Service Bulletin

Applies To:

98-011
February 20, 2004

ALL See index below

Keyless Remote Transmitter Information

(Supersedes 98-011, dated February 6, 2003) This service bulletin gives you information about keyless remote transmitters for most Honda vehicles. Each procedure describes transmitter programming (if applicable), transmitter ordering, and transmitter batteries. A remote transmitter quick reference guide starts on page 16. Use this index to find the information for the vehicle you are working on.
Model Accord Year(s) 199093 199193 199193 199495 199495 199697 199697 1997 199802 199802 2000 2002 200304 200304 Civic 199293 199495 199698 199698 199900 199903 199904 2004 2004 200204 200304 del Sol 1993 199495 199697 Insight 200004 Trim Level Except 5-door 5-door EX 5-door LX Except 5-door EX 5-door EX 5-door EX Except SE & 5-door EX SE DX & LX EX SE SE DX LX & EX ALL ALL Except EX EX Value Package Except EX EX Except LX & EX LX Si Hybrid ALL ALL ALL ALL With Factory- Installed Keyless Entry or Security System N/A Page 6 N/A N/A Page 6 Page 6 N/A Page 8 N/A Page 8 Page 8 Page 8 N/A Page 9 N/A N/A N/A Page 4 Page 5 N/A Page 5 N/A Page 5 Page 5 Page 5 N/A N/A N/A Page 12 With Dealer- Installed Keyless Entry System N/A N/A N/A N/A N/A N/A N/A N/A Page 7 N/A N/A N/A N/A N/A N/A N/A Page 4 N/A N/A Page 5 N/A Page 5 N/A N/A N/A N/A N/A N/A N/A With DealerInstalled Security System Page 3 Page 6 Page 6 Page 4 Page 4 Page 7 Page 7 N/A Page 7 N/A N/A N/A Page 5 N/A Page 3 Page 4 Page 4 Page 4 Page 5 Page 5 Page 5 Page 5 Page 5 Page 5 Page 5 Page 3 Page 4 Page 7 Page 7

2004 American Honda Motor Co., Inc. All Rights Reserved

ATB 18248-26885 (0402)

1 of 21

CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,

and training to correctly and safely maintain your vehicle. These procedures should not be attempted by do-it-yourselfers, and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer.

Model Prelude

Year(s) 198891 199293 199495 199698 199901 ALL ALL ALL ALL ALL ALL LX EX SE EX LX ALL

Trim Level

With Factory- Installed Keyless Entry or Security System N/A N/A N/A N/A Page 11 Page 10 N/A Page 10 Page 10 Page 10 N/A N/A N/A Page 5 N/A Page 6 N/A Page 6 N/A Page 10 Page 10 N/A N/A Page 15 N/A Page 5 Page 12

With Dealer- Installed Keyless Entry System N/A N/A N/A N/A N/A N/A Page 10 N/A N/A N/A Page 10 Page 5 Page 5 N/A N/A N/A N/A N/A Page 7 N/A N/A N/A N/A N/A Page 7 N/A N/A

With DealerInstalled Security System Page 12 Page 3 Page 4 Page 7 Page 7 Page 7 Page 7 Page 7 Page 7 Page 10 Page 10 Page 5 Page 5 Page 5 Page 4 Page 4 Page 7 Page 7 Page 7 Page 10 N/A Page 13 Page 14 N/A Page 7 N/A N/A

S2000 CR-V

200004 199701 199801 200001 200204 200204

Element

2003 2004 2004

DX & LX EX LX EX LX EX LX EX EX models Except 1995* ALL ALL LX EX models ALL

Odyssey

1995 1995 199698 199698 199904 199900 200104

Passport

199495 199697 199802

Pilot EV Plus

200304 200304 199799

* 1995 Passport did not offer Keyless Entry or Security.

2 of 21

98-011

199093 Accord (2-door and 4-door) with dealer-installed security system 199293 Civic with dealer-installed security system 1993 del Sol with dealer-installed security system 199293 Prelude with dealer-installed security system

5. Reinstall the rear covers on the transmitters. 6. Remove the security system control unit from under the drivers seat. 7. Open the access cover on the control unit, and replace the ROM chip. (Use the same procedure as in steps 2 and 3.)

