Enuk8m800 Micro Am2

Download as pdf or txt
Download as pdf or txt
You are on page 1of 43

K8M800 Micro AM2 BIOS Setup

BIOS Setup .........................................................................................................1


1 Main Menu ............................................................................................................................. 3 2 Standard CMOS Features ....................................................................................................... 6 4 Advanced Chipset Features .................................................................................................. 16 5 Integrated Peripherals........................................................................................................... 23 6 Power Management Setup .................................................................................................... 30 7 PnP/PCI Configurations ....................................................................................................... 36 8 PC Health Status................................................................................................................... 39 9 Frequency/ Voltage Control ................................................................................................. 41

K8M800 Micro AM2 BIOS Setup


BIOS Setup
Introduction
This manual discussed Award Setup program built into the ROM BIOS. The Setup program allows users to modify the basic system configuration. This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off. The Award BIOS installed in your computer systems ROM (Read Only Memory) is a custom version of an industry standard BIOS. This means that it supports AMD processor input/output system. The BIOS provides critical low-level support for standard devices such as disk drives and serial and parallel ports. Adding important has customized the Award BIOS, but nonstandard, features such as virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. The rest of this manual is intended to guide you through the process of configuring your system using Setup.

Plug and Play Support


These AWARD BIOS supports the Plug and Play Version 1.0A specification. ESCD (Extended System Configuration Data) write is supported.

EPA Green PC Support


This AWARD BIOS supports Version 1.03 of the EPA Green PC specification.

APM Support
These AWARD BIOS supports Version 1.1&1.2 of the Advanced Power Management (APM) specification. Power management features are implemented via the System Management Interrupt (SMI). Sleep and Suspend power management modes are supported. Power to the hard disk drives and video monitors can be managed by this AWARD BIOS.

ACPI Support
Award ACPI BIOS support Version 1.0 of Advanced Configuration and Power interface specification (ACPI). It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification, developed by Microsoft, Intel and Toshiba.

K8M800 Micro AM2 BIOS Setup


PCI Bus Support
This AWARD BIOS also supports Version 2.1 of the Intel PCI (Peripheral Component Interconnect) local bus specification.

DRAM Support
DDR SDRAM (Double Data Rate Synchronous DRAM) are supported.

Supported CPUs
This AWARD BIOS supports the AMD CPU.

Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to select, use the <PgUp> and <PgDn> keys to change entries, press <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program by using the keyboard.

Keystroke
Up arrow Down arrow Left arrow Right arrow Move Enter PgUp key PgDn key + Key - Key Esc key F1 key F5 key F7 key F10 key

Function
Move to previous item Move to next item Move to the item on the left (menu bar) Move to the item on the right (menu bar) Move to the item you desired Increase the numeric value or make changes Decrease the numeric value or make changes Increase the numeric value or make changes Decrease the numeric value or make changes Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu General help on Setup navigation keys Load previous values from CMOS Load the optimized defaults Save all the CMOS changes and exit

K8M800 Micro AM2 BIOS Setup


1 Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. !! WARNING !! The information about BIOS defaults on manual (Figure 1,2,3,4,5,6,7,8,9) is just for reference, please refer to the BIOS installed on board, for update information.

Figure 1: Main Menu

Standard CMOS Features


This submenu contains industry standard configurable options.

Advanced BIOS Features


This submenu allows you to configure enhanced features of the BIOS.

Advanced Chipset Features


This submenu allows you to configure special chipset features.

K8M800 Micro AM2 BIOS Setup


Integrated Peripherals
This submenu allows you to configure certain IDE hard drive options and Programmed Input/ Output features. Power Management Setup This submenu allows you to configure the power management features.

PnP/PCI Configurations
This submenu allows you to configure certain Plug and Play and PCI options.

PC Health Status
This submenu allows you to monitor the hardware of your system.

Frequency/ Voltage Control


This submenu allows you to change CPU Vcore Voltage and CPU/PCI clock. (However, this function is strongly recommended not to use. Not properly change the voltage and clock may cause the CPU or M/B damage!)

