of the AV receiver, while the TV speakers will be muted. To stop the AV receivers speakers from producing sound, you can either change the settings on the AV receiver or on the TV, or turn down the volume of the AV receiver.

En

17

Connecting Your Components

The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings.

AB C

E F

Connect your components to the appropriate jacks. The default input assignments are shown below. See Connection Tips and Video Signal Path for more information ( page 82). : Assignment can be changed ( page 44).
No. A B C D Jack/Port USB*1 USB, AUX Input Video*2 AUX Input DIGITAL IN Video Audio L/R OPTICAL COAXIAL E COMPONENT VIDEO ETHERNET MONITOR OUT BD/DVD IN VCR/DVR IN CBL/SAT IN GAME IN PC IN TV/CD IN H I Note
*1 *2 *3

Components iPod/iPhone, MP3 player, USB flash drive iPod/iPhone (video playback) Camcorder, etc. 1 (GAME) 2 (TV/CD) 1 (BD/DVD) 2 (CBL/SAT) IN 1 (BD/DVD) IN 2 (CBL/SAT) OUT Game console TV, CD player Blu-ray Disc/DVD player Satellite/cable set-top box, RI dock, etc. Blu-ray Disc/DVD player, RI dock Satellite/cable set-top box, RI dock, etc. TV, projector, etc. Router TV, projector, etc. Blu-ray Disc/DVD player VCR or DVD recorder/digital video recorder, RI dock Satellite/cable set-top box, etc. Game console, RI dock Personal computer TV, CD player, cassette tape deck, MD, CD-R, Turntable*4, RI dock Personal computer Universal port option dock (UP-A1 etc.)

Assignable

F G

PC IN*3 UNIVERSAL PORT

Do not connect the AV receivers USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way. When USB input is selected, you can input video signals from the AUX Input Video jack. Video signals input from AUX Input Video will be output from the MONITOR OUT jack. When you connect your personal computer to PC IN and select the PC input selector, the video of the personal computer is output from HDMI OUT. However, if you have assigned HDMI IN to the PC input selector, the AV receiver will output signals received from HDMI IN instead of signals from PC IN. To have the signals output from PC IN, select - - - - - for PC in the HDMI Input setting ( page 43).

En

18

*4

Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesnt have it, youll need a commercially available phono preamp. If your turntable has a moving coil (MC) type cartridge, youll need a commercially available MC head amp or MC transformer as well as a phono preamp. See your turntables manual for details.

With connection D, you can enjoy Dolby Digital and DTS. (To record or listen the audio in Zone 2 as well, use D and G.) With connection G, you can listen to and record audio from external components while you are in Zone 2. With connection G, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect to the main stereo. How to record a video source With the connections described above, you cannot record the videos through the AV receiver. See Recording about connections for video recording ( page 41).

En

19

Connecting Integra/Onkyo u Components

1 2 3

Make sure that each Integra/Onkyo component is connected with an analog audio cable (connection G in the hookup examples) ( page 18). Make the u connection (see the illustration). If youre using an RI Dock, or cassette tape deck, change the Input Display ( page 41).

With u (Remote Interactive), you can use the following special functions: System On/Auto Power On When you start playback on a component connected via u while the AV receiver is on Standby, the AV receiver will automatically turn on and select that component as the input source. Direct Change When playback is started on a component connected via u, the AV receiver automatically selects that component as the input source. Remote Control You can use the AV receivers remote controller to control your other u-capable Integra/Onkyo components, pointing the remote controller at the AV receivers remote control sensor instead of the component. You must enter the appropriate remote control code first ( page 68).
e.g., CD player
R L ANALOG AUDIO OUT

e.g., DVD player Note

R L ANALOG AUDIO OUT

Use only u cables for u connections. u cables are supplied with Integra/Onkyo components. Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting additional u-capable components. Connect only Integra/Onkyo components to u jacks. Connecting other manufacturers components may cause a malfunction. Some components may not support all u functions. Refer to the manuals supplied with your Integra/Onkyo components. While Zone 2 is on, the System On/Auto Power On and Direct Change u functions do not work.

Connecting a Recording Component

See Recording for details on recording ( page 41).
Note The AV receiver must be turned on for recording. Recording is not possible while its in standby mode. If you want to record directly from your TV or playback VCR to the recording VCR without going through the AV receiver, connect the TV/VCRs audio and video outputs directly to the recording VCRs audio and video inputs. See the manuals supplied with your TV and VCR for details. Video signals connected to composite video inputs can be recorded only via composite video outputs. For example, if your TV/VCR is connected to a composite video input, the recording VCR must be connected to a composite video output. The surround sound and DSP listening modes cannot be recorded. Copy-protected Blu-ray Discs and DVDs cannot be recorded. Sources connected to a digital input cannot be recorded. Only analog inputs can be recorded. DTS signals will be recorded as noise, so dont attempt analog recording of DTS CDs or LDs.

L AUDIO IN

R VIDEO IN

VCR, DVD recorder, cassette tape deck, CDR, MD recorder, etc.

En

20

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver wont pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.
Caution

North American models

Australian models

Be careful not to injure yourself when using thumbtacks.

Push.

Insert wire.

Release.

Insert the plug fully into the jack.

Insert the plug fully into the jack.

Assembling the AM loop antenna

Thumbtacks, etc.

AM loop antenna (supplied) Note

Indoor FM antenna (supplied)

Once your AV receiver is ready for use, youll need to tune into a radio station and position the antenna to achieve the best possible reception. Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords. Tip If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Connecting the Power Cord

Connect the supplied power cord to the AV receivers AC INLET.

Note Before connecting the power cord, connect all of your speakers and AV components. Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit. Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment. Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

To AC wall outlet

Plug the power cord into an AC wall outlet.

En

21

Turning On & Basic Operations

Turning On/Off the AV Receiver

8On/Standby

8Receiver

Receiver

Turning On

Press 8On/Standby on the front panel. or Press Receiver followed by 8Receiver on the remote controller. The AV receiver comes on, the display lights.

Turning Off

Press 8On/Standby on the front panel. or Press Receiver followed by 8Receiver on the remote controller. The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip For details on power management settings, see Auto Standby ( page 57).

En

22

Playback
The on-screen menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings. This section describes the procedure for using the remote controller unless otherwise specified.

Controlling Contents of USB or Network Devices

See Controlling Other Components about the operation of other components ( page 67).
Press USB or NET first.

Selecting the Language for the Onscreen Setup Menus

You can determine the language used for the onscreen setup menus. See Language in the OSD Setup ( page 55).

h i a b c d e f g j k l m n o p q

Playing the Connected Component

Operating with the remote controller

1 2

Press Receiver followed by Input Selector. Start playback on the source component. See also: Playing an iPod/iPhone via USB ( page 24) Playing a USB Device ( page 25) Listening to Internet Radio ( page 25) Playing Music Files on a Server ( page 26) Remote Playback ( page 27) Listening to AM/FM Radio ( page 28) iPod/iPhone Playback via Onkyo Dock ( page 64) Controlling Other Components ( page 67) To adjust the volume, use VOL q/w. Select a listening mode and enjoy! See also: Using the Listening Modes ( page 34) Audyssey ( page 49)

a Top Menu This button displays the top menu for each media or service. b q/w and Enter These buttons navigate through the menus.

e/r
This button cycles through pages.

3 4

Playlist e/r
In Standard Mode (iPod/iPhone), this button selects playlists. c 1 This button starts playback. d 7 This button selects the beginning of the current song. Pressing this button twice selects the previous song. e 5 This button fast-reverses the current song. f 3 This button pauses playback. g Search You can toggle between the playback screen and the list screen during playback. h Display This button switches between song informations. i Album +/ In Standard Mode (iPod/iPhone), this button selects albums. j Menu This button returns to top menu of the Internet Radio service.

Operating on the AV receiver

1 2 3 4

Use the input selector buttons to select the input source. Start playback on the source component. To adjust the volume, use the Master Volume control. Select a listening mode and enjoy!

En

23

k Return This button returns to the previous menu. l 4 This button fast-forwards the current song. m 6 This button selects the next song. n 2 This button stops playback. o Mode You can switch between Standard Mode and Extended Mode during iPod/iPhone playback. p Random This button performs random playback. q Repeat Press this button repeatedly to cycle through the repeat modes. Note The buttons you can use will differ depending on the devices and media used for playback.

Playing an iPod/iPhone via USB

This section explains how to play music/video files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod with video, iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th generation), iPhone 4, iPhone 3GS, iPhone 3G, iPhone

1 2

Press USB to select the USB input. Connect the USB cable that comes with the iPod/iPhone to the USB port on the front of the AV receiver. While reading the contents of your iPod/iPhone, the message Connecting... appears on the display. The USB indicator lights. It will flash if the AV receiver cannot read the iPod/iPhone. Press Mode repeatedly to switch to Extended Mode (Music) or Extended Mode (Video). A list of your iPod/iPhone models contents appears. To open a folder, use q/w to select it, and then press ENTER.
Tip With the default settings, the iPod/iPhone is operated in Standard Mode. Pressing Mode repeatedly switches back to Standard Mode. When you disconnect the iPod/iPhone, the AV receiver stores the mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver will start in Extended Mode (Music) the next time you connect the iPod/iPhone. You can also use q/w, Enter and Tuning Mode buttons on the front panel. Tuning Mode allows you to switch modes. When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

Understanding Icons on the Display

This section describes icons that appear on the display during media playback.
Displayed Icons Icon Description Folder Track Playback Pause Fast Forward Fast Reverse Artist

Use q/w to select a music/video file, and press Enter or 1 to start playback.

Note Album Repeat One Track Repeat Folder (USB Device) Repeat Shuffle Shuffle Album (iPod/iPhone) Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message Connecting... appears on the display. If you connect an iPod or iPhone to the USB port on this device, no sound will be output from the headphones jack.

Extended Mode (Music) control

The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing.

En

24

Extended Mode (Video) control

The video content information is displayed (lists are displayed), and you can control the video content while looking at the screen. Top screen list: Movies, Music Videos, TV Shows, Video Podcasts, Rentals.
Note To view the video contents of your iPod/iPhone, connect it to the USB port and AUX Input Video jack on the AV receivers front panel, using the official Apple Composite AV Cable. Depending on your iPod/iPhone model and generation, the displayed items may vary and the support for Extended Mode (Video) is not guaranteed.

Listening to Internet Radio

You need to connect the AV receiver to your home network ( page 76). You can select Internet radio stations by connecting to the AV receiver from your computer and selecting stations in your web browser. Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may not be able to listen to some stations.
Note Services available may vary depending on the region. See the separate instructions for more information.

Standard Mode control

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller (USB).
Note The following iPod models are not supported in Standard Mode. (They can only be controlled in Extended Mode). iPod with video iPod nano (1st generation)

Listening to vTuner Internet Radio

This unit includes the full vTuner Internet Radio Service at no additional charge. Once you have connected your unit to the Internet you can select vTuner Internet Radio to search for and play Internet radio stations and podcasts at any time. To enhance your Internet radio experience, the http://onkyo.vtuner.com/ portal is available to you as an easy way to browse to find stations, set up/organize your favorites, add your own stations, get help, etc. After the first time you try vTuner Internet Radio on your unit you can use the MAC Address of your unit to create a member login account (email address and password) on the http://onkyo.vtuner.com/ portal. To verify your MAC Address, please see Network ( page 57).

Playing a USB Device

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players). See also: Network/USB Features ( page 76).

1 2 3

1 2 3 4

Press USB to select the USB input. Plug your USB device into the AV receivers USB port. The USB indicator lights. It will flash if the AV receiver cannot read the USB device. Press Enter. A list of the devices contents appears. To open a folder, use q/w to select it, and then press Enter. Use q/w to select a music file, and press Enter or 1 to start playback.

Press NET. The NET screen appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. Use q/w/e/r to select vTuner Internet Radio and then press Enter. Use q/w to select a program and then press Enter. Playback starts.

Tip Do not disconnect the USB device or USB cable that comes with iPod/iPhone to the USB port at the front of the AV receiver, while the message Connecting... appears on the display.

My Music 0 : 11 Greate Artist My Favorite

Press Menu to enable selection from the following menu items. Stations like this: Stations like the one currently being played back are displayed. Add to My Favorites: Adds a station to My Favorites list. Press Top Menu to go to the top menu of the Internet Radio services.
Tip By pressing Search, you can toggle between the playback screen and the radio list screen.

En

25

Listening to Other Internet Radio

To listen to other internet radio stations, insert the following step after step 1 in the Listening to vTuner Internet Radio section.

Playing Music Files on a Server

You need to connect the AV receiver to your home network ( page 76). This section explains how to play music files on a computer or media server through the AV receiver (Server Playback).

On your computer, start your web browser and enter the AV receivers IP address in the browsers Internet address (URL) field. The browser connects to the AV receiver (WEB Setup Menu).
Note The AV receivers IP address is shown on IP Address ( page 57). If youre using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you cant connect to the AV receiver, recheck the AV receivers IP address on the Network screen.

1 2 3 4

Start your computer or media server. Press NET. The NET screen appears. The NET indicator lights. If it flashes, confirm the network connection. Use q/w/e/r to select dlna, and press Enter.
Tip To go back to the previous screen, press Return.

2 3 4 5

Click on the My Favorites tab. Enter the preset name and Internet address (URL). Click Save to save the Internet radio station. The Internet radio station is then added to My Favorites.

Use q/w to select a server, and then press Enter. The menu is displayed according to the server functions.
Note The search function does not work with media servers which do not support this function. Photos and movies stored on a media server cannot be accessed from the AV receiver. Depending on the sharing settings in the media server, the AV receiver may not able to access the content. See the instruction manual of the media server.

Registering My Favorites*1
You can add the currently playing song or station to the My Favorites. You can save up to 40 Internet radio stations. Once you've added a station to the list, simply select it in the My Favorites menu, and then press Enter to start playback.
*1

Use q/w to select an item, and then press Enter or 1 to start playback.

From the search results you can save the stations and songs but cannot listen to them directly.
My favorite song 1 0 : 11 Artist name My favorite album

Top menu of Internet Radio Create new station: Add a favorite station or Internet radio to the My Favorites. Rename this station: You can rename the stations and songs saved in My Favorites list. Delete from My Favorites: You can delete the stations and songs saved in My Favorites list.

Note Depending on the media server, 5/4/3 may not work. If the message No Item. appears, this means that no information can be retrieved from the server. In this case, check your server, network, and AV receiver connections.

1 2 3

Press Menu with the station selected or while a song is playing. Use q/w to select Add to My Favorites, and press Enter. Use q/w/e/r to select OK, and then press Enter.
Tip If you choose to rename the station, see Name Edit ( page 51).

En

26

Windows Media Player 11 Setup

This section explains how to configure Windows Media Player 11 so that the AV receiver can play the music files stored on your computer.

Using Remote Playback

1 2 3

Start Windows Media Player 12. To enable remote playback, you must first configure Windows Media Player 12. Press NET. The NET screen appears. The NET indicator lights. If it flashes, verify the network connection. Use q/w/e/r to select dlna, and press Enter. A list of media server appears.
Note Remote playback cannot be used while the music files of another media server are being played. You must stop their playback first.

1 2 3 4 5

Start Windows Media Player 11. On the Library menu, select Media Sharing. The Media Sharing dialog box appears. Select the Share my media check box, and then click OK. Select the AV receiver in the list, and then click Allow. Click OK to close the dialog box. This completes the Windows Media Player 11 configuration. You can now play the music files in your Windows Media Player 11 library through the AV receiver.
Tip Windows Media Player 11 can be downloaded for free from the Microsoft web site.

On Windows Media Player 12, right-click on a music file. The right-click menu appears. For selecting another media server, select the desired media server from the Other Libraries menu on Windows Media Player 12. Select the AV receiver from the right-click menu. The Play to window appears and playback on the product starts. Operations during remote playback can be made from the Play to window of Windows 7 on your personal computer. During remote playback, operations (such as Playback, Pause, Fast Forward, Fast Rewind, Previous, Next, Repeat, Random) cannot be made. Adjusting the Volume You can adjust the volume by adjusting the volume bar in the Remote playback window. The default maximum volume level is 82 (0dB). If you wish to change this, enter the value from the Web Setup in your browser. The volume value of the remote window and the volume value of the AV receiver may not always match. Adjustments you make to the volume in the AV receiver will not be reflected in the Remote playback window.

Remote Playback
You need to connect the AV receiver to your home network ( page 76). Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network.

Windows Media Player 12 Setup

This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music files stored on your personal computer.

1 2 3 4 5

Start Windows Media Player 12. On the Stream menu, select Turn on media streaming. A dialog box appears. Move your cursor and click on Turn on media streaming. A list of media server appears. Wording may vary slightly depending on the network location. Select the product in the list, and then click Allowed. Click OK to close the dialog box. This completes the Windows Media Player 12 configuration. You can now play the music files in your Windows Media Player 12 library.

En

27

Listening to AM/FM Radio

This section describes the procedure using the buttons on the front panel unless otherwise specified.

Tuning into stations by frequency You can tune into AM and FM stations directly by entering the appropriate frequency.

On the remote controller, press Tuner repeatedly to select AM or FM, followed by D.TUN.

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. You can also change the frequency steps ( page 56).

(Actual display depends on the country.)

Press Tuner to select either AM or FM. In this example, FM has been selected. Each time you press Tuner, the radio band changes between AM and FM.
Band Frequency

Within 8 seconds, use the number buttons to enter the frequency of the radio station. For example, to tune to 87.5 (FM), press 8, 7, 5. If you have entered the wrong number, you can retry after 8 seconds.

Presetting AM/FM Stations

(Actual display depends on the country.) You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.

1
Tuning into Radio Stations
Auto tuning mode

Tune into the AM/FM station that you want to store as a preset. See the previous section. Press Memory. The preset number flashes.

1 2

Press Tuning Mode so that the AUTO indicator lights on the display. Press Tuning q/w. Searching stops when a station is found. When tuned into a station, the TUNED indicator lights. When tuned into a stereo FM station, the FM STEREO indicator lights on the display, as shown.
TUNED AUTO

(Actual display depends on the country.)