CONTROL UNIT ACCESS COVER

ROM CHIP
P/N 08E50-SM4-110, H/C 3524733
Programming the Transmitter NOTE: This system uses ROM chips that match the transmitter to the security system control unit. When replacing a lost or stolen transmitter, you need to use the three ROM chips (provided with the new transmitter) to match the old transmitter with the new transmitter and the control unit. 1. Remove the rear cover from the old transmitter and the new one. 2. Remove the ROM chip from the old transmitter by sliding its socket holder toward the ROM chip. 8. Press the reset button next to the ROM chip. 9. Close the access cover, and reinstall the control unit. If you are replacing a damaged transmitter, dont replace the ROM chips in the transmitters and the control unit; just remove the chip from the old transmitter and install it in the new one. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. If your customer wants to add a third transmitter to the system, you need to order a four ROM chip set directly from Alpine Electronics of America. The Alpine part number for the four ROM chip set is 8319. This ROM chip set does not come with a transmitter. Order the additional transmitter from American Honda. If you have questions about how to order a four ROM chip set, call Alpines parts department at (800) 421-2284, extension 8885. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

TRANSMITTER REAR COVER

Slide socket holder toward chip.

ROM CHIP

Pull out ROM chip.

3. Insert a new ROM chip into the socket holder, then slide the socket holder toward the socket to lock the chip in place. 4. Repeat step 3 to install a ROM chip into the new transmitter.

98-011

3 of 21

199495 Accord with dealer-installed security system 199495 Civic with dealer-installed security system 199495 del Sol with dealer-installed security system 199495 Prelude with dealer-installed security system 1995 Odyssey with dealer-installed security system

Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

199698 Civic EX with factory-installed keyless entry system 199698 Civic (except EX) with dealer-installed keyless entry system 199698 Civic with dealer-installed security system

P/N 08E51-SV4-1M001, H/C 4285565

Programming the Transmitter NOTES: The system uses a stacking-type memory that accepts up to four transmitters. If you program a fifth transmitter, the systems memory for the first transmitter is pushed out, and it will no longer work. To clear a lost or stolen transmitter from the systems memory, program a transmitter four times. This will remove the missing transmitter from memory, since only four transmitter codes can be accepted. Another way to clear a lost or stolen transmitter is to erase all transmitter codes, and then reprogram them. To do this, refer to the security system owners manual. 1. Turn the ignition switch to ON (II). 2. Press and hold the Valet-Disarm button on the dashboard lower cover. (Continue to hold the button during this procedure, or programming will be cancelled.) The LED on the upper steering column cover flashes when the system is in programming mode. 3. Press the top button on the transmitter. Check that the parking lights flash to confirm that the transmitters code was accepted. 4. Press the top button on each of the remaining transmitters. Check that the parking lights flash after each transmitter code is accepted. 5. Release the Valet-Disarm button to exit the programming mode.

P/N 39950-S01-A01 H/C 4811352

Programming the Transmitter NOTES: The system accepts up to four transmitters. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all the transmitters once youre in the programming mode. 1. Turn the ignition switch to ON (II). 2. Press and hold the Valet-Disarm button on the radio (between the VALETDISARM AM/FM and CD/TAPE buttons) to BUTTON enter the programming mode. (Continue to hold the button during this procedure, or programming will be cancelled.) Check that the power door locks cycle to confirm that youre in the programming mode. 3. Within 5 seconds, press the Lock or Unlock button on the transmitter. Check that the power door locks cycle to confirm that the code was accepted. 4. Within 10 seconds, press the Lock or Unlock button on each of the remaining transmitters. 5. After all the transmitters have been programmed, release the Valet-Disarm button to exit programming mode.