Load Optimized Defaults


This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence. These configurations are factory settings optimized for this system. A confirmation message will be displayed before defaults are set.

Set Supervisor Password


Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility. You will be prompted with to enter a password.

K8M800 Micro AM2 BIOS Setup


Set User Password
If the Supervisor Password is not set, then the User Password will function in the same way as the Supervisor Password. If the Supervisor Password is set and the User Password is set, the User will only be able to view configurations but will not be able to change them.

Save & Exit Setup


Save all configuration changes to CMOS(memory) and exit setup. Confirmation message will be displayed before proceeding.

Exit Without Saving


Abandon all changes made during the current session and exit setup. message will be displayed before proceeding. Confirmation

Upgrade BIOS
This submenu allows you to upgrade bios.

K8M800 Micro AM2 BIOS Setup


2 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into 10 categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the<PgUp> or <PgDn> keys to select the value you want in each item.

Figure 2: Standard CMOS Setup

K8M800 Micro AM2 BIOS Setup


Main Menu Selections
This table shows the selections that you can make on the Main Menu.

Item
Date

Options
mm : dd : yy

Description
Set the system date. Note that the Day automatically changes when you set the date. Set the clock. system internal

Time IDE Primary Master

hh : mm : ss Options are in its sub menu. Options are in its sub menu.

Press <Enter> to enter the sub menu of detailed options Press <Enter> to enter the sub menu of detailed options. Press <Enter> to enter the sub menu of detailed options. Press <Enter> to enter the sub menu of detailed options. Select the type of floppy disk drive installed in your system.

IDE Primary Slave

IDE Secondary Master Options are in its sub menu. IDE Secondary Slave Options are in its sub menu. 360K, 5.25 in 1.2M, 5.25 in 720K, 3.5 in 1.44M, 3.5 in 2.88M, 3.5 in None Video EGA/VGA CGA 40 CGA 80 MONO

Drive A Drive B

Select the default video device.

K8M800 Micro AM2 BIOS Setup


Item
Halt On

Options
All Errors No Errors All, but Keyboard All, but Diskette All, but Disk/ Key

Description
Select the situation in which you want the BIOS to stop the POST process and notify you. Displays the amount of conventional memory detected during boot up.

Base Memory

N/A

Extended Memory

N/A

Displays the amount of extended memory detected during boot up.

Total Memory

N/A

Displays the total memory available in the system.

K8M800 Micro AM2 BIOS Setup


3 Advanced BIOS Features
Figure 3: Advanced BIOS Setup

K8M800 Micro AM2 BIOS Setup


Boot Seq & Floppy Setup
This item allows you to setup boot seq & Floppy.

Figure 3.1:

Boot Seq & Floppy Setup

Hard Disk Boot Priority These BIOS attempt to arrange the Hard Disk boot sequence automatically. This will depend on which Hard Disk is installed.

Figure 3.1.1: Hard Disk Boot Priority

The Choices: Pri. Master, Pri. Slave, Sec. Master, Sec, Slave, USB HDD0, USB HDD1, USB HDD2, and Bootable Add-in Cards.

10

K8M800 Micro AM2 BIOS Setup


First/ Second/ Third/ Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items. The Choices: Floppy (default), LS120, Hard Disk, SCSI, CDROM, ZIP100, LAN, Disabled. Swap Floppy Drive For systems with two floppy drives, this option allows you to swap logical drive assignments. The Choices: Disabled (default), Enabled. Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks. Disabling this option reduces the time it takes to boot-up. The Choices: Enabled (default), Disabled

Shadow Setup
This item allows you to setup cache & shadow setup.

Figure 3.2: Shadow Setup

Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution. Enabled (default) Optional ROM is enabled. Disabled Optional ROM is disabled.

