KALLEY

K-TV21PF & K-TV29PF

with NTSC/PALm/PALn
S
SSE
EER
RRV
VVI
IIC
CCE
EE M
MMA
AAN
NNU
UUA
AAL
LL
COLOR TELEVISION
.
2
CONTENTS
1. safety precautions3
2. block diagram
and PHILIPS UOC functional difference between the various IC versions .4
3 Replacement of memory IC7
4 Service adjustment...7
5 ICs functional description11
6 Test point waveform.15
7 All ICs/transistors voltages.16
8 Purity / convergence adjustment..17
.
3
SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many
circuits and components specially for safety purposes. For
continued protection, no changes should be made to the
original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to those
used in the original circuits. Service should be performed by
qualified personnel only.
2. Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacturer of responsibility for personal injury or property
damage resulting therefrom.
3. Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics
are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by
using replacement components rated for higher voltage,
wattage, etc. Replacement parts which have these special
safety characteristics are identified in the parts list of
Service manual. Electrical components having such
features are identified by shading on the schematics
and by ( ) on the parts list in Service manual. The
use of a substitute replacement which does not have the
same safety characteristics as the recommended
replacement part shown in the parts list of Service manual
may cause shock, fire, or other hazards
4. Dont short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side
ground when repairing. Some models power circuit is
partly different in the GND. The difference of the GND is
shown by the LIVE: ( ) side GND, ISOLATED (NEUTRAL)
: ( ) side GND and EARTH : ( ) side GND. Dont short
between the LIVE side GND and ISOLATED (NEUTRAL)
side GND or EARTH side GND and never measure with a
measuring apparatus (oscilloscope etc.) the LIVE side GND
and ISOLATED (NEUTRAL) side GND or EARTH side GND
at the same time. If above note will not be kept, a fuse or
any parts will be broken.
5. If any repair has been made to the chassis, it is
recommended that the B1 setting should be checked or
adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).
6. The high voltage applied to the picture tube must conform
with that specified in Service manual. Excessive high
voltage can cause an increase in X-Ray emission, arcing
and possible component damage, therefore operation under
excessive high voltage conditions should be kept to a
minimum, or should be prevented. If severe arcing occurs,
remove the AC power immediately and determine the cause
by visual inspection (incorrect installation, cracked or
melted high voltage harness, poor soldering, etc.). To
maintain the proper minimum level of soft X-Ray emission,
components in the high voltage circuitry including the
picture tube must be the exact replacements or alternatives
approved by the manufacturer of the complete product.
7. Do not check high voltage by drawing an arc. Use a high
voltage meter or a high voltage probe with a VTVM.
Discharge the picture tube before attempting meter
connection, by connecting a clip lead to the ground frame
and connecting the other end of the lead through a 10k
2W resitor to the anode button.
8. When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead
dress in the high voltage circuit area. Where a short circuit
has occurred, those components that indicate evidence of
overheating should be replaced. Always use the
9. manufacturers replacement components.
10. Isolation Check
(Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an
isolation check on the exposed metal parts of the cabinet
(antenna terminals, video/audio input and output terminals,
Control knobs, metal cabinet, screwheads, earphone jack,
control shafts, etc.) to be sure the product is safe to operate
without danger of electrical shock.
11. The surface of the TV screen is coated with a thin film which
can easily be damaged. Be very careful with it when handle
the TV.Should the TV screen become soiled, wipe it with a
soft dry cloth. Never rub it forcefully. Never use any cleaner
or detergent on it.
(1) Dielectric Strength Test
The isolation between the AC primary circuit and all metal
parts exposed to the user, particularly any exposed metal
part having a return path to the chassis should withstand a
voltage of 3000V AC (r.m.s.) for a period of one second.
(Withstand a voltage of 1100V AC (r.m.s.) to an
appliance rated up to 120V, and 3000V AC (r.m.s.) to an
appliance rated 200V or more, for a periode of one second.)
This method of test requires a test equipment not generally
found in the service trade.
(2) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use
a line isolation transformer during this check.). Using a
Leakage Current Tester, measure the leakage current
from each exposed metal part of the cabinet, particularly
any exposed metal part having a return path to the chassis,
to a known good earth ground (water pipe, etc.). Any
leakage current must not exceed 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.2mA AC
(r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet ( do not use
a line isolation transformer during this check.). Use an AC
voltmeter having 1000 ohms per volt or more sensitivity in
the following manner. Connect a 1500 10W resistor
paralleled by a 0.15F AC-type capacitor between an
exposed metal part and a known good earth ground (water
pipe, etc.). Measure the AC voltage across the resistor with
the AC voltmeter. Move the resistor connection to each
exposed metal part, particularly any exposed metal part
having a return path to the chassis, and measure the AC
voltage across the resistor. Now, reverse the plug in the AC
outlet and repeat each measurement. Any voltage
measured must not exceed 0.75V AC (r.m.s.). This
corresponds to 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.3V AC
(r.m.s.).
This corresponds to 0.2mA AC (r.m.s.)
.
4
2 TV Block diagram for PALm/PALn
TUNER
SAW
IF IN Y IN
RF AGC V IN
BAND1
BAND2 U IN
CVBSINT
CHROMA
IFVO OUT
CVBS/Y IN
SDA
SCL
AUDIO OUT IK
RGB OUT
V OUT H OUT
S
TRAP
Vo
V2i
V1i
Y
Cr
Cb
ARi2
ARi1
ALi2
ALi1
S-VHS
24C04
POWER
UNIT
130V
24V
16V
8V
5V
3.3V
CRT PCB
V IN
TDA8351
V OUT
DY
H IN
H OUT
H OUT
200V
+15V
-15V
SCREEN
FOCUS
TDA9361
Vi1
OUT1-
OUT1+
Vi2
OUT2-
OUT2+
AN7522
CRT
ALo
ARo
C
Y
4052
TDA9859
A

