Campey - Raycam - Aera Seeder - Serial No. I2042 Onwards

OPERATOR & PARTS
Serial # starting at I2042
MANUAL
TABLE OF CONTENTS
ITEM INTRODUCTION SAFETY CALIBRATION STANDARD ROLLER ASSEMBLY DOUBLE ROLLER ASSEMBLY KNIFING ROLLER ASSEMBLY STORAGE PARTS WARRANTY PAGE 2 3 4 5 6 7 8 9-17 18
INTRODUCTION
CONGRATULATIONS!!
Thank you for choosing the Reist Aera Seeder. We feel confident that this equipment will meet your expectations in workmanship, reliability and performance.
This manual is to assist you with the safe operation of the Area Seeder. The Reist Aera Seeder Is a versatile piece of equipment to assist you in various primary and over seeding needs.
MODEL NO.
SERIAL NO.
. 2
SAFETY
CAUTION !
1.
For proper safe operation we recommend that the tractor be equipped with an approved Roll-Over Protective Structure and Safety Belt. Do not operate an engine in a confined or non-ventilated area. Do not perform any adjustments or repairs with engine running. Always lower 3 PT hitch to ground before performing adjustments or repairs. Do not operate on excessive incline and always be careful when turning on slopes. Never carry passengers on implement or tractor. Never let a child operate machinery. Hydraulic fluid under pressure can cause serious injury. Do Not use your hands to locate leaks. It is the owners responsibility to make sure that all operators read this manual before operating the equipment.
2. 3. 4. 5. 6.
7. 8.
9.
Calibration
Calibrating Seed Flow

To calibrate the seed flow rate, you need a weigh scale and small container. Pour seed into seed box. (Each kind of seed needs to be calibrated separately). Insert calibration tray in bottom of seeder on mounts. Set Seed Rate Indicator to an approximate seed rate . With seed flow open, drive the distance of 100 feet. (drive at the same speed as what you are going to drive when seeding). Weigh seed in the calibration tray and multiply by 2. This equals pounds per thousand feet. Example: 4lb x 2 = 8lb per thousand square ft.
1. 2. 3. 4. 5.
Calabration Tray
Seed Rate Indicator
Seed Level Indicator
Seed flow open close indicator
4 Standard Roller Assembly
Standard
B
Cone Spike Roll Seed

A
Smooth Roll Brush
Great for primary and over seeding For primary seeding, the spike roll breaks up clumps and packs the ground. The seed is then dropped by the seeder and the brush lightly covers the seed. The smooth roll presses the soil to keep the moister in the ground. For over seeding the spiked roll pokes small holes into the ground. to moisture, The seed that falls onto the grass is brushed into the holes created by the spike roller. The smooth roll presses down to cover the seed and keep the moisture in.
4 3
Double Spike Rolls (Optional)

3
Spike Roll Seed Brush Spike Roll

D raw n B y:
Double the Number of HolesLMartin TOLERANCES UNLESS TITL E Over seeding with two spiked rolls has twice the number of holes than the standard OTHERWISE NOTED roller assembly. Both rolls poke small holes into the ground. Seed that falls onto the N O S IZE DWG B end views operator manual grass is brushed into the small holes created by the spike rolls. C:\LE S\R ei st p ro du cts\Ove r Se ed ers \Ov er S ee de r 4\Ove
-FRAC TI ONA L T OLE RANC ES A RE ` 1/16 -.x DECI MAL TOLE RA NCE S ARE ` .062 -.xx DECIM AL TOLERA NC E S ARE ` . 015 -.xxx DECIM AL TOLERA NC E S ARE ` . 001 -AN GLE TOLERA NCE S ARE `.5 IF I N D OUB T AS K!
11/1/2005
N OT TO S CA LE
Ma teri a l
SH E
Th is d ra wi ng is the pr op erty o f R e ist Ind us tr ie s In c. is c on fi d en ti al an d m ust n ot be o r di scl os ed i n w h ol e o r i n p ar t to a ny pa rty wi tho ut the exp re ss w ritten au tho rity o f
Knifing Rolls (Optional)

