Close Window

Assessment System Exam Viewer - CCENT Practice Certification Exam # 1 - CCNA Exploration: Accessing the WAN (Version 4.0)

Below you will find the assessment items as presented on the exam as well as the scoring rules associated with the item. Cisco Networking Academy content is copyrighted and the unauthorized posting, distribution or sharing of this exam content is prohibited. 1 What are two ways that TCP uses the sequence numbers in a segment? (Choose two.) to identify missing segments at the destination to reassemble the segments at the remote location to specify the order in which the segments travel from source to destination to limit the number of segments that can be sent out of an interface at one time to determine if the packet changed during transit Observable correctness of 1 response Description 1 point for Option 1, Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

4.3.3 TCP Retransmission Which three statements characterize UDP? (Choose three.) UDP provides connectionless, fast transport of data at Layer 4. UDP provides connection-oriented, fast transport of data at Layer 3. UDP relies on application layer protocols for error detection. UDP works well when an application does not need to guarantee delivery of data. UDP relies on IP for error detection and recovery. UDP provides sophisticated flow control mechanisms. Observable Description 1 point for Option 1, Option 3, Max Value 1

1 correctness of

response

Option 4 0 point for any other option

This item references content from the following areas: CCNA Exploration: Network Fundamentals

4.4.1 UDP - Low Overhead vs. Reliability

Refer to the exhibit. Host A sends a data packet to host B. What will be the addressing informa the data packet when it reaches host B?

Observabl e 1

Description

Max Value 1

correctness 1 point for Option 1 of response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Network Fundamentals

9.3.5 Ethernet Unicast, Multicast and Broadcast

Which layer of the OSI model defines logical addressing? application presentation session transport network data link Observable Description 1 point for Option 5 0 point for any other option Max Value 1

correctness of response

This item references content from the following areas: CCNA Exploration: Network Fundamentals

9.3.4 Another Layer of Addressing

Which device connects a local LAN to a geographically separate network? switch hub router bridge Description 1 point for Option 3 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

2.2.2 Wide Area Networks

Refer to the exhibit. Router1 receives packets addressed as follows: Source IP address: 192.168.1.88 Destination IP address: 172.16.0.3 Source MAC address: 00-11-12-7a-41-10 Destination MAC address: 00-11-5c-cc-a9-c0 Source Port: 1464 Destination Port: 23 Assuming that Router1 has not been configured with NAT, what will happen to the packets? The packets will be sent to the server because it is a server-based port. The packets will be sent to Switch2 and not leave the switch because the packets are local. The packets will be sent to the laptop host. The packets will be sent to Router1 and dropped because private addresses are not transmitted across Internet. The packets will be sent to Router2 and dropped because the server is not directly attached. Description 1 point for Option 4 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.2.5 Public and Private Addresses

Refer to the exhibit. If host 1 was to send an HTTP request to the web server that connects to Router2, wh of Layer 2 frame would be sent between Router1 and the ISP? a frame with a header that contains the port number of 80 a frame with a header and trailer, but no MAC addresses a frame with a header and a trailer that only contains IP addresses a frame with the host 1 MAC address as the source and Router1 MAC address as the destination a frame with the host 1 MAC address as the source and the server MAC address as the destination Observable 1 correctness of response Description 1 point for Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

7.3.5 Data Link Layer Protocols - The Frame

A company needs to connect an office router to a service provider to access a WAN. What device is neede connect the router to the ISP if the service provider supplies a T1 line for the connection? a CSU/DSU a cable modem a DSL router a DTE device an SLA device Description 1 point for Option 1 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas:

CCNA Exploration: Network Fundamentals

10.2.3 Making WAN Connections

Refer to the exhibit. A technician applies the configuration in the exhibit to an unconfigured router. To ve configuration, the technician issues the show running-config command in the CLI session with the router lines should the technician expect to see in the router output from the show running-config command? enable password class line console 0 password ccna enable secret cisco enable password class line console 0 password ccna enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0 enable password class line console 0 password ccna enable secret cisco enable password 7 14141E0A1F17 line console 0 password 7 020507550A enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0 enable password 7 14141E0A1F17 line console 0 password 7 020507550A Description 1 point for Option 5 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2.2 Limiting Device Access - Configuring Passwords and Using Banners

10

Refer to the exhibit. If host A sends an IP packet to host B, what will the destination address b frame when it leaves host A? DD:DD:DD:DD:DD:DD 172.168.10.99 CC:CC:CC:CC:CC:CC 172.168.10.65 BB:BB:BB:BB:BB:BB AA:AA:AA:AA:AA:AA Observable 1 Description Max Value 1

correctness 1 point for Option 5 of response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.4.5 Switching Function

11

Refer to the exhibit. What two facts can be determined from the output of the ping command (Choose two.) There was a destination unreachable error. The packet type was unknown. One packet timed out. The ping was interrupted. Four packets of data were successfully received.