4 of 21

98-011

Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

199900 Civic Value Package with factoryinstalled keyless entry system 199904 Civic EX with factory-installed keyless entry system or dealer-installed security system 199903 Civic (except EX) with dealer-installed keyless entry system or security system 200204 Civic Si with factory-installed keyless entry system or dealer-installed security system 200304 Civic Hybrid with factory-installed keyless entry system or dealer-installed security system 2004 Civic (except LX & EX) with dealerinstalled keyless entry system or security system 2004 Civic LX with factory-installed keyless entry system or dealer-installed security system 200304 Accord DX with dealer-installed security system 200304 Element with dealer-installed keyless entry system or security system 2004 Element EX with factory-installed keyless entry system or dealer-installed security system 200304 Pilot EX models with factory-installed security system

98-011

5 of 21

199193 Accord 5-door EX with factoryinstalled keyless entry or dealer-installed security system

Programming the Transmitter This transmitter is not programmable. Ordering a Transmitter Transmitters can be ordered directly from Kenwood USA only by authorized Honda dealers. Send a completed order form (copy it from the Accessory Replacement Parts section of the Dealer Parts Price List) along with a dealer check for $30.00 (payable to Kenwood U.S.A. Corp.) to this address: Kenwood Service Corp. P.O. Box 22745 Long Beach, CA 90801-5745 On the order form, you must include the serial number of the keyless control unit or the number from one of the original transmitters. If you need a transmitter shipped overnight, fill out the order form, then call Kenwood at (800) 852-4690, or fax them at (310) 898-1029 (weekdays from 8:30 A.M. thru 4:00 P.M. Pacific time). You will need to give the information on the order form to the Kenwood representative. The transmitter will be sent to your dealership COD. Additional shipping and handling charges will be applied to the order. Batteries for the Transmitter The battery number is CR1220. Each transmitter uses two batteries.

P/N 04808-SM5-A01, H/C 3721735

Programming the Transmitter The transmitter is not programmable. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. To order a transmitter, you need the vehicles VIN, the code number from the power door lock control unit, and the ignition key code number. The power door lock code number is a five-digit number etched into the plastic case of the control unit (mounted under the drivers seat). The ignition key code number is a four-digit number stamped on the metal shank of all five original keys delivered with the car. Replacement transmitters are manufactured to match the code of the keyless entry system. The new ignition key is cut to match the vehicles ignition switch, front door locks, tailgate lock, and glove compartment lock. To order this transmitter, use the controlled parts ordering screen on the iN system. The transmitters are manufactured in Japan; delivery takes 4 to 6 weeks. Batteries for the Transmitter The battery is not replaceable.

199497 Accord 5-door EX with factoryinstalled keyless entry system 199598 Odyssey EX with factory-installed keyless entry system

199193 Accord 5-door LX with dealerinstalled security system

Programming the Transmitter NOTE: The system accepts up to two transmitters. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode.

No P/N

6 of 21

98-011

1. Open the drivers door. 2. Push the drivers power door lock switch to the unlock position and hold it. (Continue to hold the switch during this procedure.) 3. Insert the key into the ignition switch, then remove it. Repeat this four more times (five times total) within 10 seconds. (You must complete steps 3 and 4 within 10 seconds or the system will exit the programming mode.) 4. Insert the key into the ignition switch. After you insert the key, make sure the power door locks cycle to confirm that the system is in the programming mode. 5. Press the LOCK or UNLOCK button on the transmitter. All the power door locks (except the drivers door) should cycle to confirm that the system accepted the transmitters code. 6. To program a second transmitter, press its LOCK or UNLOCK button within 10 seconds of programming the first transmitter. 7. Release the master power door lock switch to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2016. Each transmitter uses two batteries.

199602 Accord with dealer-installed security system 199802 Accord DX & LX with dealer-installed keyless entry system 199701 CR-V with dealer-installed security system 199697 del Sol with dealer-installed security system 199698 Odyssey with dealer-installed security system 199904 Odyssey LX with dealer-installed keyless entry system or security system 199601 Prelude with dealer-installed security system 200004 S2000 with dealer-installed security system 200004 Insight with dealer-installed security system 200304 Pilot LX with dealer-installed keyless entry system or security system

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0).

