Lm181e04 B3

Download as pdf or txt
Download as pdf or txt
You are on page 1of 28

LM181E04-B3 Liquid Crystal Display

Product Specification

SPECIFICATION FOR APPROVAL

( (

) Preliminary Specification ) Final Specification

Title
BUYER MODEL Philips

18.1 SXGA TFT LCD


SUPPLIER *MODEL SUFFIX LG.Philips LCD Co., Ltd. LM181E04 B3

*When you obtain standard approval, please use the above model name without suffix

SIGNATURE /

DATE

APPROVED BY S. W.LEE / G.Manager REVIEWED BY

DATE

G.T. Kim / Manager PREPARED BY

B.C.SONG/ Engineer

Please return 1 copy for your confirmation with your signature and comments.

Product Engineering Dept. LG. Philips LCD Co., Ltd

Ver 0.0

JUNE 01, 2001

1 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

CONTENTS
NO. 1 2 3 3-1 3-2 3-3 3-4 3-5 3-6 4 5 6 7 7-1 7-2 8 8-1 8-2 9 COVER CONTENTS RECORD OF REVISIONS GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS ELECTRICAL CHARACTERISTICS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERANCE POWER SEQUENCE OPTICAL SPECIFICATIONS MECHANICAL CHARACTERISTICS RELIABILITY INTERNATIONAL STANDARDS SAFETY EMC PACKING DESIGNATION OF LOT MARK PACKING FORM PRECAUTIONS ITEM Page 1 2 3 4 5 6 6 8 12 13 14 15 16 20 23 24 24 24 25 25 25 26

Ver 0.0

JUNE 01, 2001

2 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

RECORD OF REVISIONS
Revision No Ver 0.0 Date June 01, 2001 Page Description First Draft, Preliminary Specifications

Ver 0.0

JUNE 01, 2001

3 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 1. General Description


The LM181E04 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. This TFT-LCD has a 18.1 inch diagonal measured active display area with SXGA resolution(1024 vertical by 1280 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16M colors with FRC. The LM181E04 has been designed to apply the interface method that enables low power, high speed,low EMI. FPD Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip. The LM181E04 is intended to support applications where thin thickness,wide viewing angle, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LM181E04 characteristics provide an excellent flat panel display for office automation products such as monitors.
G1

Gate Driver Circuit

LVDS
pair #1

Timing Controller LVDS 1 Chip


CN1
(30pin)

TFT - LCD Panel


(1280
G1024

RGB

1024 pixels)

LVDS
pair #2

+12V
Vcc

S1

S1280

RGB

Power Circui t Block


CN2 (4pin) CN3 (4pin)

Source Driver Circuit Back-light Assembly (4CCFL)

General Features
Active screen size Outline Dimension Pixel Pitch Pixel Format Display Colors Luminance, white Power Consumption Weight Display operating mode Surface treatments Ver 0.0 18.1 inch (45.97cm) diagonal 412.5(H) x 333.0(V) x 21.5(D) mm(Typ.) 0.2805 mm x 0.2805 mm 1280 horiz. By 1024 vert. Pixels RGB stripe arrangement 16.2M colors 250 cd/m2(Typ. Center 1 point) Total 26.64 Watts(Typ.), (5.2Watts @Vcc, 21.44 Watts @250cd/ 2500g (Typ.) Transmissive mode, normally black Hard coating (3H), Anti-glare treatment of the front polarizer, Haze(13%) JUNE 01, 2001 4 / 28 [Lamp])

LM181E04-B3 Liquid Crystal Display

Product Specification 2. Absolute Maximum Ratings


The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS Parameter Power Supply Input Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity Symbol VCC TOP TST HOP HST Values Min. 0.3 0 20 10 10 Max. 13.2 50 60 90 90 Units V dc %RH %RH Notes At 25 1 1 1 1

Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 C Max, and no condensation of water.