2
Knifing Roll Knifing Roll Seed

A
Knifing Rolls Ph on WithTOLERANCES UNLESS the knives slice into the ground doinge : a9-1 5 01 the Knifing Rolls 1- 51 9-6 6 number of things. TITL E OTHERWISE NOTED It aerates, thatches, loosens and brings up dead grass and other growth between the S IZE DWG O RE V grass and soil. It slices theBroots Nwhich causes the grass to grow thicker. end views operator manual
LMartin 11/1/2005
-FRACTI ONA L T OLE RAN CES A R E ` 1/16 -.x DECI MAL TOLE RA NCE S ARE ` .062 -.x x DECIM AL TOLERA NC E S ARE ` . 015 -.x xx DECIM AL TOLERA NC E S ARE ` . 001 -ANGLE TOLERA NCE S ARE `.5 IF I N DOUB T AS K!
D raw n B y:
C:\LE S\R ei st p ro du cts\Ove r Se ed ers \Ov er S ee de r 4\Ove rs Se e de r Do u bl e Sp ik e as se mbl y 4 . Ma teri a l N OT TO S CA LE SH EE T 1 OF 1
Th is d ra wi ng is the pr op erty o f R e ist Ind us tr ie s In c. is c on fi d en ti al an d m ust n ot be co pi ed , re p rod u ced o r di scl os ed i n w h ol e o r i n p ar t to a ny pa rty wi tho ut the exp re ss w ritten au tho rity o f R e ist Ind us tr ie s In c.
Storage
1. 2. 3. 4.
5. 6.
Store in dry ventilated area. Set on either concrete pad, some wood blocks, or plywood. Store with hydraulic cylinder piston rod in retracted position. Clean before putting into storage. Touch-up paint as needed. Oil seeder chain
PARTS
Aera Seeder Frame
PARTS
List
Part numbers with spaces, enter width of Aera Seeder in inches. Example: 5027_ _ Enter as:502772 Parts List ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 QTY 1 1 3 1 1 2 2 2 1 4 1 3 2 1 1 1 1 1 1 1 1 2 1 1 1 2 4 1 2 3 4 1 1 2 1 2 1 1 1 4 5 2 2 1 1 1 1 1 1 1 1 2 12*2 12FL 12FLSN 134-022 142 14N 20401708 315-709 381 3834 383503 38CLN 38F 40B21-3/4 40RC 5027 5057 5059 5060 5085_ _ 5087_ _ 5088 5090 _ _ 5092 5093_ _ 516112 5161C 5165 516F 516N 516N 585 586 58F 58N 58N 5004 5005 GF MST47 SH-9 1434 14N 5086_ _ 5094 14FL 14N 3305471 5095 5096 TE1588-203-1016 UC204012 PART NUMBER Bolt Washer Flange Nut Knob 1/4x2 NC Bolt 1/4 NC Nut Idler Sprocket Snap Bushing Bolt Bolt Hair pin Lock Nut Washer Sprocket Drive Chain (not showen) Cylinder Assembly Rate Lever Rate Lever bolted Mount Center Agitater Brg Seed Insert Aera Seeder Frame Calibration Tray Aera Seeder Lid Shield Agitater Shaft Hex Bolt Carriage Bolt Bolt Washer Hex Nuts Nut 5/8x5 NC Bolt 5/8x6 NC bolt 5/8 Flat Washer Nut 58 NC Nut Tightener Arm Tightener Bushing 14 NF Grease Zerk Brg Flange Tarp Strap Bolt Nut SS Seed Slide Cyl Mount Washer Nut Seed Level Ball Seed Level Arrow Seed Level Rod Chain Tensioner Bearing Insert DESCRIPTION
10
PARTS
Cylinder
Part numbers with spaces, enter width of Aera Seeder in inches. Example: 5027_ _ Enter as:502772
11
PARTS
Standard Roll Assembly
12
PARTS
Spiked Drive Roll
Spiked Drive Roll
13
PARTS
Broom & Scraper
14
PARTS
Knifing Assembly
15
PARTS
Double Spike Roll
16
PARTS
Double Spike Roll 2nd Position
17
WARRANTY
All new Reist machinery is warranted to be free from defects in material or workmanship, which may cause failure under normal usage and service when used for the purpose, intended, for a period of 12 months. This warranty applies only to a new Reist product, there being no warranty of any nature in respect to new products that have been modified or altered, repaired, neglected, or used in any way, which, in the opinion of Reist adversely affects its performance. In the event of failure of a part or parts, and upon inspection, Reist is satisfied that failure is due to defective material or workmanship within 12 calendar months, from the date of delivery to an end user, such defective part or parts will be repaired or replaced by Reist at his business location. It is the responsibility of the buyer, at his expense, to transport the machine or equipment to the manufacturer service shop or, to an authorized service depot or, alternatively, to reimburse Reist for any travel or transportation expense involved in fulfilling this warranty. When requested by Reist, part or parts shall be returned for inspection, transportation prepaid, to a place designated by Reist. IN NO EVENT SHALL THE BUYER BE ENTITLED TO RECOVER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF PRODUCT, INCONVENIENCE, RENTAL OR REPLACEMENT EQUIPMENT, LOSS OF PROFIT, OR OTHER COMMERCIAL LOSS.
This warranty becomes void and null if the equipment is modified, breaks down as the result of an accident, is not operated according to manufacturers recommendations, damaged by negligence or if maintenance has not been carried out as specified.
THIS WARRANTY IS NOT TRANSFERABLE