11

K8M800 Micro AM2 BIOS Setup


Cache Setup Figure 3.3: Cache Setup

CPU Internal Cache Depending on the CPU/chipset in use, you may be able to increase memory access time with this option. Enabled (default) Enable cache. Disabled Disable cache. External Cache This option enables or disables Level 2 secondary cache on the CPU, which may improve performance. Enabled (default) Enable cache. Disabled Disable cache. CPU L2 Cache ECC Checking This item allows you to enable/disable CPU L2 Cache ECC Checking. The Choices: Enabled (default), Disabled.

12

K8M800 Micro AM2 BIOS Setup


CPU Feature Figure 3.4: CPU Feature

NPT Fid control This function allows you to adjust the frequency ratio of CPU. The Choices: Auto (default), x4: 800Mhz ~ x25: 5000Mhz (differs from CPU) NPT Vid control This function allows you to adjust the CPU voltage. The Choices: Auto (default), 0.375V ~ 1.550V (differs from CPU)

13

K8M800 Micro AM2 BIOS Setup


Virus Warning
This option allows you to choose the VIRUS Warning feature that is used to protect the IDE Hard Disk boot sector. If this function is enabled and an attempt is made to write to the boot sector, BIOS will display a warning message on the screen and sound an alarm beep. Disabled (default) Virus protection is disabled. Enabled Virus protection is activated.

Quick Power On Self Test


Enabling this option will cause an abridged version of the Power On Self-Test (POST) execute after you power up the computer. Disabled Normal POST. Enabled (default) Enable quick POST. to

Boot Up NumLock Status


Selects the NumLock. State after power on. The Choices: On (default) Numpad is number keys. Off Numpad is arrow keys.

Typematic Rate Setting


When a key is held down, the keystroke will repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be configured. The Choices: Disabled (default), Enabled.

Typematic Rate (Chars/Sec)


Sets the rate at which a keystroke is repeated when you hold the key down. The Choices: 6 (default), 8, 10, 12, 15, 20, 24, 30.

Typematic Delay (Msec)


Sets the delay time after the key is held down before it begins to repeat the keystroke. The Choices: 250 (default), 500, 750, 1000.

Security Option
This option will enable only individuals with passwords to bring the system online and/or to use the CMOS Setup Utility. System A password is required for the system to boot and is also required to access the Setup Utility. Setup (default) A password is required to access the Setup Utility only. This will only apply if passwords are set from the Setup main menu.

14

K8M800 Micro AM2 BIOS Setup


APIC Mode
Selecting Enabled enables APIC mode reporting from the BIOS to the operating system. The Choices: Enabled (default), Disabled

MPS Version Control For OS


The BIOS supports version 1.1 and 1.4 of the Intel multiprocessor specification. Select version supported by the operation system running on this computer. The Choices: 1.4 (default), 1.1.

OS Select For DRAM > 64MB


A choice other than Non-OS2 is only used for OS2 systems with memory exceeding 64MB. The Choices: Non-OS2 (default), OS2.

Delay for HDD (Secs)


This item allows you to select the timing of Delay for HDD The Choices: 0 (default). Min= 0 Max= 15 Key in a DEC number.

Small LOGO (EPA) Show


This item allows you to select whether the Small Logo shows. Enabled (default) Small Logo shows when system boots up. Disabled No Small Logo shows when system boots

Summary Screen Show


This item allows you to enable/disable the summary screen. Summary screen means system configuration and PCI device listing. The Choices: Disabled (default), Enabled.

15

K8M800 Micro AM2 BIOS Setup


4 Advanced Chipset Features
This submenu allows you to configure the specific features of the chipset installed on your system. This chipset manage bus speeds and access to system memory resources, such as DRAM. It also coordinates communications with the PCI bus. The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly.