90% 60 60% Humidity [(%) RH] 50 Wet Bulb Temperature [C] 40 40% 30 20 10 0 10% Storage

Operation

-20

10

20

30

40

50

60

70

80

Dry Bulb Temperature [C]

Ver 0.0

JUNE 01, 2001

5 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3. Electrical Specifications 3-1. Electrical Characteristics


The LM181E04 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by an inverter. The inverter is an external unit to the LCD. Table 2. ELECTRICAL CHARACTERISTICS Parameter MODULE : Power Supply Input Voltage Power Supply Input Current Differential Impedance Power Consumption Rush Current LAMP for each CCFL: Operating Voltage Operating Current Established Starting Voltage at 25 C at 0 C Operating Frequency Discharge Stabilization Time Power Consumption Life Time Symbol Values Min. 11.2 90 Typ. 12.0 0.43 100 5.2 3.1 Max. 12.6 0.80 110 9.6 4.8 Units Notes

IRUSH VBL IBL VS f BL TS PBL

VCC ICC Zm PC

V(DC) A ohm Watts A VRMS mARMS VRMS VRMS kHz Minutes Watts Hrs

1 2 1 3 4 5 6 7 8 9 10 11

780 680 650 (@9.0mA) (@8.0m) (@4.0mA) 9.0 8.0 4.0 45 30,000 60 21.44 1000 1300 80 3 23.60 -

Notes : 1. The values specified are measured under of VCC=12.0V, 25 C,fV=60Hz condition. 2. This value is for impedance matching between LVDS TX and the mating connector of the LCD. 3. The duration of rush current is about 1.0ms. 4. The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter(no lighting, flicker, etc) never occurs. When you confirm it, the LCD Assembly should be operated in the same condition as installed in you instrument. 5. The variance of the voltage is 10%. 6. This value is current measured at the ground terminal of the lamp. 7. The voltage above VS should be applied to the lamps for more than 1 second for start-up. Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.

Ver 0.0

JUNE 01, 2001

6 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

8. The output of the inverter must have symmetrical (negative and positive) voltage waveform and symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 9. Let s define the luminance of the lamp after being lighted for 5 minutes as 100%. TS is the time required for the luminance of the center of the lamp to be not less than 95%. The used lamp current is lamp typical current. 10. The lamp power consumption shown above does not include loss of external inverter. The value is measured at the condition of typical lamp current. 11. The life time is determined as the time at which luminance of the lamp is 50% compared to that of initial value at the typical lamp current on condition of continuous operating at 25 2 C. Do not attach a conducting tape to lamp connecting wire. If a conducting tape is attached to the lamp wire, TFT-LCD Module has a low luminance and the inverter has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.

Ver 0.0

JUNE 01, 2001

7 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-2. Interface Connections


Interface chip must be used LVDS, part No. DS90CF383MTD(Tx, Nation Semiconductor) or compatible. This LCD employs a interface connection, a 30 pin connector is used for the module electronics interface. Two 4pin connectors are used for the integral backlight system. The electronics interface connector is a model KN07K-30S-1H manufactured by HIROSE. The pin configuration for the connector is shown in the table 3 and the signal mapping with LVDS transmitter is shown in the table 5.

Table 3. MODULE CONNECTOR PIN CONFIGURATION(LVDS) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Symbol Vcc Vcc Vcc Vcc GND GND GND GND RO0M RO0P RO1M RO1P RO2M RO2P ROCLKM ROCLKP RO3M RO3P GND RE0M RE0P RE1M RE1P RE2M RE2P RECLKM RECLKP RE3M RE3P GND Description Power Supply Input Voltage Power Supply Input Voltage Power Supply Input Voltage Power Supply Input Voltage Ground Ground Ground Ground Minus signal of odd channel 0 (LVDS) Plus signal of odd channel 0 (LVDS) Minus signal of odd channel 1 (LVDS) Plus signal of odd channel 1 (LVDS) Minus signal of odd channel 2 (LVDS) Plus signal of odd channel 2 (LVDS) Minus signal of odd clock channel (LVDS) Plus signal of odd clock channel (LVDS) Minus signal of odd channel 3 (LVDS) Plus signal of odd channel 3 (LVDS) Ground Minus signal of even channel 0 (LVDS) Plus signal of even channel 0 (LVDS) Minus signal of even channel 1 (LVDS) Plus signal of even channel 1 (LVDS) Minus signal of even channel 2 (LVDS) Plus signal of even channel 2 (LVDS) Minus signal of even clock channel (LVDS) Plus signal of even clock channel (LVDS) Minus signal of even channel 3 (LVDS) Plus signal of even channel 3 (LVDS) Ground