O
U
T
R
A

O
U
T
L
M
A
I
N

L
M
A
I
N

R
S
D
A
/
S
C
L
A
V
2

R
A
V
2

R
M

O
U
T
R
M

O
U
T
L
A
V
1

L
A
V
2

L
7 4 5 1 2 6 7 8
XS303
5V
TDA9850
audio
audio
audio
audio
video
video
bus
bus
video
video
video
CD8145
EW
BTSC
.
5
PHILIPS UOC FUNCTIONAL DIFFERENCE BETWEEN THE VARIOUS IC VERSIONS
IC VERSION 9350 9351 9352 9353 9360 9361 9362 9363 9364 9365 9366 9367 9380 9381 9382 9383 9384 9385 9386 9387 9388 9389 9370 9373 9375 9377 9378
TV rang 90 90 90 110 90 90 110 110 110 110 90 90 90 90 90 110 110 110 110 90 110 110 90 110 110 90 110
Mono inter-carrier multi-standard
Sound demodulator (4.5-6.5MHz)
With switch able centre frequency

Audio switch
Automatic volume leveling
Automatic volume leveling or
Subcarrier output (for comb filter
applications)

QSS sound IF amplifier with
Separate input and AGC circuit

AM sound demodulator without
Extra reference circuit

PAL decoder
SECAM decoder
NTSC decoder
Horizontal geometry(E-W)
Horizontal and vertical zoom
ROM size 32-
64k
32-
64k
32-
64k
32-
64k
64-
128
64-
128
64-
128
64-
128
64-
128
64-
128
64-
128
64-
128
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
16-
64k
32-
55k
32-
55k
32-
55k
32-
55k
32-
55k
User RAM size 1k 1k 1k 1k 2k 2k 2k 2k 2k 2k 2k 2k 1k 1k 1k 1k 1k 1k 1k 1k 1k 1k 2.25 2.25 2.25 2.25 2.25
Teletext 1 p 1p 1p 1p 10p 10p 10p 10p 10p 10p 10p 10p
Closed captioning
Block diagram TDA93xX PS/N2 series with mono intercarrier sound demodulator
.
6
7
3.REPLACEMENT OF MEMORY IC
1. MEMORY IC.
This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and
deflection circuits.
When replacing memory IC, be sure to use IC written with the initial value of data.
2. PROCEDURE FOR REPLACING MEMORY IC
(1) Power off
Switch the power off and unplug the power cord from AC outlet.
(2) Replace IC
Be sure to use memory IC written with the initial data values.
(3) Power On
Plug the power cord into the AC outlet and switch the power On.
(4) Check and set SYSTEM default value:
1) Press QV key holding about 4 second and then press MENU1 key on the Remote control
unit. Or Press TEST key on the Remote control unit for factory used.
2) The TEST will be displayed on the screen.
3) Press digital key, (Mkey) and corresponding on-screen display will be appeared.
Some time PASSWORD on-screen display will be appeared, you need to input 828.
4) Check the setting value of the SYSTEM default value of Table below. If the value is different,
select items by [CH+]/[CH-] keys and set value by [VOL+]/[VOL-] keys.
5) Press STANDBY key again and return to the normal screen.
4.SERVICE ADJUSTMENT
B1 POWER SUPPLY
1. Receive normal colour bar signal.
2. Connect DC voltmeter to VD541- and isolated ground.
3. Adjust potentiometer in power unit to get the voltage as 110V 1.0V for 21 inch hereinafter,
130 1.0V for 25 inch upwards.
FOCUS ADJUSTMENT
1. Receive a crosshatch signal.
2. While watching the screen, adjust the FOCUS VR to make the vertical and horizontal lines as fine
and sharp as possible.
EW ADJUSTMENT(only upper 25 inch)
1. adjust VR433 for horizontal size, to get 90% of horizontal picture contents would be displayed on
CRT.
2. adjust VR432 for EW parabola, to straighten the vertical at the sides.
3. adjust VR431 for EW trapezium, to set the line at the sides vertical.
8
BUS CONTROL ADJUSTMENT
1. first color value set to 0, then Press TEST key on the Remote control unit of factory.
Press 0 to 9 key, (Mkey) and corresponding on-screen display will be appeared. But to enter M4-M9,
Must input passcord 828.
On TV screen TEST will be indicated, this means entered bus control mode.
And press following key, each function will be available.
3. may be intered TEST mode with remote control unit of user, press QV key and hold 4 seconds. and
then press MENU key, TV set may be entered TEST mode.
Remote Hand Unit keys
[M1] [M2] [M3]