98-011

7 of 21

4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

1997 Accord SE with factory-installed security system

P/N 72147-SY1-X01 H/C 4822789

199802 Accord EX with factory-installed security system 2000 and 2002 Accord SE with factoryinstalled security system
FCC ID: KOBUTAH2T CANADA 1983 102 297

UT Automotive

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode.
(Not interchangeable with CR-V and S2000 remote transmitter)

Transmitter Identification The transmitter for the 199899 Accord and the 200002 Accord look identical, but they are not interchangeable. The 199899 transmitter works the doors of a 200002 Accord, but it does not open the trunk. If you are not sure which transmitter you have, press and hold the trunk release button while looking at the LED. The LED on the 199899 transmitter comes on in about 1.1 seconds. The LED on the 200002 transmitter comes on in about 0.5 second.

8 of 21

98-011

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

200304 Accord LX and EX with factoryinstalled keyless entry system

P/N 35118-SDA-A11 H/C 7198914

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR1616. Each transmitter uses one battery.

98-011

9 of 21

199704 CR-V LX with dealer-installed keyless entry system 199804 CR-V EX with factory-installed keyless entry system 200001 CR-V SE with factory-installed keyless entry system 200004 S2000 with factory-installed keyless entry system 200204 CR-V with dealer-installed security system
199798 CR-V LX P/N 08E61-S10-100 H/C 5299292 1998 CR-V EX P/N 72147-S10-A51 H/C 5771746 199901 CR-V LX P/N 08E61-S10-101 H/C 6132963 199901 CR-V EX 2000--01 CR-V SE P/N 72147-S10-A52 H/C 6088074 200204 CR-V P/N 72147-S9A-A01 H/C 6240220 S2000 P/N 72147-S2A-A01 H/C 62402290
(Not interchangeable with 199802 Accord remote transmitter)

5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

MADE IN JAPAN

BATTERY
CR2025

199900 Odyssey EX with factory-installed keyless entry system or dealer-installed security system 200104 Odyssey EX models with factoryinstalled security system

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. Program the transmitters within 10 seconds. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2.

PA N I C

Transmitter Identification The 199900 transmitter is not interchangeable with the 200104 transmitter. To tell them apart, look at the FCC ID on the back. 199900 FCC ID: E4EG8DN 200104 FCC ID: OUCG8D-440H-A Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased.

10 of 21

98-011

 Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

199901 Prelude with factory-installed keyless entry system

98-011

11 of 21

198891 Prelude with dealer-installed security system

1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only through Tech Line. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

Programming the Transmitter This transmitter is not programmable. Ordering a Transmitter This transmitter is no longer available. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses two batteries.

199799 EV Plus with factory-installed security system

200004 Insight with factory-installed keyless entry system

P/N 39950-S73-A01 H/C 5405352

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode. You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode.

Programming the Transmitter NOTES: The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased. Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode.

12 of 21

98-011

 You must complete steps 16 within 4 seconds of the previous step to keep the system from exiting the programming mode. 1. Turn the ignition switch to ON (II). 2. Press the Lock or Unlock button on one of the transmitters. (An unprogrammed transmitter can be used for this step.) 3. Turn the ignition switch to LOCK (0). 4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2. 5. Turn the ignition switch to ON (II). 6. Press the Lock or Unlock button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode. 7. Within 10 seconds, press the Lock or Unlock button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitters code. 8. Turn the ignition switch to LOCK (0) to exit the programming mode. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

To clear a lost or stolen transmitter from the systems memory, program a transmitter four times. This will remove the missing transmitter from memory, since only four transmitters can be accepted. Programming the Transmitter 1. Locate the security system control unit under the drivers seat. 2. Rub your finger over the label on the top of the control unit until you find the depression. Once you find it, push your finger through the label to expose the hole underneath. Inside the hole is a square, yellow button; this is the programming button.

CONTROL UNIT

PROGRAMMING BUTTON
3. Turn the ignition switch to ON, then turn it to LOCK. 4. Press and hold the programming button. Check that the security siren emits four separate chirps followed by a five-chirp burst. This confirms that the system is in programming mode. The siren then emits prompting chirps at 3-second intervals. 5. Release the programming button. 6. After a prompting chirp, press the LOCK button on the transmitter. Verify that the siren emits a confirmation chirp to confirm that the transmitters code was accepted by the control unit. If you wait more than 30 seconds after the prompting chirp before programming a transmitter, or wait more than 30 seconds between programming transmitters, the siren emits three chirps and the system exits the programming mode. 7. To program additional transmitters, wait for another prompting chirp, then press the LOCK button. (You can program up to four transmitters per vehicle.)