First data

Second data

Ver 0.0

JUNE 01, 2001

8 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-2. Interface Connections

#1

#30

KN07K-30S-H (HIROSE) #1 #30

Rear view of LCM Notes: 1. All GND(ground) pins should be connected together and should also be connected to the LCDs metal frame. 2. All VCC(power input) pins should be connected together. 3.Mating connector is FI-X30H(JAE)

Ver 0.0

JUNE 01, 2001

9 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

The backlight interface connector is a model BHR-04VS-1, manufactured by JST. The mating connector part number is SM02(12)B-BHS-1-TB or equivalent. The pin configuration for the connector is shown in the table 4. Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION Pin 1 2 3 4 Symbol HV HV NC LV Description High Voltage for lamp High Voltage for lamp No Connection Low Voltage for lamp 1,2 Notes 1 1

Notes : 1. The high voltage side terminal is colored pink. The low voltage side terminal is white 2. The backlight ground should be common with LCD metal frame.

The below is block diagram for pin configuration of lamp connector. CN2 Lamp 1 Lamp 2 1 2 3 4

CN3 Lamp 3 Lamp 4 1 2 3 4

Ver 0.0

JUNE 01, 2001

10 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification
Table 5. REQUIRED SIGNAL ASSIGNMENT FOR Flat Link (TI:SN75LVDS83) Transmitter
Pin# Pin Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VCC D5 D6 D7 GND D8 D9 D10 VCC D11 D12 D13 GND D14 D15 D16 VCC D17 D18 D19 GND D20 D21 D22 D23 VCC D24 D25 Require Signal Power Supply for TTL Input TTL Input(R7) TTL Input(R5) TTL Input(G0) Ground pin for TTL TTL Input(G1) TTL Input(G2) TTL Input(G6) Power Supply for TTL Input TTL Input(G7) TTL Input(G3) TTL Input(G4) Ground pin for TTL TTL Input(G5) TTL Input(B0) TTL Input(B6) Power Supply for TTL Input TTL Input(B7) TTL Input(B1) TTL Input(B2) Ground pin for TTL Input TTL Input(B3) TTL Input(B4) TTL Input(B5) TTL Input(RSVD) Power Supply for TTL Input TTL Input(HSYNC) TTL Input(VSYNC) Pin# 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Pin Name GND D26 TxCLKIN PWR DWN PLL GND PLL VCC PLL GND LVDS GND TxOUT3+ TxOUT3TxCLKOUT+ TxCLKOUTTxOUT2+ TxOUT2LVDS GND LVDS VCC TxOUT1+ TxOUT1TxOUT0+ TxOUT0LVDS GND D27 D0 D1 GND D2 D3 D4 Require Signal Ground pin for TTL TTL Input(R7) TTL Level clock Input Power Down Input Ground pin for PLL Power Supply for PLL Ground pin for PLL Ground pin for LVDS Positive LVDS differential data output3 Negative LVDS differential data output3 Positive LVDS differential clock output Negative LVDS differential clock output Positive LVDS differential data output2 Negative LVDS differential data output2 Ground pin for LVDS Power Supply for LVDS Positive LVDS differential data output1 Negative LVDS differential data output1 Positive LVDS differential data output0 Negative LVDS differential data output0 Ground pin for TTL TTL Input(R6) TTL Input(R0) TTL Input(R1) Ground pin for TTL TTL Input(R2) TTL Input(R3) TTL Input(R4)

Notes : Refer to LVDS Transmitter Data Sheet for detail descriptions.