[M0]
[M1] menu
MENU0 Geometrical adjustment
Receive PAL standard Complete pattern signal.
Adjustment steps
a) Adjust V. SLOPE, to the center horizontal line just appeare from half bottom shadow.
b) Adjust V. SIZE, to get 90% of vertical picture contents would be displayed on CRT.
c) Adjust V. SHIFT, the center horizontal line correspond to CRT vertical center.
d) Adjust H.SHIFT, to get the picture horizontal center correspond to CRT horizontal center.
Receive NTSC signal and repeat above [M0] and [M1] adjustment.
[M2] Menu
AGC Adjustment.
Receive 60dB(1mV)V
H
colour bar pattern signaladjust AGC valuevoltage from high to lowto noise
reduce gradually and just disappeared point.
[M3] Menu
CRTcut off and white balance adjustment.
Receive white signal.
a) CRT cut off adjustment.
1. Select SC, then automatically vertical scan will be stopped.
2. Adjust SCREEN control on Flyback transformer to get the darkest single horizontal line (red,
green, or blue, sometimes shows more yellow, more purple or more white).
b) White balance adjustment.
1. Select RD/BD menu.
2. Adjust RD/BD to get colour temperature as x=281, y=311
c) Sub-Brightness adjustment. (Use stair case signal)
1. Select SB menu.
2. Adjust SB to get the darkest step being cutoff.
MENU1
V.SLOPE 31
V.SHIFT 31
V. SIZE 31
V.S 31
H.SHIFT 31