Figure 4: Advanced Chipset Setup

16

K8M800 Micro AM2 BIOS Setup


AGP & P2P Bridge Control
If you highlight the literal Press Enter next to the AGP & P2P Bridge Control label and then press the enter key, it will take you a submenu with the following options:

Figure 4.1: AGP & P2P Bridge Control

AGP Aperture Size


Select the size of the Accelerated Graphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation. The Choices: 1G,512M,256M, 128M (default), 64M ,32M. AGP 2.0 Mode This item allows you to select the AGP Mode. The Choices: 4X (default), 2X, 1X. AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card. By choosing Manual, it allows user to set AGP output Buffer Drive strength P Ctrl by manual. The Choices: Auto (default), Manual.

17

K8M800 Micro AM2 BIOS Setup


AGP Driving Value While AGP driving control item set to Manual, it allows user to set AGP driving. The Choices: DA (default). AGP Fast Write This item allows you to disabled or enabled AGP Fast Write. The Choices: Disabled (default), Enabled. AGP Master 1 WS Write When Enabled, writes to the AGP (Accelerated Graphics Port) are executed with one-wait states. The Choices: Disabled (default), Enabled. AGP Master 1 WS Read When Enabled, read to the AGP (Accelerated Graphics Port) are executed with one wait states. The Choices: Disabled (default), Enabled. AGP 3.0 Calibration cycle This item allows you to disabled or enabled AGP 3.0 Calibration Cycle. The Choices: Disabled (default), Enabled. DBI Output for AGP Trans The Choices: Disabled (default), Auto. VGA Share Memory Size This item allows you to select the VGA share memory size. The Choices: 64M (default), 32M, 16M Disabled.

18

K8M800 Micro AM2 BIOS Setup


DRAM Configuration Figure 4.2: DRAM Configuration

Timing Mode
This item allows you to choose to manually or automatically regulate the DDR Timing. The Choices: Auto (default), Manual.

DQS Training Control


The Choices: Skip DQS (default), Perform DQS.

CKE base power down mode


The Choices: Enabled (default), Disabled

CKE based power down


The Choices: Per Channel (default), Per CS.

Memory tri-stating
The Choices: Disabled (default), Enabled.

Memory Hole Remapping


The Choices: Disabled (default), Enabled.

Bottom of UMA DRAM [31:24]


The Choices: FC (default), 00~FF.

19

K8M800 Micro AM2 BIOS Setup


DDRII Timing Item
The Choices: Disabled (default), Enabled.

TwTr Command Delay


The Choices: 3 bus clocks (default).

TrTfc0 for DIMM0


The Choices: 75ns (default).

TrTfc1 for DIMM1


The Choices: 75ns (default)

<Twr> Write Recovery Time


The Choices: 6 bus clocks (default).

<Trtp> Precharge Time


The Choices: 3 clocks (default).

<Trc> Row Cycle Time


The Choices: 26 bus clocks (default).

<Trcd> RAS to CAS R/W Delay


The Choices: 6 clocks (default).

<Trrd> RAS to RAS Delay


The Choices: 5 clocks (default).

<Trp> Row Precharge Time


The Choices: 6 clocks (default).

<Tras> Minimum RAS Active T


The Choices: 18 bus clocks (default).

20

K8M800 Micro AM2 BIOS Setup


LDT & PCI Bus Control
If you highlight the literal Press Enter next to the LDT & PCI Bus Control label and then press the enter key, it will take you a submenu with the following options

: Figure 4.3: LDT & PCI Bus Control

Upstream LDT Bus Width The Choices: 8 bit, 16 bit (default). Downstream LDT Bus Width
The Choices: 8 bit, 16 bit (default).

LDT Bus Frequency


The Choices: 800MHz (default)., Auto, 600MHz, 400MHz, 200MHz.

PCI1 Master 0 WS Write


When enabled, writes to the PCI bus are executed with zero-wait states. The Choices: Enabled (default), Disabled.

PCI2 Master 0 WS Write


When enabled, writes to the PCI bus are executed with zero-wait states. The Choices: Enabled (default), Disabled.

21

K8M800 Micro AM2 BIOS Setup


PCI1 Post Write
When enabled, writes to the PCI bus are executed with zero-wait states. The Choices: Enabled (default), Disabled.