The packet TTL was exceeded. Observable 1 correctness of response Description 1 point for Option 3, Option 5 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.6.5 ICMPv4 - The Protocol Supporting Testing and Messaging

12

Refer to the exhibit. The switches are in their default configuration. Host A needs to commu with host D, but host A does not have the MAC address for its default gateway. Which netw hosts will receive the ARP request sent by host A? only host D only router R1 only hosts A, B, and C only hosts A, B, C, and D only hosts B and C only hosts B, C, and router R1 Observable Description Max Value correctness of 1 point for Option 6 1 1 response 0 point for any other option This item references content from the following areas: CCNA Exploration: Network Fundamentals

9.7.2 The ARP Process - Destinations outside the Local Network

13

Refer to the exhibit. Which password will the administrator need to use on this device to ente privileged EXEC mode? Cisco class password cisco Observable Description correctness 1 point for Option 4 1 of response 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

11.2.2 The router ospf Command

14

Refer to the exhibit. Switch1 has only the following commands added to a default Cisco 2960 configuration: enable secret cisco line vty 0 4 password Kn0ckkn-cK login interface vlan 1 ip address 10.0.1.8 255.255.255.0 no shutdown

Assume that routing between networks is functioning properly and that Switch2 has been pro configured for remote access. What would the result be if the telnet 10.0.2.2 command is iss from Switch1 privileged mode? The following prompt would appear: User Access Verification Password: Switch2 would return a destination unreachable message to Switch1. Router1 would return a destination unreachable message to Switch1. The packet would be dropped. Observable 1 correctness of response Description 1 point for Option 4 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2.4 Configuring Interfaces What caused the following error message to appear?

15

01:11:12: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/8, putting Fa0 err-disable state 01:11:12: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0011.a0d4.12a0 on port FastEthernet0/8. 01:11:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, chan state to down 01:11:14: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to down

Another switch was connected to this switch port with the wrong cable. An unauthorized user tried to telnet to the switch through switch port Fa0/8. NAT was enabled on a router, and a private IP address arrived on switch port Fa0/8. A host with an invalid IP address was connected to a switch port that was previously u Port security was enabled on the switch port, and an unauthorized connection was ma switch port Fa0/8.

Observable 1 correctness of response

Description 1 point for Option 5 0 point for any other option

Max Value 1

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

2.5.1 Basic Switch Configuration

16 When configuring a switch to use SSH for virtual terminal connections, what is the purpose of the crypto generate rsa command? show SSH connected hosts disconnect SSH connected hosts create a public and private key pair show active SSH ports on the switch access the SSH database configuration Observable 1 correctness of response Description 1 point for Option 3 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

2.4.3 Configure Telnet and SSH

17

Which three statements are true about full-duplex operation on an Ethernet network? (C three.) There are no collisions in full-duplex mode. A dedicated switch port is required for each node. Hub ports are preconfigured for full-duplex mode. The host network card must detect the availability of the media before transmitting. The host network card and the switch port must both be in full-duplex mode. Observable Description 1 point for Option 1, Option 2, Option 5 0 point for any other option Max Value 1

correctness of response

This item references content from the following areas:

CCNA Exploration: Network Fundamentals

9.6.2 Ethernet - Using Switches

18

Refer to the exhibit. If all the switches have a default configuration, how many broadcast dom are in the network? 1 2 3 4 5 14 Observable 1 correctness of response Description 1 point for Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

5.2.2 Why Separate Hosts Into Networks? - Performance

19

Observable 1 correctness of response 2 Obs2 Title 3 Obs3 Title

Description See feedback.

