This document describes a project proposal for an ATM security system using GSM and MEMS. The system is designed to detect irregular movement of the ATM during a theft attempt using a MEMS sensor. If movement is detected, the microcontroller will activate to shut the ATM door using a stepper motor and send an SMS alert using GSM to notify security. The system aims to stop robbery and allow security to respond quickly. Key components include a power supply, microcontroller, MEMS sensor, GSM modem, motor, and other interfacing circuits.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
This document describes a project proposal for an ATM security system using GSM and MEMS. The system is designed to detect irregular movement of the ATM during a theft attempt using a MEMS sensor. If movement is detected, the microcontroller will activate to shut the ATM door using a stepper motor and send an SMS alert using GSM to notify security. The system aims to stop robbery and allow security to respond quickly. Key components include a power supply, microcontroller, MEMS sensor, GSM modem, motor, and other interfacing circuits.
This document describes a project proposal for an ATM security system using GSM and MEMS. The system is designed to detect irregular movement of the ATM during a theft attempt using a MEMS sensor. If movement is detected, the microcontroller will activate to shut the ATM door using a stepper motor and send an SMS alert using GSM to notify security. The system aims to stop robbery and allow security to respond quickly. Key components include a power supply, microcontroller, MEMS sensor, GSM modem, motor, and other interfacing circuits.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
This document describes a project proposal for an ATM security system using GSM and MEMS. The system is designed to detect irregular movement of the ATM during a theft attempt using a MEMS sensor. If movement is detected, the microcontroller will activate to shut the ATM door using a stepper motor and send an SMS alert using GSM to notify security. The system aims to stop robbery and allow security to respond quickly. Key components include a power supply, microcontroller, MEMS sensor, GSM modem, motor, and other interfacing circuits.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt
You are on page 1/ 5
JIMMA UNIVESITY
JIMMA INSTITUTE OF TECHNOLOGY
DEPARTMENT OF ELECTRICAL AND COMPUTER NGINEERING
A Project Proposal on: ATM SECURITY SYSTEM USING GSM
in partial fulfillment of the requirements for the degree award of Bachelor of Science in
Submitted to: Department of Electrical and Computer Engineering
Advisor:
ATO Musa Hayato
Submission Date: April 4, 2012
INTRODUCTION The overview of this project is to design MEMS and GSM based ATM SECURITY system using AT89S52. The Project ATM security system using GSM and MEMs module is designed using MEMS technology. According to this technology the communication takes place between two devices MEMS and microcontroller. The MEMS is a sensor device which identifies the tilt produced by the ATM machine due to the irregular movement that occur during theft. This project makes best use of MEMS as a sensor device which identifies the tilt produced by the ATM machine due to the irregular movement that occur.. The project basically consists of a MEMS sensor which identifies the tilt by the machine and activates the microcontroller to start the following sequence in which shutting the door using stepper motor and sending SMS to vigilance system using GSM is involved.
SIGNIFICANCE THE PROJECT
This System stops any sort of robbery by taking MEMS as its input functional bock. Its the MEMS that is activating the total project by identifying the tilt caused by the thief during breaking down the ATM machine. Once the micro controller is activated the following sequence is started which involves shutting of the door using stepper motor and alerting the vigilance system by a SMS using GSM.
BLOCK DIAGRAMM OF THE PROJECT
POWER SUPPLY A D C 0
A T 8 9 S
LCD DISPLA
MEMS SENSOR 8 0 4
GSM MODEM
MAX232
5 2
RELAY
MOTOR
The hardware involved in this project is a Power Supply, a LCD to display the concerned information, a GSM is interfaced to the Microcontroller through MAX 232, and MEMS is interfaced through ADC 0804. While execution, the tilt is identified by the MEMS and it activates the microcontroller. The microcontroller then starts the following sequence; it gives command to shut down the door in order to avoid the thief to run away and also a SMS is sent to the vigilance system to alert them so that they can approach to the place as soon as possible to catch the burglar. This Project mainly consists of Power Supply section, Microcontroller section, MEMS section, GSM section, LCD display section, Max 232 serial driver section, ADC 0804 section, Motor section and Relay section. Some of the functions of basic sections are: The power supply section is used for supplying Power to all the sections. It converts 220v ac line voltage into 9v DC. The Microcontroller section forms the heart of the project because it controls the devices being interfaced and communicates with the devices according to the program being written in to it. The MEMS section is the input functional block which is used to identify the tilt that are
occurred in the ATM machine when a thief tries to break open the ATM machine. GSM (Global System for Mobile communications) section is a cellular network, which means that mobile phones connect to it by searching for cells in the immediate vicinity, so that whenever the thief tries to break the machine it tries to call local villagers by using GSM network.