C CC C C CC C C CC C
C CC C
C CC C C CC C
9
ICs Default Settings
a) TDA9370(STANDARD) EK cord=NTDA9370---2NA EK cord=NTDA9370---2NA EK cord=NTDA9370---2NA EK cord=NTDA9370---2NA
MI Items Variable Preset MI Items Variable Preset
M1 FREQUENCY 50HZ M5 SUB Contrast 0~63 63
V.SLOPE 0~63 31 SUB color 0~63 63
V.SHIFT 0~63 31 SUB sharp 0~63 63
V.SIZE 0~63 31 SUBTINT 0~15 15
V.S 0~63 31 SUB Volume 0~63 63
H.SHIFT 0~63 31
OSD. V.POS 0~63 53 M6 OSO ON/OFF ON
OSD.H.POS 0~59 15 AGC-SPEED 0~3 2
PROGRAM NO FFI ON/OFF OFF
FSL ON/OFF ON
M2 AGC Takeover 0~63 25 FMWS ON/OFF OFF
SHIPMODE PRO 0~3 0
NTSC MX USA
M3 BT 0~63 48
CT 0~63 48 M7 STANDARD BRI 0~63 48
SC OFF STANDARD CONT 0~63 48
RB 0~63 32 STANDARD COL 0~63 48
GB 0~63 32 SHARP BRI 0~63 48
RD 0~63 32 SHARP CONT 0~63 63
GD 0~63 32 SHARP COL 0~63 32
BD 0~63 32 SOFT BRI 0~63 32
SB 0~63 40 SOFT CONT 0~63 32
SOFT COL 0~63 32
M4 BTSC-MODE STEREO
UOC VOLUME 0~63 34 M8 AV CFG* 0~8 3
BTSC-ST 0~15 15 YDLY PAL 0~15 12
BTSC-SP 0~15 15 YDLY AV 0~15 12
BTSC-LI 0~15 12 SC BRIGHT 0~63 10
BTSC-A1 0~31 0 CATHODE LEVEL 0~15 10
BTSC-A2 0~31 31 HEADPHONE ON/OFF OFF
BTSC-TC 0~7 3 VM OPTION ON/OFF OFF
BTSC-STS 0~1 0
BTSC-ADJ AUTO M9 START ON 0~2 0
START TIME 0~15 8
10
5. ICs functional description
UOC TDA93XX
SYMBOL PIN DESCRIPTION
STAND BY output. 1 In STAND BY mode, high level (Power OFF).
For Power ON this pin will be reduced to low.
SCL 2 I
2
C-bus clock line
SDA 3 I
2
C-bus data line
TUNING 4 tuning Voltage (Vt) PWM output
P3.0/NTSC SW 5 Port 3.0 or NTSC output/SCART SW input, Forced NTSC selection,
Low-level output, otherwise High output.
KEY 6 Control keys input *3
VOL 7 Sound Volume control PWM output
MUTE 8 Sound mute output
VSSC/P 9 Digit ground for -controller core and periphery
BAND1 10 Tuner Band selection output
BAND2 11 Tuner Band selection output
VSSA 12 Analog ground of teletext decoder and digital ground of TV-processor
SECPLL 13 SECAM PLL decoupling
VP2 14 2
nd
supply voltage TV-processor(+8V)
DECDIG 15 decoupling digital supply of TV-processor
PH2LF 16 Phase-2 filter
PH1LF 17 Phase-1 filter
GND3 18 Ground 3 for TV-processor
DECBG 19 Band gap decoupling
AVL/EWD 20 Automatic volume leveling /EAST-WEST drive output
VDRB 21 Vertical drive B output
VDRA 22 Vertical drive A output
IFIN1 23 IF input 1
IFIN2 24 IF input 2
IREF 25 Reference current input
VSC 26 Vertical sawtooth capacitor
TUNER AGC 27 Tuner AGC output
AUDEEM/SIFIN1 *1 28 Audio deemphasis or SIF input
DECSDEM/SIFIN2 29 decoupling sound demodulator or SIF input 2
GND2 30 ground 2 for TV processor
SNDPLL/SIFAGC *1 31 narrow band PLL filter or AGC sound IF
AVL/SNDIF/REF0/
AMOUT *1
32 Automatic Volume Levelling / sound IF input / subcarrier reference output / audio
deemphasis
HOUT 33 horizontal output
FBISO 34 flyback input/sandcastle output
11
AUDEXT/QSSO/
AMOUT *1
35 external audio output / QSS intercarrier out
EHTO 36 EHT/overvoltage protection input
PLL IF 37 IF-PLL loop filter
IFVO/SVO 38 IF video output / selected CVBS output
VP1 39 supply voltage TV processor
CVBS INT 40 internal CVBS input
GND1 41 ground for TV processor
CVBS/Y 42 CVBS/Y input
CHROMA 43 C input
AUDOUT/AMOUT *1 44 audio output /AM audio output (volume controlled)
INSSW2 45 2nd RGB / YUV insertion input
R2/VIN 46 2nd R input / V (R-Y) input / PR input
G2/YIN 47 2nd G input / Y input
B2/UIN 48 2nd B input / U (B-Y) input / PB input
BCLIN 49 beam current limiter input
BLKIN 50 black current input / V-guard input
RO 51 Red output