Max Value 1 1 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

2.6.1 Lab: Topology Orientation and Building a Small Network 8.3.3 Unshielded Twisted Pair (UTP) Cable

20

Refer to the exhibit. The devices have been configured with static IP addresses as shown. All can communicate with each other but none of the hosts can communicate with the server. Wh the cause of this problem? The IP address that is assigned to the server is in an incorrect subnet. The IP address that is assigned to the server is a broadcast address. The IP address that is assigned to the server is a network address. The switch to which the server is connected has not been assigned an IP address. The RouterB LAN interface is incorrectly addressed in the RouterA LAN subnet. Observable Description correctness 1 point for Option 1 1 of response 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.5.6 Determining Valid Addresses for Hosts

21 A network host has the IP address 10.250.206.55/20. How many more network devices can be added to th same subnetwork? 253 509 1021 2045 4093 Observable 1 correctness of response Description 1 point for Option 5 0 point for any other option Max Value 1

This item references content from the following areas:

CCNA Exploration: Network Fundamentals

6.5.2 Subnetting - Dividing Networks into Right Sizes

22 Which type of Network Address Translation allows a host on a public network consistent access to a spec private inside host? port-based NAT static NAT dynamic NAT NAT overload Observable 1 correctness of response Description 1 point for Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Accessing the WAN

7.2.4 Configuring Static NAT

23

Refer to the exhibit. Which two addresses are "inside global" addresses? (Choose two.) 192.168.7.3 64.100.1.5 198.133.219.35

192.168.7.2 198.133.219.44 64.100.1.4 192.168.7.1 Observabl e 1 Description Max Value 1

correctness 1 point for Option 3, Option 5 of response 0 points for any other option

This item references content from the following areas: CCNA Exploration: Accessing the WAN

7.2.6 Configuring NAT Overload

24

Which addresses are valid host IP addresses given the subnet mask 255.255.255.248? (C three.) 192.168.200.87 194.10.10.104 223.168.210.100 220.100.100.154 200.152.2.160 196.123.142.190 Observable Description 1 point for Option 3, Option 4, Option 6 0 point for any other option Max Value 1

correctness of response

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.5.1 Basic subnetting

25

The router receives a packet with the destination address of 172.16.30.79. To which subn does this packet belong? 172.16.30.0/22 172.16.30.64/22 172.16.30.76/22 172.16.28.0/22 172.16.28.56/22 172.16.0.0/22

Observable correctness of 1 response

Description 1 point for Option 4 0 points for any other option

Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.4.2 ANDing - What Is In Our Network?

26

Refer to the exhibit. What is the broadcast address for the subnetwork on which host A res 10.255.255.255 10.144.255.255 10.149.255.255 10.149.191.255 10.159.255.255 Observable 1 correctness of response Description 1 point for Option 5 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

6.2.2 Calculating Network, Hosts and Broadcast Addresses

27

Observable 1 correctness of response

Description See feedback.

Max Value 1

This item references content from the following areas: CCNA Exploration: Accessing the WAN

4.1.1 Why is Network Security Important? 4.1.2 Common Security Threats 4.1.3 Types of Network Attacks What can a network administrator modify on a router to specify the location from which Cisco IOS loads? (Choose two.) system ROM the startup configuration file

28

the system image file the configuration register value the NVRAM file system Observable 1 correctness of response Description 1 point for Option 2, Option 4 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.1.4 Router Boot-up Process

29

Which two items are required for initial configuration of Cisco routers if the IOS comma interface is used? (Choose two.) a crossover cable a rollover cable an RJ-15 to DB-9 adapter terminal emulation software router VTY port Observable Description 1 point for Option 2, Option 4 0 point for any other option Max Value 1

correctness of 1 response

This item references content from the following areas: CCNA Exploration: Network Fundamentals

10.5.2 Making the Device Management Connection

30

Refer to the exhibit. The router named "myhome" has received a frame from the host 192.168.