PCI2 Post Write


When enabled, writes to the PCI bus are executed with zero-wait states. The Choices: Enabled (default), Disabled.

PCI Delay Transaction


The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification. The Choices: Enabled (default), Disabled.

Memory Hole
You can reserve this area of system memory for ISA adapter ROM. When this area is reserved it cannot be cached. The user information of peripherals that need to use this area of system memory usually discussed their memory requirements. The Choices: Disabled (default), 15M 16M.

Vlink Date Rate


The Choices: 8X (default), 4X

Init Display First


With systems that have multiple video cards, this option determines whether the primary display uses a PCI Slot or an AGP Slot. The Choices: PCI Slot (default), AGP.

System BIOS Cacheable


Selecting the Enabled option allows caching of the system BIOS ROM at F0000h-FFFFFh which can improve system performance. However, any programs writing to this area of memory will cause conflicts and result in system errors. The Choices: Enabled, Disabled (default).

22

K8M800 Micro AM2 BIOS Setup


5 Integrated Peripherals
Figure 5. Integrated Peripheral

23

K8M800 Micro AM2 BIOS Setup


VIA OnChip IDE Device
If you highlight the literal Press Enter next to the VIA OnChip IDE Device label and then press the enter key, it will take you a submenu with the following options:

Figure 5.1: VIA OnChip IDE Device

OnChip SATA This option allows you to enable the onchip Serial ATA. The Choices: Enabled (default), Disabled. SATA Mode This option allows you to select SATA Mode. The Choices: IDE, RAID (default). IDE DMA Transfer Access This option allows you to select IDE DMA Transfer Access. The Choices: Enabled (default), Disabled. OnChip IDE Channel 0/1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the first and/or second IDE interface. Select Disabled to deactivate an interface if you are going to install a primary and/or secondary add-in IDE interface. The Choices: Enabled (default), Disabled.

24

K8M800 Micro AM2 BIOS Setup


IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access. If the interface does not support prefetching. If you install a primary and/or secondary add-in IDE interface, set this option to Disabled. The Choices: Enabled (default), Disabled. Primary / Secondary /Master / Slave PIO The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. Modes 0 to 4 will increase performance progressively. In Auto mode, the system automatically determines the best mode for each device. The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4. Primary / Secondary /Master / Slave UDMA Ultra DMA/100 functionality can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 OSR2 or a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/100, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read / write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read / write per sector where the drive can support. The Choices: Enabled (default), Disabled.

25

K8M800 Micro AM2 BIOS Setup


VIA OnChip PCI Device
If you highlight the literal Press Enter next to the VIA OnChip PCI Device label and then press the enter key, it will take you a submenu with the following options:

Figure 5.2: VIA OnChip PCI Device

VIA-3058 AC97 Audio This option allows you to control the onboard AC97 audio. The Choices: Auto (default), Disabled. VIA-3068 MC97 Modem This option allows you to control the onboard MC97 Modem The Choices: Auto (default), Disabled. VIA-3043 MC97 Onchip LAN This option allows you to control the onboard LAN The Choices: Enabled (default), Disabled. Onboard Lan Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip. The Choices: Enabled, Disabled (default).

26

K8M800 Micro AM2 BIOS Setup


OnChip USB Controller This option should be enabled if your system has a USB installed on the system board. You will need to disable this feature if you add a higher performance controller. The Choices: All Enabled (default), All Disabled, 1&2 USB Port, 2&3 USB Port, 1&3 USB Port, 1 USB Port, 2 USB Port, 3 USB Port. Onchip EHCI Controller This item allows you to enable or disable the onchip EHCI controller. The Choices: Enabled (default), Disabled. USB Emulation Support This item allows you to enable or disable the USB Keyboard/ Mouse Legacy Support. The Choices: On (default), off, KB/ MS. USB Keyboard Support Enables support for USB attached mouse/keyboard. The Choices: Auto (default), Enabled. USB Mouse Support Enables support for USB attached mouse/keyboard. The Choices: Disabled (default), Enabled.

