Brickwork NVQ and Technical Certificate Level 2, 2nd Edition

Find out
How are the different soil tests carried out?

Soil investigations are critical. Samples of the soil are taken from various points around the site and tested for their composition and for any contamination. Some soils contain chemicals that can seriously damage the foundation concrete. These chemicals include sodium and magnesium sulphates. The effects of these chemicals on the concrete can be counteracted with the use of sulphate-resistant cements. Many different tests can be carried out on soil. Some are carried out on site; others need to be carried out in laboratories. Tests on soil include:

Did you know?

Site investigations or surveys will also establish the contours of the site. This will identify where certain areas of the site will need to be reduced or increased in height. An area of the site may need to be built up in order to mask surrounding features outside the boundaries of the proposed building project

penetration tests to establish density of soil compression tests to establish shear strength of the soil or its bearing capacity various laboratory tests to establish particle size, moisture content, humus content and chemical content.

Once all site investigations have been completed and all necessary information and data has been established in relation to the proposed building project, site clearance can take place.

Site clearance
The main purpose of site clearance is to remove existing buildings, waste, vegetation and, most importantly, the surface layer of soil referred to as topsoil. It is necessary to remove this layer of soil, as it is unsuitable to build on. This surface layer of soil is difficult to compact down due to the high content of vegetable matter, which makes the composition of the soil soft and loose. The topsoil also contains various chemicals that encourage plant growth, which may adversely affect some structures over time. The process of removing the topsoil can be very costly, in terms of both labour and transportation. The site investigations will determine the volume of topsoil that needs to be removed calculations used to establish these volumes are explained in Chapter 7 Numeracy skills.

Find out
How can plant growth affect some structures?

Removing soil from a site

226
ISBN_C13_pp223_234.indd 226 18/4/08 14:47:16

Chapter 13 Site preparation, excavations and foundations

In some instances, the excavated topsoil may not be transported off site. Where building projects include garden plots, the topsoil may just need to be stored on site, thus reducing excessive labour and transportation costs. However, where this is the case, the topsoil must be stored well away from areas where buildings are to be erected or materials are to be stored, to prevent contamination of soils or materials. Once the site clearance is complete, excavations for the foundations can start.

Trench excavation
In most modern-day construction projects, trenches are excavated by mechanical means. Although an expensive method, it reduces labour time and the risks associated with manual excavation work. Even with the use of machines to carry out excavations, an element of manual labour will still be needed to clean up the excavation work: loose soil from both the base and sides of the trench will have to be removed, and the sides of the trench will have to be finished vertically. Manual labour is still required for excavating trenches on some projects where machine access is limited and where only small strip foundations of minimum depths are required. Trenches to be excavated are identified by lines attached to and stretched between profiles. This is the most accurate method of ensuring trenches are dug to the exact widths. Excavation work must be carefully planned as workers are killed or seriously injured every year while working in and around trenches. Thorough risk assessments need to be carried out and method statements produced prior to any excavation work commencing. Potential hazards are numerous and include: possible collapse of the sides of the trench, hitting hidden services, plant machinery falling into the trench and people falling into the trench. One main cause of trench collapse is the poor placement of materials near to sides of the trench. Not only can materials cause trench collapse, but they may also fall into the trench onto workers. Materials should not be stored near to trenches. Where there is a need to place materials close to the trench for use in the trench itself, always ensure these are kept to a minimum, stacked correctly and used quickly and, most importantly, ensure the trench sides are supported.

Trenches are often excavated by mechanical means

227
ISBN_C13_pp223_234.indd 227 18/4/08 14:47:19

Brickwork NVQ and Technical Certificate Level 2, 2nd Edition

Trench support

Did you know?

The Health and Safety Executive has produced detailed documents that deal exclusively with safety in excavations. These documents can be downloaded from the HSE website or obtained upon request direct from the HSE. Regulations relating to safety in excavations are set out in the Construction Regulations and these must be strictly adhered to during the work

The type and extent of support required in an excavated trench will depend predominantly on the depth of the trench and the stability of the soil. Traditionally, trench support was provided just by using varying lengths and sizes of timber, which can easily be cut to required lengths. However, timber can become unreliable under certain loadings, pressures and weather conditions and can fail in its purpose. More modern types of materials have been introduced as less costly and timeconsuming methods of providing the required support. These materials include steel sheeting, rails and props. Trench support can be provided with a mixture of both timber and steel components. Here you can see the methods of providing support in trenches with differing materials and a combination of these materials.
Poling boards

Wedges Wallings

Poling boards

Puncheons 1.800 centres Struts positioned at 1.800 centres

Sole plate

Figure 13.1 Timber used in trench support

228
ISBN_C13_pp223_234.indd 228 18/4/08 14:47:21

Chapter 13 Site preparation, excavations and foundations

Steel sheeting Steel sheet

Timber walling boards Steel props

Steel trench prop

Timber walling boards secured to steel sheeting with brackets

Figure 13.2 Combination of timber and steel used in trench support The amount of timber or other materials required to provide adequate temporary support will be determined by the characteristics of the soil and the soils ability to remain stable during the time over which the work is carried out. The atmospheric conditions will also affect the soils ability to remain stable. The longer the soil is exposed to the natural elements, the more chance there is of the soil shrinking or expanding. Without support, soil will have a natural angle of repose: in other words, the angle at which the soil will rest without collapsing or moving. Again, this will be affected by the natural elements to which the soil is exposed. It is virtually impossible to accurately establish the exact angle at which a type of soil will settle, so it is Title: Revised Level always advisable to provide more support than is actually required. 2 Bricklaying Text Book Site engineers will carry out calculations in relation to the support requirements for trenches. Temporary barriers or fences should also be provided around the perimeters of all trenches, to prevent people falling into the trenches and also to prevent materials from being knocked into them. Good trench support methods will incorporate extended trench side supports, which provide a barrier similar to a toe board on a scaffold to prevent materials being kicked or knocked into the trench. Where barriers or fences are impractical, then trenches should be covered with suitable sheet materials.
Job No: J7198 Fig No: 978 0435325817_aw_015

229
ISBN_C13_pp223_234.indd 229 18/4/08 14:47:21