3 4

While the preset number is flashing (about 8 seconds), use Preset e/rto select a preset from 1 through 40. Press Memory again to store the station or channel. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite FM/AM radio stations.

FM STEREO
Tip Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

Note You can name your radio presets for easy identification ( page 51). Its name is displayed instead of the band and frequency.

Manual tuning mode In manual tuning mode, FM stations will be in mono.

Selecting Presets

1 2

Press Tuning Mode so that the AUTO indicator goes off on the display. Press and hold Tuning q/w. The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.

To select a preset, use Preset e/r on the AV receiver, or the remote controllers CH +/.
Tip You can also use the remote controllers number buttons to select a preset directly.

En

28

 Deleting Presets

Displaying Radio Text (RT)

1 2

Select the preset that you want to delete. See the previous section. While holding down Memory, press Tuning Mode. The preset is deleted and its number disappears from the display.

Press RT/PTY/TP once. The RT information scrolls across the display.

Note The message Waiting may appear while the AV receiver waits for the RT information. If the message No Text Data appears on the display, no RT information is available.

Using RDS (Australian models)

RDS works only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator lights. When the station is broadcasting text information, the text can be displayed. What is RDS? RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. Many FM stations use it these days. In addition to displaying text information, RDS can also help you find radio stations by type (e.g., news, sport, rock, etc.). The AV receiver supports four types of RDS information: PS (Program Service) When tuned to an RDS station thats broadcasting PS information, the stations name will be displayed. Pressing Display will display the frequency for 3 seconds. RT (Radio Text) When tuned to an RDS station thats broadcasting text information, the text will be shown on the display as described in the next section. PTY (Program Type) This allows you to search for RDS radio stations by type ( page 29). TP (Traffic Program) This allows you to search for RDS radio stations that broadcast traffic information ( page 29).
Note In some cases, the text characters displayed on the AV receiver may not be identical to those broadcast by the radio station. Also, unexpected characters may be displayed when unsupported characters are received. This is not a malfunction. If the signal from an RDS station is weak, RDS data may be displayed intermittently or not at all.

Finding Stations by Type (PTY) You can search for radio stations by type.

1 2 3 4

Press RT/PTY/TP twice. The current program type appears on the display. Use Preset e/r to select the type of program you want. See the table shown later in this chapter. To start the search, press Enter. The AV receiver searches until it finds a station of the type you specified, at which point it stops briefly before continuing with the search. When a station you want to listen to is found, press Enter. If no stations are found, the message Not Found appears.

Listening to Traffic News (TP) You can search for stations that broadcast traffic news.

Press RT/PTY/TP three times. If the current radio station is broadcasting TP (Traffic Program), [TP] will appear on the display, and traffic news will be heard as and when its broadcast. If TP without square brackets appears, this means that the station is not broadcasting TP. To locate a station that is broadcasting TP, press Enter. The AV receiver searches until it finds a station thats broadcasting TP. If no stations are found, the message Not Found appears.

En

29

RDS program types (PTY)

Type None News reports Current affairs Information Sport Education Drama Culture Science and technology Varied Pop music Rock music Middle of the road music Light classics Serious classics Other music Weather Finance Childrens programmes Social affairs Religion Phone in Travel Leisure Jazz music Country music National music Oldies music Folk music Documentary Alarm test Alarm Display None News Affairs Info Sport Educate Drama Culture Science Varied Pop M Rock M Easy M Light M Classics Other M Weather Finance Children Social Religion Phone In Travel Leisure Jazz Country Nation M Oldies Folk M Document TEST Alarm!

En

30

Using Basic Functions

Using the Automatic Speaker Setup
With the supplied calibrated microphone, Audyssey 2EQ automatically determines the number of speakers connected, their size for purposes of bass management, optimum crossover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyssey 2EQ then removes the distortion caused by room acoustics by capturing room acoustical problems over the listening area in both the frequency and time domain. The result is clear, well-balanced sound for everyone. Audyssey 2EQ can be used with Audyssey Dynamic EQ and Audyssey Dynamic Volume ( pages 49, 50). Before using this function, connect and position all of your speakers. Audyssey 2EQ offers two ways of measuring: the Audyssey Quick Start and Audyssey 2EQ Full Calibration. Audyssey Quick Start uses the measurement from one position to perform the speaker setting only. Audyssey 2EQ Full Calibration uses the measurement from three positions to correct room response in addition to the speaker setting. The Quick Start takes about 2 minutes and Full Calibration takes about 10 minutes. Total measurement time varies depending on the number of speakers. The distances from position a to b and a to c must be at least 1 meter (3.3 ft).

TV

c ab
: Listening area Note Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measurements. Close windows, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics. The microphone picks up test tones played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup run. Audyssey 2EQ Room Correction and Speaker Setup cannot be performed while a pair of headphones is connected.

a to c: Listening position

1 2

Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver is connected. Set the speaker setup microphone at the Main Listening Position a, and connect it to the Setup Mic jack.
Setup Mic jack

Measurement procedure
To create a listening environment in your home theater that all listeners will enjoy, Audyssey 2EQ takes measurements at up to three positions within the listening area. Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce inaccurate results. a First measurement position Also referred to as the Main Listening Position this refers to the most central position where one would normally sit within the listening environment. Audyssey 2EQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer. b Second measurement position The right side of the listening area. c Third measurement position The left side of the listening area.

Speaker setup microphone

The speaker setting menu appears.

Note The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings.

En

31

When youve finished making the settings, press Enter.

2EQ: Auto Setup
AUDYSSEY

Speakers Type (Front) Powered Zone2 Surround Back/Front High

Normal No Surround Back

Use q/w to select a target, and use e/r to change the setting. After the results of Audyssey 2EQ have been saved, the menu will display the Audyssey ( page 49), Dynamic EQ ( page 49), Dynamic Volume ( page 50) settings.
Note When Audyssey Quick Start has been used for measurement, Audyssey cannot be selected. These settings are applied to all input selectors.

Perform the Speaker Setup according to your speaker configuration:

Speakers Type (Front) ( page 45) Powered Zone 2 ( page 45) Surround Back/Front High ( page 45)

When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the optional unit setting may appear on the speaker setting menu.

10 11

Press Enter. Disconnect the speaker setup microphone.

4 5

Use q/w to select Audyssey Quick Start or Audyssey 2EQ Full Calibration. Press Enter. Audyssey 2EQ Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey 2EQ Room Correction and Speaker Setup, unless you want to cancel the setup. If you select Audyssey Quick Start, you will go to step 8. Place the setup microphone at the next position, and then press Enter. Audyssey 2EQ performs more measurements. This takes a few minutes. When prompted, repeat step 6. Use q/w to select an option, and then press Enter.
2EQ: Auto Setup
AUDYSSEY

Note You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone. Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup. If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts. Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correction and Speaker Setup again, as room EQ characteristics may have changed.

6 7 8

-- Review Speaker Configuration -Subwoofer Front Center Surround Front High Surround Back Surround Back Ch Save Cancel : : : : : : : Yes Full Band 40Hz 100Hz None 120Hz 2ch

The options are: Save: Save the calculated settings and exit Audyssey 2EQ Room Correction and Speaker Setup. Cancel: Cancel Audyssey 2EQ Room Correction and Speaker Setup.
Note You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using e/r.

En

32

Error Messages
While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may appear.
2EQ: Auto Setup
AUDYSSEY

Changing the Speaker Setup Manually

You can manually make changes to the settings found during Audyssey 2EQ Room Correction and Speaker Setup. See also: Speaker Configuration ( page 45) Speaker Distance ( page 46) Level Calibration ( page 46) Equalizer Settings ( page 46)
Note Please note that THX recommends any THX main speakers be set to 80Hz(THX). If you set up your speakers using Audyssey 2EQ Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to 80Hz(THX) crossover ( page 45). Sometimes due to the electrical complexities of subwoofers and the interaction with the room, THX recommends setting the level and the distance of the subwoofer manually. Sometimes due to interaction with the room, you may notice irregular results when setting the level and/or distance of the main speakers. If this happens, THX recommends setting them manually.

Ambient noise is too high.

Error message

Retry Cancel

The options are: Retry: Try again. Cancel: Cancel Audyssey 2EQ Room Correction and Speaker Setup. Ambient noise is too high. The background noise is too loud. Remove the source of the noise and try again. Speaker Matching Error! The number of speakers detected was different from that of the first measurement. Check the speaker connection. Writing Error! This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact the dealer from whom you purchased this unit. Speaker Detect Error This message appears if a speaker is not detected. No means that no speaker was detected.
Tip See Speaker Configuration for appropriate settings ( page 13).

Using a Powered Subwoofer

If youre using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup. If the Subwoofer appears on the Review Speaker Configuration screen as No, increase the subwoofers volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the subwoofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofers instruction manual for details.

En

33

Using the Listening Modes

Selecting Listening Modes
See About Listening Modes for detailed information about the listening modes ( page 35). Listening Mode Buttons
Press Receiver first.

Movie/TV, Music, Game

Music Movie/TV Game THX

Movie/TV button This button selects the listening modes intended for use with movies and TV. Music button This button selects the listening modes intended for use with music.

Game button This button selects the listening modes intended for use with video games. THX button This button selects the THX listening modes.

The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). The listening modes you can select depends on the format of the input signal. To check the format, see Displaying Source Information ( page 41). While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

En

34

About Listening Modes

The AV receivers listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Explanatory Notes

be

a
a Front speakers b Center speaker c Surround speakers d Surround back speakers e Front high speakers f Subwoofers

Input Source The following audio formats are supported by the listening mode. A S D F G H
This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers. This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel). This is 7.1-channel surround sound. This is a further sound enhancement to 5.1 channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds. This is DTS-ES surround sound. This surround system can produce a discrete or a matrix-encoded sixth channel from existing DTS 5.1 encoded material. This is Dolby Digital EX surround sound. This provides a center back surround channel from 5.1-channel sources.

Speaker Layout The illustration shows which speakers are activated in each channel. See Speaker Configuration for the speaker setup ( page 45).

C B

N V

En

35

 Onkyo-Original DSP Listening Modes

Listening Mode Orchestra
Or ches t r a

Description Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

Input Source

Speaker Layout CN

Unplugged
Un p l u g g e d

Studio-Mix
S t u d i o M i x

A S D Suitable for acoustic instruments, vocals, and jazz, this mode emphasizes the F front stereo image, giving the impression of being right in front of the stage. G H Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert. This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices. In this mode, the sound has a dramatic feel with a similar atmosphere to Orchestra mode. In this mode, sound localization is distinct with emphasis on bass.

TV Logic
TV Log i c

Game-RPG
G ame RPG

Game-Action
G ame A c t i o n

Game-Rock
G ame R o c k

In this mode, sound pressure is emphasized to heighten live feel.

Game-Sports
G ame S p o r t s

In this mode, reverberation is increased and sound localization decreased slightly. Ideal for background music, this mode fills the entire listening area with stereo sound from the front, surround, and surround back speakers. In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room. With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listeners left and right ears. Good results may not be possible if theres too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb. ZXC N XCN

All Ch Stereo
A l l Ch S t e r eo

Full Mono
Fu l l Mo n o

T-D (TheaterDimensional)
TD

Listening Modes
Listening Mode Direct
D i r ec t

Description In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via Home menu is disabled. A/V Sync does not have effect on the analog audio. See Advanced Setup for more details ( page 42). Sound is output from the front left and right speakers and subwoofer.

Input Source A S D F G H

Speaker Layout ZXC N*1

Stereo
S t e r eo

ZXC N

Mono
Mo n o

Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs. This mode is for use with PCM multichannel sources. D F XCN

Multichannel
Mu l t i c h

En

36

Listening Mode

Description

Input Source

Speaker Layout

Dolby Pro Logic IIx*2 Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience Dolby Pro Logic II that fully envelops the listener. As well as music and movies, video games PL Mo v i e can also benefit from the dramatic spatial effects and vivid imaging.
PL PL PL PL PL x x x Mu s i c Game Mo v i e Mu s i c Game

If youre not using any surround back speakers, Dolby Pro Logic II will be S used instead of Dolby Pro Logic IIx Dolby PLIIx Movie Use this mode with any stereo or Dolby Surround (Pro Logic) movie (e.g., TV, DVD, VHS). Dolby PLIIx Music Use this mode with any stereo or Dolby Surround (Pro Logic) music source (e.g., CD, radio, cassette, TV, VHS, DVD). Dolby PLIIx Game Use this mode with video games, especially those that bear the Dolby Pro Logic II logo. Dolby PLIIx Movie Dolby PLIIx Music These modes use the Dolby Pro Logic IIx modes to expand 5.1-channel sources for 7.1-channel playback. D

XCN

Dolby Pro Logic IIz Height

PL z He i g h t

Dolby Pro Logic IIz Height is designed to more effectively use existing S program material when height channel speaker outputs are present. Dolby D Pro Logic IIz Height can be used to upmix a variety of sources from movies F and music, but are particularly well-suited to upmix game content. These modes expand 5.1-channel sources for 6.1/7.1-channel playback. Theyre especially suited to Dolby EX soundtracks that include a matrixencoded surround back channel. The additional channel adds an extra dimension and provides an enveloping surround sound experience, perfect for rotating and fly-by sound effects. In this mode, audio from the input source is output without surround-sound processing. The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via Home menu are enabled. See Advanced Setup for more details ( page 42). D H

Dolby EX
Do l b y Do l b y EX D EX

Dolby Digital
Do l b y D

XCN

Dolby Digital Plus*3

Do l b y D +

D F D F D

XCN XCN*1 XCN XCN*1 XCN

Dolby TrueHD
Do l b y T r u e HD

DTS
DTS

DTS-HD High Resolution Audio

D T S HD HR

D F D F D

XCN XCN*1 XCN XCN*1 XCN

DTS-HD Master Audio

D T S HD MS T R

DTS Express
DTS Exp r ess

DSD*4
DSD

DTS 96/24
DTS 96 / 24

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a 96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with DVDs that bear the DTS 96/24 logo.

XCN

DTS-ES Discrete*5
ES D i sc r e t e

This mode is for use with DTS-ES Discrete soundtracks, which use a G discrete surround back channel for true 6.1/7.1-channel playback. The seven totally separate audio channels provide better spatial imaging and 360degree sound localization, perfect for sounds that pan across the surround channels. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Discrete soundtrack. This mode is for use with DTS-ES Matrix soundtracks, which use a matrixencoded back-channel for 6.1/7.1-channel playback. Use it with DVDs that bear the DTS-ES logo, especially those with a DTS-ES Matrix soundtrack.

DTS-ES Matrix*5
ES Ma t r i x

En

37

Listening Mode Neo:6

Description This mode expands any 2-channel source for up to 7.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

Input Source

Speaker Layout

Ne o : 6 Ne o : 6

C i n ema Mu s i c

Neo:6 Cinema S Use this mode with any stereo movie (e.g., TV, DVD, VHS). Neo:6 Music Use this mode with any stereo music source (e.g., CD, radio, cassette, TV, VHS, DVD). Neo:6 This mode uses Neo:6 to expand 5.1-channel sources for 6.1/7.1-channel playback. D

XCN

Ne o : 6

Audyssey DSX*6
Audy s s e y DSX

Audyssey DSX D Audyssey DSX is a scalable system that adds new speakers to improve F surround impression. Starting with a 5.1 system Audyssey DSX adds only G height channels in this deployment. The pair of Height channels reproduce important acoustical and perceptual cues, which greatly enhance the surround experience. In addition to these new Height channels, Audyssey DSX applies Surround Envelopment Processing to enhance the blend between the front and surround channels. Dolby Pro Logic II Movie + Audyssey DSX S Dolby Pro Logic II Music + Audyssey DSX Dolby Pro Logic II Game + Audyssey DSX The combination of Dolby Pro Logic II and Audyssey DSX modes can be used. Founded by George Lucas, THX develops stringent standards that ensure movies are reproduced in movie theaters and home theaters just as the director intended. THX Modes carefully optimize the tonal and spatial characteristics of the soundtrack for reproduction in the home-theater environment. They can be used with 2-channel matrixed and multichannel sources. Surround back speaker output depends on the source material and the selected listening mode.

PL PL PL

Mo v i e Mu s i c Game

DSX DSX DSX

THX

THX

C i n ema

NHX : Mu s i c Teo 6 THX Game s

THX Cinema D THX Cinema mode corrects theatrical soundtracks for playback in a home F theater environment. In this mode, THX Loudness Plus is configured for G cinema levels and Re-EQ, Timbre Matching, and Adaptive Decorrelation are active. THX Music THX Music mode is tailored for listening to music, which is typically mastered at significantly higher levels than movies. In this mode, THX Loudness Plus is configured for music playback and only Timbre Matching is active. THX Games THX Games mode is meant for spatially accurate playback of game audio, which is often mixed similarly to movies but in a smaller environment. THX Loudness Plus is configured for game audio levels, with Timbre Matching active. Dolby Pro Logic II/IIx Movie + THX Cinema Dolby Pro Logic II/IIx Music + THX Music Dolby Pro Logic II/IIx Game + THX Games The combination of Dolby Pro Logic II/IIx*2 and THX Cinema/Music/Games modes can be used. The PLII or PLIIx indicator lights on the display. Dolby Pro Logic IIx Movie + THX Cinema Dolby Pro Logic IIx Music + THX Music The combination of Dolby Pro Logic IIx and THX Cinema/Music modes can be used. The PLIIx indicator lights on the display. Dolby Pro Logic IIz Height + THX Cinema Dolby Pro Logic IIz Height + THX Music Dolby Pro Logic IIz Height + THX Games The combination of Dolby Pro Logic IIz Height and THX Cinema/Music/Games modes can be used. The PLIIz indicator lights on the display. S

CN

CN

D H

En

S D F G H

38

Listening Mode

Description Neo:6 Cinema + THX Cinema Neo:6 Music + THX Music Neo:6 + THX Cinema Neo:6 + THX Music Neo:6 + THX Games The combination of Neo:6 and THX Cinema/Music/Games modes can be used. The Neo:6 indicator lights on the display.