27

K8M800 Micro AM2 BIOS Setup


Super IO Device
Press Enter to configure the Super I/O Device.

Figure 5.3: Super IO Device

Onboard FDC Controller


Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. The Choices: 3F8/IRQ4 (default), Disabled, Auto, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O Address. The Choices: 378/IRQ7 (default), 278/IRQ5, 3BC/IRQ7, Disabled.

28

K8M800 Micro AM2 BIOS Setup


Parallel Port Mode The default value is SPP. The Choices: SPP (default) Using Parallel Port as Standard Printer Port. EPP Using Parallel Port as Enhanced Parallel Port. ECP Using Parallel Port as Extended Capabilities Port. ECP+EPP Using Parallel Port as ECP & EPP mode. ECP Mode Use DMA This item allows you to determine ECP Mode Use DMA. The Choices: 3 (default), 1.

29

K8M800 Micro AM2 BIOS Setup


6 Power Management Setup
The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features.

Figure 6: Power Management Setup

ACPI function
This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled.

ACPI Suspend Type


The item allows you to select the suspend type under the ACPI operating system. The Choices: S1 (POS) (default) Power on Suspend S3 (STR) Suspend to RAM S1+S3 POS+STR

30

K8M800 Micro AM2 BIOS Setup


Power Management Option
This category allows you to select the type (or degree) of power saving and is directly related to the following modes: 1.HDD Power Down. 2.Suspend Mode. There are four options of Power Management, three of which have fixed mode settings

Min. Power Saving


Minimum power management. Suspend Mode = 1 hr. HDD Power Down = 15 min

Max. Power Saving


Maximum power management only available for sl CPUs. Suspend Mode = 1 min. HDD Power Down = 1 min.

User Define (default)


Allows you to set each mode individually. When not disabled, each of the ranges is from 1 min. to 1 hr. except for HDD Power Down which ranges from 1 min. to 15 min. and disable.

HDD Power Down


When enabled, the hard disk drive will power down and after a set time of system inactivity. All other devices remain active. The Choices: Disabled (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min, 9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min.

Suspend Mode
The item allows you to select the suspend type under ACPI operating system. The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 1 Hour

Video Off Option


This option determines the manner in which the monitor is goes blank. The Choices: SuspendOff (default).

31

K8M800 Micro AM2 BIOS Setup


Video Off Method
This option determines the manner in which the monitor is goes blank. V/H SYNC+Blank (default) This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer.

Blank Screen
This option only writes blanks to the video buffer. DPMS Initial display power management signaling.

MODEM Use IRQ


This determines the IRQ, which can be applied in MODEM use. The Choices: 3 (default)/ 4 / 5 / 7 / 9 / 10 / 11 / NA

Soft-Off by PWR-BTN
Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has hung. The Choices: Delay 4 Sec, Instant-Off (default).

Run VGABIOS if S3 Resume


Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state. The system time is shortened if you disable the function, but system will need AGP driver to initialize the card. So, if the AGP driver of the VGA card does not support the initialization feature, the display may work abnormally or not function after S3. The Choices: Auto (default), Yes, No.

Ac Loss Auto Restart


This field determines the action the system will automatically take when power is restored to a system that had lost power previously without any subsequent manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard battery (3V). If AC power is supplied and the Power Supply is not turned on, 5VSB from the Power Supply is used. When the Power Supply is eventually turned on 3.3V from the Power Supply will be used. There are 3 options: Former-Sts, On, Off. Off (default) Means always set CMOS to the Off status when AC power is lost. On Means always set CMOS to the On status when AC power is lost Former-Sts Means to maintain the last status of the CMOS when AC power is lost.

32

K8M800 Micro AM2 BIOS Setup


For example: If set to Former-Sts and AC power is lost when system is live, then after AC power is restored, the system will automatically power on. If AC power is lost when system is not live, system will remain powered off.