GO 52 Green output
BO 53 Blue output
VDDA 54 analog supply of Closed Caption decoder and digital supply of TV-processor
(3.3 V)
VPE 55 OTP Programming Voltage
VDDC 56 digital supply to core (3.3 V)
OSCGND 57 oscillator ground supply
XTALIN 58 crystal oscillator input
XTALOUT 59 crystal oscillator output
RESET 60 reset
VDDP 61 digital supply to periphery (+3.3 V)
P1.0/INT1 62 TV/AV (AV1) / AV2 /S-VHS mode Output.
P1.1/T0 63 TV/AV (AV1) / AV2 /S-VHS mode Output.
P1.2/INT0 64 Remote control signal input.
Note
1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator
/QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given in
table 1.
2. the vertical guard function can be controlled via pin 49 or pin 50. the selection is made by means of the
IVG bit in subaddress 2BH.
12
TABLE 1
IC version FM-PLL version QSS version
East-West
Y/N
N Y N Y
CMB1/CMB
0 bits
00 01/10/1
1
00 01/10/1
1
00 01/10/11 00 01/10/11
AM bits - - - - - 0 1 - 0 1
Pin 20 AVL EWD AVL EWD
Pin 28 AUDEEM SIFIN1
Pin 29 DECSDEM SIFIN2
Pin 31 SNDPLL SIFAGC
Pin 32 SNDIF(1
)
REFO(2) AVL/SNDIF(1
)
REFO(2) AMOUT REFO(2) AMOUT REFO(2)
Pin 35 AUDEXT AUDEXT QSS
O
AMOU
T
AUDEXT QSS
O
AMOU
T
Pin 44 AUDOUT Controlled AM or audio out
Note
1. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This
function is selected by means of SIF bit in subaddress 28H.
2. the reference output signal is only available for the CMB1/CMB0 setting of 0/1. for the other settings this pin is
a switch output(see also 5 table 67).
Pin No. 6: Control keys input (Max. Limit voltage)
Function POWER MENU TV/AV V- V+ P- P+
Voltage 0 0.4125 0.825 1.2375 1.65 2.0625 2.475
13
AN7522/7523 Function : audio output
Symbol PIN Function Symbol PIN Function
Vcc 1 Power supply GND 7 ground
Out 1 (+) 2 Ch 1 output (+) In 2 8 Ch 2 input
GND(out 1) 3 Ch 1Ground VOL 9 Volume Control
Out 1 (-) 4 Ch 1 output (-) Out 2 (-) 10 Ch 2 output (-)
Standby 5 Mute input GND(out 2) 11 Ch 2 Ground
In 1 6 Ch 1 input Out 2 (+) 12 Ch 2 output (+)
Note: AN7523 is pin 1 to 9, AN7522 is pin 1 to 12.
LA78040/78045 Function : vertical output
Symbol PIN Function Symbol PIN Function
INV IN 1 Input V OUT 5 Vertical output
VCC1 2 Power VCC2 6 Output power supply
PUMP UP 3 Pump up power NON INV IN 7 Negative feedback
GND 4 Ground
TDA9859 Function : Universal Sound processor
Symbol Pin Function Symbol Pin Function
AV1L 1 AV1 Audio Left input AV1R 32 AV1 Audio input Right
P1 2 Not used P2 31 Not used
MAINL 3 Main Audio Left input AV2R 30 AV2 Audio input Right
CSMO 4 Smoothing Capacitor CPS1 29 Pseudo stereo Cap. 1
MAINR 5 Main Audio Right input AV2L 28 AV2 Audio input Left
VP 6 Power Supply CPS2 27 Pseudo stereo Cap. 2
OUT R 7 Right Output OUT L 26 Left Output
GND 8 Ground MAD 25 Not used (GND)
LINOR 9 Line Output Right LINOL 24 Line Output Left
LINIR 10 Line Input Right LINIL 23 Line Input Left
CBR1 11 Bass Cap. Right 1 CBL1 22 Bass Cap. Left 1
CBR2 12 Bass Cap. Right 2 CBL2 21 Bass Cap. Left 2
Headphone R 13 Headphone-R output Headphone L 20 Headphone-L output
CTR 14 Treble Cap. Right CTL 19 Treble Cap. Left
MAINOR 15 Main Audio out Right MAINOL 18 Main Audio out Left
SCL 16 I2C Bus clock SDA 17 I2C Bus data
CD 8145 Function : EW parabola correction
Symbol PIN Function Symbol PIN Function
Keystone input 1 Trapezium
correction input
NON INV IN 8 Non-inverting 100 ua
Current sink
Sawtooth input 2 frame sawtooth
current input
INV IN 7 Parabola output
Inverting input
I ref 3 Current reference VCC 6 VCC