Input Source S D H

Speaker Layout CN V

Teo 6 NHX : S 2 THX THX THX S2 S2

C i n ema Mu s i c Game EX

Su r r

THX Select2 Cinema D This mode expands 5.1-channel sources for 7.1- channel playback. It does this by analyzing the composition of the surround source, optimizing the ambient and directional sounds to produce the surround back channel output. THX Select2 Music This mode is designed for use with music. It expands 5.1-channel sources for 7.1-channel playback. THX Select2 Games This mode is designed for use with video games. It can expand 5.1-channel sources for 6.1/7.1-channel playback. THX Surround EX This mode expands 5.1-channel sources for 6.1/7.1- channel playback. Its especially suited to Dolby Digital EX sources. THX Surround EX, also known as Dolby Digital Surround EX, is a joint development between Dolby Laboratories and THX Ltd. Dolby Pro Logic II Game + THX Select2 Games The combination of Dolby Pro Logic II Game and THX Select2 Games modes can be used. The PLII indicator lights on the display. S

Note
*1 *2

When the input source contains the encoded front high channel, the corresponding speakers output the sound. If there are no surround back speakers, or Powered Zone 2 is being used, Dolby Pro Logic II is used. *3 For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system. *4 AV receiver can input the DSD signal from HDMI IN. Setting the output setting on the player side to PCM might obtain a better sound according to the player. In that case, set the output setting on the player side to PCM. *5 If there are no surround back speakers, DTS is used. *6 This listening mode can be selected only when all the following conditions are satisfied: Center speaker is connected. Front high speakers is connected. The listening modes cannot be selected with some source formats.

En

39

Using the Home Menu

The Home menu provides you quick access to frequently used menus without having to go through the long standard menu. This menu enables you to change settings and view the current information. The Home menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings.

Note
*1 *2

*3

For the Port input selector, the name of Universal Port Option Dock will be displayed. Only when you have selected Custom in the Picture Mode ( page 52), pressing Enter allows you to adjust the following items via the Home menu: Brightness, Contrast, Hue and Saturation. Press Return to return to the Picture Mode setting. Depending on the input source and listening mode, not all channels shown here output the sound.

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

1 2

Press Receiver followed by Home. The Home menu will be superimposed on the TV screen. Use q/w and Enter to make the desired selection. Input*1 You can select the input source while viewing the information as follows: the name of input selectors, input assignments, radio information, and ARC function setting. Press Enter to display the current input source, followed by q/w to select the desired input source. Pressing Enter again switches to the selected input source. Audio You can change the following settings: Bass, Treble, Subwoofer Level, Center Level, Audyssey, Dynamic EQ, Dynamic Volume, Late Night, Music Optimizer, Re-EQ and Re-EQ(THX). See also: Audyssey ( page 49) Using the Audio Settings ( page 58) Video You can change the following settings: Wide Mode and Picture Mode*2. See also: Picture Adjust ( page 52) Info*3 You can view the information of the following items: Audio, Video and Tuner. Listening Mode You can select the listening modes that are grouped in the following categories: MOVIE/TV, MUSIC, GAME and THX. Use q/w to select the category and e/r to select the listening mode. Press Enter to switch to the selected listening mode.

Press Receiver followed by Sleep repeatedly to select the required sleep time. The sleep time can be set from 90 to 10 minutes in 10 minute steps. The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.
Tip If you need to cancel the sleep timer, press Sleep repeatedly until the SLEEP indicator goes off. To check the time remaining until the AV receiver sleeps, press Sleep. Note that if you press again on Sleep as the time being displayed is equal or inferior to 10 minutes, the sleep timer will go off.

Setting the Display Brightness

You can adjust the brightness of the AV receivers display.

Press Receiver followed by Dimmer repeatedly to switch between: dim, dimmer, or normal brightness.
Tip (North American models) Alternatively, you can use the AV receivers Dimmer.

En

40

Displaying Source Information

You can display various information about the current input source as follows. (Components connected to the UNIVERSAL PORT jack are excluded.)

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press Receiver followed by Display repeatedly to cycle through the available information.

Press Receiver followed by Muting. The output is muted and the MUTING indicator flashes on the display.
Tip To unmute, press Muting again or adjust the volume. Muting is automatically cancelled when the AV receiver is set to standby.

The following information can typically be displayed.

Input source Listening mode

Using Headphones
Signal format*1 Sampling frequency Input signal resolution Output resolution Tip Alternatively, you can use the AV receivers Display.
*1

Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the Phones jack.
Note Always turn down the volume before connecting your headphones. While the headphones plug is inserted in the Phones jack, the speakers are turned off. (The Powered Zone 2 speakers are not turned off.) When you connect a pair of headphones, the listening mode is set to Stereo, unless its already set to Stereo, Mono or Direct. If you connect an iPod or iPhone to the USB port on this device, no sound will be output from the headphones jack.

If the input signal is analog, Analog is displayed. If the input signal is PCM, the sampling frequency is displayed. If the input signal is digital but not PCM, the signal format is displayed. Information is displayed for about three seconds, then the previously displayed information reappears.

Recording Changing the Input Display

When you connect an u-capable Integra/Onkyo component, you must configure the input display so that u can work properly. This setting can be done only from the front panel. This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources.

AV Recording
Audio sources can be recorded to a recorder (e.g., cassette tape deck, CDR, MD recorder). Video sources can be recorded to a video recorder (e.g., VCR, DVD recorder).

1 2

Press TV/CD, Game or VCR/DVR. TV/CD, GAME or VCR/DVR appears on the display. Press and hold down TV/CD, Game or VCR/DVR (about 3 seconds) to change the input display. Repeat this step to select the desired input display. TV/CD: TV/CD DOCK TAPE

Use the input selector buttons to select the source that you want to record. You can watch the source while recording. The AV receivers Master Volume control has no effect on recording. On your recorder, start recording. On the source component, start playback. If you select another input source during recording, that input source will be recorded.

Game: GAME DOCK VCR/DVR: VCR/DVR DOCK

Note DOCK can be selected for the TV/CD, Game or VCR/DVR input selector, but not at the same time. Enter the appropriate remote control code before using the remote controller for the first time ( page 67).

2 3

En

41

Advanced Operations

Advanced Setup
On-screen Setup Menus
The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the composite video MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings. This section describes the procedure for using the remote controller unless otherwise specified.

Common Procedures in Setup Menu

Remote indicator

Receiver

Enter q/w/e/r Setup

MENU a b c d e f g h i 1. 2. 3. 4. 5. 6. 7. 8. 9. Input/Output Assign Speaker Setup Audio Adjust Source Setup Listening Mode Preset Miscellaneous Hardware Setup Remote Controller Setup Lock Setup
f Miscellaneous ( page 54)
6. Miscellaneous 1. 2. 3. 4. 5. Volume Setup OSD Setup 12V Trigger A Setup 12V Trigger B Setup 12V Trigger C Setup

Return

The on-screen setup menus appear on the connected TV and provide a convenient way to change the AV receivers various settings. Settings are organized into 9 categories on the main menu. Carry out the settings by using the on-screen display.

Press Receiver followed by Setup.

Tip If the main menu doesnt appear, make sure the appropriate external input is selected on your TV.

a Input/Output Assign ( page 43)

1. Input/Output Assign 1. 2. 3. 4. Monitor Out HDMI Input Component Video Input Digital Audio Input

b Speaker Setup ( page 44)

2. Speaker Setup 1. 2. 3. 4. 5. 6. Speaker Settings Speaker Configuration Speaker Distance Level Calibration Equalizer Settings THX Audio Setup

g Hardware Setup ( page 55)

7. Hardware Setup 1. 2. 3. 4. 5. 6. 7. Remote ID MultiZone Tuner HDMI Auto Standby Network Firmware Update

2 3 4

Use q/w to select a menu, and then press Enter. Use q/w to select a target, and then press Enter. Use q/w to select an option, and use e/r to change the setting. Press Setup to close the menu. Press Return to return to the previous menu.

Note This procedure can also be performed on the AV receiver by using Setup, the arrow buttons, and Enter. During Audyssey 2EQ Room Correction and Speaker Setup, messages and alike that are displayed on the TV screen will appear on the display.

c Audio Adjust ( page 48)

3. Audio Adjust 1. 2. 3. 4. 5. 6. Multiplex/Mono Dolby DTS Audyssey DSX Theater-Dimensional LFE Level

h Remote Controller Setup ( page 67)

8. Remote Controller Setup 1. Remote Mode Setup

Explanatory Notes
i Lock Setup ( page 58)
9. Lock Setup Setup

d Source Setup ( page 49)

4. Source Setup 1. 2. 3. 4. 5. 6. Audyssey IntelliVolume A/V Sync Name Edit Picture Adjust Audio Selector

a b c

Main Menu

Speaker Configuration

Subwoofer Yes No a Menu selection b Setting target c Setting options (default setting underlined)

e Listening Mode Preset ( page 54)

5. Listening Mode Preset 1. 2. 3. 4. 5. 6. BD/DVD VCR/DVR CBL/SAT GAME PC AUX

En

42

Input/Output Assign
Main Menu Input/Output Assign

Monitor Out
You can specify the output resolution for the HDMI OUT and have the AV receiver upconvert the picture resolution as necessary to match the resolution supported by your TV. Resolution Through: Select this to pass video through the AV receiver at the same resolution and with no conversion. Auto: Select this to have the AV receiver automatically convert video at resolutions supported by your TV. 480p (480p/576p), 720p, 1080i, 1080p Select the desired output resolution. 1080p/24: Select this for 1080p output at 24 frames per second. 4K Upscaling: Select this for an output resolution four times that of 1080p, resulting in 3840 2160 pixels.
Note Depending on the incoming video signal, the video playback may not be smooth or the vertical resolution may be lowered. In this case select anything other than 1080p/24.

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TV/CD, PORT HDMI1, HDMI2, HDMI3, HDMI4, HDMI5: Select a corresponding HDMI input to which the video component has been connected. - - - - -: Select this to output composite video and component video sources from the HDMI OUT. The video signal from the HDMI output is configured in Component Video Input ( page 44).
*1

If you connect your personal computer to PC IN (Analog RGB), you must assign - - - - - to the PC input selector.

Each HDMI input cannot be assigned to two input selectors or more. When HDMI1 - HDMI5 have already been assigned, you must first set any unused input selectors to - - - - - or you will be unable to assign HDMI1 - HDMI5 to other input selectors.
Note When an HDMI IN is assigned to an input selector as explained here, the same HDMI IN will be set as a priority in the Digital Audio Input ( page 44). In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the Audio Selector setting ( page 53). The TUNER selector cannot be assigned and is fixed at the - - - - - option. AUX is used only for input from the front panel. Do not assign an HDMI IN to the TV/CD selector while HDMI Control (RIHD) is set to On ( page 56), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed. If you assign - - - - - to an input selector that is currently selected in HDMI Through ( page 56), the HDMI Through setting will be automatically switched to Off. If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the PORT selector.

HDMI Input
If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to HDMI IN 2, you must assign HDMI2 to the BD/DVD input selector. If youve connected your TV to the AV receiver with an HDMI cable, composite video and component video sources can be upconverted* to HDMI. See Video Connection Formats for more information on video signal flow and upconversion ( page 82).
Composite video, component video HDMI

IN

OUT
Composite video, component video HDMI

Here are the default assignments.

Input selector BD/DVD VCR/DVR CBL/SAT GAME PC AUX TV/CD PORT Default assignment HDMI1 HDMI2 HDMI3 HDMI4 HDMI5*1 FRONT (Fixed) ---------

En

43

Component Video Input

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to COMPONENT VIDEO IN 2, you must assign IN2 to the BD/DVD input selector. Here are the default assignments.
Input selector BD/DVD VCR/DVR CBL/SAT GAME PC AUX TV/CD PORT Default assignment IN1 ----IN2 ---------------------

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TV/CD, PORT COAXIAL1, COAXIAL2, OPTICAL1, OPTICAL2: Select a corresponding digital audio input to which the component has been connected. - - - - -: Select if the component is connected to an analog audio input.
Note When an HDMI IN is assigned to an input selector in HDMI Input ( page 43), the same HDMI IN will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the selection in the Audio Selector ( page 53). Available sampling rates for PCM signals from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16, 20, 24 bit. If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the PORT selector. The TUNER selector cannot be assigned and is fixed at the - - - - - option.

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TV/CD, PORT IN1, IN2: Select a corresponding component video input to which the video component has been connected. - - - - -: Select if you are using the HDMI output, not the component video output, to output composite video and component video sources.
Note If you connect a component (such as UP-A1 Dock with docked iPod/iPhone) to the UNIVERSAL PORT jack, you cannot assign any input to the PORT selector. The TUNER selector cannot be assigned and is fixed at the - - - - - option.

Speaker Setup
Main menu Speaker Setup

Some of the settings in this section are set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 31). Here you can check the settings made by Audyssey 2EQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey 2EQ Room Correction and Speaker Setup function.
Note These settings are not available in either of the following cases: a pair of headphones is connected. the Audio TV Out setting is set to On ( page 56). HDMI Control (RIHD) is set to On ( page 56) and youre listening through your TV speakers.

Digital Audio Input

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the OPTICAL IN 1, you must assign OPTICAL1 to the TV/CD input selector. Here are the default assignments.
Input selector BD/DVD VCR/DVR CBL/SAT GAME PC AUX TV/CD PORT Default assignment COAXIAL1 ----COAXIAL2 OPTICAL1 --------OPTICAL2 -----

Speaker Settings
If you change these settings, you must run Audyssey 2EQ Room Correction and Speaker Setup again ( page 31). If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you bi-amp the front speakers, you must change the Speakers Type (Front) setting ( page 45). For hookup information, see Bi-amping the Front Speakers ( page 15).
Note When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room. Before you change these settings, turn down the volume.

En

44

 Speaker Impedance (Australian models) 4ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6ohms: Select if the impedances of all speakers are between 6 and 16 ohms.
Note (North American models) Speakers with an impedance of less than 6 ohms are not supported.

Center*1, Surround*1, Surround Back*2*3*4*5 Full Band 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz None Front High*1*2*4*6 Full Band 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz None
Note
*1 *2 *3 *4

Speakers Type (Front) Normal: Select this if youve connected your front speakers normally. Bi-Amp: Select this if youve bi-amped your front speakers. Powered Zone 2 No Yes: Zone 2 speakers can be used. (Powered Zone 2 enabled).
Note If the Speakers Type (Front) setting is set to Bi-Amp, Powered Zone 2 cannot be used. When the Powered Zone 2 setting is set to Yes, the surround back or front high speakers cannot be used.

*5 *6

Full Band can be selected only when Full Band is selected in the Front setting. If the Surround setting is set to None, this setting cannot be selected. If the Surround setting is set to anything other than Full Band, Full Band cannot be selected here. If the Speakers Type (Front) setting is set to Bi-Amp, or the Powered Zone 2 setting is set to Yes, this setting cannot be selected. If anything else than None is selected in Front High, this setting is automatically set to None. If anything else than None is selected in Surround Back, this setting is automatically set to None.

Speaker Configuration
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify Full Band for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speakers manuals to determine the optimum crossover frequencies. If you set up your speakers using Audyssey 2EQ Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to 80Hz(THX) crossover.
Note These settings are not available in either of the following cases: a pair of headphones is connected. the Audio TV Out setting is set to On ( page 56). HDMI Control (RIHD) is set to On ( page 56) and youre listening through your TV speakers.

Surround Back Ch 1ch: Select if only one surround back speaker L is connected. 2ch: Select if two (left and right) surround back speakers are connected.
Note If the Surround Back Setting is set to None, this setting cannot be selected.

LPF of LFE (Low-Pass Filter for the LFE Channel) 80Hz, 90Hz, 100Hz, 110Hz, 120Hz Bypass: Low-Pass Filter is not applied. With this setting, you can specify the cutoff frequency of the LFE channels low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.
Note If youre using THX-certified speakers, select 80Hz.

Double Bass This setting is NOT set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 31). On Off(THX) Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.
Note This function can be set only if the Subwoofer setting is set to Yes, and the Front setting is set to Full Band. If youre using THX-certified speakers, select Off(THX).

Subwoofer Yes No Front Full Band 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note If the Subwoofer setting is set to No, the Front setting is fixed at Full Band.

En

45

 Wireless Front High, Wireless Surround Back, Wireless Subwoofer When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the speaker setting menu may appear on screen. Yes: The audio is output from the speakers connected to the wireless unit. No: The audio is not output from the speakers connected to the wireless unit. When the wireless unit is connected to the UNIVERSAL PORT jack on the AV receiver, you can select if you wish to output the audio from the speakers connected to the wireless unit.
Note If the Front High setting is set to None ( page 45), Wireless Front High cannot be selected. If the Surround Back setting is set to None ( page 45), Wireless Surround Back setting cannot be selected. If the Subwoofer setting is set to No ( page 45), Wireless Subwoofer setting cannot be selected.

Level Calibration
This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 31). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Left, Front High Left, Center*1, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left 12dB to 0dB to +12dB in 1 dB step. Subwoofer*1 15dB to 0dB to +12dB in 1 dB step.
Note These settings cannot be calibrated in either of the following cases: a pair of headphones is connected. the Audio TV Out setting is set to On ( page 56). HDMI Control (RIHD) is set to On ( page 56) and youre listening through your TV speakers. the AV receiver is muted. Speakers that you set to No or None in the Speaker Configuration cannot be selected ( page 45). The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder. *1 For the center speaker and subwoofer, the level settings made by using the Home menu are saved in this menu ( page 40). Tip If youre using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

Speaker Distance
This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup ( page 31). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listeners ears as the sound designer intended. Unit feet: Distances can be set in feet. Range: 0.2ft to 30.0ft in 0.2 foot steps. meters: Distances can be set in meters. Range: 0.06m to 9.00m in 0.06 meter steps. (The default setting varies from country to country.) Left, Front High Left, Center, Front High Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer Specify the distance from each speaker to your listening position.
Note These settings are not available in either of the following cases: a pair of headphones is connected. the Audio TV Out setting is set to On ( page 56). HDMI Control (RIHD) is set to On ( page 56) and youre listening through your TV speakers. Speakers that you set to No or None in the Speaker Configuration cannot be selected ( page 45).