IRQ/Event Activity Detect


If you highlight the literal Press Enter next to the IRQ/Event Activity Detect label and then press the enter key, it will take you a submenu with the following options:

DPMS
Initial display power management signaling. The Choices: Stop Grant, PwrOn Suspend.

Figure 6.1:IRQ/Event Activity Detect

PS2KB Wakeup Select When select Password, please press Enter key to change password with a maximum of 8 characters. The Choices: Hot Key (default). PS2KB Wakeup from S3/ S4/ S5 This item allows you to wake up from S3/ S4/ S5 with PS2 keyboard. The Choices: Disabled (default), Ctrl+F1, Ctrl+F2. Ctrl+F3, Ctrl+F4, Ctrl+F5, Ctrl+F6, Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11, Ctrl+F12, Power, Wake, Any Key.

33

K8M800 Micro AM2 BIOS Setup


USB Resume from S3 This item allows you to enable or disabled USB resume from S3. The Choices: Disabled (default), Enabled. VGA When set to On, any event occurring at a VGA Port will awaken a system which has been powered down. The Choices: Off (default), On. LPT & COM When this option is set to On, any event occurring at a COM(serial)/LPT (printer) port will awaken a system which has been powered down. The Choices: LPT/COM (default), COM, LPT, NONE. HDD & FDD When this option is set to On, any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down. The Choices: On (default), Off. PCI Master When set to On, you need a LAN add-on card which supports the power function. It should also support the wake-up on LAN jump. The Choices: Off (default), On. PowerOn by PCI Card When you select Enabled, a PME signal from PCI card returns the system to Full ON state. The Choices: Disabled (default), Enabled. Modem Ring Resume The Choices: Disabled (default), Enabled. RTC Alarm Resume When Enabled, you can set the date and time at which the RTC (real-time clock) alarm awakens the system from Suspend mode. The Choices: Enabled, Disabled (default). Date (of Month) You can choose which month the system will boot up. This field is only configurable when RTC Resume is set to Enabled. Resume Time (hh:mm:ss) You can choose the hour, minute and second the system will boot up. This field is only configurable when RTC Resume is set to Enabled.

34

K8M800 Micro AM2 BIOS Setup


IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events (i.e. wake on LPT & COMM activity). Figure 6.1.1: IRQs Activity Monitoring

Primary INTR IRQ3 (COM2) IRQ4 (COM1) IRQ5 (LPT2) IRQ6 (Floppy Disk) IRQ7 (LPT1) IRQ8 (RTC Alarm) IRQ9 (IRQ2 Redir) IRQ10 (Reserved) IRQ11 (Reserved) IRQ12 (PS/2 Mouse) IRQ13 (Coprocessor) IRQ14 (Hard Disk) IRQ15 (Reserved)

On Enabled Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Disabled

35

K8M800 Micro AM2 BIOS Setup


7 PnP/PCI Configurations
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

Figure 7: PnP/PCI Configurations

PNP OS Installed
When set to YES, BIOS will only initialize the PnP cards used for the boot sequence (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like Window 95. When set to NO, BIOS will initialize all the PnP cards. For non-PnP operating systems (DOS, Netware), this option must set to NO. The Choices: No (default), Yes.

36

K8M800 Micro AM2 BIOS Setup


Reset Configuration Data
The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict. Every peripheral device has a node, which is called ESCD. This node records which resources are assigned to it. The system needs to record and update ESCD to the memory locations. These locations (4K) are reserved in the system BIOS. If the Disabled (default) option is chosen, the systems ESCD will update only when the new configuration varies from the last one. If the Enabled option is chosen, the system is forced to update ESCDs and then is automatically set to the Disabled mode. The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function. Legacy is the term, which signifies that a resource is assigned to the ISA Bus and provides non-PnP ISA add-on cards. PCI / ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add-on cards and peripherals. The Choices: Disabled (default), Enabled.

Resources Controlled By
By Choosing Auto(ESCD) (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral. By Choosing Manual, the user will need to assign IRQ & DMA for add-on cards. Be sure that there are no IRQ/DMA and I/O port conflicts.