GND 4 Ground Output 5 Output
14
6. Test point Waveforms
V451 C
5Vpp 0.9Vpp
1000Vpp
1.3Vpp
H
H
1Vpp
V
H H
CRT KB CRT KG CRT KR
95Vpp 95Vpp 95Vpp
H
H H
T511 PIN7 HEATER
300Vpp 22Vpp
H H
V451 B
2.7Vpp
TDA93XX PIN53
2.5Vpp 2.5Vpp 3.8Vpp
H H
H
TDA93XX PIN52 TDA93XX PIN51
TDA93XX PIN33 TDA93XX PIN34
0.8Vpp
V
TDA93XX PIN21 TDA93XX PIN22
TDA93XX PIN59
1.2Vpp 2.6Vpp
H H
TDA93XX PIN40
TDA93XX PIN38
15
7. IC voltages
TDA93XX
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
V 2.8 3.8 3.6 3.3 3.5 3.5 0.1 0.1 0 5.4 0.1 0 2.3 8 5 3
PIN 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
V 4 0 4 0.9 0.7 0.8 1.9 1.9 3.9 3.8 1.6 3.2 3.4 0 2.4 0.1
PIN 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
V 0.6 0.5 3.7 1.7 2.4 3.1 8 3.8 0 3.4 1.5 3.6 2.3 2.6 2.6 2.6
PIN 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
V 2.3 7.2 2.7 2.7 2.7 3.5 0 3.5 0.1 1.7 1.8 0 3.5 0.1 0.1 5
LA76040
PIN 1 2 3 4 5 6 7
V 0.7 15 -12 -15 0.3 15.9 -0.07
AN 7522
PIN 1 2 3 4 5 6 7 8 9 10 11 12
V 12 7 0 7 3.3 1.4 0 1.4 0 7 0 7
TDA9859
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14
V 4.0 0 4.0 8.0 4.0 8.0 4.0 0 4.0 4.0 4.0 4.0 4.0 4.0
PIN 15 16 17 18 19 20 21 22 23 24 25 26 27 28
V 4.0 4.5 4.6 4.0 4.0 4.0 4.0 4.0 4.0 4.0 0 4.0 4.0 4.0
PIN 29 30 31 32
V 4.0 4.0 0 4.0
CD 8145
PIN 1 2 3 4 5 6 7 8
V 1.6 1.8 8.2 0 9.4 26.5 10 10
16
8. PURITY / CONVERGENCE ADJUSTMENT
PURITY ADJUSTMENT
1. Demagnetize CRT with the demagnetizer.
2. Loosen the retainer screw of the deflection yoke.
3. Remove the wedges.
4. Input a green raster signal from the signal generator,
and turn the screen to green raster.
5. Move the deflection yoke backward.
6. Bring the long lug of the purity magnets on the short
lug and position them horizontally. (Fig2)
7. Adjust the gap between two lugs so that the GREEN
RASTER will come into the center of the screen. (Fig.
3)
8. Move the deflection yoke forward, and fix the position
of the deflection yoke so that the whole screen will
become green.
9. Insert the wedge to the top side of the deflection yoke
so that it will not move.
10. Imput a crosshatch signal.
11. Verify that the screen is horizontal.
12. Input red and blue raster signals, and make sure that
purity is properly adjusted.
CRT
WEDGE
DEFLECTION YOKE
P
4 6
P: PURITY MAGNET
4: 4-POLES (convergence magnets)
6: 6-POLES (convergence magnets)
P/C MAGNETS
Fig. 1
PURITY MAGNETS
Long lug
Short lug
Bring the long lug over the short lug
and position them horizontally.
Fig. 2
(FRONT VIEW)
GREEN RASTER
CENTER
Fig. 3
17
STATIC CONVERGENCE ADJUSTMENT
1. Input a crosshatch signal.
2. Using 4-pole convergence magnets, overlap the red
and blue lines in the center of the screen (Fig. 1) and
turn them to magenta (red/blue).
3. Using 6-pole convergence magnets, overlap the
magenta (red/blue) and green lines in the center of the
screen and turn them to white.
4. Repeat 2 and 3 above, and make the best
convergence.
DYNAMIC CONVERGENCE ADJUSTMENT
1. Move the deflection yoke up and down and overlap
lines in the periphery. (Fig. 2)
2. Move the deflection yoke left to right and overlap the
lines in the periphery. (Fig. 3)
3. Repeat 1 and 2 above, and make the best
convergence.
After adjustment, fix the wedge at the original position.
Fasten the retainer screw of the deflection yoke.
Fix the 6 magnets with glue.
(FRONT VIEW)
Fig. 1
(FRONT VIEW)
RED GREEN BLUE
BLUE
RED
GREEN GREEN
RED BLUE
BLUE GREEN RED
Fig.2
(FRONT VIEW)
RED GREEN BLUE BLUE GREEN RED
RED
GREEN
BLUE
BLUE
GREEN
RED