Ver 0.0

JUNE 01, 2001

11 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-3. Signal Timing Specifications


This is the signal timing required at the input of the LVDS Transmitter. All of the interface signal timing should be satisfied with the following specifications for it s proper operation. Table 6. TIMING TABLE ITEM Dclk Period Frequency Hsync Period Frequency Width Period Vsync Frequency Width Horizontal Address Time Horizontal Back Porch DE (Data Enable) Horizontal Front Porch Horizontal Blank Time Vertical Address Time Vertical Back Porch Vertical Front Porch Vertical Blank Time SYMBOL tCLK fCLK tHP fHP tWH tVP fV tWV tHV tHBP tHFP tVV tVBP tVFP MIN 18.52 844 63.98 16 1066 60 2 640 16 16 48 1024 2 1 5 TYP. 18.52 54 844 63.98 56 1066 60 3 640 124 24 204 1024 38 1 42 MAX. 54 640 -

UNIT ns MHz tCLK KHz tCLK tHP Hz tHP

NOTES

tCLK

1024 -

tHP

Notes : Input data shall be latched at the falling edge of DCLK.

Ver 0.0

JUNE 01, 2001

12 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-4. Signal Timing Waveforms


0.7Vcc 0.3Vcc

Hsync, Vsync, DE, Data

DCLK

tCLK

0.5 Vcc

Valid data

Invalid data
First(Odd) data

Pixel 0,0

Pixel 2,0

Invalid data

Valid data

Invalid data
Second(Even) data

Pixel 1,0

Pixel 3,0

Invalid data

DE(Data Enable)

HSync

tWH tHBP

tHP tHV tHFP

DE(Data Enable) tVP tWV VSync tVBP tVV tVFP

DE(Data Enable)

Ver 0.0

JUNE 01, 2001

13 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-5. Color Input Data Reference


The brightness of each primary color(red,green and blue) is based on the 8-bit gray scale data input for the color ; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.

Table 7. COLOR DATA REFERENCE

Color

Input Color Data Green Red Blue MSB LSBMSB LSBMSB LSB R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
0 1 0 0 0 1 1 1 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 1 0 0 0 1 1 1 0 0 1 : 0 1 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 00 01 10 00 10 01 11 11 00 01 00 :: 01 00 01 00 00 00 :: 10 10 10 00 00 00 :: 00 00 00 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : 0 0 0 0 0 1 : 0 1 1 0 0 0 : 0 0 0 00 00 01 10 11 10 01 11 00 00 00 :: 00 00 00 00 01 00 :: 01 00 01 00 00 00 :: 10 10 10 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 1 1 0 0 0 1 1 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 0 1

Black 0 Red(255) 1 Green(255) 0 Basic Blue(255) 0 Colors Cyan 0 Magenta 1 Yellow 1 White 1 Red(000) Dark 0 Red(001) 0 Red(002) 0 Red : : : : :: Red(253) 1 Red(254) 1 Red(255) Bright 1 Green(000) Dark 0 Green(001) 0 Green(002) 0 Green : : : : : : Green(253) 0 Green(254) 0 Green(254)Bright 0 Blue(000) Dark 0 Blue(001) 0 Blue(002) 0 Blue : : : : : : Blue(253) 0 Blue(254) 0 Blue(255)Bright 0

Ver 0.0

JUNE 01, 2001

14 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 3-6. Power Sequence

90% Power supply for LCD Vcc 10%

90% 10%

T1 Interface signal 0V

T2 Valid data T3 T4

T5

T6

T7

Power for LAMP

OFF

Lamp on

OFF

Parameter T1 T2 T3 T4 T5 T6 T7

Min. 0.01 200 200 0.01 0.01 3

Values Typ. -

Max. 10 50 20 10 -

Units ms ms ms ms ms ms s

Notes : 1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply for LCD VCC to 0V. 3. Lamp power must be turn on after power supply for LCD and interface signals are valid.

Ver 0.0

JUNE 01, 2001

15 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 4. Optical Specifications


Optical characteristics are determined after the unit has been ON and stable for approximately 30 minutes in a dark environment at 25 C. The values specified are measured at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0 . FIG. 1 presents additional information concerning the measurement equipment and method. FIG. 1 Optical Characteristic Measurement Equipment and Method Optical Stage(x,y) LCD Module Field = 1 Pritchard PR880 or equivalent 50Cm Table 8. OPTICAL CHARACTERISTICS Parameter Contrast Ratio Surface Luminance, white Luminance Variation Response Time Rise Time Decay Time Symbol CR LWH WHITE Tr TrR TrD (Ta=25 C, VCC=12.0V, fV=60Hz Dclk=54MHz, IBL=8mArms) Values Min. 200 200 0.599 0.308 0.269 0.560 0.114 0.063 0.283 0.299 70 70 60 70 JUNE 01, 2001 Typ. 300 250 17 18 0.629 0.338 0.299 0.590 0.144 0.093 0.313 0.329 80 80 80 80 2.0 2.2 Max. 1.30 22 23 0.659 0.368 0.329 0.620 0.174 0.123 0.343 0.359 4.0 -18.0 degree 5 ms cd/m2 Units Notes 1 2 3 4