Equalizer Settings
With the Equalizer settings, you can adjust the tone of speakers individually with a 5-band equalizer. The volume of each speaker can be set ( page 46). Equalizer Manual: You can adjust the equalizer for each speaker manually. Continue with the following procedure:

1 2

Press w to select Channel, and then use e/r to select a speaker. Use q/w to select a frequency, and then use the e/r to adjust the level at that frequency. The volume at each frequency can be adjusted from +6dB to 0dB to +6dB in 1 dB steps.
Tip Low frequencies (e.g., 63Hz) affect bass sounds; high frequencies (e.g., 16000Hz) affect treble sounds.

En

46

Use q to select Channel, and then use e/r to select another speaker. Repeat steps 1 and 2 for each speaker. You cannot select speakers that you set to No or None in the Speaker Configuration ( page 45).

Off: Tone off, response flat.

Note You can select: 63Hz, 250Hz, 1000Hz, 4000Hz, or 16000Hz. And for the subwoofer, 25Hz, 40Hz, 63Hz, 100Hz, or 160Hz. When the Direct listening mode is selected, the equalizer settings have no effect. If Audyssey is enabled, it prevails over this setting ( page 49).

Loudness Plus Off On When the Loudness Plus is set to On, it is possible to enjoy even subtle nuances of audio expression at low volume. This is only available when the THX listening mode is selected. Preserve THX Settings Yes No If this setting is set to Yes, Dynamic EQ and Dynamic Volume have no effect in THX listening mode.
Note This setting is fixed at Yes if Loudness Plus is set to On.

THX Audio Setup

Surr Back Speaker Spacing < 1ft (< 0.3m) 1 ft - 4 ft (0.3 m - 1.2 m) > 4ft (> 1.2m) You can specify the distance between your surround back speakers.
Note Cannot be set if: Surround Back Ch is set to 1ch ( page 45). Speakers Type (Front) is set to Bi-Amp ( page 45). Surround Back is set to None ( page 45). Powered Zone 2 is set to Yes ( page 45) and Zone 2 turned on ( page 61).

THX Ultra2/Select2 Subwoofer No Yes If youre using a THX-certified subwoofer, set this setting to Yes.
Note If the Subwoofer setting is set to No, this setting cannot be selected ( page 45).

THX Loudness Plus THX Loudness Plus is a new volume control technology featured in THX Ultra2 Plus and THX Select2 Plus Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that certain sound elements can be lost or perceived differently by the listener. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume is reduced by intelligently adjusting ambient surround channel levels and frequency response. This enables users experience the true impact of soundtracks regardless of the volume setting. THX Loudness Plus is automatically applied when listening in any THX listening mode. The new THX Cinema, THX Music, and THX Games modes are tailored to apply the proper THX Loudness Plus settings for each type of content.

BGC Off On You can apply THXs Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequencies for listeners sitting very close to a room boundary (i.e., wall).
Note This setting is only available if THX Ultra2/Select2 Subwoofer is set to Yes. If the Subwoofer setting is set to No, this setting cannot be selected ( page 45).

En

47

Audio Adjust
Main menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono
Multiplex Input Channel Main Sub Main/Sub This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on. Mono Input Channel Left + Right Left Right This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode. Output Speaker Center: Mono audio is output by the center speaker. Left / Right: Mono audio is output by the front left and right speakers. This setting determines which speakers output mono audio when the Mono listening mode is selected.
Note If the Center setting is set to None ( page 45), this setting cannot be selected.

Dimension 3 to 0 to +3 With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic IIx Music listening mode. Higher settings move the sound field backward. Lower settings move it forward. If the stereo image feels too wide, or theres too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like its in mono, or theres not enough surround sound, move it backward. Center Width 0 to 3 to 7 With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic IIx Music listening mode. Normally, if youre using a center speaker, the center channel sound is output from only the center speaker. (If youre not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound. PL IIz Height Gain Low Mid High The Height Gain Control in Dolby Pro Logic IIz enables the listener to select how much gain is applied to the front high speakers. There are three settings, Low, Mid and High, and the front high speakers are accentuated in that order. While Mid is the default listening setting, the listener may adjust the Height Gain Control to their personal preference.
Note If the Front High settings is set to None ( page 45), this setting cannot be selected.

Dolby EX Dolby EX Auto: If the source signal contains a Dolby EX flag, the Dolby EX or THX Surround EX listening mode is used. Manual: You can select any available listening mode. This setting determines how Dolby EX encoded signals are handled. This setting is unavailable if no surround back speakers are connected. This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only.
Note If the Surround Back setting is set to None ( page 45), this setting cannot be selected. If the Front High setting is enabled ( page 45), this setting is fixed at Manual.

Dolby
PL IIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If youre not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx. Panorama On Off With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode.

En

48

DTS
Neo:6 Music Center Image 0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Changing the value from 0 to 5 will spread the sound of the center channel to left and right (outwards).

Source Setup
Items can be set individually for each input selector. Preparation Press the input selector buttons to select an input source.
Main menu Source Setup

Audyssey
The tone for each speaker is set automatically by Audyssey 2EQ Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup ( page 31). Audyssey Off Movie: Select this setting for movie material. The Audyssey indicator lights. Music: Select this setting for music material. The Audyssey indicator lights.
Note If the Audyssey setting is set to Off, the Equalizer settings are applied ( page 46). When Audyssey Quick Start has been used for measurement, the Audysseysetting cannot be selected. Audyssey equalizing does not work with DSD sources. These technologies cannot be used when: a pair of headphones is connected, or Direct listening mode is selected.

Audyssey DSX
Soundstage 3dB to Reference to +3dB With this setting, you can adjust the sound stage when using Audyssey DSX.
Note This listening mode can be selected only when all the following conditions are satisfied: The center speaker is connected. The front high speakers are connected.

Theater-Dimensional
Listening Angle Wide: Select if the listening angle is 40 degrees. Narrow: Select if the listening angle is 20 degrees. With this setting, you can optimize the TheaterDimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.
Front left speaker Front right speaker
20/40

LFE Level
Dolby Digital*1, DTS*2, Multich PCM, Dolby TrueHD, DTS-HD Master Audio, DSD*3 QdB, 20dB, 10dB, or 0dB With these settings, you can set the level of the LFE (Low Frequency Effects) channel individually for each input sources. If you find that low-frequency effects are too loud when using one of these sources, change the setting to 20 dB or Q dB.
*1 *2 *3

Dynamic EQ Off On: Audyssey Dynamic EQ becomes active. The Dynamic EQ indicator lights. With Audyssey Dynamic EQ, you can enjoy great sound even when listening at low volume levels. Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. It does so by selecting the correct frequency response and surround volume levels moment-by-moment so that the content sounds the way it was created at any volume level not just at reference level.
Note These technologies cannot be used when: a pair of headphones is connected, or Direct listening mode is selected.

Dolby Digital and Dolby Digital Plus sources DTS and DTS-HD High Resolution sources DSD (Super Audio CD) sources

En

49

 Reference Level Audyssey Dynamic EQ Reference Level Offset 0dB: This should be used when listening to movies. 5dB: Select this setting for content that has a very wide dynamic range, such as classical music. 10dB: Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference. 15dB: Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range. Movies are mixed in rooms calibrated for film reference. To achieve the same reference level in a home theater system each speaker level must be adjusted so that 30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey 2EQ will play at reference level when the master volume control is set to the 0 dB position. At that level you can hear the mix as the mixers heard it. Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other nonfilm content. Audyssey Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard.
Note If Dynamic EQ setting is set to Off, these technologies cannot be used.

Note If you want to use Audyssey Dynamic EQ or Dynamic Volume with THX listening modes, set the Loudness Plus setting to Off and set Preserve THX Settings to No ( page 47). If you make Dynamic Volume active, Dynamic EQ is set to On. The Dynamic Vol indicator will light. When Dynamic EQ is set to Off, Dynamic Volume is automatically switched to Off. These technologies cannot be used when: a pair of headphones is connected, or Direct listening mode is selected.

About Audyssey Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works well by itself. However, if Audyssey 2EQ is on, the two technologies work in tandem to provide well-balanced sound for every listener at any volume level. About Audyssey Dynamic Volume Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic Volume works fine by itself, but can also be used with Audyssey Dynamic EQ. When both are on, Audyssey Dynamic EQ adjusts the perceived bass response, tonal balance, surround impression, and dialog clarity whether watching movies, flipping between television channels, or changing from stereo to surround sound content, when Dynamic Volume adjusts the volume.

Dynamic Volume Off Light: Activates Light Compression Mode. Medium: Activates Medium Compression Mode. Heavy: Activates Heavy Compression Mode. This setting affects volume the most. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard.

En

50

IntelliVolume
IntelliVolume 12dB to 0dB to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others. Use e/r to set the level. If a component is noticeably louder than the others, use e to reduce its input level. If its noticeably quieter, use r to increase its input level.
Note IntelliVolume does not work for Zone 2.

Name input area

4 - 4. Name Edit
Name

BD/DVD

a n 1 {

b o 2 }

c p

d q

e r 5

f s 6 <

g t 7 >

h u

i v

j w

k x

l y

m z

3 4 | : Shift
Shift

8 9 0 ? Space OK Back Space

CLR

+10

All Erase

A N ! [

B O @ ]

C P #

D Q $ ;

E R %

F S ^ ,

G T & .

H U

Shift
+10

K L X Y _ / Space Back Space OK

CLR

I V (

J W )

M Z ~

A/V Sync
A/V Sync 0ms to 800ms in 5 ms steps. When using progressive scanning on your Blu-ray Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. To view the TV picture while setting the delay, press Enter. To return to the previous screen, press Return. The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the Lip Sync setting is set to On or not ( page 57).
Note A/V Sync is disabled when the Direct listening mode is used with an analog input source. This setting cannot be used with the NET input selector.

Shift

All Erase

Space: Enter a space character. Shift*1: Toggles between lower and upper case characters. (Left)/ (Right): Moves the cursor left or right in the Name input area. Back Space*2: Moves the cursor backward and deletes one character. OK: Confirms your entry.
Tip
*1 *2

This can also be performed by using +10 on the remote controller. Press CLR on the remote controller to delete all the characters you have input.

Name Edit
You can enter a custom name for each individual input selector and radio preset for easy identification. When entered, the custom name will appear on the display. The custom name is edited using the character input screen. Name To correct a character:

1 2 3
Tip

Use q/w/e/r to select (Left) or (Right), and then press Enter. Press Enter several times to highlight the incorrect character (For each pressure, the cursor is moved on the next character). Use q/w/e/r to select the correct character, and then press Enter.

1 2

Use q/w/e/r to select a character, and then press Enter. Repeat this step to enter up to 10 characters. To store a name when youre done, be sure to select OK by using q/w/e/r, and then press Enter.

To name a radio preset, use Tuner to select AM or FM, and then select the preset ( page 28). To restore a custom name to its default, erase the custom name by entering an empty white space for each letter. Note This setting cannot be used for the NET and USB input selector.

En

51

Picture Adjust
Using Picture Adjust, you can adjust the picture quality and reduce any noise appearing on the screen. To view the TV picture while setting, press Enter. To return to the previous screen, press Return. Wide Mode*1*2 This setting determines the aspect ratio. 4:3:

Game Mode*3*4*5 Off On If video signal delay occurs during playback on a video component (i.e., game console), select the corresponding input source and set the Game Mode setting to On. The delay will decrease but in return the picture quality will become poor. Film Mode*3*5*6 Video: Film Mode detection is not applied and the input signal is handled as a video source. Auto: Detects whether the input signal is a video or a movie. If it is a movie, the appropriate conversion is applied. The AV receiver will adjust to the picture source, automatically converting it to the appropriate progressive signal and reproducing the natural quality of the original picture. Edge Enhancement*3*5*6*7 Off Low Mid High With Edge Enhancement, you can make the picture appear sharper. Noise Reduction*3*5*6*7 Off Low Mid High With this setting, you can reduce noise appearing on the screen. Select the desired level. Brightness*1*3*5 50 to 0 to +50 With this setting you can adjust the picture brightness. 50 is the darkest. +50 is the brightest. Contrast*1*3*5 50 to 0 to +50 With this setting you can adjust contrast. 50 is the least. +50 is the greatest. Hue*1*3*5 50 to 0 to +50 With this setting you can adjust the red/green balance. 50 is the strongest green. +50 is the strongest red. Saturation*1*3*5 50 to 0 to +50 With this setting you can adjust saturation. 50 is the weakest color. +50 is the strongest color.

Full:

Zoom:

Wide Zoom:

Auto: According to the input signals and monitor output setting, the AV receiver automatically selects the 4 : 3, Full, Zoom or Wide Zoom mode. See Monitor Out for details on the monitor output setting ( page 43). Picture Mode*1 Custom: All settings can be performed manually. Cinema: Select when the picture source is a movie or alike. Game: Select when the video source is a game console. Through: Does not adjust picture quality (changes resolution). Direct: Does not adjust picture quality (does not change resolution). When video is output from HDMI OUT, it is processed the same as Through. With Picture Mode, you can change the following settings to be suitable for the movie or game screen by one operation; Game Mode, Film Mode, Edge Enhancement, Noise Reduction, Brightness, Contrast, Hue, Saturation or Color Temperature.

En

52

 Color Temperature*3*5 Warm Normal Cool With this setting you can adjust the color temperature.
Note Picture Adjust cannot be used with the NET input selectors. *1 This procedure can also be performed on the remote controller by using the Home menu ( page 40). *2 When a 3D video source is input, Wide Mode is fixed to Full. *3 When the Picture Mode setting is set to anything other than Custom, this setting cannot be used. *4 If the Resolution setting is set to 4K Upscaling ( page 43), this setting is fixed at Off. *5 Press CLR if you want to reset to the default value. *6 If you are using the analog RGB input, this setting is not available. *7 If the Game Mode setting is set to On, this setting is fixed at Off.

Audio Selector
You can set priorities of audio output when there are both digital and analog inputs. Audio Selector ARC: The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver.*1 With this selection, the TVs audio can be automatically selected as a priority among other assignments. HDMI: This can be selected when HDMI IN has been assigned as an input source. If both HDMI (HDMI IN) and digital audio inputs (COAXIAL IN or OPTICAL IN) have been assigned, HDMI input is automatically selected as a priority. COAXIAL: This can be selected when COAXIAL IN has been assigned as an input source. If both coaxial and HDMI inputs have been assigned, coaxial input is automatically selected as a priority. OPTICAL: This can be selected when OPTICAL IN has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority. Analog: The AV receiver always outputs analog signals.
Note The setting is stored individually for each input selector. This setting can be made only for the input source that is assigned as HDMI IN, COAXIAL IN, or OPTICAL IN. The Audio Selector settings cannot be used with the NET, USB and Port (with connected component) input selectors. *1 You can select ARC if you select the TV/CD input selector. But you cannot if youve selected Off in the Audio Return Channel setting ( page 57).

Fixed Mode Off: The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead. PCM: Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the PCM indicator will flash and noise may also be produced. DTS: Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. When HDMI, COAXIAL or OPTICAL is selected in the Audio Selector setting, you can then specify the signal type in Fixed Mode. Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS. If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM. If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.
Note The setting is stored individually for each input selector. The setting will be reset to Off when you change the setting in Audio Selector ( page 53).

Charge Mode
Charge Mode Auto: Power feeding is interrupted when your iPod/iPhone is fully charged. On: Power feeding continues even if your iPod/iPhone is fully charged. Off: Your iPod/iPhone is not charged. You can specify how the power is fed to your iPod/iPhone when the AV receiver is in standby mode.
Note This setting cannot be selected when: the UP-A1 Dock with docked iPod/iPhone is not connected to the AV receiver, or the docked iPod/iPhone model is not supported. When the Charge Mode setting is set to On, or to Auto with your iPod/iPhone recharging, the SLEEP indicator is dimly lit in standby mode. In such conditions, the power consumption of the AV receiver slightly increases.

En

53

Listening Mode Preset

You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals. You can select other listening modes during playback, but the mode specified here will be resumed once the AV receiver has been set to standby.
Main menu Listening Mode Preset

DTS/DTS-ES/DTS-HD With this setting, you can specify the listening mode used when DTS or DTS-HD High Resolution format digital audio signals are played (DVD, LD, CD, etc.). Specifies the default listening mode for DTS-HD Master Audio sources, such as Blu-ray or HD DVD (input via HDMI). Other Multich Source Specifies the default listening mode for multichannel PCM sources from HDMI IN such as DVD-Audio, and DSD multichannel sources such as Super Audio CD.

Use q/w to select the input source that you want to set, and then press Enter. The following menu appears.
5. Listening Mode Preset 1. 2. 3. 4. 5. 6. BD/DVD VCR/DVR CBL/SAT GAME PC AUX

Miscellaneous
Main menu Miscellaneous

Volume Setup
Volume Display Absolute: Displayed range is Min, 1 to 99, Max. Relative (THX): Displayed range is QdB, 81dB to +18dB. With this setting, you can choose how the volume level is displayed. The absolute value 82 is equivalent to the relative value 0 dB.
Note If the absolute value is set to 82, 82Ref will appear on the display and the THX indicator will flash.

Use q/w to select the signal format that you want to set, and then use e/r to select a listening mode. Only listening modes that can be used with each input signal format can be selected ( pages 35 to 39). The Last Valid option means that the listening mode selected last will be used.
Note If you connect an input component (such as UP-A1 series Dock that seated iPod) to the UNIVERSAL PORT jack, the only listening modes you can assign to the PORT selector are specific to analog sound. For the Tuner input selector, only Analog will be available. For the NET or USB input selector, only Digital will be available.

Analog / PCM / Digital With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellite, etc.) or PCM digital (CD, DVD, etc.) audio signal is played.
Note For the AUX input selector, only PCM is available.

