Digital 16 Marks.
Digital 16 Marks.
Digital 16 Marks.
(a) Prove that (x1+x2).(x1. x3+x3) (x2 + x1.x3) =x1x2 (b) Simplify using K-map to obtain a minimum POS expression: (A + B+C+D) (A+B+C+D) (A+B+C+D) (A+B+C+D) (A+B+C+D) (A+B+C+D) 2. Reduce the following equation using Quine McClucky method of minimization F (A,B,C,D) = m(0,1,3,4,5,7,10,13,14,15) 3. (a) State and Prove idempotent laws of Boolean algebra. (b) using a K-Map ,Find the MSP from of F= (0,4,8,12,3,7,11,15) +_d(5) 4. Using a K-Map, Find the MSP form of F= (0-3, 12-15) + _d (7, 11) 5. (a) Simplify the following using the Quine McClusky minimization technique D = f(a,b,c,d) = (0,1,2,3,6,7,8,9,14,15).Does Quine McClusky take care of dont care conditions? In the above problem, will you consider any dont care conditions? Justify your answer (b) List also the prime implicants and essential prime implicants for the above case 6. (a) Determine the MSP and MPS focus of F= (0, 2, 6, 8, 10, 12, 14, 15) (b) State and Prove Demorgans theorem 7. Determine the MSP form of the Switching function F = ( 0,1,4,5,6,11,14,15,16,17,20- 22,30,32,33,36,37,48,49,52,53,56,63) 8. (a) Determine the MSP form of the Switching function F( a,b,c,d) = (0,2,4,6,8) + d(10,11,12,13,14,15) (b) Find the Minterm expansion of f(a,b,c,d) = a(b+d) + acd 9. Simplify the following Boolean function by using the Tabulation Method F= _ (0, 1, 2, 8, 10, 11, 14, 15) 10. Find a Min SOP and Min POS for f = bcd + bcd + acd + abc + abcd 11. Find an expression for the following function usingQuine McCluscky method F= (0, 2, 3,5,7,9,11,13,14,16,18,24,26,28,30) 12. State and Prove the theorems of Boolean algebra with illustration 13. Find the MSP representation for F(A,B,C,D,E) = m(1,4,6,10,20,22,24,26) + d (0,11,16,27) using K-Map method, Draw the circuit of the minimal expression using only NAND gates 14. (a) Show that if all the gates in a two level AND-OR gate networks are replaced by NAND gates the output function does not change (b) Why does a good logic designer minimize the use of NOT gates? 15. Simplify the Boolean function F(A,B,C,D) = m (1,3,7,11,15) + d (0,2,5) .if dont care conditions are not taken care, What is the simplified Boolean function .What are your comments on it? Implement both circuits 16. (a) Show that if all the gate in a two level OR-AND gate network are replaced by NOR gate, the output function does not change. (b) Implement Y = (A+C) (A+D) ( A+B+C) using NOR gates only 17. (a) Show that the NAND operation is not distributive over the AND operation (b) Find a network of AND and OR gate to realize f(a,b,c,d) = m (1,5,6,10,13,14) 18. What is the advantages of using tabulation method? Determine the prime implicants of the following function using tabulation method F( W,X,Y,Z) = (1,4,6,7,8,9,10,11,15) 19. Given the following Boolean function F= AC + AB + ABC + BC Express it in sum of minterms & Find the minimal SOP expression. 20. Explain the operation of 3 I/P TTL NAND Gate with required diagram and truth table. 21. Explain the operation of CMOS NAND and NOR Gate with the circuits and truth table. UNIT-II COMBINAL CIRCUITS 1. Implement the switching function F= (0,1,3,4,7) using a 4 input MUX and explain 2. Explain how will build a 64 input MUX using nine 8 input MUXs
3. Implement the switching function F= (0,1,3,4,12,14,15) using an 8 input MUX 4. Explain how will build a 16 input MUX using only 4 input MUXs 5. Explain the operation of 4 to 10 line decoder with necessary logic diagram 6. Design full adder and full sub tractor. 7. Design a 4 bit magnitude comparator to compare two 4 bit number 8.Construct a combinational circuit to convert given binary coded decimal number into an Excess 3 code for example when the input to the gate is 0110 then the circuit should generate output as 1001 9. Using a single 7483, draw the logic diagram of a 4 bit adder/sub tractor 10. Realize a Binary to BCD conversion circuit starting from its truth table 11. Design a combinational circuit which accepts 3 bit binary number and converts its equivalent excess 3 codes 12. Explain carry look ahead adder. 13. Draw and explain BCD adder. UNIT-III SEQUENTIAL CIRCUITS 1. Explain the operation of JK and clocked JK flip-flops with suitable diagrams 2.Draw the state diagram of a JK flip- flop and D flip flop 3.Design and explain the working of a synchronous mod 3 counter 4.Design and explain the working of a synchronous mod 7 counter 5. Design a synchronous counter with states 0,1, 2,3,0,1 . Using JK FF 6. Using SR flip flops, design a parallel counter which counts in the sequence 000,111,101,110,001,010,000 . 