CIE Color Coordinates Red Green Blue White Viewing Angle x axis, right(=0 ) x axis, left (=180 ) y axis, up (=90 ) y axis, down (=270 ) Crosstalk Ratio Flicker Gamma value Ver 0.0

xR xG yG xB yB xW yW
x x y y yR

% dB

6 7 8 16 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

Notes : 1. Contrast Ratio(CR) is defined mathematically as : Surface Luminance with all white pixels Contrast Ratio = Surface Luminance with all black pixels Contrast ratio shall be measured at the center point of the display(location 1 of Fig 2) 2. Surface luminance is measured at the center point of the display (location 1 of Fig 2) 3. The variation in surface luminance , WHITE is defined as : WHITE = Maximum(LON1,LON2, .. LON5) Minimum(LON1,LON2, .. LON5) Where, LON1,LON2,LON3,LON4 and LON5 are surface luminance values measured at each location shown Fig 2. 4. Response time is the time required for the display to transition from black to white(Rise Time, TrR) and from white to black(Decay Time, TrD). For additional information see FIG 3. 5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 4. 6. Cross talk shall be measured at the V and H position. For more information see Fig 5. Luminance at pattern A - Luminance at pattern B Contrast Ratio = Luminance at pattern B 7. Flicker shall be measured at the center location. Test pattern : Pixel pattern(Dot Pattern) Background RGB gray(0, 0, 0) Foreground RGB gray(127, 127, 127) AC(at 30Hz) Flicker = 20log DC Level
Voltage

X 100(%)

(dB)

DC Time

AC

Ver 0.0

JUNE 01, 2001

17 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

8. Relative Luminance as gray level. Gray Level L0 L31 L63 L95 L127 L159 L191 L223 L255 Luminance(%) (Min.) 0.34 3.20 8.06 16.76 30.72 55.22 100 Luminance(%) (Typ.) 0.32 1.77 5.12 12.17 21.95 34.34 50.62 72.48 100 Luminance(%) (Max.) 1.30 5.35 11.02 21.03 35.84 51.92 70.62 89.93 100

FIG. 2 Measurement Location

<measuring point for luminance variation> H A

<measuring point for surface luminance> H H/2

B V

2 1 4

V/2 V

A : H/4 mm B : V/4 mm H : 359.040 mm V : 287.232 mm @ H,V : Active Area

Active Area

Ver 0.0

JUNE 01, 2001

18 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

FIG. 3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for black and white .

TrR
100 90

TrD

Optical Response
10 0

black

white

black

FIG. 4 Viewing angle <Dimension of viewing angle range>

= 90
(12: 00)

= 0
yu z

= 180
(9: 00)

xl

= 0
(3: 00)

xr

T LD FT C MD L OUE

z'

yd

= 270
(6: 00)

Ver 0.0

JUNE 01, 2001

19 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification

FIG. 5 Crosstalk

A1 (640,128)

A2 (640,128)

B1 (1120,512)

B2 (1120,512)

Pattern 1
Background : Mid-gray

Pattern 2
Window : Black/White Window Size : 50% Background : Mid-gray

Ver 0.0

JUNE 01, 2001

20 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 5. Mechanical Characteristics


Table 9. provides general mechanical characteristics for the model LM181E04. Please refer to Fig 5,6 regarding the detailed mechanical drawing of the LCD. Table 9. OPTICAL CHARACTERISTICS Horizontal Outside dimensions Vertical Depth Bezel area Active display area Weight(approximate) Surface Treatment Horizontal Vertical Horizontal Vertical 2500g(Typ.), 412.5 0.5mm 333.0 0.5mm 21.5 0.3mm 363.5 0.5mm 292.0 0.5mm 359.040mm 287.232mm 2625g(Max.)