Muting Level QdB (fully muted), 50dB to 10dB in 10 dB steps. This setting determines how much the output is muted when the muting function is used ( page 41). Maximum Volume Off, 50 to 99 (Absolute display) Off, 32dB to +17dB (Relative display) With this setting, you can limit the maximum volume. To disable this setting, select Off. Power On Volume Last, Min, 1 to 99 or Max (Absolute display) Last, QdB, 81dB to +18dB (Relative display) With this preference, you can specify the volume setting to be used each time the AV receiver is turned on. To use the same volume level that was used when the AV receiver was turned off, select Last. The Power On Volume cannot be set higher than the Maximum Volume setting. Headphone Level 12dB to 0dB to +12dB With this preference, you can specify the headphone volume relative to the main volume. This is useful if theres a volume difference between your speakers and your headphones.

Mono/Multiplex Source With this setting, you can specify the listening mode used when a mono digital audio signal is played (DVD, etc.). 2ch Source With this setting, you can specify the listening mode used when 2-channel (2/0) stereo digital sources, such as Dolby Digital or DTS, are played. Dolby D/Dolby D Plus/TrueHD With this setting, you can specify the listening mode used when Dolby Digital or Dolby Digital Plus format digital audio signals are played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI).

En

54

OSD Setup
On Screen Display On Off This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when On is selected, operation details may not be output if the input source is connected to an HDMI IN. Language (North American models) English, Deutsch, Franais, Espaol, Italiano, Nederlands, Svenska (Australian models) English, Deutsch, Franais, Espaol, Italiano, Nederlands, Svenska, This setting determines the language used for the onscreen setup menus.

Hardware Setup
Main menu Hardware Setup

Remote ID
Remote ID 1, 2, or 3 When several Integra/Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from the other components, you can change its remote ID from 1, to 2 or 3.
Note If you do change the AV receivers remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you wont be able to control it with the remote controller.

Changing the remote controllers ID

12V Trigger A/B/C Setup

When several components are turned on simultaneously by using triggers A, B, and C, depending on the type of components, a large amount of current may be drawn momentarily. To prevent this, you can delay trigger signals A, B, and C individually. Another application of trigger delay is eliminating the "thump" noise thats sometimes heard when a source component is turned on. You can accomplish this by delaying the trigger signal for your power amplifier, so that it's the last component to be turned on. Delay 0sec, 1sec, 2sec, 3sec When 0sec is selected, the trigger signal is output as soon as the input source is changed.
Note By default, the 12V Trigger A Setup menu is set to 0sec, those on the 12V Trigger B Setup menu is set to 1sec, and those on the 12V Trigger C Setup menu is set to 2sec. Use a miniplug cable to connect the AV receiver's 12V TRIGGER OUT A, B, or C jack to the 12 V trigger input on a connected component.

1 2

While holding down Receiver, press and hold down Setup until the remote indicator lights (about 3 seconds) ( page 42). Use the number buttons to enter ID 1, 2, or 3. The remote indicator flashes twice.

Multi Zone
Zone 2 Out If youve connected your Zone 2 speakers to an amp with no volume control, set the Zone 2 Out setting, respectively, to Variable so that you can set the zones volume, balance, and tone on the AV receiver. Fixed: The Zone 2 volume must be set on the amp in that zone. Variable: The Zone 2 volume can be set on the AV receiver. Zone 2 Maximum Volume Off, 50 to 99 (Absolute display) Off, 32dB to +17dB (Relative display) With this setting, you can limit the maximum volume. To disable this setting, select Off. Zone 2 Power On Volume Last, Min, 1 to 99 or Max (Absolute display) Last, QdB, 81dB to +18dB (Relative display) With this preference, you can specify the volume setting to be used each time the AV receiver is turned on. To use the same volume level that was used when the AV receiver was turned off, select Last. The Zone 2 Power On Volume cannot be set higher than the Zone 2 Maximum Volume setting.

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TUNER, TV/CD, PORT, NET, USB Off: No trigger signal is output. A 12-volt trigger signal is output when the connected component is selected as the source for: Main: Main room. Zone 2: Zone 2. Main/Zone 2: Main room or Zone 2.
Note By default, all input sources on the 12V Trigger A Setup menu are set to Main, those on the 12V Trigger B Setup menu are set to Main/Zone 2, and those on the 12V Trigger C Setup menu are set to Zone 2

En

55

Tuner
For AM/FM tuning to work properly, you must specify the AM/FM frequency step used in your area. Note that when this setting is changed, all radio presets will be deleted. AM/FM Frequency Step (North American models) 10kHz/200kHz: 9kHz/50kHz: Select the frequency step according to your area. AM Frequency Step (Australian models) 10kHz: 9kHz: Select the frequency step according to your area.

HDMI
HDMI Control (RIHD) Off On Turn this setting on to allow p-compatible components connected via HDMI to be controlled by the AV receiver ( page 85).
Note When the setting is set to On and the menu is closed, the names of connected p-compatible components and RIHD On are displayed on the AV receiver. Search (name) RIHD On When the AV receiver cannot receive the name of the component, it is displayed as Player* or Recorder*, etc (* shows up and indicates the number of components, when two or more are received). When an p-compatible component is connected to the AV receiver via an HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray Disc/DVD player (being powered on) with the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player will be displayed on the AV receiver. Set it to Off when a connected piece of equipment is not compatible or it is unclear whether the equipment is compatible or not. If operation is not normal when set to On, change the setting to Off. Refer to the connected components instruction manual for details. When HDMI Control (RIHD) setting is set to On, the power consumption on standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

HDMI Through Off Auto: Detects the signal and automatically selects the input source. BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TV/CD, PORT: Selects the input source for which the HDMI Through function is enabled. Last: The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode. When enabling the HDMI Through function, regardless of whether the AV receiver is on or in standby, both audio and video streams from an HDMI input will be output to the TV or other components via HDMI connection. The HDMI indicator light when enabled (HDMI is dimly-lit). This setting is set to Auto automatically when the above HDMI Control (RIHD) is set to On.
Note Only the input source assigned to the HDMI IN via HDMI Input is enabled ( page 43). The power consumption during standby mode will increase during the HDMI Through function; however in the following cases, the power consumption can be saved: The TV is in standby mode. You are watching a TV program. Refer to the connected components instruction manual for details. Depending on the connected component, the correct input source may not be selected with the setting set to Auto. This setting is set to Off automatically when the HDMI Control (RIHD) setting is set to Off.

Audio TV Out Off On This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the HDMI output and you want to listen to the audio from a connected component through your TVs speakers. Normally, this should be set to Off.
Note If On is selected and the audio can be output from the TV, the AV receiver will output no sound through its speakers. In this case, TV Speaker appears on the display by pressing Display. When HDMI Control (RIHD) is set to On, this setting is fixed to Auto. With some TVs and input signals, no sound may be output even when this setting is set to On. When Audio TV Out or HDMI Control (RIHD) is set to On and youre listening through your TVs speakers ( page 17), turning up the AV receivers volume control will make the sound be output from the AV receivers front left and right speakers. To stop the AV receivers speakers producing sound, change the settings, change your TVs settings, or turn down the AV receivers volume.

En

56

 Audio Return Channel Off Auto: The audio signal from your TV tuner can be sent to the HDMI OUT of the AV receiver. The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to the HDMI OUT of the AV receiver. To use this function, you must select the TV/CD input selector and your TV must be ARC capable.
Note If you set Audio Return Channel to Auto, the Audio Selector settings of the TV/CD input selector will be automatically switched to ARC ( page 53). The Audio Return Channel setting can be set only when the HDMI Control (RIHD) setting is set to On. This setting is set to Auto automatically when the HDMI Control (RIHD) is set to On for the first time.

Network
After modifying the network settings, you must confirm the changes by executing Save. This section explains how to configure the AV receivers network settings manually. If your routers DHCP server is enabled, you dont need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e., DHCP is set to Enable). If, however, your routers DHCP server is disabled (youre for example using static IP), youll need to configure these settings yourself, in which case, a knowledge of Ethernet networking is essential. Whats DHCP? DHCP (Dynamic Host Configuration Protocol) is used by routers, computers, the AV receiver, and other devices to automatically configure themselves on a network. Whats DNS? The DNS (Domain Name System) translates domain names into IP addresses. For example, when you enter a domain name such as www.onkyousa.com in your Web browser, before accessing the site, your browser uses DNS to translate this into an IP address, in this case 63.148.251.142. MAC Address This is the AV receivers MAC (Media Access Control) address. This address cannot be changed. DHCP Enable Disable This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address, Subnet Mask, Gateway, and DNS Server settings.
Note If you select Disable, you must configure the IP Address, Subnet Mask, Gateway, and DNS Server settings yourself.

Lip Sync Off On This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.
Note This function works only if your HDMI-compatible TV supports HDMI Lip Sync.

After changing the settings of the HDMI Control (RIHD), HDMI Through or Audio Return Channel turn off the power on all connected pieces of equipment and then turn them on again. Refer to the users manuals for all connected pieces of equipment.

Auto Standby
Auto Standby Off On When Auto Standby is set to On, the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input. Auto Standby will appear on the display and OSD 30 seconds before the Auto Standby comes on. Default setting: On (Australian models), Off (North American models)
Note Set to On, the Auto Standby function may activate itself during playback with some sources. The Auto Standby function does not work when Zone 2 is on.

IP Address Class A: 10.0.0.0 to 10.255.255.255 Class B: 172.16.0.0 to 172.31.255.255 Class C: 192.168.0.0 to 192.168.255.255 Enter a static IP address provided by your ISP. Most routers use Class C IP addresses. Subnet Mask Enter the subnet mask address provided by your ISP (typically 255.255.255.0). Gateway Enter the gateway address provided by your ISP. DNS Server Enter the DNS server address provided by your ISP.

En

57

 Proxy URL To use a Web proxy, enter its URL here. Proxy Port If youre using a Web proxy, enter a proxy port number here. Network Control Enable Disable This setting enables or disables control over the network.
Note When set to Enable, the NET indicator is dimly-lit and the power consumption slightly increases in standby mode.

Remote Controller Setup

Main menu Remote Controller Setup

Remote Mode Setup

See Looking up for Remote Control Code ( page 67).

Lock Setup
With this preference, you can protect your settings by locking the setup menus.
Main menu Lock Setup

Control Port 49152 to 65535 This is the network port used for control over the network.
Note When the Network Control setting is set to Disable, this setting is cannot be selected.

Setup Locked Unlocked When Locked is selected, the setup menus will be locked and you cannot change any setting.

Firmware Update
See Firmware Update for the update procedure ( page 79).
Note Perform the firmware update only when such an announcement is posted on the Integra web site. Visit the Integra web site for the latest information. It takes maximum 60 minutes to complete the firmware update.

Using the Audio Settings

You can change various audio settings from the Home menu ( page 40).

1 2

Press Receiver followed by Home. Use q/w and Enter to select Audio, and then use q/w/e/r to make the desired selection.

Version Displays the current version of the firmware. Receiver via NET: Performs the firmware update via Internet. Check the network connection before updating. via USB: Performs the firmware update from a USB device. These settings allow you to update the AV receivers firmware. Do not shutdown the power of the AV receiver while updating. Universal Port via NET: Performs the firmware update via Internet. Check the network connection before updating. via USB: Performs the firmware update from a USB device. These settings allow you to update Onkyo docks firmware. Do not shutdown the power of the AV receiver while updating.
Note This update shall not be performed when no dock is connected to the UNIVERSAL PORT jack.

Note These settings are not available in either of the following cases: a pair of headphones is connected. the Audio TV Out setting is set to On ( page 56). HDMI Control (RIHD) is set to On ( page 56) and youre listening through your TV speakers.

Tone Control Settings

Bass 10dB to 0dB to +10dB in 2 dB steps. You can boost or cut low-frequency sounds output from the front speakers. Treble 10dB to 0dB to +10dB in 2 dB steps. You can boost or cut high-frequency sounds output from the front speakers. You can adjust the bass and treble for the front speakers, except when the Direct or THX listening mode is selected. Operating on the AV receiver

1 2
Note

Press Tone repeatedly to select either Bass or Treble. Use + and to adjust.

En

58

To bypass the bass and treble tone circuits, select the Direct or THX listening mode.

Speaker Levels
Subwoofer Level 15dB to 0dB to +12dB in 1 dB steps. Center Level 12dB to 0dB to +12dB in 1 dB steps. You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to Level Calibration ( page 46) before setting the AV receiver to standby.
Note You cannot use this function while the AV receiver is muted. Speakers that are set to No or None in Speaker Configuration ( page 45) cannot be adjusted.

Note The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options. The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD. The Late Night function is set to Off when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to Auto.

Music Optimizer
Music Optimizer Off On Turn this setting on to enhance the sound quality of compressed music files. Use it with music files that use lossy compression, such as MP3.
Note The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals. The Music Optimizer is disabled when the Direct listening mode is selected. The setting is stored individually for each input selector. The M.Opt indicator will light ( page 9).

Audyssey
Audyssey See Audyssey in Source Setup ( page 49). Dynamic EQ See Dynamic EQ in Source Setup ( page 49). Dynamic Volume See Dynamic Volume in Source Setup ( page 50).
Note These technologies can be used when all the following conditions are met: Room Correction and Speaker Setup is completed. Note that Audyssey requires the Audyssey 2EQ Full Calibration method. Any listening mode other than Direct is selected. A pair of headphones is not connected. The setting is stored individually for each input selector.

Re-EQ
With the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. Re-EQ Off On This function can be used with the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Multichannel, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS Express, DSD, Dolby EX, Dolby Pro Logic IIz Height, Dolby PLIIx Movie, Neo:6 Cinema and 5.1-channel source + Neo:6. Re-EQ(THX) Off On This function can be used with the following listening modes: THX Cinema, THX Surround EX, and THX Select2 Cinema.
Note Settings for the Re-EQ function are kept in each listening mode. In THX listening mode however, the setting will return to On when the AV receiver is turned off.

Late Night
Late Night For Dolby Digital and Dolby Digital Plus sources, the options are: Off Low: Small reduction in dynamic range. High: Large reduction in dynamic range. For Dolby TrueHD sources, the options are: Auto: The Late Night function is set to On or Off automatically. Off On Turn this setting on to reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levelsideal for watching movies late at night when you dont want to disturb anyone.

En

59

Zone 2
In addition to the main listening room, you can also enjoy playback in another room, which we call Zone 2. For either of the rooms, you can specify a different input source.

Making Zone 2 Connections

There are two ways you can connect Zone 2 speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an amp in Zone 2.

Connecting the Zone Speakers to an Additional Amplifier

This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2.
Main room

Connecting Your Zone 2 Speakers Directly to the AV receiver

This setup allows 5.1-channel playback in your main room and 2-channel stereo playback in Zone 2, with a different source in each room. This is called Powered Zone 2, as the Zone 2 speakers are powered by the AV receiver. To use this setup, you must set the Powered Zone 2 setting to Yes ( page 45).
Main room TV

TV

AV receiver

Zone 2
IN

AV receiver

Receiver/ integrated amp

Note With the default settings, the Zone 2 volume must be set on the Zone 2 amp. If your Zone 2 amp has no volume control, set the Zone 2 Out setting to Variable so that you can set the Zone 2 volume on the AV receiver.

Setting the Zone 2 Out

R L

See Multi Zone ( page 55).

Zone 2

Note With this setup, the volume of Zone 2 is controlled by the AV receiver. Powered Zone 2 cannot be used if Speakers Type (Front) is set to Bi-Amp ( page 45).

En

60

Controlling Zone 2 Components

Operating on the AV receiver
Zone 2 Off Tone +, Input selector buttons

Adjusting the Volume for Zone 2

Operating on the remote controller

1 2 1

Press Zone2. Use VOL q/w to adjust the volume.

Operating on the AV receiver Use Zone 2 Level q/w.

Zone 2 Level q/w

Muting Zone 2
Operating on the remote controller

To turn on Zone 2 and select an input source, press Zone 2 followed by an input selector button within 8 seconds. Zone 2 turns on, the Z2 indicator lights on the display. To select AM or FM, press the Tuner input selector button repeatedly. To select the same source as the main rooms, press Zone 2 repeatedly until Z2 Selector: Source appears on the display. To turn off Zone 2, press Off. The zone is turned off.

Press Zone2 followed by Muting.

Tip To unmute, press Zone2 followed by Muting again.

Adjusting the Tone and Balance of Zone 2

1 2 3

On the AV receiver, press Zone 2. Press the AV receivers Tone repeatedly to select Bass, Treble or Balance. Use + and to adjust the Bass, Treble or Balance. You can boost or cut the Bass or Treble from 10dB to +10dB in 2 dB steps. You can adjust the balance from 0 in the center to +10dB to the right or +10dB to the left in 2 dB steps.

Operating on the remote controller To control Zone 2, you must press Zone2 on the remote controller first. 8Receiver
Zone2 Input selector buttons Muting VOL q/w

Note Only analog input sources are output from the ZONE 2 PRE/LINE OUT L/R jacks and ZONE 2 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, verify that the source is connected to an analog input. While Zone 2 is on, u functions will not work. You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room. Namely, if you have selected an FM station for the main room, that station will also be output in Zone 2. When you have selected NET or USB as the input selector, the last selector selected will be set for both Main room and Zone 2. Zone 2 can also be unmuted by adjusting the volume. When Zone 2 is activated and its input selector is selected, the power consumption of standby mode slightly increases. When setting the AV receiver to standby mode while Zone 2 is active, the Z2 indicator is dimly lit. The Zone 2 level, balance, and tone functions have no effect on the ZONE 2 PRE/LINE OUT jacks when the Zone 2 Out setting is set to Fixed ( page 55).

1 2

Press Zone2 and then press 8Receiver. Zone 2 turns on, the Z2 indicator lights on the display. To select an input source for Zone 2, press Zone2, followed by an input selector button. To select AM or FM, press the Tuner input selector repeatedly.
Note You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room.

To turn off Zone 2, press Zone2 followed by 8Receiver.

En

61

Using the 12V Triggers

The 12V triggers A, B, and C can be used to turn on 12V trigger-capable components automatically when they are selected as the input source. The triggers can be set so that they activate when a connected component is selected as the input source for the main room, Zone 2 or any combination of rooms. When triggered, the output from a 12V TRIGGER OUT goes high (+12 volts and 150 milliamperes max. at 12V TRIGGER OUT A; +12 volts and 25 milliamperes max. at 12V TRIGGER OUT B and C). See also 12V Trigger A/B/C Setup ( page 55).