199495 Passport (except 1995) with dealerinstalled security system

P/N 2-91309-401-0, H/C 4553012

NOTES: The system uses a stacking-type memory that accepts up to four transmitters. If you program a fifth transmitter, the memory for the first transmitter is pushed out, and it will no longer work.

98-011

13 of 21

8. To exit the programming mode, turn the ignition switch to ON, then turn it to LOCK. 9. Test all the transmitters. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is 23-144 (Radio Shack), A-23 (Eveready), or MS-21/MN-21 (Duracell). Each transmitter uses one battery.

2. Turn the ignition switch to ON. 3. Use a pen or pencil to press and hold the green programming button on the side of the control unit. When the security system LED on the instrument panel comes on, release the programming button. (Steps 3 and 4 must be done within 5 seconds of each other.)

PROGRAMMING BUTTON

199697 Passport with dealer-installed security system

4. Press and release the top button on the transmitter. Verify that the LED goes out, the siren chirps once, and the front sidemarker lights flash to confirm that the transmitters code was accepted by the control unit. 5. Turn the ignition switch to LOCK, then to ON.
P/N 2-91101-681-0, H/C 5029012

NOTES: The system uses a stacking-type memory that accepts up to two transmitters. If you program a third transmitter, the memory for the first transmitter is pushed out, and it will no longer work. To clear a lost or stolen transmitter from the systems memory, program a transmitter two times. This will remove the missing transmitter from memory, since only two transmitter codes can be accepted. Another way to clear a lost or stolen transmitter is to erase all transmitter codes and then reprogram them. To do this, refer to the security system owners manual. Programming the Transmitter 1. Move the drivers seat forward. Locate the security system control unit mounted on the floor underneath the seat.

6. Press and hold the green programming button on the side of the control unit until the LED on the instrument panel begins to flash, then release the button. (Steps 6 and 7 must be done within 5 seconds of each other.) 7. Press and release the bottom button on the transmitter. Verify that the LED goes out, the siren chirps twice, and the front sidemarker lights flash twice to confirm that the transmitters code was accepted by the control unit. 8. Turn the ignition switch to LOCK. Test the transmitter you just programmed. If it doesnt work, repeat steps 2 thru 7. 9. If you have another transmitter to program, repeat steps 2 thru 7. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2025. Each transmitter uses one battery.

CONTROL UNIT

14 of 21

98-011

199802 Passport with factory-installed security system

Procedure Two (adds transmitters) 1. Open the drivers door. 2. Turn the ignition switch to the ACC position and then to the LOCK position three times. (This step must be completed within 10 seconds, or the system will not enter the programming mode.) 3. Within 10 seconds, close and open the door two times. 4. Turn the ignition switch to the ACC position and then to the LOCK position three times. Close and open the door. (Complete this process within 10 seconds.) Verify that the power door locks cycle once to confirm that the system is in programming mode. 5. Within 20 seconds, press the LOCK button on the transmitter you are programming. Verify that the door locks cycle once. 6. Within 20 seconds, press the UNLOCK button on the transmitter. Verify that the door locks cycle once to confirm that the system has accepted the transmitters code. Turning the Audible Chirp On/Off (199899 only) NOTE: On 0002 Passports, the audible chirp sounds only when you push the LOCK button on the transmitter a second time. 1. Open the drivers door, then insert the key in the drivers door lock. 2. Turn the key to the LOCK position, then to the UNLOCK position. Repeat this two more times. (Complete this procedure within 10 seconds.) 3. Within 10 seconds, close and open the door two times. 4. Within 10 seconds, turn the key to the LOCK position, and then to the UNLOCK position, three times. Close and open the door once. Verify that the power door locks cycle once to confirm that the chirp has been turned on/off. Ordering a Transmitter Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures. Batteries for the Transmitter The battery number is CR2016. Each transmitter uses two batteries.