IRQ Resources
This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the Press Enter tag, you will be directed to a submenu that will allow you to configure the system interrupts. This is only configurable when Resources Controlled By is set to Manual. IRQ-3 IRQ-4 IRQ-5 IRQ-7 IRQ-9 IRQ-10 IRQ-11 IRQ-12 IRQ-14 IRQ-15 assigned to assigned to assigned to assigned to assigned to assigned to assigned to assigned to assigned to assigned to PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device PCI Device

37

K8M800 Micro AM2 BIOS Setup


PCI / VGA Palette Snoop
Choose Disabled or Enabled. Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility. However, the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors, and the graphic controller needs to know what is in the palette of the VGA controller. To do this, the non-VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data. In PCI based systems, where the VGA controller is on the PCI bus and a non-VGA graphic controller is on an ISA bus, the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write. In this case, the PCI VGA controller should not respond to the Write, it should only snoop the data and permit the access to be forwarded to the ISA bus. The non-VGA ISA graphic controller can then snoop the data on the ISA bus. Unless you have the above situation, you should disable this option. Disabled (default) Disables the function. Enabled Enables the function.

Assign IRQ For VGA


This item allows the users to choose which IRQ to assign for the VGA. The Choices: Enabled (default), Disabled.

Assign IRQ For USB


This item allows the users to choose which IRQ to assign for the USB. The Choices: Enabled (default), Disabled.

38

K8M800 Micro AM2 BIOS Setup


8 PC Health Status
Figure 8: PC Health Status

Shutdown Temperature
This item allows you to set up the CPU shutdown Temperature. The Choices: 70/ 158, 75/ 167, 80/ 176, 85/ 185(default)

CPU Vcore/ 3.3V/ +5.0V/ +12V/DDR Voltage/ LDT Voltage/Voltage Battery


Detect the systems voltage and battery status automatically.

CPU Temperature
Show you the CPU temperature.

CPU FAN Speed


This field displays the CPU FAN speed.

39

K8M800 Micro AM2 BIOS Setup


SYS FAN Speed
This field displays the speed of the SYSTEM fan.

Show H/W Monitor in POST


If you computer contain a monitoring system, it will show PC health status during POST stage. The item offers several delay time to select you want The Choices: Enabled (default), Disabled.

Chassis Open Warning


This item allows you to enable or disable Chassis Open Warning beep. The Choices: 60OC/140OF, 65OC/149OF, 70OC/158OF, Disabled (default).

40

K8M800 Micro AM2 BIOS Setup


9 Frequency/ Voltage Control
Figure 9: Frequency/ Voltage Control

CPU Vcore
The Choices: Default (default), +0.15V, +0.10V, +0.05V.

DDR Voltage
This item allows you to select DDR Voltage. The Choices: 1.95V (default), 2.05V, 2.15V, 2.25V.

AutoDetect PCI Clk


This item allows you to enable / disable auto Detect PCI Clock. The Choices: Enabled (default), Disabled.

Spread Spectrum
This item allows you to enable/disable the Spread Spectrum function. The Choices: Enabled (default), Disabled

41

K8M800 Micro AM2 BIOS Setup


CPU CLOCK
This item allows you to select CPU Clock, and CPU over clocking The Choices: 200Mhz (default), Disabled. Min= Max= 200 232

Key in a DEC number. Special Notice: If unfortunately, the systems frequency that you are selected is not functioning, there are two methods of booting-up the system. Method 1: Clear the COMS data by setting the JCOMS1 ((2-3) closed)) as ON status. All the CMOS data will be loaded as defaults setting. Method 2: Press the <Insert> key and Power button simultaneously, after that keep-on pressing the <Insert> key until the power-on screen showed. This action will boot-up the system according to FSB of the processor. Its strongly recommended to set CPU Vcore and clock in default setting. If the CPU Vcore and clock are not in default setting, it may cause CPU or M/B damage.

42

You might also like