Hookup Use a miniplug cable to connect the AV receivers 12V TRIGGER OUT A, B, or C jack to the 12 V trigger input on a connected component. When several components are turned on simultaneously by using triggers A, B, and C, depending on the type of components, a large amount of current may be drawn momentarily. To prevent this, you can delay trigger signals A, B, and C individually. Another application of trigger delay is eliminating the thump noise thats sometimes heard when a source component is turned on. You can accomplish this by delaying the trigger signal for your power amplifier, so that it's the last component to be turned on.

En

62

Using the Remote Controller in Zone 2 and Multiroom Control Kits

To control the AV receiver with the remote controller while youre in the Zone 2 room, youll need a commercially available multiroom remote control kit. Multiroom kits are made by Niles and Xantech. These kits can also be used when there isnt a clear line of sight to the AV receivers remote sensor, such as when its installed inside a cabinet.

Using a Multiroom Kit with a Cabinet

In this setup, the IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver located in the cabinet via the connecting block.

Connecting block IR IN A or B

IR receiver

Using a Multiroom Kit with Zone 2

In this setup, the IR receiver in Zone 2 picks up the infrared signals from the remote controller and feeds them through to the AV receiver in the main room via the connecting block.
IR IN A or B Connecting block IR receiver Inside cabinet Signal flow

Remote controller

Using a Multiroom Kit with Other Components

In this setup, an IR emitter is connected to the AV receivers IR OUT jack and placed in front of the other components remote control sensor. Infrared signals received at the AV receivers IR IN A or B jack are fed through to the other component via the IR emitter. Signals picked up by the AV receivers remote control sensor are not output.

Remote controller Main room Signal flow Zone 2

The miniplug cable from the connecting block should be connected to the AV receivers IR IN A or B jack, as shown below. The IR IN A and B jacks are identical. Up to two IR receivers can be connected.
From the connecting block

IR IN A or B IR OUT

Connecting block AV receiver IR emitter

IR receiver

Remote controller Other component

Miniplug cable Signal flow

The IR emitter should be connected to the AV receivers IR OUT jack, as shown below.

Miniplug cable AV receiver Remote controller sensor

Emitter Miniplug IR emitter AV receiver

Signal flow

En

63

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock
The Dock is sold separately. Models sold are different depending on the region. For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock. Operating Notes
Functionality depends on your iPod/iPhone model and generation. Before selecting a different input source, stop your iPod/iPhone playback to prevent the AV receiver from selecting the iPod/iPhone input source by mistake. If any accessories are connected to your iPod/iPhone, the AV receiver may not be able to select the input source properly. When connecting the UP-A1 Dock to the radio tuner UP-HT1 (North American models)/UP-DT1 (Australian models) with AUTO selected by the tuners Mode Selector switch, you can switch the input source between UP-A1 Dock and the tuner, by pressing Port repeatedly on the front panel. While your iPod/iPhone is in the UP-A1 Dock, its volume control has no effect. If you adjust your iPod/iPhone models volume control while its in the UP-A1 Dock, make sure its not set too high before you reconnect your headphones. The Auto Power On function will not work if you set your iPod/iPhone in the UP-A1 Dock while it is playing. When Zone 2 is turned on, you cant use Auto Power On and Direct Change functions. Do not turn off the power with the iPod/iPhone still connected to this unit via the UP-A1 Dock. Set your iPod/iPhone in the UP-A1 Dock after the AV receiver turns on. The Charge Mode setting must be set to On to enable the Auto Power On and Direct Change functions ( page 53).

UP-A1 Dock
With the UP-A1 Dock, you can easily play the music, photos, or movies stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound. You can use the AV receivers remote controller to operate your iPod/iPhone. System Function The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song. Auto Power On If you start iPod/iPhone playback while the AV receiver is on standby, the AV receiver will automatically turn on and select your iPod/iPhone as the input source. Direct Change If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically select your iPod/iPhone as the input source. Using the AV receivers Remote Controller You can use the AV receivers remote controller to control basic iPod/iPhone functions ( page 65).

Using Your iPod/iPhone Alarm Clock You can use the Alarm Clock function of your iPod/iPhone to automatically turn on your iPod/iPhone and the AV receiver at a specified time. The AV receivers input source will automatically be set to the Port selector.
Note To use this function, your iPod/iPhone must be in the UP-A1 Dock, and the UP-A1 Dock must be connected to the AV receiver. This function works only in Standard mode ( page 66). When you use this function, be sure to set the AV receivers volume control to a suitable level. When Zone 2 is turned on, you cant use this function. This function doesnt work when alarms sounds are set on your iPod/iPhone. The Charge Mode setting must be set to On to enable the Alarm Clock function ( page 53).

Charging Your iPod/iPhone Battery When the UP-A1 Dock with docked iPod/iPhone is connected to the AV receiver, the battery of your iPod/iPhone is charged. Charging occurs when AV receiver is set to on or standby. You can specify how the power is fed to your iPod/iPhone when the AV receiver is in standby mode ( page 53).
Note When the UP-A1 Dock with docked iPod/iPhone is connected, the power consumption on standby mode slightly increases.

En

64

 Status Messages If either of the following messages is not displayed on the AV receivers display, check the connection to your iPod/iPhone. PORT Reading The AV receiver is checking the connection with the dock. PORT Not Support The AV receiver do not support the connected dock. PORT UP-A1 UP-A1 Dock is connected.
Note The AV receiver displays the message UP-A1 for several seconds after recognizing the UP-A1.

iPod/iPhone Alarm If you use the Alarm function on your iPod/iPhone to start playback, the AV receiver will turn on at the specified time and select your iPod/iPhone as the input source automatically.
Note Linked operations do not work with video playback or when the alarm is set to play a sound. If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work. This function works only in Standard mode ( page 66). The System On function may not work depending on the RI Dock.

Operating Notes
Use the AV receivers volume control to adjust the playback volume. While your iPod/iPhone is inserted in the RI Dock, its volume control has no effect. If you do adjust the volume control on your iPod/iPhone while its inserted in the RI Dock, be careful that its not set too loud before you reconnect your headphones. Note On the iPod with video and iPod nano (1st generation), the click wheel is disabled during playback.

RI Dock
With the RI Dock, you can easily play the music stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows and videos on your TV. In addition, the onscreen display (OSD) allows you to view, navigate, and select your iPod/iPhone models contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receivers remote controller to operate your iPod/iPhone.
Note Enter the appropriate remote control code before using the AV receivers remote controller for the first time ( page 67). Connect the RI Dock to the AV receiver with an u cable ( page 20). Set the RI Docks RI MODE switch to HDD or HDD/DOCK. Set the AV receivers Input Display to DOCK ( page 41).

Controlling Your iPod/iPhone

By pressing the Remote Mode thats been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See Entering Remote Control Codes for details on entering a remote control code ( page 67). See the Docks instruction manual for more information.

System Function System On When you turn on the AV receiver, the RI Dock and iPod/iPhone turn on automatically. In addition, when RI Dock and iPod/iPhone are on, the AV receiver can be turned on by pressing 8Source. Auto Power On If you press the remote controllers 1 (Playback) while the AV receiver is on standby, the AV receiver will automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback. Direct Change If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected. Other Remote Controllers You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

UP-A1 Dock
Port is preprogrammed with the remote control code for controlling a Dock via Universal Port. You can control your iPod/iPhone when Port is selected as the input source.

RI Dock
Set the RI Docks RI MODE switch to HDD or HDD/DOCK. 8Source may not work with a remote control code (without u). In this case, make an u connection and enter the remote control code 81993 (with u). With the RI Control Make an u connection and enter the remote control code 81993 (with u). Set the AV receivers Input Display to DOCK ( page 41). Without the RI Control You must enter the remote control code 82990 first ( page 68).

En

65

: Available buttons
Press the appropriate Remote Mode first. Onkyo Dock UP-A1 Dock u Dock *2 *5 *6

e f g h i a b k c d l j

Buttons a Top Menu*1 b q/w/e/r, Enter Playlist e/r c 1, 3, 2, 5, 4, 7, 6 d Repeat Random e 8Source*3 f Display*4 g Muting h Album +/ i VOL q/w j Menu k Return l Mode

With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected. For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock. *1 Top Menu works as the mode button when used with the DS-A2 RI Dock. *2 In Extended mode (see *5), e/r is used as the page jump button. This allows you to quickly locate your favorite songs even when such lists as the song or artist lists are very long. *3 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or off. Also, your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits the On command. Similarly, if your iPod/iPhone is already off, it will remain off when the remote controller transmits the Off command. *4 Display turns on backlight for 30 seconds. *5 Press Mode to switch between the following modes: Standard mode Nothing is displayed on your TV. Contents are browsed and selected on your iPod/iPhone display. Extended mode (Music) The music contents (artists, albums, songs, and so on) are displayed on your TV, and you can browse and select them on screen. Extended mode (Video) The video contents (Movies, Music Videos, TV Shows, Video Podcasts or Rentals) are displayed on your TV, and you can browse and select them on screen. *6 Resume mode With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the RI Dock or Standard mode is selected. Note In Extended mode (see *5), playback will continue even if the AV receiver is turned off. In Extended mode (see *5), you cannot operate your iPod/iPhone directly. In Extended mode (see *5), it may take some time to acquire the contents. In Extended mode (see *5), the on-screen navigation menus only appear on a TV that is connected to the HDMI output.

En

66

Controlling Other Components

You can use the AV receivers remote controller to control your other AV components, including those made by other manufacturers. This section explains how to enter the remote control code (with the default underlined) for a component that you want to control: DVD, TV, CD, etc.

7 8

Use q/w to select a brand, and then press Enter. A remote control code with its instructions are displayed. Follow the procedure. If you can control the component, use q/w to select OK, and then press Enter. The Remote Mode Setup menu appears. If you cannot control the component, use q/w to select Try next code and press Enter. The next code is displayed.

Preprogrammed Remote Control Codes

The following Remote Mode buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components. For details on controlling these components, see the indicated pages.
BD/DVD Integra/Onkyo Blu-ray Disc player TV/CD Port

Entering Remote Control Codes

Youll need to enter a code for each component that you want to control.

( page 68) Integra/Onkyo CD player ( page 68) Onkyo Universal Port Option ( page 65)

1 2

Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.). While holding down the Remote Mode to which you want to assign a code, press and hold down Display (about 3 seconds). The remote indicator lights.
Note Remote control codes cannot be entered for Receiver and Zone 2. Only TV remote control codes can be entered for TV. Except for Receiver, TV and Zone 2, remote control codes from any category can be assigned to the Remote Mode. However, these buttons also work as input selector buttons ( page 23), so choose a Remote Mode that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code.

Looking up for Remote Control Code

You can look up for an appropriate remote control code from the on-screen setup menu.
Note This can only be carried out using the on-screen setup menu.

Press Receiver followed by Setup. The main menu appears on-screen.

Tip If the main menu doesnt appear, make sure the appropriate external input is selected on your TV.

2 3 4 5 6

Use q/w to select Remote Controller Setup, and then press Enter. Use q/w to select Remote Mode Setup, and then press Enter. Use q/w to select a remote mode, and then press Enter. The menu of category selection appears. Use q/w to select a category, and then press Enter. The panel for brand name input appears. Use q/w/e/r to select a character, and then press Enter. Repeat this step for the first three characters of the brand name. When you have entered the 3rd character, select Search and press Enter. A list of brand names is retrieved. If the desired brand name is not found: Use r to select Not Listed, and then press Enter. The panel for brand name input appears.

Within 30 seconds, use the number buttons to enter the 5-digit remote control code. The remote indicator flashes twice. If the remote control code is not entered successfully, the remote indicator will flash once slowly.

Note Though the provided remote control codes are correct at the time of printing, they are subject to change.

En

67

Remote Control Codes for Integra/Onkyo Components Connected via u

Integra/Onkyo components that are connected via u are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

1 2

While holding down Receiver, press and hold down Home until the remote indicator lights (about 3 seconds). Within 30 seconds, press Receiver again. The remote indicator flashes twice, indicating that the remote controller has been reset.

Make sure the Integra/Onkyo component is connected with an u cable and an analog audio cable (RCA). See Connecting Integra/Onkyo u Components for details ( page 20). Enter the appropriate remote control code for Remote Mode, referring to the previous section. 42157: Onkyo cassette tape deck with u 81993: Onkyo Dock with u Press Remote Mode, point the remote controller at the AV receiver, and operate the component.

Controlling Other Components

By pressing the Remote Mode thats been programmed with the remote control code for your component, you can control your component as described below. For details on entering a remote control code for other components, see Entering Remote Control Codes ( page 67).

Controlling a TV
TV is preprogrammed with the remote control code for controlling a TV that supports the p*1 (limited to some models). The TV must be able to receive remote control commands via p and be connected to the AV receiver via HDMI. If controlling your TV via p doesnt work very well, program your TVs remote control code into TV and use the TV remote mode to control your TV. Use the following remote control codes: 11807/13100/13500: TV with p

Controlling Integra/Onkyo components without u If you want to control an Integra/Onkyo component by pointing the remote controller directly at it, or you want to control an Integra/Onkyo component thats not connected via u, use the following remote control codes: 30627: Integra/Onkyo DVD player without u 71817: Integra/Onkyo CD player without u 32900/33100/33500: Integra/Onkyo Blu-ray Disc player 32901/33104/33504: Integra/Onkyo HD DVD player 70868: Onkyo MD recorder without u 71323: Onkyo CD recorder without u 82990: Onkyo Dock without u

Controlling a Blu-ray Disc/DVD Player, HD DVD Player or DVD Recorder

BD/DVD is preprogrammed with the remote control code for controlling a component that supports the p*1 (limited to some models). The component must be able to receive remote control commands via p and be connected to the AV receiver via HDMI. Use the following remote control codes: 32910/33101/33501/31612: Blu-ray Disc/DVD player with p
*1

Resetting Remote Mode Buttons

You can reset a Remote Mode to its default remote control code.

The p supported by the AV receiver is the CEC system control function of the HDMI standard.

1 2

While holding down Remote Mode that you want to reset, press and hold down Home until the remote indicator lights (about 3 seconds). Within 30 seconds, press Remote Mode again. The remote indicator flashes twice, indicating that the button has been reset. Each of Remote Mode is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

En

68

: Available buttons
Press the appropriate Remote Mode first. Components DVD player/DVD recorder Satellite receiver Cable receiver CD player/CD recorder MD recorder Cassette tape deck *3 *2 *2 *2 *2 *1 *1

h
Buttons a 8, Input, TV VOL q/w, Muting b Guide Top Menu c q/w/e/r, Enter TV

i j a b c d m n e f k l

d Setup e 1, 3, 2, 5, *1 4, 7, 6 f Search Repeat Random Mode

*1*2 *1 *2 *1*2 *2 *1*2 *1 *2 *1*2 *1 *2 *1

g Number: 1 to 9, 0 Number: +10 *1 h 8Source*4 i Display j Muting k CH +/ Disc +/ l PREV CH Menu

g o

m Return n Audio o CLR

*1

*2 *3 *4

The p function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard. These buttons function as colored buttons or A, B, C, D buttons. 3 (Pause) functions as reverse playback. When you press 8Source, the related component is turned on (or off).

Note See the Controlling Your iPod/iPhone about the operation of iPod/iPhone ( page 65).

Note With some components, certain buttons may not work as expected, and some may not work at all.

Blu-ray Disc player HD DVD player VCR/PVR

En

69

Appendix

Troubleshooting
If you have any trouble using the AV receiver, look for a solution in this section. If you cant resolve the issue yourself, contact the dealer from whom you purchased this unit. If you cant resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased this unit. To reset the AV receiver to its factory defaults, turn it on and, while holding down VCR/DVR, press 8On/Standby. Clear will appear on the display and the AV receiver will enter standby mode. When the power is restored after a power interruption, CHECK SP WIRE appears on the display
The protection circuit has been activated. Remove the power cord from the wall outlet immediately. Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer from whom you purchased this unit.

Audio
Note that resetting the AV receiver will delete your radio presets and custom settings.
Remote indicator

Theres no sound, or its very quiet

Make sure that the digital input source is selected properly. 44

Make sure that all audio connecting plugs are pushed 16 in all the way. Make sure that the inputs and outputs of all components are connected properly. Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal. Make sure that the speaker cables are not shorting. 17-20 13

Receiver

Make sure that the input source is properly selected. 23 13 Check the volume. The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment. If the MUTING indicator is flashing on the display, 41 press the remote controllers Muting to unmute the AV receiver. While a pair of headphones is connected to the 41 Phones jack, no sound is output from the speakers. If theres no sound from a DVD player connected to an HDMI IN, check the DVD players output settings, and be sure to select a supported audio format. Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

Home

To reset the remote controller to its factory defaults, while holding down Receiver, press and hold down Home until the remote indicator lights (about 3 seconds). Within 30 seconds, press Receiver again. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings.

With some DVD-Video discs, you need to select an audio output format from a menu. If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer. Make sure that none of the connecting cables are bent, twisted, or damaged. 35 46 53

Power
Cant turn on the AV receiver
Make sure that the power cord is properly plugged into the wall outlet. Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

Not all listening modes use all speakers. Specify the speaker distances and adjust the individual speaker levels. Make sure that the speaker setup microphone is not still connected. The input signal format is set to PCM or DTS. Set it to Off.

The AV receiver turns off unexpectedly

The AV receiver will automatically enter standby 57 mode when Auto Standby has been set and launches.

En

70

 Only the front speakers produce sound

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound. In the Mono listening mode, only the front speakers 48 output sound if the Output Speaker setting is set to Left / Right. Check the Speaker Configuration. 45

Depending on the input signal, some listening modes 3539 cannot be selected.