P/N 8-97149-392-0, H/C 5743000

Programming the Transmitter To program the transmitters, use one of these two procedures: Procedure One cancels all learned transmitter codes and adds one new transmitter. None of the previously programmed transmitters will work. Use this programming procedure only if all transmitters were lost or stolen, or if a new control unit has been installed. Procedure Two adds additional transmitters without cancelling any of the previously learned codes. The system will accept up to four transmitters. Procedure One (cancels all codes, adds one new transmitter) 1. Open the drivers door. 2. Turn the ignition switch to the ACC position and then to the LOCK position three times. (This step must be completed within 10 seconds, or the system will not enter the programming mode.) 3. Within 10 seconds, close and open the door two times. 4. Turn the ignition switch to the ACC position and then to the LOCK position five times. Close and open the door. (Complete this process within 10 seconds.) Verify that the power door locks cycle once to confirm that the system is in programming mode. 5. Within 20 seconds, press the LOCK button on the transmitter you are programming. Verify that the door locks cycle once. 6. Within 20 seconds, press the UNLOCK button on the transmitter. Verify that the door locks cycle once to confirm that the system has accepted the transmitters code.

98-011

15 of 21

Remote Transmitter Quick Reference Guide

Model Accord Application 199093 (except 5-door) with dealerinstalled security system Remote Transmitter P/N 08E50-SM4-110 H/C 3524733 Battery CR2025 (one required)

199193 5-door EX with factoryinstalled keyless entry system or dealer-installed security system

P/N 04808-SM5-A01 H/C 3721735

Not replaceable

199193 5-door LX with dealerinstalled security system

Order from Kenwood USA

CR1220 (two required)

199495 with dealer-installed security system

P/N 08E51-SV4-1M001 H/C 4285565

CR2025 (one required)

199497 5-door EX with factoryinstalled keyless entry system

P/N 72147-SV5-A02 H/C 5030176

CR2016 (two required)

199697 with dealer-installed security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

1997 SE with factory-installed security system

P/N 72147-SY1-X01 H/C 4822789

CR2025 (one required

199802 DX & LX with dealer-installed keyless entry system or security system

P/N 08E61-S01-100 H/C 4834834

CR2025 (one required)

199899 EX with factory-installed security system

P/N 72147-S84-A01 H/C 5441910

CR2025 (one required)

16 of 21

98-011

Model Accord (contd)

Application 200002 EX with factory-installed security system 2000 and 2002 SE with factory-installed security system 200304 DX with dealer-installed security system

Remote Transmitter P/N 72147-S84-A03 H/C 6249049

Battery CR2025 (one required)

P/N 08E61-S5D-1M002 H/C 6754550

CR2025 (one required)

200304 LX & EX with factory-installed keyless entry system

P/N 35118-SDA-A11 H/C 7198914

CR1616 (one required)

Civic

199293 with dealer-installed security system

P/N 08E50-SM4-110 H/C 3524733

CR2025 (one required)

199495 with dealer-installed security system

P/N 08E51-SV4-1M001 H/C 4285565

CR2025 (one required)

199698 with factory-installed keyless entry system or dealer-installed keyless entry system or security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

199900 with factory-installed keyless entry system or dealer-installed keyless entry system or security system

P/N 72147-S04-A02 H/C 6134746

CR2025 (one required)

200103 EX with factory-installed keyless entry system or dealer-installed security system 2004 LX & EX with factory-installed keyless entry system or dealer-installed security system 200304 Hybrid with factory-installed keyless entry system or dealer-installed security system

P/N 72147-S5A-A01 H/C 6457170

CR2025 (one required)

98-011

17 of 21

Model Civic (contd)

Application 200103 (except EX) with dealer-installed keyless entry system or security system 2004 (except LX & EX) with dealer-installed keyless entry system or security system 200204 Si with factory-installed keyless entry system or dealer-installed security system

Remote Transmitter P/N 08E61-S5D-1M002 H/C 6754550

Battery CR2025 (one required)