7.Using JK flip flops, design a parallel counter which counts in the sequence 000,111,101,110,001,010,000 . 8.Draw and explain Master-Slave JK flip-flop. 9.Draw as asynchronous 4 bit up-down counter and explain its working 10.Using D flip flop ,design a synchronous counter which counts in the sequence 000, 001, 010, 011, 100, 1001,110,111,000 11.Design a binary counter using T flip flops to count in the following sequences: (i) 000,001,010,011,100,101,110,111,000 (ii) 000,100,111,010,011,000 12.Design a 3 bit binary Up-Down counter 13. Draw and explain the operation of four bit Johnson counter. 14. Analyze the given shown in fig. obtains the state table and state diagram and determine the function of the circuit. X1 X2 J CLK K 15. Minimize the following state table. PRESENT NEXT STATE STATE X=0 X=1 A A D B C D C B A D D A E D A F D A Z2 Z1
G h
D D
A C
1 1
1 1
16.Determine a minimal state table equivalent furnished below. PRESENT NEXT STATE, STATE OUTPUT (Z) X=0 X=1 1 1,0 1,0 2 1,1 6,1 3 4,0 5,0 4 1,1 7,0 5 2,0 3,0 6 4,0 5,0 7 2,0 3,0
UNIT-IV MEMORY DEVICES 1.Draw a RAM cell and explain its working. 2.Write short notes on (i) RAM (ii) Types of ROMs. 3. List the PLA program table for BCD to Excess -3-code convertor circuits and show its implementation for any two output functions. 4. Generate the following Boolean functions with PAL with 4inputs and 4outputs Y3=ABCD+ABCD+ABCD+ABCD Y2=ABCD+ABCD+ABCD Y1=ABC+ABC+ABC+ABC Y0=ABCD. 5. Implement the following functions using PLA. F1=m(1,2,4,6); F2=m(0,1,6,7) F3=m(2,6) 6. Implement the given functions using PROM and PAL F1=m(0,1,3,5,7,9); F2=m(1,2,4,7,8,10,11) 7. Implement the given functions using PAL, PLA F1=m(0,1,2,4,6,7); F2=m(1,3,5,7); F3=m(0,2,3,6) 8. Draw the block diagram of a PLA device and briefly explain each block. 9. Design a 16 bit ROM array and explain the operation 10. Write short note on Field Programmable Gate Array (FPGA). UNIT-V SYNCHRONOUS AND ASYNCHRONOUS SEQUENTIAL CIRCUITS 1. What is the objective of state assignment in asynchronous circuit? Give hazard free realization for the following Boolean function f(A,B,C,D) = m(0,2,6,7,8,10,12) 2. Summarize the design procedure for asynchronous sequential circuit Discuss on Hazards and races 3. Develop the state diagram and primitive flow table for a logic system that has 2 inputs,x And y and an output z. And reduce primitive flow table. The behavior of the circuit is stated as follows. Initially x=y=0. Whenever x=1 and y = 0 then z=1, whenever x = 0 and y = 1 then z = 0.When x=y=0 or x=y=1 no change in z ot remains in the previous state. The logic system has edge triggered inputs with out having a clock .the logic system changes state on the rising edges of the 2 inputs. Static input values are not to have any effect in changing the Z output 4. Design an asynchronous sequential circuit with two inputs X and Y and with one output Z. Whenever Y is 1, input X is transferred to Z.When Y is 0,the output does not change for any change in X. 5. Obtain the primitive flow table for an asynchronous circuit that has two inputs x,y and one output Z. An output z =1 is to occur only during the input state xy = 01 and then if the only if the input state xy =01 is preceded by the input sequence.
6. A pulse mode asynchronous machine has two inputs. It produces an output whenever two consecutive pulses occur on one input line only .The output remains at 1 until a pulse has occurred on the other input line. Draw the state table for the machine. 7. Construct the state diagram and primitive flow table for an asynchronous network that has two inputs and one output. The input sequence X1X2 = 00,01,11 causes the output to become 1.The next input change then causes the output to return to 0.No other inputs will produce a 1 output. 8. Discuss on the different types of Hazards that occurs in asynchronous sequential circuits. 9. Write short note on races and cycles that occur in fundamental mode circuits. 10. Define the following terms: a. Critical race b. non-critical race. c. hazard d. flow table. 11. Draw the fundamental mode asynchronous circuit and explain in details. 12. For the state diagram shown, design a sequential circuit using JK flip-flop 0/0 0/1 d 1/0 0/1 c 0/1 a 1/1 b
1/0
13.Reduce the following state diagram. 0/0 a 0/0 1/0 b g 1/0 1/1 d 0/0 f 1/1 0/0 e 1/1 0/0 1/0 0/0 c 0/0
1/1