Hard coating(3H) Anti-glare treatment of the front polarizer Haze(13%)

Ver 0.0

JUNE 01, 2001

21 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification
FIG. 5 FRONT VIEW

Ver 0.0

JUNE 01, 2001

22 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification
FIG. 6 REAR VIEW

Ver 0.0

JUNE 01, 2001

23 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 6. Reliability

No. 1 2 3 4 5

Test Item High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test Vibration test (non-operating) Ta= 60 C Ta= -20 C

Conditions 240h 240h 240h

Ta= 50 C 50%RH Ta= 0 C 240h

1. Sinusoidal Vibration 1.0G zero to peak. 10 to 500 Hz, 0.5 oct/min sweep rate. 10 to 500, 10Hz, one Sweep along each axis. 2. Random Vibration 0.002 G2/Hz, 10 to 500Hz, nominal 1 GRMS. One Hour for each of the three axis. 1. Half sine wave shock: 120G peak, half sine pulse, 2ms pulse duration. Testing shall consist of one shock in each direction in each axis, for a total of 6shock inputs.(1 time) 2. Square Wave Shock 30G peak acceleration, 180 inches/sec velocity change. There shall be one shock in each direction in each axis, for a total of 6 shock inputs.(1 time)

Shock test (non-operating)

Altitude Non-operating storage / shipment 0 - 40,000 feet(12,192m)

{ Result Evaluation Criteria } There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition.

Ver 0.0

JUNE 01, 2001

24 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 7. International Standards 7-1. Safety


a) UL 1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995. Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. b) CAN/CSA C22.2 No. 950-95 Third Edition, Canadian Standards Association, Jan. 28, 1995. Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. c) EN 60950 : 1992+A1: 1993+A2: 1993+A3: 1995+A4: 1997+A11: 1997 IEC 950 : 1991+A1: 1992+A2: 1993+A3: 1995+A4: 1996 European Committee for Electrotechnical Standardization(CENELEC) EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business Equipment.

7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. American National Standards Institute(ANSI), 1992 b) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. International Special Committee on Radio Interference (Standards apply by CISPR22 class B). c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. European Committee for Electrotechnical Standardization (CENELEC), 1998

Ver 0.0

JUNE 01, 2001

25 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 8. Packing 8-1. Designation of Lot Mark


a) Lot Mark A B C D E F G H I J K L M

A,B,C : SIZE D : YEAR E : MONTH F,G : PANEL CODE H : ASSEMBLY CODE I,J,K,L,M : SERIAL NO.

Note: 1. YEAR YEAR Mark 2. MONTH MONTH Mark 3. Serial No. Serial No. Mark 1 ~ 99999 00001 ~ 99999 100000 ~ A0001 ~ A9999,, Z9999 Jan. 1 Feb. Mar. Apr. May. Jun. 2 3 4 5 6 Jul. 7 Aug. Sep. 8 9 Oct. Nov. Dec. 10 11 12 97 7 98 8 99 9 2000 0 2001 1 2002 2 2003 2004 2005 3 4 5 2006 2007 6 7

b) Location of Lot Mark Serial NO. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.

8-2. Packing Form


a) Package quantity in one box : 5 pcs b) Box Size : 530mm 307mm 453mm

Ver 0.0

JUNE 01, 2001

26 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 9. PRECAUTIONS


Please pay attention to the followings when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS


(1) You must mount a module using holes arranged in four corners. (2) You should consider the mounting structure so that uneven force(ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength.

9-2. OPERATING PRECAUTIONS


(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V= 200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference.

Ver 0.0

JUNE 01, 2001

27 / 28

LM181E04-B3 Liquid Crystal Display

Product Specification 9-3. ELECTROSTATIC DISCHARGE CONTROL


Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don t touch interface pin directly.

9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE


Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5 C and 35 C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.

9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM


(1) When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. Please carefully peel off the protection film without rubbing it against the polarizer. (3) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarizer after the protection film is peeled off. (4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.

Ver 0.0

JUNE 01, 2001

28 / 28

You might also like