P/N 72147-S5T-A01 H/C 6966949

CR2025 (one required)

del Sol

1993 with dealer-installed security system

P/N 08E50-SM4-110 H/C 3524733

CR2025 (one required)

199495 with dealer-installed security system

P/N 08E51-SV4-1M001 H/C 4285565

CR2025 (one required)

199697 with dealer-installed security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

Insight

200004 with factory-installed keyless entry system

P/N 72147-S3Y-A01 H/C 6348320

CR2025 (one required)

200004 with dealer-installed security system

P/N 08E61-S01-100 H/C 4834834

CR2025 (one required)

Prelude

198891 with dealer-installed security system

Discontinued

CR2025 (two required)

199293 with dealer-installed security system

P/N 08E50-SM4-110 H/C 3524733

CR2025 (one required)

18 of 21

98-011

Model Prelude (contd)

Application 199495 with dealer-installed security system

Remote Transmitter P/N 08E51-SV4-1M001 H/C 4285565

Battery CR2025 (one required)

199601 with dealer-installed security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

199901 with factory-installed keyless entry system

P/N 72147-S30-A01 H/C 6016802

CR2025 (one required)

S2000

200004 with factory-installed keyless entry system

P/N 72147-S2A-A01 H/C 6240220

CR2025 (one required)

200004 with dealer-installed security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

CR-V

199798 LX with dealer-installed keyless entry system

P/N 08E61-S10-100 H/C 5299292

CR2025 (one required)

199701 with dealer-installed security system

P/N 39950-S01-A01 H/C 4811352

CR2025 (one required)

1998 EX with factory-installed keyless entry system

P/N 72147-S10-A51 H/C 5771746

CR2025 (one required)

199900 CR-V LX with dealer-installed keyless entry system

P/N 08E61-S70-101 H/C 6132963

CR2025 (one required)

98-011

19 of 21

Model

Application 199901 EX with factory-installed keyless entry system 200001 SE with factory-installed keyless entry system 200204 with factory-installed keyless entry sytem or dealer-installed security system

Remote Transmitter P/N 72147-S10-A52 H/C 6088074

Battery CR2025 (one required)

P/N 72147-S9A-A01 H/C 6896542

CR2025 (one required)

Element

2003 with dealer-installed keyless entry system or security system 2004 DX & LX with dealer-installed keyless entry system or security system 2004 EX with factory-installed keyless entry system

P/N 08E61-S5D-1M001 H/C 6718944

CR2025 (one required)

P/N 72147-S5T-A01 H/C 6966949

CR2025 (one required)

Odyssey

1995 with dealer-installed security system

P/N 08E51-SV4-1M001 H/C 4285565

CR2025 (one required)

199598 EX with factory-installed keyless entry system

P/N 72147-SV5-A02 H/C 5030176

CR2025 (one required)

199604 LX with dealer-installed keyless entry system or security system 199698 EX with dealer-installed security system 199900 EX with factory-installed keyless entry system or dealer-installed security system
PA N I C

P/N 08E61-S01-100 H/C 4834834

CR2025 (one required)

P/N 72147-S0X-A01 H/C 5932702

CR2025 (one required)

200104 EX models with factoryinstalled security system

P/N 72147-S0X-A02 H/C 6554174

CR2025 (one required)

PA N I C

20 of 21

98-011

Model Passport

Application 199495 (except 1995) with dealerinstalled security system

Remote Transmitter P/N 2-91309-401-0 H/C 4553012

Battery Radio Shack 23-144 or Eveready A-23 or Duracell MS-21/ MN-21 CR2025 (one required)

199697 with dealer-installed security system

P/N 2-91101-681-0 H/C 5029012

199802 with factory-installed security system

P/N 8-97149-392-0 H/C 5743000

CR2016 (two required)

Pilot

200304 LX with dealer-installed keyless entry system or security system

P/N 08E61-S01-100 H/C 4834834

CR2025 (one required)

200304 EX models with factoryinstalled security system

P/N 72147-S5A-A01 H/C 6457170

CR2025 (one required)

EV Plus

199799 with factory-installed security system

P/N 39950-S73-A01 H/C 5405352

CR2025 (one required)

21 of 21

98-011