Cant get 6.1/7.1 playback

If no surround back speakers and front high speakers are connected, or the Zone 2 speakers are being used, 6.1/7.1 playback is not possible. Depending on the number of connected speakers, it is not always possible to select all of the listening modes. 3539

Only the center speaker produces sound

If you use the Dolby Pro Logic IIx Movie, Dolby Pro Logic IIx Music, or Dolby Pro Logic IIx Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker. In the Mono listening mode, only the center speaker 48 output sound if the Output Speaker setting is set to Center. Make sure the speakers are configured correctly. 45

The speaker volume cannot be set as required

Check to see if a maximum volume has been set. If the volume level of each individual speaker has been adjusted to high positive values, then the maximum master volume possible may be reduced. Note that the individual speaker volume levels are set automatically after the Audyssey 2EQ Room Correction and Speaker Setup has been performed. 54 31, 46

The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or Mono listening mode is selected, the surround speakers produce no sound.

Noise can be heard

Using cable ties to bundle audio cables with power cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode. Make sure the speakers are configured correctly. 45

An audio cable may be picking up interference. Try repositioning your cables.

The Late Night function doesnt work

Make sure the source material is Dolby Digital, Dolby Digital Plus, and Dolby TrueHD. 59

The center speaker produces no sound

When the Stereo or Mono listening mode is selected, the center speaker produces no sound. In the Mono listening mode, only the front speakers 48 output sound if the Output Speaker setting is set to Left / Right. Make sure the speakers are configured correctly. 45

About DTS signals

When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the DTS indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. With some CD and LD players, you wont be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesnt recognize it as a genuine DTS signal. In such cases, you may hear noise. Playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

The front high and surround back speakers produce no sound

Depending on the current listening mode, no sound may be produced by the front high and surround back speakers. Select another listening mode. 35

Depending on the sources, the sound produced by the front high and surround back speakers may be weak. Make sure the speakers are configured correctly. 45 While the Powered Zone 2 setting is set to Yes, 60 playback in the main room is reduced to 5.1channels and the front high and surround back speakers produce no sound.

The subwoofer produces no sound

When you play a source material that contains no information in the LFE channel, the subwoofer produces no sound. Make sure the speakers are configured correctly.

45

The beginning of audio received by an HDMI IN cant be heard

Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.

Theres no sound with a certain signal format

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

En

71

Video
Theres no picture
Make sure that all video connecting plugs are pushed 16 in all the way. Make sure that each video component is properly connected. If your TV is connected to the HDMI OUT, select - - - - - in the HDMI Input setup to watch composite video, and component video sources. If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to either the HDMI OUT or COMPONENT VIDEO OUT. 17, 18 43

Remote Controller
The remote controller doesnt work
Before operating this unit, be sure to press Receiver. Make sure that the batteries are installed with the correct polarity. Install new batteries. Dont mix different types of batteries, or old and new batteries. Make sure that the remote controller is not too far away from the AV receiver, and that theres no obstruction between the remote controller and the AV receivers remote control sensor. Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary. 4 4 4

18, 43

If the video source is connected to a composite video 18 input, your TV must be connected to the HDMI OUT or the corresponding composite video output. If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the HDMI OUT. 17, 43

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed. Make sure youve selected the correct remote controller mode. When using the remote controller to control other manufacturers AV components, some buttons may not work as expected. 11, 68

On your TV, make sure that the video input to which the AV receiver is connected is selected.

Theres no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is 85 not guaranteed. In addition, video signals from a PC are not guaranteed. When the resolution is set to any resolution not supported by the TV, no video is output from the HDMI outputs. If the message Resolution Error appears on the AV receivers display, this indicates that your TV does not support the current video resolution and you need to select another resolution on your DVD player. 43

Make sure youve entered the correct remote control 67 code. Make sure to set the same ID on both the AV receiver and remote controller. 55

Cant control other components

If its an Integra/Onkyo component, make sure that the u cable and analog audio cable are connected properly. Connecting only an u cable wont be enough. Make sure youve selected the correct remote controller mode. 20

11, 68

The on-screen menus dont appear

On your TV, make sure that the video input to which the AV receiver is connected is selected. When the AV receiver is not connected to a TV via HDMI, onscreen menus are not displayed.

For a proper operation of the remote controller as a 41 cassette tape deck is connected to the TV/CD IN jack, or as an RI Dock is connected to the TV/CD IN, VCR/DVR IN or GAME IN jacks, you must set the input display accordingly. If you cannot operate it, you will need to enter the appropriate remote control code. 67

The on screen display does not appear

Depending on the input signal, the on screen display 55 may not appear when the input signal from the HDMI IN is output to a device connected to the HDMI OUT.

To control another manufacturers component, point 67 the remote controller at that component. To control an Integra/Onkyo component thats 67 connected via u, point the remote controller at the AV receiver. Be sure to enter the appropriate remote control code first. To control an Integra/Onkyo component thats not 68 connected via u, point the remote controller at the component. Be sure to enter the appropriate remote control code first. The entered remote control code may not be correct. If more than one code is listed, try each one.

Tuner
Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesnt light
Relocate your antenna. Move the AV receiver away from your TV or computer. Listen to the station in mono. When listening to an AM station, operating the remote controller may cause noise. Passing cars and airplanes can cause interference. Concrete walls weaken radio signals. 28

En

72

If nothing improves the reception, install an outdoor antenna.

UP-A1 Dock for iPod/iPhone

Theres no sound
Make sure your iPod/iPhone is actually playing. Make sure your iPod/iPhone is properly inserted in the Dock. Make sure the UP-A1 Dock is connected to the UNIVERSAL PORT jack on the AV receiver.

Zone 2
Theres no sound
Only components connected to analog inputs can be played in Zone 2.

The Zone 2 speakers produce no sound

Powered Zone 2 cannot be used if Speakers Type (Front) is set to Bi-Amp. 45

Make sure the AV receiver is turned on, the correct input source is selected, and the volume is turned up. Make sure the plugs are pushed in all the way. Try resetting your iPod/iPhone.

Music Server and Internet Radio

Cant access the server or Internet radio

Theres no video
Make sure that your iPod/iPhone models TV OUT setting is set to On. Make sure the correct input is selected on your TV or the AV receiver.

Check the network connection between the AV receiver and your router or switch.

Make sure that your modem and router are properly connected, and make sure they are both turned on. Make sure the server is up and running and compatible with the AV receiver. Check the Network settings. 76, 78 57

Some versions of the iPod/iPhone do not output video.

The AV receivers remote controller doesnt control my iPod/iPhone

Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the Dock. The iPod/iPhone cannot be operated while its displaying the Apple logo. Make sure youve selected the right remote mode. When you use the AV receivers remote controller, point it toward your AV receiver. 23

Playback stops while listening to music files on the server

Make sure your server is compatible with the AV receiver. 76, 78

If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server. If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted. Reduce the number of playback devices on the network, upgrade your network, or use a switch instead of a hub.

When connecting the UP-A1 Dock to the radio tuner UP-HT1 (North American models)/UP-DT1 (Australian models) with AUTO selected with the tuners Mode Selector switch, you can switch the input source between the UP-A1 Dock and the tuner, by pressing Port repeatedly on the front panel. If you still cant control your iPod/iPhone, start playback by pressing your iPod/iPhone models Play button. Remote operation should then be possible. Try resetting your iPod/iPhone. Depending on your iPod/iPhone, some buttons may not work as expected.

Cant connect to the AV receiver from a Web browser

If youre using DHCP, your router may not always 57 allocate the same IP address to the AV receiver, so if you find that you cant connect to a server or Internet radio station, recheck the AV receivers IP address on the Network screen. Check the Network settings. 57

The AV receiver unexpectedly selects your iPod/iPhone as the input source

Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks.

USB Device Playback

Cant access the music files on a USB device
Make sure the USB device is plugged in properly. The AV receiver supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class. USB memory devices with security functions cannot be played.

Recording
Cant record
On your recorder, make sure the correct input is selected.

To prevent signal loops and damage to the AV receiver, input signals are not fed through to outputs with the same name (VCR/DVR IN to VCR/DVR OUT).

En

73

Others
Standby power consumption
In the following cases, the power consumption in 18, 56, standby mode may reach up to a maximum of 43 W: 57 You are using the Universal Port jack. Network Control is set to Enable in the Network setting. HDMI Control (RIHD) setting is set to On. (Depending on the TV status, the AV receiver will enter standby mode as usual.) The HDMI Through setting is set to other than Off.

The sound changes when I connect my headphones

When a pair of headphones is connected, the listening mode is set to Stereo, unless its already set to Stereo, Mono or Direct.

The speaker distance cannot be set as required

In some cases, corrected values suitable for home theater use may be set automatically.

The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source that you want to set and the Setup button simultaneously. While holding down the input selector button, press Setup until Video ATT:ON appears on the display. Then, release both buttons. To reactivate the setting, repeat the above process so that Video ATT:OFF appears on the display, and release the buttons. Video Attenuation This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT, Game or AUX input. If you have a game console connected to the composite video input, and the picture isnt very clear, you can attenuate the gain. Video ATT:OFF: (default). Video ATT:ON: Gain is reduced by 2 dB. If the picture on your TV/monitor connected to HDMI OUT is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the CBL/SAT and 8On/Standby buttons on the AV receiver. While holding down CBL/SAT, press 8On/Standby until Off appears on the display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until On appears on the display and release the buttons. The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the units malfunction. Before you record important data, make sure that the material will be recorded correctly. Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

How do I change the language of a multiplex source

Use the Multiplex setting on the Audio Adjust 48 menu to select Main or Sub.

The u functions dont work

To use u, you must make an u connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. 20

The functions System On/Auto Power On and Direct Change dont work for components connected via u
These functions dont work when Zone 2 is turned on. 20

When performing Automatic Speaker Setup, the measurement fails showing the message Ambient noise is too high.
This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds.

En

74

Important Note Regarding Video Playback The AV receiver can upconvert component video and composite video sources for display on a TV connected to the HDMI OUT. However, if the picture quality of the source is poor, upconversion may make the picture worse or disappear altogether. In this case, try the following:

If the video source is connected to a component video input, connect your TV to the COMPONENT VIDEO OUT. If the video source is connected to a composite video input, connect your TV to the MONITOR OUT V. On the main menu, select Input/Output Assign, and then select Component Video Input ( page 44). If the video source is connected to COMPONENT VIDEO IN 1, select the relevant input selector, and assign it to IN1. If the video source is connected to COMPONENT VIDEO IN 2, select the relevant input selector, and assign it to IN2. If the video source is connected to a composite video input, select the relevant input selector, and assign it to - - - - -.

En

75

Network/USB Features
Connecting to the Network
The following diagram shows how you can connect the AV receiver to your home network. In this example, its connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in.
Internet radio

Network Requirements
Ethernet Network For the best results, a 100Base-TX switched Ethernet network is recommended. Although its possible to play music on a computer thats connected to the network wirelessly, playback may be unreliable, so it is recommended to use wired connections. Ethernet Router A router manages the network, data-routing and supplying of IP addresses. Your router must support the following: NAT (Network Address Translation). NAT allows several networked computers to access the Internet simultaneously via a single Internet connection. The AV receiver needs Internet access for Internet radio. DHCP (Dynamic Host Configuration Protocol). DHCP supplies IP addresses to the network devices, allowing them to configure themselves automatically. A router with a built-in 100Base-TX switch is recommended. Some routers have a built-in modem, and some ISPs require you to use specific routers. Please consult your ISP or computer dealer if youre unsure. CAT5 Ethernet cable Use a shielded CAT5 Ethernet cable (straight-type) to connect the AV receiver to your home network. Internet Access (for Internet radio) To receive Internet radio, your Ethernet network must have Internet access. A narrowband Internet connection (e.g., 56K modem, ISDN) will not provide satisfactory results, so a broadband connection is strongly recommended (e.g., cable modem, xDSL modem, etc). Please consult your ISP or computer dealer if youre unsure.
Note To receive Internet radio with the AV receiver, your broadband Internet connection must be working and able to access the Web. Consult your ISP if you have any problems with your Internet connection. The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see Network ( page 57). The AV receiver does not support PPPoE settings, so if you have a PPPoE-type Internet connection, you must use a PPPoEcompatible router. Depending on your ISP, you may need to specify a proxy server to use Internet radio. If your computer is configured to use a proxy server, use the same settings for the AV receiver ( page 57).

Modem

WAN LAN

Router

Computer or media server

En

76

Server Requirements
Server playback The AV receiver can play digital music files stored on a computer or media server and supports the following technologies: Windows Media Player 11 Windows Media Player 12 Windows Media Connect 2.0 DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media Player 11 is already installed. Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site. The computer or media server must be on the same network as the AV receiver. Each folder may contain up to 20000 music files, and folders may be nested up to 16 levels deep.
Note Depending on the media server, the AV receiver may not recognize it, or may not be able to play its music files.

USB Device Requirements

USB mass storage device class (but not always guaranteed). FAT16 or FAT32 file system format. If the storage device has been partitioned, each section will be treated as an independent device. Each folder may contain up to 20,000 music files and folders, and folders may be nested up to 16 levels deep. USB hubs and USB devices with hub functions are not supported.
Note If the media you connect is not supported, the message No Storage will appear on the display. If you connect a USB hard disk drive to the AV receivers USB port, we recommend that you use its AC adapter to power it. The AV receiver supports USB MP3 players that support the USB Mass Storage Class standard, which allows USB devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer to your USB MP3 players instruction manual for details. Protected WMA music files on an MP3 player cannot be played. Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand. MP3 players containing music files that are managed with special music software are not supported. Operation is not guaranteed for all USB devices, which includes the ability to power them. Do not connect your USB device via a USB hub. The USB device must be connected directly to the AV receivers USB port. If the USB device contains a lot of data, the AV receiver may take a while to read it. USB devices with security functions cannot be played.

Minimum system requirements for Windows Media Player 11 on Windows XP Operating system Windows XP Home Edition (SP2), Windows XP Professional (SP2), Windows XP Tablet PC Edition (SP2), Update Rollup 2 for Windows XP Media Center Edition 2005 (KB900325), October 2006 Update Rollup for Windows XP Media Center Edition (KB925766) Processor: 233 MHz Intel Pentium II, Advanced Micro Devices (AMD), etc. Memory: 64 MB Hard disk: 200 MB of free space Drive: CD or DVD drive Modem: 28.8 kbps Sound card: 16-bit sound card Monitor: Super VGA (800 x 600) Video card: 64 MB VRAM, DirectX 9.0b Software: Microsoft ActiveSync (only when using a Windows Mobile-based Pocket PC or smartphone) Web browser: Microsoft Internet Explorer 6 or Netscape 7.1 Remote playback Windows Media Player 12 DLNA-certified (within DLNA Interoperability Guidelines version 1.5) media server or controller device. Setting varies depending on the device. Refer to your devices instruction manual for details. If the operating system of your personal computer is Windows 7, Windows Media Player 12 is already installed. For more information, see the Microsoft web site.

En

77

Supported Audio File Formats

For server playback and playback from a USB device, the AV receiver supports the following music file formats. Variable bit-rate (VBR) files are supported. However, playback time may not be display correctly.
Note With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis. In the case of server playback, the below-mentioned file formats may not be played depending on the server type.

LPCM (Linear PCM) Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. Quantization bit: 8 bit, 16 bit, 24 bit
*

Only for playback via network.

About DLNA
The Digital Living Network Alliance is an international, cross-industry collaboration. Members of DLNA develop a concept of wired and wireless interoperable networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home. The AV receiver complies with the DLNA Interoperability Guidelines version 1.5.

MP3 (.mp3 or .MP3) MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 format with a sampling rate of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 8 kbps and 320 kbps. Incompatible files cannot be played. WMA (.wma or .WMA) WMA stands for Windows Media Audio and is an audio compression technology developed by Microsoft Corporation. Audio can be encoded in WMA format by using Windows Media Player. WMA files must have the copyright option turned off. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, bitrates of between 5 kbps and 320 kbps, and WMA DRM are supported. WMA Pro/Voice formats are not supported. WMA Lossless (.wma or .WMA) Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz are supported. Quantization bit: 16 bit, 24 bit WAV (.wav or .WAV) WAV files contain uncompressed PCM digital audio. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. Quantization bit: 8 bit, 16 bit, 24 bit AAC (.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/ .3GP or .3G2) AAC stands for MPEG-2/MPEG-4 Audio. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz and bitrates of between 8 kbps and 320 kbps are supported. FLAC (.flac or .FLAC) FLAC is a file format for lossless audio data compression. Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported. Quantization bit: 8 bit, 16 bit, 24 bit Ogg Vorbis (.ogg or .OGG) Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 48 kbps and 500 kbps are supported. Incompatible files cannot be played.

En

78

Firmware Update
To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully. Update via network You need a wired Internet connection to update the firmware. Update via USB storage ( page 80) Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of available space to update the firmware.
Note Check the network connection before updating. Do not touch the any cable or device connected to the AV receiver during the update process. Do not attempt to access the AV receiver from your PC while it is being updated. Do not shutdown the power of the AV receiver while it is being updated. The storage media in the USB card reader may not work. If the USB device is partitioned, each section will be treated as an independent device. If the USB device contains a lot of data, the AV receiver may take a while to read it. Operation is not guaranteed for all USB devices, which includes the ability to power them. Onkyo takes no responsibility whatsoever for the loss or damage of data resulting from the use of a USB device with the AV receiver. Onkyo recommends that you back up your important music files beforehand. If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC adapter to power it. USB hubs and USB devices with hub functions are not supported. Do not connect your USB device via a USB hub. USB devices with security functions are not supported.

Updating the Firmware via Network

The AV receiver allows you to update the firmware using network connection on the rear panel.
Note Make sure your AV receiver and TV are turned on and an Ethernet cable is connected to the rear panel of the AV receiver. Never unplug or turn off the AV receiver while it is being updated. Never plug or unplug an HDMI or Ethernet cable during the update process. Do not attempt to access the AV receiver from your PC while it is being updated. Never unplug the power cord during the update process. It takes maximum 60 minutes to complete the firmware update. The AV receiver will retain all your settings after the update is finished.

Before you start

Set the HDMI Control (RIHD) setting to Off ( page 56). Turn off the controller device connected via Ethernet cable. Turn off Zone 2. Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc.