The contents of this frame are being sent to host 172.16.14.243. What is the Layer 2 destinatio address of the frame as it leaves the myhome router? 0008.a3b6.ce05 0009.1281.18a8 000a.8a47.e612 172.16.14.129 172.16.14.243 192.168.254.7 Observable 1 Description Max Value 1

correctness 1 point for Option 1 of response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Network Fundamentals

9.7.2 The ARP Process - Destinations outside the Local Network

31

Refer to the exhibit. What two facts can be determined about the network from the exhibited output? (Cho two.) The MontegoBay router does not have any LAN interfaces configured. The Negril router is connected to the S0/1 interface of the MontegoBay router. There are only four devices in this network. Layer 3 is functioning properly on all routers. The MBSwitch is connected to the Negril, Lucia, and MontegoBay routers. Layer 2 is operational on three ports of the MontegoBay router. Observable 1 correctness of response Description 1 point for Option 2, Option 6 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

2.3.3 Cisco Discovery Protocol (CDP)

32 Which set of commands is used to name a router and save the configuration? Router(config)# hostname South South(config)# copy running-config startup-config Router(config)# hostname South South(config)# exit South# copy running-config startup-config Router(config)# ip host South South(config)# copy running-config startup-config Router(config)# ip host South South(config)# exit South# copy running-config startup-config Observable 1 correctness of response Description 1 point for Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2 Applying a Basic Configuration Using Cisco IOS

33 Which command is used to create an encrypted password that restricts access to the privileged EXEC mod Cisco router? RouterA(config)# encrypted password cisco RouterA(config)# password encrypted cisco RouterA(config)# enable password cisco RouterA(config)# enable secret cisco RouterA(config)# service-password encryption cisco Description 1 point for Option 4 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2.2 Limiting Device Access - Configuring Passwords and Using Banners

34

Refer to the exhibit. A network administrator working at HostA has problems accessing the FT server. Layer 3 connectivity testing was successful from HostA to the S0/0/1 interface of Rout Which set of commands will allow the network administrator to telnet to RouterB to check its RouterB(config)# enable secret class RouterB(config)# line vty 0 4 RouterB(config-if)# login RouterB(config)# enable secret class RouterB(config)# line vty 0 RouterB(config-line)# password cisco RouterB(config-line)# login RouterB(config)# enable secret class RouterB(config)# line aux 0 RouterB(config-line)# password cisco RouterB(config-line)# login RouterB(config)# enable secret class RouterB(config)# line aux 0 RouterB(config-vty)# password cisco RouterB(config-vty)# login Observable 1 Description Max Value 1

correctness 1 point for Option 2 of response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2.2 Limiting Device Access - Configuring Passwords and Using Banners

35 What is the purpose of using SSH to connect to a router? It allows a router to be configured using a graphical interface. It allows a secure remote connection to the router command line interface. It allows the router to be monitored through a network management application. It allows secure transfer of the IOS software image from an unsecure workstation or server. Observable 1 correctness of response Description 1 point for Option 2 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

3.3.8 Telnet Services and Protocol

36

Which two statements describe the command ip route 192.168.7.24 255.255.255.248 192.168.7.9? (Choose two.) A packet that is destined for host 192.168.7.30 will be forwarded to address 192.168 The address 192.168.7.9 is the destination network for this route. The address 192.168.7.24 is the next-hop router in this command. This command is issued from the interface configuration mode. This command is used to define a static route. Observable Description 1 point for Option 1, Option 5 0 point for any other option Max Value 1

correctness of 1 response

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

2.4.2 Configuring Static Routes

37 Which protocol is described as an enhanced distance vector routing protocol? RIP v1 RIP v2 EIGRP OSPF Description 1 point for Option 3 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

9.1.1 EIGRP: An Enhanced Distance Vector Routing Protocol

38

Refer to the exhibit. A network administrator can successfully ping, using IP addresses, betw router Jax and router Atlanta. However, when the command telnet Atlanta is entered from t router, the Telnet connection fails. Which two reasons could be the cause of the failure? (Ch two.) The Jax router is not an entry in the host table of the Atlanta router. The Jax router does not have an entry for Atlanta in its host table. The hostname command is not configured correctly on the Atlanta router. The hostname command is not configured correctly on the Jax router. Access to a DNS server is not available. Observable 1 Description Max Value 1

1 point for Option 2, Option correctness of 5 response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.2.2 Basic Router Configuration

39

From what two locations can a router load the Cisco IOS during the boot process? (Choo two.) RAM TFTP server NVRAM setup routine Flash memory terminal Observable Description 1 point for Option 2, Option 5 0 point for any other option Max Value 1

correctness of 1 response

This item references content from the following areas:

CCNA Exploration: Routing Protocols and Concepts

1.1.4 Router Boot-up Process

40

Which two statements describe the functions or characteristics of ROM in a router? (Cho two.) stores routing tables allows software to be updated without replacing pluggable chips on the motherboard maintains instructions for POST diagnostics holds ARP cache stores bootstrap program Observable Description 1 point for Option 3, Option 5 0 point for any other option Max Value 1

correctness of response

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.1.2 Router CPU and Memory

41

Which two statements correctly identify the function of router memory components? (Ch two.) RAM permanently stores the configuration file used during the boot sequence. ROM contains diagnostic self test procedures executed on hardware modules. NVRAM stores a backup copy of the IOS used during the boot sequence. Flash memory does not lose its contents when a router is powered off. ROM contains the most current and most complete version of the IOS. Flash contains boot system commands to identify the location of the IOS. Observable Description 1 point for Option 2, Option 4 0 point for any other option Max Value 1

correctness of response

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.1.2 Router CPU and Memory

42 Which router component holds the routing table, ARP cache, and running configuration file?

RAM Flash NVRAM ROM Observable 1 correctness of response Description 1 point for Option 1 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

1.1.2 Router CPU and Memory

43

Refer to the exhibit. A network administrator can ping the Denver router, but gets a 'Passwor Required but None Set' message when trying to connect remotely via Telnet. Which comman sequence of commands must be applied to the Denver router to allow remote access? Router(config)# line console 0 Router(config-line)# login Router(config-line)# password cisco Router(config)# line vty 0 4 Router(config-line)# login Router(config-line)# password cisco Router(config)# line virtual terminal Router(config-line)# enable login Router(config-line)# password cisco Router(config)# line vty 0 4 Router(config-line)# enable secret Router(config-line)# password cisco Router(config)# enable secret cisco Router(config)# enable cisco Observable Description correctness 1 point for Option 2 1 of response 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: Network Fundamentals

11.2.2 Limiting Device Access - Configuring Passwords and Using Banners

44

Observable 1 correctness of response 2 Obs2 Title 3 Obs3 Title

Description See feedback.

Max Value 1 1 1

This item references content from the following areas:

CCNA Exploration: Routing Protocols and Concepts

7.2.1 Enabling and Verifying RIPv2 Which security method uses the Advanced Encryption Standard (AES)? EAP TKIP WEP WPA2 Observable Description 1 point for Option 4 0 points for any other option Max Value 1

45

correctness of response

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

7.2.2 Wireless Security Protocols

46 What is the purpose of WEP? It encrypts data. It uniquely identifies a wireless network. It coordinates and accepts transmissions from wireless hosts. It provides information about a directly connected Cisco network device. Description 1 point for Option 1 correctness of response 0 point for any other option Observable Max Value 1

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

7.2.2 Wireless Security Protocols

47 A company has an 802.11b wireless access point installed. Which type of wireless NIC is a valid standard based one but will not work in this environment? 802.11a 802.11b 802.11g 802.11n

Observable 1 correctness of response

Description 1 point for Option 1 0 point for any other option

Max Value 1

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

7.1.4 Wireless Operation This is a flash item. Please click below to answer this item.

48

Observabl e 1

Description

Max Value 1

correctness 1 point for correct response of response 0 point for incorrect response

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

7.2.2 Wireless Security Protocols

49 A company has a sales team that travels with laptops. On Fridays, the sales members come into assigned

cubicles and connect their laptop to the wired network. The company is concerned that unauthorized users also connect to the network. What can be done to ensure that unauthorized laptops are not connected to th network? Implement SSH. Install WEP or WPA. Use switch port security. Clearly label the cubicle network port and the switch port. Configure usernames and passwords on the switch ports assigned to each cubicle. Observable 1 correctness of response Description 1 point for Option 3 0 point for any other option Max Value 1

This item references content from the following areas: CCNA Exploration: LAN Switching and Wireless

2.4.6 Configuring Port Security

50

Refer to the exhibit. For security reasons, information about the HQ R1 router model and IP address should not be accessible from the Site 2 R2 router. What security measure should be implemented? Install an IDS between R1 and R2. Install an IPS between R1 and R2. Install a firewall between R1 and R2. Disable CDP on the R1 interface that connects to R2. Disable any routing protocol used between R1 and R2 and install static routes. Observable 1 Description Max Value 1

correctness of 1 point for Option 4 response 0 point for any other option

This item references content from the following areas: CCNA Exploration: Routing Protocols and Concepts

2.3.3 Cisco Discovery Protocol (CDP)

Showing 1 of 1

Prev Page: Next