Proof of Purchase
Date of purchase (yyyy mm dd) Model Serial #
Dealer puchased from
City
State or Province
Country
First Name
Last Name
Phone # (include area code)
Address Reist Industries Inc. 100 Union St. Elmira Ontario N3B 2Z2 City Postal Code
State or Province
Country
519-669-1501
Proof of Purchase
Date of purchase (yyyy mm dd) Model Serial #
Dealer puchased from
City
State or Province
Country
First Name
Last Name
Phone # (include area code)
Address Reist Industries Inc. 100 Union St. Elmira Ontario N3B 2Z2 City Postal Code
State or Province
Country
519-669-1501
18
Reist Industries (Elmira) Ont. 100 Union St., Elmira Ontario, Canada, N3B 2Z2 www.reistindustries.com
19
(Revised March 2008)

Campey - Raycam - Aera Seeder - Serial No. I2042 Onwards

Uploaded by

Copyright:

Available Formats

Campey - Raycam - Aera Seeder - Serial No. I2042 Onwards

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Campey - Raycam - Aera Seeder - Serial No. I2042 Onwards

Uploaded by

Copyright:

Available Formats

OPERATOR & PARTS

Serial # starting at I2042

Calibrating Seed Flow

Seed Rate Indicator

Seed Level Indicator

Seed flow open close indicator

4 Standard Roller Assembly

Cone Spike Roll Seed

Smooth Roll Brush

Double Spike Rolls (Optional)

Spike Roll Seed Brush Spike Roll

Knifing Rolls (Optional)

Knifing Roll Knifing Roll Seed

C:\LE S\R ei st p ro du cts\Ove r Se ed ers \Ov er S ee de r 4\Ove rs Se e de r Do u bl e Sp ik e as se mbl y 4 . Ma teri a l N OT TO S CA LE SH EE T 1 OF 1

Aera Seeder Frame

Standard Roll Assembly

Spiked Drive Roll

Spiked Drive Roll

Broom & Scraper

Double Spike Roll

Double Spike Roll 2nd Position

THIS WARRANTY IS NOT TRANSFERABLE

Dealer puchased from

Phone # (include area code)

Dealer puchased from

Phone # (include area code)

You might also like