Update procedure

Press Receiver followed by Setup on the remote controller. The Setup menu will be displayed on the TV screen. The procedures thereafter can also be performed on the AV receiver by using its Setup, arrow and Enter buttons. Select Hardware Setup and press Enter. Select Firmware Update and press Enter. Note that the Firmware Update option will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable. Select Via NET and press Enter. Select Update and press Enter. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again. The message Completed! appears on the front display of the AV receiver, indicating that the update has been completed.

Limitation of liability The program and accompanying online documentation are furnished to you for use at your own risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective profits, loss of data, or for any other reason whatsoever. See the Integra web site for latest information.

2 3 4 5

En

79

Using 8On/Standby on the front panel, turn off and on the AV receiver. Do not use 8Receiveron the remote controller. Congratulations! You now have the latest firmware installed on your Integra AV receiver.

Updating the Firmware via USB

The AV receiver allows you to update the firmware using a USB device.
Note Never unplug or turn off the AV receiver during the update process. Never plug or unplug an HDMI cable or a USB device during the update process. Never unplug the USB storage device containing the firmware file or the AC power cord during the update process. Do not attempt to access the AV receiver from your PC while it is being updated. It takes maximum 60 minutes to complete the firmware update. The AV receiver will retain all your settings after the update is finished.

Troubleshooting
Case 1: If No Update is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further. Case 2: If an error occurs, Error!! *-** No media is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action. Errors during an update via network
Error Code
*-10, *-20 *-11, *-13, *-21, *-28

Before you start

Set the HDMI Control (RIHD) setting to Off ( page 56). Turn off the controller device connected via Ethernet cable. Turn off Zone 2. Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc. If there is any data in the USB device, remove it first.

Description The Ethernet cable was not detected. Reconnect the cable properly. Internet connection error. Check the following items: Make sure the IP address, subnet mask, gateway address, and DNS server are configured properly. Make sure the router is turned on. Make sure the AV receiver and the router are connected with an Ethernet cable. Make sure your router is configured properly. See the instruction manual of the router. If your network allows only one client connection and there is any other device already connected, the AV receiver will not be able to access the network. Consult your Internet Service Provider (ISP). If your modem does not function as a router, you will need a router. Depending on your network, you may need to configure the proxy server if necessary. See the document provided by your ISP. If you are still unable to access the Internet, the DNS or proxy server may be temporarily down. Contact your ISP. Retry the update procedure from the beginning. If the error persists, please contact Integra Support ( page 81) and provide the error code.

Update procedure

1 2

Connect a USB device to your PC. If there is any data in the USB device, remove it first. Download the firmware file from the Integra web site. The file name is as follows: ONKAVR****_************.zip Unzip the downloaded file. The following three files are created: ONKAVR****_************.of1 ONKAVR****_************.of2 ONKAVR****_************.of3

3 4 5 6 7

Copy the extracted files to the USB device. Be careful not to copy the zip file. Remove the USB device from your PC and connect it to the USB port on the AV receiver. Make sure the AV receiver and TV are turned on. If the AV receiver is in standby mode, press 8On/Standby on the AV receiver to light up the front display. Select the USB input source. Now Initializing is displayed on the front display and then the name of the USB device is displayed. It takes 20 to 30 seconds to recognize the USB device. Press Receiver followed by Setup on the remote controller. The setup menu will be displayed on the TV screen. The procedures thereafter can also be performed on the AV receiver by using its Setup, arrow and Enter buttons.

Others

Case 3: If an error occurs during the update process, disconnect then reconnect the AC power cord and try again. Case 4: If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update. Case 5: If you do not have an Internet connection, please contact Integra Support ( page 81).

En

80

8 9 10 11

Select Hardware Setup and press Enter. Select Firmware Update and press Enter. Select Via USB and press Enter. Select Update and press Enter. The update process will begin. During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the front display of the AV receiver. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again. Do not turn off the AV receiver and do not remove the USB device during the update process. The message Completed! appears on the front display of the AV receiver, indicating that the update has been completed. Using 8On/Standby on the front panel, turn off the AV receiver and then remove the USB device. Do not use 8Receiver on the remote controller. Congratulations! You now have the latest firmware installed on your Integra AV receiver.

Troubleshooting
Case 1: If No Update is displayed on the front display of the AV receiver, it means that the firmware has already been updated. You do not need to do anything further. Case 2: If an error occurs, Error!! *-** No media is displayed on the front display of the AV receiver. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action. Errors during an update via USB
Error Code
*-10, *-20

Description The USB device was not detected. Make sure the USB flash memory or USB cable is properly connected to the USB port. If the USB storage device has its own power supply, use it to power the USB device. The firmware file was not found in the root folder of the USB device, or the firmware file is for another model. Retry and download the file on the support page of the web site, following the on-site instructions. If the error persists, please contact Integra Support and provide the error code. Retry the update procedure from the beginning. If the error persists, please contact Integra Support and provide the error code.

12 13

*-14

Others

Case 3: If an error occurs during the update, disconnect then reconnect the AC power cord and try again. Case 4: If an error occurs due to a wrong selection of input sources, turn off and on the AV receiver. Then retry the update.
ONKYO SOUND & VISION CORPORATION
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN The Americas Integra Division of ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET <http://www.integrahometheater.com/> Europe ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 <http://www.eu.onkyo.com/> China, Hong Kong ONKYO CHINA LIMITED Unit 1&12, 9/F, Ever Gain Plaza Tower 1, 88, Container Port Road, Kwai Chung, N.T., Hong Kong Tel: 852-2429-3118 Fax: 852-2428-9039 <http://www.onkyochina.com/> Asia, Oceania, Middle East, Africa Please contact an ONKYO distributor referring to Onkyo SUPPORT site. <http://www.intl.onkyo.com/support/local_support/index.html>

En

81

Connection Tips and Video Signal Path

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide. The on-screen setup menus appear only on a TV that is connected to the HDMI OUT. If your TV is connected to the MONITOR OUT V or the COMPONENT VIDEO OUT, use the AV receivers display when changing settings.

Video Connection Formats

Video component can be connected by using any one of the following video connection formats: composite video, PC IN (Analog RGB), component video or HDMI, the latter offering the best picture quality. Video input signals flow through the AV receiver as shown, with composite video, PC IN (Analog RGB) and component video sources all being upconverted for the HDMI output. The composite video and component video outputs carry their respective input signals as they are. When you connect an audio component to an HDMI or COMPONENT input, you must assign that input to an input selector ( page 43).
Tip For optimal video performance, THX recommends that video signals pass through the system without upconversion (e.g., component video input passing through to component video output). Video Signal Flow Chart Blu-ray Disc/DVD player, etc.

Composite

PC IN (Analog RGB)

Component

HDMI

IN
AV receiver

MONITOR OUT
Composite Component HDMI

TV, projector, etc.

Signal Selection If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, component video, composite video. However, for component video only, regardless of whether a component video signal is actually present, if a component video input is assigned to the input selector, that component video input will be selected. And if no component video input is assigned to the input selector, this will be interpreted as no component video signal being present. In the Signal Selection Example shown on the right, video signals are present at both the HDMI and composite video inputs. However, the HDMI signal is automatically selected as the source and the video is output by the HDMI outputs.

Signal Selection Example Blu-ray Disc/DVD player, etc.

Composite

Component

HDMI

IN
AV receiver

MONITOR OUT
Composite Component HDMI

TV, projector, etc.

En

82

Audio Connection Formats

Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI. When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. For example, audio signals connected to an optical or coaxial digital input are not output by the analog VCR/DVR OUT. If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.
*1 *2

Audio Signal Flow Chart Blu-ray Disc/DVD player, etc.

Analog Optical Coaxial HDMI

IN
AV receiver

*1
Analog

*1
OUT

*1

HDMI *1 *2

TV, projector, etc. Depends on the Audio TV Out setting ( page 56). This is possible when Audio Return Channel is set to Auto ( page 57), the TV/CD input selector is selected, and your TV is ARC capable.

En

83

About HDMI
Designed to meet the increased demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, Blu-ray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, and multichannel PCM). The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)*1, so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.) The AV receiver uses HDCP (High-bandwidth Digital Content Protection)*2, so only HDCP-compatible components can display the picture. The AV receivers HDMI interface is based on the following: Audio Return Channel, 3D, x.v.Color, DeepColor, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multichannel PCM.

Supported Audio Formats

2-channel linear PCM (32192 kHz, 16/20/24 bit) Multichannel linear PCM (up to 7.1 ch, 32192 kHz, 16/20/24 bit) Bitstream (DSD, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD High Resolution Audio, DTS-HD Master Audio) Your Blu-ray Disc/DVD player must also support HDMI output of the above audio formats.

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital Content Protection)*2, a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

*1 *2 *3

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG*3 in 1999. HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for HDMI/DVI. Its designed to protect video content and requires a HDCP-compatible device to display the encrypted video. DDWG (Digital Display Working Group): Lead by Intel, Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon Image, this open industry groups objective is to address the industrys requirements for a digital connectivity specification for highperformance PCs and digital displays.

Note The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so youll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported. The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or theres no sound from a component connected via HDMI, check its setup. Refer to the connected components instruction manual for details.

En

84

Using an RIHD-compatible TV, Player, or Recorder

p, which stands for Remote Interactive over HDMI, is the name of the system control function found on Integra/Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than p-compatible components cannot be guaranteed.

About p-compatible components

The following components are p-compatible (as of January 2011). TV Toshiba REGZA-LINK compatible TV Sharp TV Players/Recorders Onkyo and Integra p-compatible players Toshiba REGZA-LINK compatible players and recorders (only when used together with Toshiba REGZA-LINK compatible TV) Sharp players and recorders (only when used together with Sharp TV)
*

Operations that can be performed with p connection

For p-compatible TV The following linked operations are enabled by connecting the AV receiver to an p-compatible TV. The AV receiver will enter standby mode when the power of the TV is turned to standby. You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV receiver, or from the speakers of the TV. It is possible to output the video/audio coming from the antenna or from the input jack of the TV from the speakers connected to the AV receiver. (A connection such as optical digital cable or similar is required above the HDMI cable.) Input to the AV receiver can be selected with the remote controller of the TV. Operations such as volume adjustment or similar for the AV receiver can be performed from the remote controller of the TV. For p-compatible players/recorders The following linked operations are enabled by connecting the AV receiver to an p-compatible player/recorder. When the playback is started on the player/recorder, input of the AV receiver will switch to the HDMI input of the player/recorder that is playing back. Operation of the player/recorder is possible using the remote controller supplied with the AV receiver.
*

Models other than those mentioned above may have some interoperability if compatible with CEC, which is part of the HDMI Standard, but operation cannot be guaranteed.

Note For proper linked operations, do not connect more pcompatible components than the quantities specified below, to the HDMI input terminal. Blu-ray Disc/DVD players: up to three. Blu-ray Disc/DVD recorders/Digital Video Recorders: up to three. Cable/Satellite Set-top boxes: up to four. Do not connect the AV receiver to the other AV receiver/AV amplifier via HDMI. Proper linked operations are not guaranteed when more p-compatible components than the above-mentioned quantities are connected.

Depending on the model used, not all operations may be available.

En

85

 How to connect and setup

Confirm the connecting and setting. 1. Connect the HDMI OUT jack to the HDMI input jack of the TV.
Blu-ray Disc/DVD player, etc.

HDMI connection AV receiver DIGITAL AUDIO connection (OPTICAL) HDMI connection

TV, projector, etc.

2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable.
Note When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary ( page 57).

Confirm the settings. 1. Turn on the power for all connected components. 2. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. 3. Turn on the power of the Blu-ray Disc/DVD player/recorder. 4. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following. The AV receiver automatically turns on, and selects the input to which the Blu-ray Disc/DVD player/recorder is connected. The TV automatically turns on, and selects the input to which the AV receiver is connected. 5. Following the operating instructions of the TV, select Use the TV speakers from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver. 6. Select Use the speakers connected from the AV receiver from the menu screen of the TV, and confirm that the audio is output from the speakers connected to the AV receiver, and not from the TV speakers.
Note Perform the above operations when you use the AV receiver for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage.

3. Connect the HDMI output of the Blu-ray Disc/DVD player/recorder to the HDMI IN 1 jack of the AV receiver.
Note It is necessary to assign the HDMI input when connecting the Blu-ray Disc/DVD player/recorder to other jacks ( page 43). Do not assign the components connected to the HDMI IN to the TV/CD input at this time. Appropriate CEC (Consumer Electronics Control) operation can not be guaranteed.

Operate with the remote controller. For buttons that can be operated ( page 68).
Note Audio from DVD-Audio or Super Audio CD may not output from the TV speakers. You will be able to output the audio from the TV speakers by setting the audio output of the DVD player to 2ch PCM. (It may not be possible depending on the player models.) Even if you set to output audio on the TV speakers, audio will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, redo the operations on the TV. In case of an p connection with u and u audio control compatible components, do not connect the RI cable at the same time. On the TV, when you select anything other than the HDMI jack to which the AV receiver is connected, the input on the AV receiver will be switched to TV/CD. The AV receiver will automatically power on in conjunction when it determines it to be necessary. Even if the AV receiver is connected to an p compatible TV or player/recorder, it will not power on if it is not necessary. It may not power on in conjunction when the TV is set to output audio from the TV. Linked functions with the AV receiver may not work depending on the component model connected. In such cases, operate the AV receiver directly.

Change each item in the HDMI menu according to the following settings: HDMI Control (RIHD): On Audio Return Channel (ARC): Auto See details of each setting ( pages 56, 57).

En

86

Specifications
Amplifier Section
Rated Output Power All channels:

General
Power Supply (North American) AC 120 V, 60 Hz (Australian) AC 220 - 240 V, 50/60 Hz Power Consumption (North American) 6.2 A (Australian) 610 W Stand-by Power Consumption (North American) 0.2 W (Australian) 0.3 W Dimensions 435 mm 174.2 mm 326.3 mm (W H D) 17-1/8" 6-7/8" 12-7/8" Weight 11.4 kg (25.2 lbs.)

(North American) 100 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% (FTC) 125 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.1% (FTC) 115 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of 0.7% (FTC) (Australian) 7 ch 160 W at 6 ohms, 1 kHz, 1 ch driven of 1 % (IEC) Maximum Effective Output Power (Australian) 7 ch 175 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) Dynamic Power* * IEC60268-Short-term maximum output power 240 W (3 , Front) 210 W (4 , Front) 120 W (8 , Front) THD+N (Total Harmonic Distortion+Noise) 0.08% (20 Hz - 20 kHz, half power) Damping Factor 60 (Front, 1 kHz, 8 ) Input Sensitivity and Impedance (Unbalance) 200 mV/47 k (LINE) Rated RCA Output Level and Impedance 200 mV/2.2 k (REC OUT) Maximum RCA Output Level and Impedance 2 V/2.2 k (REC OUT) Frequency Response 20 Hz - 50 kHz/+1 dB, -3 dB (DSP bypass) Tone Control Characteristics 10 dB, 50 Hz (BASS) 10 dB, 20 kHz (TREBLE) Signal to Noise Ratio 106 dB (LINE, IHF-A) Speaker Impedance (North American) 6 - 16 (Australian) 4 - 16

HDMI
Input Output Video Resolution Audio Format Supported IN 1, IN 2, IN 3, IN 4, IN 5, AUX INPUT OUT 1080p Dolby TrueHD, DTS-HD Master Audio, DVD-Audio, DSD 3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD)

Video Inputs
Component Composite Analog RGB IN 1, IN 2 BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX PC IN

Video Outputs
Component Composite OUT MONITOR OUT, VCR/DVR OUT

Audio Inputs
Digital Analog Optical: 2 Coaxial: 2 BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX, TV/CD

Audio Outputs
Analog VCR/DVR, ZONE2 PRE/LINE OUT Multichannel Pre Outputs 7 (L, R, C, SL, SR, SBL or FHL, SBR or FHR) Subwoofer Pre Outputs 2 Speaker Outputs Main (L, R, C, SL, SR, SBL/FHL, SBR/FHR) + ZONE2 (L, R) Phones 1 (6.3 )

Video Section
Input Sensitivity/Output Level and Impedance 1 Vp-p/75 (Component Y) 0.7 Vp-p/75 (Component PB/CB, PR/CR) 1 Vp-p/75 (Composite) Component Video Frequency Response 5 Hz - 100 MHz/+0 dB, -3 dB

Tuner Section
FM Tuning Frequency Range (North American) 87.5 MHz - 107.9 MHz (Australian) 87.5 MHz - 108.0 MHz, RDS AM Tuning Frequency Range 522/530 kHz - 1611/1710 kHz Preset Channel 40

Others
Setup Mic Universal Port RI RS232 USB Ethernet IR Input/Output 12 V Trigger Out 1 1 1 1 1 (Front) 1 2/1 3

Specifications and features are subject to change without notice.

En

87

Video Resolution Chart

The following tables show how video signals at different resolutions are output by the AV receiver. NTSC/PAL : Output
Output HDMI 4K*2 1080p 1080i 720p 480i/576i Component 1080p 1080i 720p 480i/576i Composite 480i/576i PC IN (Analog RGB)*1

Input HDMI

1080p/24

1080p

1080i

720p

480p/576p 480i/576i

480p/576p

480p/576p

Composite 480i/576i

Input HDMI

Output Component 1080p 1080i 1080p 1080i 720p 480p/576p 480i/576i

720p

480p/576p 480i/576i

Component

1080p 1080i 720p 480p/576p 480i/576i

Composite

480i/576i

PC IN (Analog RGB)*1
*1 *2

Available resolutions: [640 480 60 Hz], [800 600 60 Hz], [1024 768 60 Hz], [1280 1024 60 Hz] Available resolutions: [3840 2160 24/25/30 Hz]

En

88

Memo

En

89

Memo

En

90

Memo

En

91

Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/ Integra Division of ONKYO CHINA PRC 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 Integra Division of ONKYO SOUND & VISION CORPORATION 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8163

En
Y1101-1

SN 29400656
(C) Copyright 2011 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.

* 2 9 4 0 0 6 5 6 *